Attachment 0001 - Drawing 9829 REV B.pdf

DRAWING REVIEW CHECKLIST

Questions to be answered by Design Engineer:

Y N NA

1. Is there an alternate tool or design that could be used to perform this task?

if yes, please explain what and why not used (i.e., cost, time, etc.).

2. Are cracks, voids, weld seams, or other areas where explosives could accumulate eliminated if it is used in and explosive atmosphere?

3. Are all pinch points eliminated so that neither explosive can be pinched or personnel injured?

4. Is the material specified appropriate for explosive atmosphere if used in this environment?

5. Are all Electrical components properly rated for the type of location where it will be used?

7. Are all commercial components specified for use adequately rated for the type of location where it will be used?

8. Does the item have adequate safety interlocks designed (i.e., two-handed controls, etc.)?

9. Is the item strong enough to perform at 150% of intended use (i.e., weight, pressure, etc.)?

10. Is the item designed with ergonomic considerations (i.e., proper height, ?

repetitive movements, proper gripping, line of sight, strength required to operate?

11. Is the item designed for minimal maintenance and does it provide easy access if maintenance is required?

12. Is the item designed to allow lockout/tag out when maintenance is performed?

13. If required, can the item be decontaminated without destroying its intended use?

14. If required, had adequate special fire protection been built into the design?

15. Has the item been designed to interact with other components within the system?

Signature

6. Is adequate guarding/shielding designed into the item?

16. Distribution Statment: A B C D E F

A

CAAA Form 702-168 Nov. 2019

NOMENCLATUREITEM

NO.

NO.

REQ'D MATERIAL

FOR DRAWING NO.

TITLE

CHECKED BY

FABRICATION

SAFETY

DATE

DATE

DATE

DATEAPPROVAL

DRAWN BY

DATE D SCALE DWG. NO. SHEET

OF

REVISIONS

LTR DESCRIPTION DATE DATE

BREAK ALL

SHARP EDGES

UNLESS OTHERWISE NOTED, TOLERANCES ARE:

DECIMALS: .XXX ± .005, .XX ± .01, .X ± .1 ANGLES ±30'

CRANE ARMY AMMUNITION ACTIVITY

ENGINEERING DIVISION

3X 120° 5.375 ±.020 I.D.

7/16

.105 ±.010

WALL THICKNESS

.13 TO .25

.50 1.00

25.37 +.25/-.00

A MATERIAL TOLERANCE

SPECIFIED D. BADE 10/20/2011

B SHIPPING NOTES

ADDED

RJW 12/18/12

- STAPLE THE INSTALLED END PLUG IN 3 PLACES APPROXIMATLY 120°

APART. STAPLE FROM THE OUTSIDE IN. STAPLE TO BE WELL CLINCHED

ON THE INSIDE OF THE METAL END PLUG.

- STAPLES: No. 8, 7/16" CROWN, 1/2" LEG.

- STAPLES WILL BE PLACED AS DEEP AS POSSIBLE UP INTO THE PLUG. THEY

WILL BE LOCATED AT LEAST 1/2" IN FROM THE EDGE OF THE METAL PLUG

AS SHOWN (NOT FROM THE END OF THE TUBE).

- THE CROWN OF THE STAPLE ON THE OUTSIDE OF THE TUBE WILL PRESS

SECURELY AGAINST THE OUTSIDE OF THE TUBE SO THAT IT IS A MAXIMUM

THICKNESS OF THE STAPLE WIRE ABOVE THE OUTSIDE CIRCUMFERENCE

OF THE TUBE.

- THE STAPLE CROWN MAY INDENT THE TUBE BUT IT WILL NOT CUT INTO

THE TUBE EXTERIOR.

SERRATED METAL PLUG TO BE:

A. 5.375" DIA

B. 5.445" FLARE

C. 1.000" DEPTH

D. MADE 126 GAUGE COLD ROLLED STEEL,

(INDUSTRY STANDARD .0159 -TO .0199 THICK)

ONE SUPPLIER IS AMCLO GROUP, INC.

1. APPLY A 0.005" THICK MOISTURE RESISTANT SILVER

FOIL WRAP TO THE EXTERNAL OF THE TUBE.

2. BOTH END PLUGS SHOULD BE METAL AND FIT

TIGHTLY.

3. THE TUBE SHOULD BE CONSTRUCTED OUT OF

0.095" WALL THICKNESS CHIPBOARD.

4. INTERIOR SHALL BE LINED WITH A 0.005" THICK

SILICONE COATED KRAFT.

5. TUBES WILL WITHSTAND A LONGITUDINAL CRUSH FORCE OF

AT LEAST 1,400 LBS. WHEN TESTED ON A COMPRESSION FORCE

TEST MACHINE USING AN APPROACH VELOCITY OF 20" PER MINUTE.

THE FORCE IS CENTERED OVER THE TUBE ENDS AND APPLIED

THROUGH METAL PLATES PLACED OVER EACH TUBE END.

6. ENDS OF TUBE WILL BE SQUARE CUT.

SHIPPING REQUIREMENTS:

- TUBES TO BE PACKED AND SHIPPED 192 TOTAL PER PALLET WITH

64 PER ROW AT THREE ROWS TALL (MAX).

- ALL FOUR VERTICAL CORNERS HAVING 3" X 3" -0.120" THICK FIBERBOARD/

LAMINATED EDGE PROTECTORS. EACH HORIZONTAL ROW, BOTTOM AND TOP MUST

BE COVERED AND PROTECTED WITH SINGLE WALL 200 LBS TEST CORRUGATED

CARDBOARD SHEET OR EQUIVALENT. SECURE ALL AS REQUIRED TO PALLET WITH

SHRINK WRAP.

- PALLET TO BE 40" X 48".

FIRST USED IN BUILDING 2728 AS GRENADE TUBE FOR D563, 155mm PROJECTILE

DEMIL. THE 88 EACH GRENADES ARE PUSHED INTO THIS TUBE. DRAWING TAKEN

FROM SKETCH #S0359.

GRENADE TUBE FOR D563

155mm PROJECTILE DEMIL

9829 1 1

RJ WILSON

19 APR 2005

J BIRKHIMER 4/20/05

JIM BLAKE 4/20/05

W F SHAREN 5/10/05

SONNY DANT 5/16/05

.06 A

END PLUG -

INSTALLED ONE END ONLY*

STAPLE

- A -

METAL SERATED END PLUG PROVIDED.

2 EA. REQ'D. 1 INSTALLED AS SHOWN AND 1

SEPERATE FOR FIELD INSTALLATION.

DISTRIBUTION STATEMENT "A"

matthew.todd Text Box matthew.todd Text Box matthew.todd Text Box matthew.todd Text Box