Atch 2 201754322-37.pdf

AL 6061-T6WIRE PASS THROUGH COVER, CONSOLIDATED STACK201754322-3798752

PARTS LIST

MATERIAL/SPECIFICATIONDESCRIPTIONPART NUMBERCAGEC

98752D 201754322-37 0.02

UNLESS OTHERWISE SPECIFIED

DIMENSIONS ARE IN INCHES-TOLERANCES ON:

FRACTIONS DECIMALS ANGLES

± 1/32 .X ± .100

.XX ± .030

.XXX ± .010

± 2°

THIRD ANGLE PROJECTION

DRAFTER

CHECKER

PROJECT ENGINEER

ENGINEERING APPROVAL

A.F. AUTHENTICATION

RELEASE

J.GILLMOR

T.PRICE

T.PRICE

B.BINGHAM

E.MULLINAX

K.SIMPSON

516 MXDPAF

516 MXDPAF

516 MXDPAF

516 MXDPAF

AFLCMC/WNAEA

AFLCMC/WNAE

DATE

3/17/2025

3/17/2025

3/17/2025

3/17/2025

U.S. AIR FORCE

TITLE

WIRE PASS THROUGH COVER,

CONSOLIDATED STACK

SIZE CAGE CODE DWG NO. REV

SCALE WEIGHT SHEET

3:1 0.117 LBS 1 OF 3

INVENTOR

CAD PROG: VER:

COMPUTER DRAWING

FILE NAME:

201754322-37.idw

UNLESS OTHERWISE INDICATED:

-DRAWING WAS PREPARED IN ACCORDANCE

WITH ASME 14.100, APPX. B THRU. E

-INTERPRET DRAWINGS IN ACCORDANCE WITH

ASME Y14.5-2009

-REMOVE BURRS AND BREAK SHARP EDGES

DESIGNED FOR:

ATS PROGRAM OFFICE

NEXT ASSY

201754322-30 2020109112-10

USED ON

APPLICATION

A A

B B

C C

D D

REVISION HISTORY

REV DESCRIPTION DATE APPROVED

0.02 INITIAL RELEASE 3/17/2025 B.BINGHAM

NOTES:

FINISH: EXCEPT WHERE SPECIFIED.

A. CHEM FILM PER MIL-DTL-5541, TYPE 1, CLASS 3

B. PRIME EXTERIOR ONLY WITH EPOXY PRIME PER MIL-DTL-53022, TYPE IV EXCEPT ON NOTED AREAS.

C. PAINT EXTERIOR ONLY WITH WHITE POLYURETHANE COATING PER MIL-PRF-85285, TYPE II, CLASS H COLOR # 17925 OF FED-STD-595.

1. IDENTIFY PART IN ACCORDANCE WITH MIL-STD-130. BAG AND TAG ALL ITEMS TOO SMALL TO IDENTIFY.

2. MASK FROM PRIMER AND PAINT.

3. ALL FABRICATION TO CONFORM TO MIL-HDBK-454 & MIL-STD-108.

4. AFTER FABRICATION, PARTS AND ASSEMBLED EQUIPMENT SHALL BE CLEANED OF SMUDGES; LOOSE, SPATTERED, OR EXCESS SOLDER; WELD METAL; METAL CHIPS AND MOLD

RELEASE AGENTS; OR ANY OTHER FOREIGN MATERIAL WHICH MIGHT DETRACT FROM THE INTENDED OPERATION, FUNCTION, OR APPEARANCE OF THE EQUIPMENT.

5. FOR DIMENSIONS NOT SHOWN REFER TO CAD DATA.

6. CAD DATA IS BASIC UNLESS OTHERWISE SPECIFIED 0.030.

PRELIMINARY

3/17/2025

DISTRIBUTION STATEMENT D

DESTRUCTION NOTICE

WARNING

DISTRIBUTION AUTHORIZED TO DOD AND U.S. DOD CONTRACTORS ONLY

FOR ADMINISTRATIVE OR OPERATIONAL USE. DATE OF DETERMINATION

IS . OTHER REQUESTS FOR THIS DOCUMENT SHALL BE REFERRED TO THE

ATS PROGRAM OFFICE AFLCMC/WNA-ATS ROBINS A.F.B GA. 31098.

QUESTIONS CONCERNING TECHNICAL CONTENT SHALL BE REFERRED TO

309 SWEG/516 SWES/MXDPAF HILL A.F.B. UT. 84056

DESTROY BY ANY METHOD THAT WILL PREVENT DISCLOSURE OF

CONTENTS OR RECONSTRUCTION OF THE DOCUMENTS.

EXPORT CONTROLLED. THIS DOCUMENT CONTAINS TECHNICAL

DATA WHOSE EXPORT IS RESTRICTED BY THE ARMS EXPORT

CONTROL ACT (TITLE 22, U.S.C.2751 ET SEQ.) OR THE EXPORT

ADMINISTRATION ACT OF 1979, AS AMENDED, TITLE 50, U.S.C.,APP.

2401 ET SEQ. VIOLATION OF THESE EXPORT-CONTROL LAWS IS

SUBJECT TO SEVERE CRIMINAL PENALTIES. DISSEMINATION OF

THIS DOCUMENT IS CONTROLLED UNDER DoD DIRECTIVE 5230.25.

ALL SHEETS ARE THE

SAME REVISION STATUS

-37 WIRE PASS THROUGH COVER

TOP ISOMETRIC

SCALE 3 : 1

BOTTOM ISOMETRIC

SECTION A-A

SECTION B-B

TOP ISOMETRIC

A

A

B B

SIZE

DWG NO REV

SCALE

SHEET

OF

CAGE CODE

98752

D

0.02

201754322-37

J.GILLMOR

DRAWN:

CHECKED:

T.PRICE

3:1

A A

B B

C C

D D

.750

1.3751.375

1.250

3.000

6X .125

.001

.004+

THRU

.250 X 82°

R.0304X WIRE EDGE SMOOTHING

(R.125)

1.00

(.625)

1.000

.000

.015+

(.500)

.125

.015

.000+

2X

.375

B

C

A

.375

R.1254X

.005 A B C

D

.000 A B

.005 A B

.250 1.00 TO CAVITY

.004

.9375.010

.375 BETWEEN RADIAL CUTS

.000 B

.000 B

1.75

.250

.1252X FULL RADIAL CUTS

.250

(.1875)

TOP ISOMETRIC

SCALE 3 : 1

-37 MASK SHADED AREAS

SIZE

DWG NO REV

SCALE

SHEET

OF

CAGE CODE

98752

D

0.02

201754322-37

J.GILLMOR

DRAWN:

CHECKED:

T.PRICE

3:1

A A

B B

C C

D D