ATTACH_PGC_02444.pdf

RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN

RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY

REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH

IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL AND QUALITY

REQUIREMENTS FOUND ON THE WEB AT:

http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx

FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN

EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE

CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN

EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION

AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE

AMENDMENT DATE CONTROLS.

BERET, WOOL, BLUE 1561, TYPE III, CLASS 2, OFFICER'S WITH FLASH

INSIGNIA

ADDITIONAL INFORMATION FOR A-A-55184A

PATTERN DATE(LINER): 11 FEBRUARY 2003

STANDARD SAMPLE IS AVAILABLE AND IS APPLICABLE

FOR SHADE ONLY - BLUE 1561

THE CONTRACTOR SHALL STAMP LEGIBLY WITH INDELIBLE INK THE LOT

NUMBER ON EACH END ITEM AND OUTER CONTAINER IN THE LOT.

LIST OF DOCUMENTS, EXHIBITS, AND OTHER ATTACHMENTS

A. THIS SOLICITATION/AWARD CONSISTS OF THE FOLLOWING DOCUMENTS,

EXHIBITS, AND OTHER ATTACHMENTS.

B. DLA TROOP SUPPORT CLOTHING AND TEXTILES #ADDITIONAL QUALITY

ASSURANCE REQUIREMENTS DATED August 2021, SUPERSEDES DSCP

4155.3, ADDITIONAL QUALITY ASSURANCE REQUIREMENTS, DATED

OCTOBER, 2018.

Packaging: Preservation: Each beret shall have a cardboard insert conforming to finished dimensions, width and length of table V. There shall be a hole through the center for removal when taking finished dimensions. Unit Packing: Each beret shall be inserted in a flat style, clear polyethylene bag measuring 12 by 11 ½ inches. The unsealed opening shall be the smaller dimension of bag. Intermediate Packs: Twelve (12) berets of one size and class only shall be packed flat in an intermediate paper board box conforming to style RSC, type CF variety SW of class, domestic, grade 125 of D-5118. Box closure shall be in accordance with method II as specified in the appendix of D- 5118. Inside dimensions of box shall be 11 ½ inches in length, 11 inches in width, and 7 ½ inches in depth. Packing: Forty-eight (48) berets of one size and class only (four intermediate packs) shall packed in snug fitting fiberboard shipping container conforming to ASTM-D-5118, Type CF, Style RSC, grade 175, Variety SW, Class Domestic. This container shall have dimensions to accommodate four intermediate packs, with length of intermediate paperboard box standing. (Method of closure shall be in accordance with ASTM-D-1974, 2A2, figure 1 or as an alternate 2B6 or 2B7, figure 3.

(REF. W2444)

DELETE CURRENT "BARCODE LABEL/TAG" REQUIREMENTS AND SUBSTITUTE

THE FOLLOWING:

LABEL TAG: EACH ITEM SHALL BE INDIVIDUALLY BAR-CODED WITH A

PAPER TAG FOR PERSONAL CLOTHING ITEMS. THE PAPER USED FOR THE

TAGS SHALL BE STANDARD BLEACHED SULFATE HAVING A BASIS WEIGHT OF

100 POUNDS WITH A SMOOTH FINISH TO ACCEPT THERMAL TRANSFER AND

DIRECT PRINTING. THE TAGS SHALL HAVE A HOLE AND SHALL BE

ATTACHED TO EACH ITEM BY A FASTENER, CLEARLY LEGIBLE AND

READABLE BY SCANNER. THE BAR CODING ELEMENT SHALL BE A 13 DIGIT

NATIONAL STOCK NUMBER (NSN). THERE SHALL BE A 12 DIGIT UNIVERSAL

PRODUCT CODE (UPC) ASSIGNED FOR ALL NSNS BY THE GOVERNMENT. THE

INITIAL "UPC" MUST APPEAR BENEATH THE CODE. THE BAR CODES FOR

NSN AND UPC SHALL BE A MEDIUM TO HIGH DENSITY AND SHALL BE

LOCATED SO THAT THEY ARE COMPLETELY VISIBLE ON THE ITEM WHEN IT

IS FOLDED AND PACKAGED AS SPECIFIED. THE LABEL'S LOCATION SHALL

CAUSE NO DAMAGE TO THE ITEM.

NOTE: UNIVERSAL PRODUCT CODE INFORMATION THE GOVERMENT ASSIGNED

UNIVERSAL PRODUCT CODE (UPC) MUST BE PLACED ON ALL SHIPPING

CARTONS ON WHICH THE NSN APPEARS.

THE FOLLOWING DEFECTS APPLY FOR BARCODE LABELS/TAGS:

BAR CODE OMITTED OR NOT READABLE BY SCANNER

HUMAN-READABLE INTERPRETATION (HRI) OMITTED OR ILLEGIBLE

NOT VISIBLE ON FOLDED, PACKAGED ITEM CAUSES DAMAGE TO THE ITEM

NOTE: IF THE END ITEM IS PLACED IN A PLASTIC BAG - USE TYPE VII

(PRESSURE SENSTIVE LABEL) OF MIL-DTL-32075.

IF THE END ITEM IS TIED IN A BUNDLE OR LEFT AS AN INDIVIDUAL

ITEM, USE TYPE VIII (TAG, PAPER) OF MIL-DTL-32075.

(REF. 93546)

ADDITIONAL INFORMATION FOR COMMERCIAL AQL'S:

AQL'S FOR COMMERCIAL ITEM DESCRIPTIONS (CID'S):

VISUAL - GENERAL INSPECTION LEVEL II, AQL - 1.0

DIMENSIONAL - SPECIAL INSPECTION LEVEL S-2, AQL - 2.5

ACCEPTABILITY OF LOTS WILL BE DETERMINED BY THE USE

OF "SAMPLING PROCEDURES AND TABLES FOR INSPECTION BY

ATTRIBUTES", ANSI/ASQC Z1.4

(REF. T1921)

ADDITIONAL INFORMATION FOR A-A-52104:

A-A-52104 IS CANCELLED WITHOUT REPLACEMENT

NOTE: NOTICE 1, DTD 5/20/98, A-A-52104 IS

CANCELLED.

(REF. T1498)

A-A-52094B Thread, Cotton dated 01 May 2019 No Additional Information

(REF. T1481)

ADDITIONAL INFORMATION FOR MIL-C-43665:

INTERIM SPECIFICATION CHANGES TO MIL-C-43665C:

PAGE 2, PARA. 3.2, LINE 2, AFTER "TABLE 1 "

INSERT "OR TABLE 1A",

PAGE 3, TABLE 1, DELETE "SODIUM (4,5-DICHLORO,

2-CHLOROMETHANE SULFONAMIDO) 3',4'

6',TRICHLORO) DISHENYL ETHER (SEE 6.3.2) 0.26

0.60".

PAGE 3, AFTER TABLE 1, INSERT THE FOLLOWING NEW

TABLE:

"TABLE 1A, MOTHPROOFING COMPOUND.

. % ON WEIGHT OF WOOL

. MOTHPROOFING COMPOUND MIN. MAX.

EDOLAN ETS BEFORE DRYCLEANING

*(3-PHENOXYPHENYL) METHYL

PLUS OR MINUS CIS/TRANS 3-(2-,2-

DICCHLOROETHENYL)2,2-

DIMETHYLCYCLORPPANECARBOXYLATE. 0.058 0.40

CIS/TRANS RATIO:MAX.55% PLUS OR--AFTER DRY-CLEAN

MINUS CIS AND MIN.PLUS OR

MINUS TRANS.(*PERMETHRIN) 0.029 0.40

PAGE 3,PARA.3.4, LINE 3, AFTER "3.2" INSERT

"TABLE 1".

PAGE 3, AFTER PARA. 3.4 INSERT NEW PARAGRAPH AS

FOLLOWS:

"3.4.1 PERCENT OF MOTHPROOFING COMPOUND. THE

PERCENTAGES OF MOTHPROOFING COMPOUND SPECIFIED

IN TABLE 1A SHALL BE BASED ON WEIGHT OF PURE

COMPOUND ON THE WOOL FIBER CONTENT WHEN TESTED

BY HIGH PERFORMANCE LIQUID CHROMATOGRAPH (HPLC)

METHOD, OBTAINABLE FROM BAYER CORP., ROCK HILL,

SC 29732 (SEE 4.2.2)".

PAGE 5, PARAGRAPH 4.2.2,TABLE 11,DELETE THE

FOLLOWING:

CHARACTERISTIC REQUIREMENT TEST

. PARAGRAPH METHOD

"SODIUM (4,5-DICHLORO

2-CHLORO-METHANE

SULFONAMIDO)3',4',6',

TRICHLORO) DIPHENYL ETHER 3.4 4.3.1 3/ 4/"

AND SUBSTITUTE THE FOLLOWING:

CHARACTERISTIC REQUIREMENT TEST

. PARAGRAPH METHOD

"EDOLAN ETS

*(3-PHENOXYPHENYL 3.4.1 HPLC 7/

METHYL PLUS OR MINUS CIS/TRANS

3-(2,2-DICHLOROETHENYL)

2,2-DIMETHYL-CYCLOPROPANECARBOXYLATE

CIS/TTRANS RATIO: MAX.55%

PLUS OR MINUS CIS AND MIN.

PLUS OR MINUS TRANS.

*(PERMRTHRIN)"

PAGE 5, PARAGRAPH 4.2.2, FOR CHARACTERISTIC

EDOLAN ETS,UNDER TEST METHOD COLUMN, ADD

FOOTNOTE "7"/,ADD NEW FOOTNOTE "8"/.

PAGE 6, PARAGRAPH 4.2.2, TABLE II.AFTER FOOTNOTE

"7/",ADD THE FOLLOWING:"8"/ THE SAMPLE SHALL

BE DRY-CLEANED FOR THREE CYCLES IN ACCORDANCE

WITH AATCC TEST METHOD 86 BEFORE DETERMINING

MOTHPROOFING COMPOUND CONTENT.

PAGE 6, PARA.4.2.2, TABLE 11, AFTER FOOTNOTE 6/,

INSERT "7/ HIGH PERFORMANCE LIQUID

CHROMATOGRAPHY (HPLC) TEST METHOD MAY BE

OBTAINED FROM BAYER CORP., ROCK HILL, SC 29732."

PAGE 6, PARAGRAPHS 4.3,4.3.1,4.3.1.1,4.3.1.2,

4.3.1.3,4.3.1.4,4.3.1.5 DELETE PARAGRAPHS IN

THEIR ENTIRETY WITH NO REPLACEMENT.

PAGE 7, PARAGRAPHS 4.3.1.6, 4.3.1.7, 4.3.1.7.1

DELETE PARAGRAPHS IN THEIR ENTIRETY WITH NO

REPLACEMENT.

PAGE 8, PARAGRAPHS 4.3.1.7.2, 4.3.1.8, 4.3.1.8.1

DELETE PARAGRAPHS IN THEIR ENTIRETY WITH NO

REPLACEMENT.

PAGE 9, PARAGRAPHS 6.3 2, 6.4, 6.5, 6.6 DELETE

PARAGRAPHS IN THEIR ENTIRETY WITH NO

REPLACEMENTS.

PAGE 11, DELETE FIGURE 1 IN ITS ENTIRETY WITH NO

REPLACEMENT.

TABLE II, UNDER TEST METHOD: DELETE "2015" AND

SUBSTITUTE "2015.3"

NOTE! MITTEN FF CONC. SUPPLIED BY CIBA-GEIGY

CORP. P.O. BOX 11422, GREENSBORO, NC 27409

EDOLAN ETS, SUPPLIED BY MILES INC.,MOBAY ROAD,

PITTSBURGH,PA.15205-9741.

ARE APPROVED MOTH PROOFING AGENTS FOR

MILITARY FABRICS.

(REF. T1118)

ADDITIONAL INFORMATION FOR FED-STD-311:

INTERIM CHANGES FROM FED-STD-311:

INTERIM CHANGE FROM CH NOT 3, 01/24/75:

SECTION 4, PARA. 4.5.1.2, LINE 8: DELETE THE PERIOD AFTER

"BACKBONE" AND ADD "AND TO INDICATE THE ROOT OF THE TAIL".

INTERIM CHANGE FROM TEST METHOD 7011.1:

PARA. 4.1.2: DELETE ENTIRELY AND SUBSTITUTE THE FOLLOWING:

"4.1.2 INDICATING DEVICE. THE INDICATING DEVICE SHALL BE EITHER

OF THE KINDS LISTED BELOW.

4.1.2.1 THE SHRINKAGE METER DIAL. A DIAL INDICATOR HAVING A FACE

DIVIDED INTO 360-380 DEGREES, WITH ONE REVOLUTION OF THE DIAL

HAND CORRESPONDING TO 0.5 INCHES (12.7 MM) SPECIMEN MOVEMENT,

WITH LEEWAY FOR FOUR REVOLUTIONS.

4.1.2.2 AGD DIAL INDICATOR. A MECHANICAL DEVICE CAPABLE OF

REGISTERING ON A SCALE READING OF THE SHRINKAGE OR SWELLING

RATIO OF THE SPECIMEN IN A RATIO OF 25 UNITS OF DIAL MOVEMENT TO

ONE UNIT OF SPECIMEN MOVEMENT, OR GREATER, AND SHALL ACCURATELY

DETECT THE POINT AT WHICH SHRINKAGE BEGINS BY THE MOVEMENT OF

THE DIAL NEEDLE. THE INDICATOR SHALL HAVE A SPINDLE CAPABLE OF

ATTACHMENT TO THE SPECIMEN AND TO THE ADJUSTABLE WEIGHT ASSEMBLY

(SEE 4.1.11)."

PARA. 4.1.3: DELETE "HEATING COIL" AND INSERT "IMMERSION

HEATER".

PARA.7.1: DELETE ENTIRELY AND SUBSTITUTE THE FOLLOWING:

"7.1 THE THERMOMETERS MAY BE PURCHASED FROM THE THOMAS

SCIENTIFIC CO. OR FISHER SCIENTIFIC CO., EACH HAVING REGIONAL

OFFICES.

7.2 DIAL INDICATORS MAY BE PURCHASED FROM B. C. AMES CO.,

LEXINGTON STREET, WALTHAM, MA 02254."

(REF. T0211)

INSPECTION OF SUPPLIES SHALL BE IN ACCORDANCE WITH FAR PART

52.246-2 STANDARD INSPECTION.

ADDITIONAL INFORMATION FOR MIL-STD-105E:

MIL-STD-105E, dated 10 May 1989, is hereby canceled.

Future acquisitions may refer to: MIL-STD-1916, "DoD Preferred Methods for Acceptance of Product," or ANSI/ASQ Z1.4, "Sampling Procedures and Tables for Inspection by Attributes."

Users are cautioned to evaluate these documents for their particular application before citing it as a replacement document.

(Copies of MIL-STD-1916 are available online at http://assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)

(Copies of ANSI/ASQ Z1.4 are available online at www.asq.org or ASQ Distribution Center, 5131 S. Third Street, Milwaukee, Wisconsin 53207-6028.)

(REF. T0301)

MIL-STD-129R w/CHANGE 2 - DEPARTMENT OF DEFENSE STANDARD

PRACTICE MILITARY MARKING FOR SHIPMENT AND STORAGE

DATED: 27 SEPTEMBER 2019

INTERIM CHANGES:

OMISSION OF MARKINGS ON EXTERIOR SHIPPING CONTAINERS OF ITEMS

IN THE DLA TROOP SUPPORT CLOTHING AND TEXTILE (C&T) DIRECTORATE:

THE NOMENCLATURE AND MANUFACTURER'S NAME (WHEN THE NAME

IDENTIFIES THE MATERIAL) SHALL BE OMITTED FROM ALL EXTERIOR

SHIPPING CONTAINERS OF DLA TROOP SUPPORT C&T ITEMS, REGARDLESS

OF MODE OF SHIPMENT.

IF THE MANUFACTURER'S NAME DOES NOT IDENTIFY THE MATERIAL AS

BEING CLOTHING, IT MAY REMAIN. NSNS SHALL BE SHOWN ON ALL

SHIPPING CONTAINERS OF C&T ITEMS, THE PACKING LIST SHALL BE

PLACED INSIDE THE LAST CONTAINER TO BE LOADED FOR EACH SHIPMENT.

THE WORDS "PACKING LIST HERE" SHALL BE STENCILED, NOT HAND

LETTERED, ON THE CONTAINER.

(REF. T0303)

MIL-STD-147E w/CHANGE 2

27 JUNE 2019

DEPARTMENT OF DEFENSE

STANDARD PRACTICE

PALLETIZED UNIT LOADS

(REF.