ATTACH_Tech_Data.pdf

NCTRF PD-08-15C

RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS

(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA

MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT:

http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx

FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE

SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE

ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE

APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION,

IN WHICH CASE THE AMENDMENT DATE CONTROLS.

DATE: 14 August 2015

PATTERN DATE: 22 July 2015 sample size is 12MR

The basic cloth for the slacks will be Government Furnished Material conforming to MIL-C-823, Type I, Class 5, 15 ounces per linear yard, NSN 8305-00-350-5655. The shade standard for the GFM is Blue 3346, Piece No.

10164.

ADDITIONAL INFORMATION FOR A-A-50198:

THE GIMP THREAD SHALL BE MADE IN ACCORDANCE

WITH A-A-50198A, DATED 6/21/00

NO ADDITIONAL INFORMATION FOLLOWS:INTERIM SPECIFICATION CHANGES TO A-A-

50199

NO ADDITIONAL INFORMATION

ADDITIONAL INFORMATION FOR A-A-52094A THREAD, COTTON

NO ADDITIONAL INFORMATION

(ref. T1481)

ADDITIONAL INFORMATION FOR A-A-52106:

INTERIM CHANGES TO A-A-52106:

PAGE 1, UNDER ABSTRACT. AFTER "THE CLASS 3 CLOTH IS

INTENDED FOR USE AS LINING MATERIAL IN DRESS COATS."

ADD "CLASS 4 CLOTH IS INTENDED TO BE USED AS A

GARMENT LINING. CLASS 5 CLOTH IS INTENDED FOR USE

AS A NECKTIE AND NECKTAB OUTERSHELL FABRIC."

PAGE 1, CLASSIFICATION. ADD CLASS 4 - LIGHT WEIGHT

2.4 OZ; 2/1 RIGHT HAND TWILL USING 100% FILAMENT

POLYESTER SINGLE PLY YARNS FOR BOTH CLASS 4 AND CLASS 5.

CLASS 5 - MEDIUM WEIGHT 3.0 OZ; 5/1 HERRINGBONE TWILL

PAGE 1, PARAGRAPH 1.1 CLASSIFICATION: ADD PAGE 1,

GENERAL DESCRIPTION. LINE 5 AFTER "YARNS" ADD

"THE CLASS 4 CLOTH SHALL BE A TW0 UP-ONE DOWN RIGHT

HAND TWILL. THE CLASS 5 CLOTH SHALL BE A FIVE UP-ONE

DOWN HERRINGBONE TWILL. THE YARNS FOR CLASS 4 CLOTH

SHALL BE SINGLE PLY WITH A NOMINAL DENIER OF 70 FOR

THE WARP YARNS AND 150 FOR THE FILLING YARNS.

PAGE 2, TABLE I CLOTH REQUIREMENTS AFTER CLASS 3"

ADD INFORMATION FOR "CLASSES 4 AND 5"

CHARACTERISTIC CLASS 4 CLASS 5

MATERIAL CONTENT, PERCENT:

POLYESTER 100% 100%

COTTON 0 0

RAYON 0 0

COLORFASTNESS TO:

PERSPIRATION GOOD GOOD

SUBLIMATION GOOD GOOD

WET DRY-CLEANING GOOD GOOD

CROCKING (MIN.) 3.5 3/ 3.5 3/

(BLACK OR DARK

BLUE COLORS) 1.0 3/ 1.0 3/

LABILE SULFUR CONTENT 4/ 4/

WEIGHT, OZ. /SQ. YD.(MIN.) 2.4 3.0

YARNS PER INCH (MIN.)

WARP 124 140

FILLING 76 75

BREAKING STRENGTH POUNDS (MIN.)

WARP 140 160

FILLING 110 130

TEARING STRENGTH POUNDS (MIN.)

WARP 5.0 14.0

FILLING 3.0 10.5

PAGE 2, PARAGRAPH 2.1 GENERAL DESCRIPTION: AFTER

"THE CLASS 5 CLOTH SHALL BE A FIVE UP-ONE DOWN

"THE CLASS 5 CLOTH, USING 100 % FILAMENT HERRINGBONE

TWILL." INSERT "THE CLASS 6 CLOTH POLYESTER SINGLE PLY

WITH BLACK 70 DENIER NOMINAL WARP AND AIR FORCE

BLUE 1622 150 DENIER NOMINAL FILLING YARNS." USING

100% FILAMENT POLYESTER SINGLE PLY WITH 70 DENIER NOMINAL

IN THE WARP AND 150 DENIER NOMINAL IN THE FILLING DIRECTION."

PAGE 2, PARAGRAPH 2.2 PHYSICAL REQUIREMENTS:

TABLE I. CLOTH REQUIREMENTS, ADD THE FOLLOWING:

PAGE 3, AFTER 2.3 LENGTH AND PUT-UP. ADD THE FOLLOWING

NEW PARAGRAPH: "2.4 COLOR. THE COLOR OF THE FINISHED

CLOTH SHALL BE AS SPECIFIED (SEE 5.1) AND SHALL MATCH THE STANDARD

SAMPLE FOR SHADE. CLASS 5 FABRIC IS MADE

FROM DYED WARP AND DYED FILLING IN TWO DIFFERENT COLORS.

CLASS 5 FABRIC SHALL BE AIR FORCE SHADE BLUE 1622 ROLL #89-2.

(ref. T1514 - 5/23/06)

ADDITIONAL INFORMATION FOR A-A-55634A, 23 MARCH 2004:

SPECIAL NOTE!! ALL SLIDE FASTENERS USED ARE TO BE MEASURED FROM "STOP

TO STOP". RECOMMEND THAT THIS MEASUREMENT BE TAKEN RANDOMLY BEFORE

SLIDE FASTENERS ARE SEWN TO THE ITEMS, COVERALL, OR ANY ITEM REFERRED TO

IN THE SOLICITATION. "THE QAR WILL REJECT ANY SLIDE THAT IS NOT LAYING

FLAT AFTER IT IS SEWN INTO/ONTO AN ITEM." SPECIAL INFO ON ITEMS THAT

UTILIZE SLIDE FASTENERS IS GIVEN BY "ALL USING MILITARY PERSONNEL".

ADDITIONAL INFORMATION FOR MIL-B-17143:

NO ADDITIONAL INFORMATION FOLLOWS.

(Ref. T0738)

INTERIM SPECIFICATION CHANGES TO MIL-C-21852F:

PAGE 1, CLASSIFICATION. PARA. 1.2, LINE 5 UNDER

"TYPE III", DELETE "2.0" AND SUBSTITUTE "1.8" AND

DELETE "68" AND SUBSTITUTE "61".

PARAGRAPH 3.4, TABLE I. PHYSICAL REQUIREMENTS.

UNDER "TYPE III", "WEIGHT" REQUIREMENT, DELETE

"2.0 (68)" AND SUBSTITUTE "1.8 (61)".

PAGE 13, PARA.4.5.4 SPECTRAL REFLECTANCE TEST.

LINE 4, DELETE "HALON" AND SUBSTITUTE

"POLYTETRAFLUOROETHYLENE (PTFE)".

(ref. T1036 - May 19, 2006)

MIL-DTL-32075: LABEL FOR CLOTHING, EQUIPAGE,

AND TENTAGE, GENERAL USE REPLACES DDD-L-20

(Ref. T0451 - June 19, 2007)

INTERIM SPECIFICATION CHANGES TO MIL-DTL-32075:

PAGE 4, PARA. 3.3.5, AFTER "TYPE III OR IV, CLASS 4 OF" DELETE "DDD-L-

20" AND REPLACE "MIL-DTL-32075,".

PAGE 6, TABLE I, "PHYSICAL REQUIREMENTS OF THE

TYPE VI FINISHED LABEL." UNDER "TEARING

STRENGTH" DELETE: "(LB.) MINIMUM" AND

SUBSTITUTE: "(GNS) MINIMUM."

PAGE 12, PARA 3.3.2.17, AFTER "NSN" ADD

"AND THE UNIVERSAL PRODUCT CODE (UPC)

SUPPLIED BY THE GOVERNMENT, FOR ALL NSNs."

ADDITIONAL INFORMATION FOR ASTM-D-6193(2004)OR LATEST VERSION:

NO ADDITIONAL INFORMATION FOLLOWS.

(Ref. T8068 - May 18, 2006)

ADDITIONAL INFORMATION FOR ANSI/ASQC Z1.4:

NOTE: THE MOST RECENT VERSION OF THIS DOCUMENT SHOULD BE USED.

APPLICATION FOR COPIES SHOULD BE ADDRESSED TO:

AMERICAN SOCIETY FOR QUALITY

600 NORTH PLANKINTON AVENUE

MILWAUKEE, WISCONSIN 53203

(Ref. T0795 - May 17, 2006)

MIL-STD-129 CURRENT REVISION UNLESS OTHERWISE SPECIFIED

- DEPARTMENT OF DEFENSE STANDARD PRACTICE

- MILITARY MARKING FOR SHIPMENT AND STORAGE

ADDITIONAL INFORMATION FOR MIL-STD-656:

INTERIM CHANGES TO MIL-STD-656C

PAGE 18, DEFECT XV. POCKET OR FLAPS, S.

HIP POCKET: ADD NEW DEFECT:

"3. CORD (WELTS) OUT OF HORIZONTAL ALIGNMENT

WITH WAISTBAND WHEN MEASURED FROM BOTTOM OF

WAISTBAND TO TOP CORNERS OF WELT BY:

. D S U

-MORE THAN 1/2 INCH * 3 2

-MORE THAN 1/4 UP TO 1/2 INCH 3 3 2

-UP TO 1/8 MORE 1/4 INCH 2 2 1

INTERIM CHANGES TO MIL-STD-656C:

PAGE 5, TABLE I DELETE IN ITS ENTIRETY AND

SUBSTITUTE "TABLE I SAMPLING PROVISIONS FOR END

ITEM VISUAL EXAMINATION OF DRESS (D) SLACKS:

NORMAL INSPECTION:

LOT SIZE SAMP SIZE MAX ACCP PT VALUE

. 3&2 PT 3.2 &1 PT

. DEFECTS DEFECTS

UP THRU 90 20 3 PT 6 PT

91 - 150 32 5 PT 9 PT

151 - 280 50 7 PT 13 PT

281 - 500 80 9 PT 17 PT

501 - 1200 125 14 PT 25 PT

1201 - 3200 200 18 PT 33 PT

REINSTATE NORMAL INSPECTION (SEE 5.5.4B). THE

3201 - 10,000 315 24 PT 48 PT

SECOND VALUE IS THE MAXIMUM ACCEPTABLE POINT

10,001 - 35,000 500 35 PT 72 PT

35,001 AND OVER 800 55 PT 110 PT

TIGHTENED INSPECTION:

UP THRU 150 32 2 PT 5 PT

151 - 280 50 3 PT 7 PT

281 - 500 80 5 PT 11 PT

501 - 1200 125 9 PT 17 PT

1201 - 3200 200 13 PT 26 PT

3201 - 10,000 315 20 PT 39 PT

10,001 - 35,000 500 30 PT 59 PT

35,001 AND OVER 800 45 PT 89 PT

REDUCED INSPECTION:

UP THRU 280 20 2-6 PT 11 PT

281 - 500 32 3-9 PT 15 PT

501 - 1200 50 5-10 PT 18 PT

1201 - 3200 80 8-13 PT 24 PT

3201 - 10,000 125 12-17 PT 28 PT

10,001 - 35,000 200 17-21 PT 33 PT

35, 001 AND OVER 315 23-29 PT 47 PT

1/ IF THE FIRST VALUE IS EXCEEDED BUT THE SECOND

VALUE HAS NOT BEEN EXCEEDED, ACCEPT THE LOT BUT

REINSTATE NORMAL INSPECTION (SEE 5.5.4B). THE

SECOND VALUE IS THE MAXIMUM ACCEPTABLE POINT

VALUE.

TABLE II DELETE IN ITS ENTIRETY AND SUBSTITUTE

"TABLE II SAMPLING PROVISIONS FOR END ITEM

VISUAL EXAMINATION OF SEMI-DERSS (SD) SLACKS"

NORMAL INSPECTION:

LOT SIZE SAMP SIZE MAX ACCP PT VALUE

. 3&2 PT 3.2.&1 PT

. DEFECTS DEFECTS

UP THRU 500 50 7 PT 14 PT

501 THRU 1200 80 9 PT 20 PT

1201 THRU 3200 125 14 PT 26 PT

3201 THRU 10,000 200 19 PT 38 PT

10,001 THRU 35,000 315 27 PT 57 PT

35,001 AND OVER 500 41 PT 85 PT

TIGHTENED INSPECTION:

UP THRU 500 50 3 PT 10 PT

501 THRU 1200 80 5 PT 15 PT

1201 THRU 3200 125 8 PT 23 PT

3201 THRU 10,000 200 12 PT 34 PT

10,001 THRU 35,000 315 19 PT 52 PT

35,001 AND OVER 500 27 PT 78 PT

REDUCED INSPECTION:

UP THRU 1200 32 3-8 PT 15 PT

1200 THRU 3200 50 5-9 PT 18 PT

3201 THRU 10,000 80 8-12 PT 24 PT

10,001 THRU 35,000 125 11-15 PT 31 PT

35,001 AND OVER 200 15-53 PT 43 PT

1/ IF THE FIRST VALUE IS EXCEEDED BUT THE SECOND

VALUE HAS NOT BEEN EXCEEDED, ACCEPT THE LOT BUT

REINSTATE NORMAL INSPECTION (SEE 5.5.4B). THE

SECOND

REINSTATE NORMAL INSPECTION (SEE 5.5.4B). THE

SECOND

TABLE III DELETE IN ITS ENTIRETY AND SUBSTITUTE

"TABLE III SAMPLING PROVISIONS FOR END ITEM

VISUAL EXAMINATION OF UTILITY (U) SLACKS"

NORMAL INSPECTION:

LOT SIZE SAMP SIZE MAX ACCP PT VALUE

. 3&2 PT 3.2 & 1 PT

. DEFECTS DEFECTS

UP THRU 500 50 9 PT 17 PT

501 THRU 1200 80 13 PT 20 PT

1201 THRU 3200 125 18 PT 29 PT

3201 THRU 10,000 200 25 PT 42 PT

10,001 AND OVER 315 39 PT 62 PT

TIGHTENED INSPECTION:

UP THRU 500 50 5 PT 11 PT

501 THRU 1200 80 8 PT 17 PT

1201 THRU 3200 125 12 PT 25 PT

3201 THRU 10,000 200 19 PT 38 PT

10,001 AND OVER 315 27 PT 57 PT

REDUCED INSPECTION:

UP THRU 1200 32 5-9 PT 16 PT

1201 THRU 3200 50 8-12 PT 20 PT

3201 THRU 10,000 80 11-14 PT 25 PT

10,001 AND OVER 125 15-19 PT 29 PT

1/ IF THE FIRST VALUE IS EXCEEDED BUT THE SECOND

VALUE HAS NOT BEEN EXCEEDED, ACCEPT THE LOT BUT

REINSTATE NORMAL INSPECTION (SEE 5.5.4B). THE

SECOND VALUE IS THE MAXIMUM ACCEPTABLE POINT

VALUE.

PAGE 20, UNDER XX LABEL ADD THE FOLLOWING:

D. BAR CODE LABEL/TAG

DEFECT POINT VALUE

. D SD U

1. BAR CODE OMITTED OR NOT

. READABLE BY SCANNER. 1 1 1

2. HUMAN READABLE INTERPRETATION

. (HRI) OMITTED OR

. ILLEGIBLE 1 1 1

3. NOT VISIBLE ON FOLDED,

. PACKAGED ITEM. 1 1 1

4. CAUSES DAMAGE TO THE

. ITEM. 3 3 3".

(Ref. T0320)

ADDITIONAL INFORMATION FOR MIL-STD-984:

MIL-STD-984A: PROVISION FOR SIZE LABELING FOR

WOMEN'S UNIFORM CLOTHING 13 SEPT 1994.

EACH WOMAN'S ITEM SHALL HAVE A SEPARATE

SIZE LABEL CONFORMING TO TYPE VI CLASS 2 OF

MIL-DTL-32075 AND BODY DIMENSION LABELING

REQUIREMENT CONFORMING TO MIL-STD-984. THE

LABEL SHALL INDICATE SIZE, BODY DIMENSIONS,

AND STOCK NUMBER AS SHOWN BELOW:

FOR DRESS COATS:

SIZE CODE: 12JP (EXAMPLE)

BUST CIRC: 37-1/2 (EXAMPLE)

HIP CIRC: 38 (EXAMPLE)

HEIGHT: LESS THAN 63 1/2 (P) (EXAMPLE)

FOR SLACKS AND SKIRTS:

SIZE CODE: 12 JP (EXAMPLE)

WAIST CIRC: 29-1/2 (EXAMPLE)

HIP CIRC: 38 (EXAMPLE)

HEIGHT: LESS THAN 63 1/2 (P) (EXAMPLE)

PAGE 5, TABLE 1, ADD THE FOLLOWING SIZES:

HEIGHT: LESS THAN 63 1/2 (P) (EXAMPLE)

STOCK NO: 8410-00-000-0000 (EXAMPLE)

NOTE: ABBREVIATIONS FOR THE APPLICABLE BODY TYPE

SHALL BE "J" FOR JUNIORS , "M" FOR MISSES AND

"W" FOR WOMEN'S.

ABBREVIATIONS FOR THE APPLICABLE LENGTHS SHALL

BE "P" FOR PETITE, "R" FOR REGULAR, AND "T" FOR

TALL.

NOTE: THE INFORMATION FOR EACH SIZE LABEL IS

CONTAINED IN MIL-STD-984 AND IS NOT TO BE

CONFUSED WITH THE FINISHED DIMENSIONS OF THE END

ITEM IN THE SPECIFICATION.

INTERIM CHANGES TO MIL-STD-984:

PAGE 5, TABLE I, DELETE IN ITS ENTIRETY AND

SUBSTITUTE THE FOLLOWING:

SIZE CODE BUST CIRC WAIST CIRC HIP CIRC

INCHES INCHES INCHES INCHES

2M 31-1/2 23-1/2 34 4J 32-1/2 24-1/2 33 4M 32-1/2 24-1/2 35 4W 32-1/2 24-1/2 37 6J 33-1/2 25-1/2 34 6M 33-1/2 25-1/2 36 6W 33-1/2 25-1/2 38 8J 34-1/2 26-1/2 35 8M 34-1/2 26-1/2 37

8W 34-1/2 26-1/2 39 10J 36 28 36-1/2 10M 36 28 38-1/2 10W 36 28 40-1/2 12J 37-1/2 29-1/2 38 12M 37-1/2 29-1/2 40 12W 37-1/2 29-1/2 42 14J 39 31 39-1/2 14M 39 31 41-1/2 14W 39 31 43-1/2 16J 41 33 41-1/2 16M 41 33 43-1/2 16W 41 33 45-1/2 18J 43 35 43-1/2 18M 43 35 45-1/2 18W 43 35 47-1/2 20J 45 37 45-1/2 20M 45 37 47-1/2 20W 45 37 49-1/2 22J 47 39 47-1/2 22M 47 39 49-1/2 22W 47 39 51-1/2 24J 49 41 49-1/2 24M 49 41 51-1/2 24W 49 41 53-1/2 26J 51 43 51-1/2 26M 51 43 53-1/2 26W 51 43 55-1/2 28J 53 45 53-1/2 28M 53 45 55-1/2 28W 53 45 57-1/2

INTERIM CHANGES:

OMISSION OF MARKINGS ON EXTERIOR SHIPPING CONTAINERS OF ITEMS

IN THE DLA TROOP SUPPORT CLOTHING AND TEXTILE (C&T) DIRECTORATE:

THE NOMENCLATURE AND MANUFACTURER'S NAME (WHEN THE NAME IDENTIFIES THE

MATERIAL) SHALL BE OMITTED FROM ALL EXTERIOR SHIPPING CONTAINERS OF DLA

TROOP SUPPORT C&T ITEMS, REGARDLESS OF MODE OF SHIPMENT.

IF THE MANUFACTURER'S NAME DOES NOT IDENTIFY THE MATERIAL AS BEING

CLOTHING, IT MAY REMAIN. NSNS SHALL BE SHOWN ON ALL SHIPPING CONTAINERS

OF C&T ITEMS, THE PACKING LIST SHALL BE PLACED INSIDE THE LAST CONTAINER

TO BE LOADED FOR EACH SHIPMENT. THE WORDS "PACKING LIST HERE" SHALL BE

STENCILED, NOT HAND LETTERED, ON THE CONTAINER.

MIL-STD-147 IS HEREBY REINSTATED AS FOLLOWS:

MIL-STD-147E DEPARTMENT OF DEFENSE

16 MAY 2008 STANDARD PRACTICE