Appendix B.pdf

PLAYGROUND INSTALLATION

U.S. ARMY CORPS OF ENGINEERS

EDWARD MACDOWELL LAKE

PETERBOROUGH, NEW HAMPSHIRE

STATEMENT OF WORK

Appendix B

See Attached

Playground Diagrams

Playground Installation Instructions

Swing Set Diagram

Swing Set Installation Instructions

Capacity: 50Age Group: 5-12

Weight: 1,350Fall Height: 7’

FunPlay Structure Layout STR-353259

CAT # STR-353259-G

677.0 Approximate Square Feet

Actual Size: 15’-4” x 23’-2”

Actual Use Zone: 27’-4” x 35’-2”

DRAWN

CHECKED

SCALE

PC PRIMER

CONTROLLED

DOCUMENT

X

DATE

DATE

SHEET 1 OF 1

USAGE REV DATE

STR-353259-HL

2/25/2026

TITLE

PART NO

HOLE LAYOUT

Company Confidential

This design configuration is the property of this firm and may not be reproduced or used in any manner without the expressed written consent of LP Industries and Childforms

2/25/2026

POWDER COAT

N/A N/A

MA

STR-353259

TOLERANCES PER ASME Y14.5.

UNLESS OTHERWISE SPECIFIED

STANDARD TOLERANCES

= `2~

.X = `.1

X/X = `1/16

.XXX = `.062

.XX = `.06

INTERPRET DIMENSIONS AND

DIMENSIONS ARE IN INCHES.

REV ECO DATE BY APVD

REVISION

HOLE SIZE

HOLE DIAMETER DEPTH

A 18" 24"

B 12" 18"

POLE HEIGHT

POLE HEIGHT

1 14'

2 11'

Listed footer sizes are general recommendations.

Consult your local building codes for specifics for your locations.

.0

46.5

33.4

13.4

25.5

55.0

41.3

5.3

62.6

126.5

27.1

19.1

211.9

107.7 71.6

36.0 .0

31.6

4.1

29.2 6.5

47.2

56.9

26.2 10.2

B

B

B

B B

B

B

BB

B B

A2

A1 A1

A1

A1

A2

A2

A2

A2 A2

I-3.5INADATRANSWSTEPINSTrevA Page 1 of 6

Childforms® FunPlay™ I-3.5INADATRANSWSTEPINST

ADA Transfer Staircase Assembly Instructions:

Please read and follow all Safety Information.

Please review assembly and component Diagrams.

Verify component & hardware quantities received.

Familiarize yourself with the installation procedures.

Safety

Please follow assembly procedure in the correct order.

Play site ground material should only be of an approved, shock-absorbing type and meet minimum depth requirements. NEVER install playground equipment over paved or hard surfaces.

Please be sure that all fasteners are used in the proper location.

Be sure that minimum fall zone requirements are met.

Do not allow children to play on or near equipment which is in need or repair or replacement, is incomplete or is otherwise considered unsafe.

1) Parts Inventory and Set-Up Confirm that all components, hardware and special tools are included (see Parts List).

Gather any additional tools necessary for installation (hex driver, level, tape measure, etc). Please follow diagrams and instructions in order.

2) Site location and Preparation Be sure site is of adequate size- allow for minimum fall zones.

Be sure site is graded, level and free of debris for proper set-up and assembly.

Measure and mark site to determine structure module location and orientation.

3) Assembly- General Please use correct type and length fasteners as shown in the installation procedure.

Before setting Play Structure modules in place, verify all hardware has been tightened.

Be sure to follow the assembly order to ease the construction procedure.

I-3.5INADATRANSWSTEPINSTrevA Page 2 of 6

PARTS LIST

Item Qty. Description Drawing Part Number

A1 36” ADA Stairs 900-00032

A2 48” ADA Stairs 900-00038

1ea of (A1) for 36" Tall Decks 1ea of (A2) for 48" Tall Decks

B (2) 36” ADA Handrail 900-00035

OR

B (2) 48” ADA Handrail 900-00039

C (1) Transfer Deck w Step 900-00047-01

D (2) Access Step Handrail 900-00094

E (2) 3.5” Handrail Mounting Clamp 935-127-0004-B/G

F (2) Handrail Spacer 900-00039-05

I-3.5INADATRANSWSTEPINSTrevA Page 3 of 6

Hardware Components: 0-3.5INADATRANSWSTEPINST Item Qty. Description Drawing Part Number

HA (6) 3/8 Neoprene Washer 100-38WSSNP

HB (2) SS Flat Washer 3/8" ID x 3/4" OD 100-38WSP

HB2 (24) Flat Washer 1”x.4”x.07” 100-815FW

HC (8) 5/16-18 x 1 SS Torx Truss Head Bolt 100-5161

HD (4) 5/16-18 x 1-3/4 SS Torx Truss Head Bolt 100-516134

HF (14) 5/16” Stainless Nylon Lock Nut 100-516NLNSS

HG (2) 5/16-18 x 1-1/4 SS Torx Truss Head Bolt 100-516114

HH (2) ¼” Hammer Drive Pin x1-1/2” 100-14HDP

HI (2) 5/16-18 x 2-3/4 SS Torx Truss Head Bolt 100-516234

Tools:

TB (1) Torx T-40 Driver Bit 100-00T40

I-3.5INADATRANSWSTEPINSTrevA Page 4 of 6

Installation Instructions

1) Mount Staircase to Structure by taking the Staircase (A1 or A2) and mounting it to the

Structure Deck using (4) 5/16-18 x 1 SS Truss Head Bolt (HC), (8) Flat Washer 1” x.4” x .07” (HB2), and (4) 5/16-18 Nylon Lock Nuts SS (HF). Be sure to prop the bottom of staircase with appropriately sized boards. (See Figure).

2) Take the handrail (B) and place (1) handrail spacer (H) between tab on the handrail leg and staircase and secure to staircase using (2) 5/16-18 x 1-3/4 SS Truss Head Bolt (HD),

(2) Flat Washer 1” (HB2), (2) 5/16 Neoprene Washers (HA), and (2) 5/16-18 Nylon Lock Nuts SS (HF) per handrail.

3) Loosely mount the Clamp to support pole that the handrails will be mounting to.

(See Figure). Note: The drive pin in the clamp should be facing down.

HF

HB2

HB2

HC

HA

HB2

HF

HF

HA

HD

HD

I-3.5INADATRANSWSTEPINSTrevA Page 5 of 6

4) Slide Mounting Bracket into clamp and then mount the bracket to the back end (threaded insert) of the handrail using (1) 5/16-18 x 1-1/4 SS Truss Head Bolt (HG) and (1) SS Flat Washer 3/8" ID x 3/4" OD (HB) per handrail. Once handrail is at desired height tighten the clamp fully to the pole.

5) Review structure spec sheet to determine the orientation of the transfer deck step.

Attach the Access Step Handrail (D) to the transfer deck (C) with (2) 5/16-18 x 2.75” Bolt (HI), (2) 3/8 Neoprene Washer (HA), (2) Flat Washer 1” x.4” x.07” (HB2), and (2) 5/16-18 Nylon Lock Nuts SS (HF).

6) When mounting Transfer deck (C) to Staircase place access step handrail (D) into anchor holes and mount deck using (4) 5/16-18 x 1 SS Truss Head Bolt (HC), (8) Flat Washer 1” x.4” x .07” (HB2), and (4) 5/16-18 Nylon Lock Nuts SS (HF). Be sure to prop the bottom of entrance deck with appropriately sized boards. (See Figure).

HF

HA

HB2

HI

D

I-3.5INADATRANSWSTEPINSTrevA Page 6 of 6

7) When complete, plum and level; drill a 1/4” hole into clamp sides and into the upright post posts. Use dimple on clamp as drill guide. Insert the 1-1/2” drive pin (HH) into the freshly drilled hole and then tap it until pin is flush with clamp.

REV ECO DATE BY APRV

A 4-18-2012 MA DAH

B 5/24/2013 MA

C 6/5/2019 MA

I-3.5INALPINECLMINSTrevBB Page 1 of 4

Childforms® FunPlay™ I-3.5INALPINECLMINST

Climbing Wall Assembly Mounting:

NOTE:

This assembly is not a stand alone structure, and must be connected to solidly build structure.

Please refer to guidelines as specified by the CPSC and ASTM F1487 Please review assembly and component Diagrams.

Verify component & hardware quantities received.

Familiarize yourself with the installation procedures.

1) Parts Inventory and Set-Up Confirm that all components, hardware and special tools are included (see Parts List).

Gather any additional tools necessary for installation. Please follow diagrams and instructions in order.

2) Assembly- General Please use correct type and length fasteners included in the hardware kit for this assembly. Be sure to follow the assembly order to ease the construction procedure.

Start all screws before tightening them.

I-3.5INALPINECLMINSTrevBB Page 2 of 4

Assembly Components:

Item Qty. Description Drawing Part Number

A (1) Climbing Wall Base 935-281-0014

B (1) Arch Entrance 935-281-0013

C (6) 3.5” Panel Bolt Clamp 935-127-0003-B/G

Hardware Components: 0-3.5INALPINECLMHWKIT Item Qty. Description Drawing Part Number

HA (10) 5/16-18 x 1-1/2 SS Torx Bolt 100-516112

HB (14) Flat Washer 100-815FWSS

HC (10) 5/16-18 Nylock Nut 100-516NLN

HF (6) ¼” Hammer Drive Pin 100-14HDP

Tools: (SUPPLIED IN INSTALLERS HW KIT) Item Qty. Description Drawing Part Number

TA (1) Torx Driver Bit - T40 100-00T40

TB (1) Tee Nut Wrench 100-TNUTW

I-3.5INALPINECLMINSTrevBB Page 3 of 4

Installation procedure:

1) Loosely mount (4) clamps (2 per pole) below the deck to the poles that the

Climbing Wall is designated to mount to.

2) Bolt Clamp to panel back of the climbing wall base using (1) 5/16-18 x 1-1/2 SS Torx Bolt (HA), (1) Flat Washer(HB), and (1) 5/16-18 Nylock Nut(HC) per clamp. Then loosely bolt the top of the climbing wall base to the deck using only the two middle slots and bolting with (2) 5/16-18 x 1-1/2 SS Torx Bolt (HA), (4) Flat Washer(HB), and (2) 5/16-18 Nylock Nut(HC).

3) Loosely mount (2) clamps (1 per pole) above the deck to the poles that the Climbing Wall is designated to mount to.

I-3.5INALPINECLMINSTrevBB Page 4 of 4

4) Slide the Arch Entrance into the top of the Climbing Wall Base at the deck and loosely bolt the bottom of the Arch Entrance and the Climbing Wall Base to the deck in the remaining slots with (2) 5/16-18 x 1-1/2 SS Bolt(HA), (4) Flat Washers(HB), and (2) 5/16-18 Nylock Nut(HC). Then bolt the clamps to panel back of the Arch Entrance using (1) 5/16-18 x 1-1/2 SS Torx Bolt(HA), (1) Flat Washer(HB), and (1) 5/16-18 Nylock Nut(HC) per clamp.

5) Level and adjust all clamps as needed and then tighten around poles and tighten to panel. Drill and drive pin each clamp. (1) Drive Pin/Clamp(HF)

REV ECO DATE BY APRV

A 10-0002 3-5-10 RP DHZ

B 5/30/14 MA DH

I-3.5INCLAMPINSTrevA Page 1of 2

Childforms® FunPlay™ I-3.5INCLAMPINST

3.5” Clamp Assemblies:

935-127-0001 935-127-0003 935-127-0005 Pole Mount Panel Ear Mount Deck Mount

Assembly- General

Be sure to follow the assembly order to ease the construction procedure. Start all screws before tightening them.

PARTS LIST

Assembly Components:

Item Qty. Description Drawing Part Number

A (1) 3.5” Pole Clamp Half 935-128-0002-B/G

B (1) 3.5” Blank Clamp Half 935-128-0001-B/G

C (1) 3.5” Panel Ear Clamp Half 935-128-0004-B/G

D (1) 3.5” Deck Clamp Half 935-128-0003-B/G

E (2) 5/16-18 x 1 SS Torx Head Bolt 100-5161

F (2) 5/16-18 Nylon Lock Nuts SS 100-516NLNSS

G (1) Hammer Drive Pin 1/4" 100-14HDP (included in there respecting hardware kits)

I-3.5INCLAMPINSTrevA Page 2of 2

1. When assembling the clamp to the pole take the blank clamp half and the appropriate clamp half and place them around the pole. Then take (2) 5/16-18 x 1 SS Torx Head Bolt

(E) and (2) 5/16-18 Nylon Lock Nuts SS (F) and loosely bolt clamp to pole. Move Clamp to desired height and then tighten bolts which will cause the clamp to tighten to pole.

(Note: Clamp has a recessed hex pocket used as wrench for holding nuts)

2. When the clamp is being used as a load bearing clamp (i.e. decking, horizontal ladder etc.) the clamp must have two 1/4” holes drilled through the clamp and into the pole.

There is a divot in clamp to be used as drill starting point. Insert 1/4” drive pin (G) through the newly drilled hole and into the support tube. Tap pin until flush with clamp.

Repeat this process on the opposite side.

A --- 11-9-11 RP DHZ

I-3.5INDBLSSLDINSTrevGG Page 1of 4

Childforms® FunPlay™ I-3.5INDBLSSLDINST

Double Straight Slide Assembly: 36” or 48” high

NOTE:

This assembly is not a stand alone structure, and must be connected to solidly build structure.

Please refer to guidelines as specified by the CPSC and ASTM F1487

Please review assembly and component Diagrams.

Verify component & hardware quantities received.

Familiarize yourself with the installation procedures.

1) Parts Inventory and Set-Up Confirm that all components, hardware and special tools are included (see Parts List).

Gather any additional tools necessary for installation . Please follow diagrams and instructions in order.

2) Assembly- General Please use correct type and length fasteners included in the hardware kit for this assembly. Be sure to follow the assembly order to ease the construction procedure. Start all screws before tightening them.

I-3.5INDBLSSLDINSTrevGG Page 2of 4

Assembly Components:

Item Qty. Description Drawing Part Number

A (1) Double Straight Slide (48”) 950-351-0015

OR

A (1) Double Straight Slide(36”) 935-351-0014

B (1) Hood Panel 935-351-0004

C (2) Slide Anchor 935-351-0016-W

D (4) Panel Mount Clamps 935-127-0003-B/G

Hardware Components: 0-3.5IN48DBLSSLDHWKITrevG Item Qty. Description Drawing Part Number

HA (4) 3/8 x 1 Torx Button Head Screws 100-381

HB (16) SS Flat Washer 100-815FWSS

HC (12) 3/8 Split Washer 100-38SW

HD (4) 5/16-18 x 1 1/2 SS Torx Bolt 100-516112

HF (4) 5/16-18 Nylock Nut 100-516NLNSS

HG (8) 3/8 x 3/4 Torx Button Head Screws 100-3834

I-3.5INDBLSSLDINSTrevGG Page 3of 4

Tools: (Supplied in the Installer’s Hardware Kit) Item Qty. Description Drawing Part Number

TA (1) Socket Driver Bit T-45 100-00T45

TC (1) Socket Driver Bit T-40 100-00T40

Installation procedure:

1) Lay Slide (A) on side and attach Anchor (C) to the bottom of slide using (4) 3/8 x 3/4 Screw(HG), (4) 3/8 SS Flat Washer(HB), and (4) 3/8 Split Washer(HC) per anchor.

2) Place Anchors into the footing holes and place Slide up to Decking.

3) Attach Slide to Decking with (4) 3/8 x 1 Torx Button Head Screws(HA), (4) 3/8 SS Flat Washer(HB), and (4) 3/8 Split Washer(HC).

4) Loosely mount the clamps to the poles that the panel is designated to mount to (Ref Clamp Assembly Manual).

I-3.5INDBLSSLDINSTrevGG Page 4of 4

5) Bolt Clamp to panel face using (4) 5/16-18 x 1-1/2 SS Torx Bolt(HD),

(4) Flat Washer(HB), and (4) 5/16-18 Nylock Nut(HF).

6) Level and adjust all clamps as needed so that Slide Hood sits approximately 21” above the deck and then tighten around poles and tighten to panel.

B 11-01-2012 MA DAH

I-3.5INDECKINSTrevA.doc Page 1 of 7

Childforms® FunPlay™ I-3.5INDECKINST

Square Decking & Triangle Decking Assembly:

935-551-0001 935-551-0002 935-551-0003

935-551-0006 935-551-0005

NOTE:

This assembly is not a stand alone structure, and must be connected to solidly build structure.

Please refer to guidelines as specified by the CPSC and ASTM F1487 Please review assembly and component Diagrams.

Verify component & hardware quantities received.

Familiarize yourself with the installation procedures.

1) Parts Inventory and Set-Up Confirm that all components, hardware and special tools are included (see Parts List).

Gather any additional tools necessary for installation (hex driver, level, tape measure, etc). Please follow diagrams and instructions in order.

2) Site location and Preparation Be sure site is of adequate size- allow for minimum fall zones (see Layout Diagram).

Be sure site is graded, level and free of debris for proper set-up and assembly..

Measure and mark site to determine structure location and orientation.

I-3.5INDECKINSTrevA.doc Page 2 of 7

3) Assembly- General Please use correct type and length fasteners as shown in the installation procedure.

Before setting Play Structure modules in place, verify all hardware has been tightened.

Be sure to follow the assembly order to ease the construction procedure.

4) Installation Procedure After measurement and layout of site, carefully measure for ground anchor locations.

Confirm footer locations- dig, pour and set footers, locating one module at a time.

Be sure Play Structure remains level and square to previous modules before continuing.

PARTS LIST

Assembly Components:

Item Qty. Description Drawing Part Number

A (1) Square Deck 935-550-0001

A (1) Triangle Deck 935-550-0002

A (1) Half Hexagon Decking 935-550-0003

A (1) Rectangle Deck 950-550-0004

A (1) Trapezoid Deck 935-550-0005

I-3.5INDECKINSTrevA.doc Page 3 of 7

B (4)/(3)/(5) 3.5” Base Pole 935-575-0001-B/G OR 935-575-0002-B/G Note: 14’ poles are used with decks with a roof over it. 14’ length is to accommodate a deck 4’ above the surfacing. If installing a roof over a deck 3’ above surfacing, poles can be cut off at footer end to accommodate lower deck height. (See SPEC Sheet for deck heights) Roof must be a minimum of 84” above the deck per ASTM f1487-11.

C (4)/(3)/(5) Mounting Clamp 935-127-0004-B/G

Hardware Components:

0-3.5INSQDECKHWKIT* 0-3.5INTRIDECKHWKIT*0-3.5INHEXDECKHWKIT

Item Qty. Description Drawing Part Number

HA (4) / (3) / (5) 5/16-18 x 2-1/4 Button Head 100-516214

HB (4) / (3) / (5) 5/16-18 Nylon Lock Nuts SS 100-516NLNSS

HC (4) / (3) / (5) Flat Washer 1”x.4”x.07” 100-815FWSS

HD (8)/(6)/(10) ¼” Hammer Drive Pin x1-1/2” 100-14HDP

Tools: (SUPPLIED IN INSTALLERS HW KIT) Item Qty. Description Drawing Part Number

TA (1) Torx T-40 Driver Bit 100-00T40

Installation procedure:

1) Begin with Base Poles (B) planted into the ground (See Footing Diagram). Install

Mounting Clamps (C) at desired height (See Clamp Assembly Instructions). Note:

Subtract deck thickness when placing clamps. (See Figure).

Installation Tip: Start with the roof covered deck.[Follow SPEC sheet for deck heights] For 48” deck heights (TYPICAL) Measure 84.5" down from the Top end of the 3.5" pipe that will be facing up. Make a line on the tube at the 84.5"inch mark. Do this to 4 tubes.

Mount and tighten the deck clamps to the 4 poles just below the 84.5 mark. This sets the deck height and lets you level while standing on the ground.

I-3.5INDECKINSTrevA.doc Page 4 of 7

Using the clamps as leveling points. Set the pole height 48" plus the surfacing depth.

I.e. 12" of surfacing + 48" deck height = 60" (Follow your SPEC sheet for deck heights)

Put a tie down strap around the three or four poles or 5 poles and tighten. This will pull the poles in tight to the decks; this also helps to stabilize while pouring the cement and assures correct widths for the panels. See next step 3 before adding cement.

2) Situate the Deck (A) onto the clamps inside the base poles and mount to clamps using (1) 5/16-18 x 2-1/4 Button Head (HA), (1) Flat Washer 1”x.4”x.07” (HC), and

(1) 5/16-18 Nylon Lock Nuts (HB). (See Figure).

3) When complete, plum and level; drill a 1/4” hole into clamp sides and into the upright post posts. Use dimple on clamp as drill guide. Insert the 1-1/2” drive pin (HD) into the freshly drilled hole and then tap it until pin is flush with clamp. (Do this to both sides of the clamp)

HA

HC

HB

I-3.5INDECKINSTrevA.doc Page 5 of 7

Installation procedure for two Decks Together:

Hardware Components: O-3.5INDECKTODECKHWKIT Item Qty. Description Drawing Part Number

HE (4) 5/16-18 x 1 SS Truss Head Bolt 100-5161

HF (8) Flat Washer 1”x.4”x.07” 100-815FWSS HG (4) 5/16-18 Nylon Lock Nuts SS 100-516NLNSS

Installation procedure:

1) Mount Decks by taking the loose Deck (Desk A) and mounting it to the Structure Deck (Deck B) using (4) 5/16-18 x 1 SS Truss Head Bolt (HE), (8) Flat Washer 1”x.4”x.07” (HF), and (4) 5/16-18 Nylon Lock Nuts SS (HG). (See Figure).

Installation Tip: Use temporary prop to hold subsequent decks level and then set poles and clamps for the deck.

I-3.5INDECKINSTrevA.doc Page 6 of 7

Installation procedure for two half hexagon decks together:

Hardware Components: (2x) 0-DECKTODECKHWKIT Item Qty. Description Drawing Part Number

HE (8) 5/16-18 x 1 SS Truss Head Bolt 100-5161 HF (16) SS Flat Washer 3/8" ID x 1" OD 100-815FWSS

HG (8) 5/16-18 Nylon Lock Nuts SS 100-516NLNSS

Installation procedure:

1) Mount Decks by taking the loose Deck (Deck A) and mounting it to the Structure Deck (Deck B) using (4) 5/16-18 x 1 SS Truss Head Bolt (HE), (8) SS Flat Washer 3/8" ID x 1" OD (HF), and (4) 5/16-18 Nylon Lock Nuts SS (HG). (See Figure).

NOTE: Center support pole will have (2) deck mounting clamp halves when (2) half hexagon decks are to be at the same height.

Installation Tip: Use temporary prop to hold subsequent decks level and then set poles and clamps for the deck.

I-3.5INDECKINSTrevA.doc Page 7 of 7

A 12-05-2012 DAH DHZ

B 10-23-2018 DAH DHZ

I-3.5INHORIZLADINSTrevB Page 1 of 5

Childforms® FunPlay™ I-HORIZLADINSTR

Horizontal Ladder Assembly:

Please refer to guidelines as specified by the CPSC and ASTM F1487 Please review assembly and component Diagrams.

Verify component & hardware quantities received.

Familiarize yourself with the installation procedures.

1) Parts Inventory and Set-Up Confirm that all components, hardware and special tools are included (see Parts List).

Gather any additional tools necessary for installation (hex driver, level, tape measure, drill, ¼” drill bit). Please follow diagrams and instructions in order.

2) Site location and Preparation Be sure site is of adequate size- allow for minimum fall zones (see Layout Diagram).

Be sure site is graded, level and free of debris for proper set-up and assembly.

Measure and mark site to determine structure location and orientation.

3) Assembly- General Please use correct type and length fasteners as shown in the installation procedure.

Before setting Play Structure modules in place, verify all hardware has been tightened.

Be sure to follow the assembly order to ease the construction procedure.

PARTS LIST

Assembly Components:

Item Qty. Description Drawing Part Number

A (1) Straight Horizontal Ladder 935-281-0008-Color

A (1) Octagon Horizontal Ladder 935-281-0011-Color

A (1) Lower Loop Horizontal Ladder 935-281-0009-Color

I-3.5INHORIZLADINSTrevB Page 2 of 5

A (1) Loop Horizontal Ladder 935-281-0010-Color

B (4) 3.5” Panel Tube Mounting Clamp 935-127-0001-B/G

(8) 5/16-18 x 1-1/4 SS Torx Bolt 100-516114 (In Clamp HW bag)

(8) 5/16-18 Nylock Nut 100-516NLN (In Clamp HW bag)

Hardware Components: 0-3.5INHORIZLDRHWKIT Item Qty. Description Drawing Part Number

HA (4) ¼” Hammer Drive Pin x 3/4” 100-14HDP34

HB (8) ¼” Hammer Drive Pin x1-1/2” 100-14HDP

OVHD Access Ladder

Assembly Components:

Item Qty. Description Drawing Part Number

C (1) OVHD Access Ladder 935-281-0006-Color

D (2) 3.5” Panel Tube Mounting Clamp 935-127-0001

(4) 5/16-18 x 1-1/4 SS Torx Bolt 100-516114 (In Clamp HW bag)

(4) 5/16-18 Nylock Nut 100-516NLN (In Clamp HW bag)

I-3.5INHORIZLADINSTrevB Page 3 of 5

Hardware Components: 0-3.5INOVHDACSLDRHWKIT Item Qty. Description Drawing Part Number

HA (2) ¼” Hammer Drive Pin x 3/4” 100-14HDP34

HB (2) ¼” Hammer Drive Pin x1-1/2” 100-14HDP

Installation procedure:

1) Place Panel Mount Clamp Half (Ref Clamp Assembly Manual) onto the ends of the

Horizontal Ladder (A), (See Figure).

2) To mount the Horizontal Ladder (A) to support pole raise ladder to appropriate height above surfacing in accordance with ASTM 1487 standards. Check for level and plumbness. Place Blank Clamp Half onto pole to match the Panel Mount Clamp Half and secure. (See Figure).

3) Dig two holes 18” deep and with 12” diameters centered with the support posts for vertical access ladder (C). Use figure to mark the centers for each hole.

A

C

C

I-3.5INHORIZLADINSTrevB Page 4 of 5

4) Place Panel Mount Clamp Half (Ref Clamp Assembly Manual) onto the ends of the Vertical Access Ladder (C), (See Figure).

5) To mount the Vertical Access Ladder (C) to support pole raise ladder no greater than 36” above the surface to the highest rung of ladder while keeping the bottom of ladder below the protective surfacing level (see figure below). Check for level and plumbness. Place Blank Clamp Half onto pole to match the Panel Mount Clamp Half and secure. (See Figure).

6) When complete, plum and level; drill a 1/4” hole into clamp sides and into the upright posts. Use dimple on clamp as drill guide. Insert the 1-1/2” drive pin (HB) into the freshly drilled hole and then tap it until pin is flush with clamp.

I-3.5INHORIZLADINSTrevB Page 5 of 5

7) Take the 3/4” drive pins (HA) and drill a 1/4” hole into the top of each clamp ear 3/8” from the outside end and into the railing that is being held. Once drive pin is in place then tap drive pin flush with the clamp ear.

REV ECO DATE BY

APRV

B 13-005 3/12/2013 MA DH

I-3.5INPNLINSTrevA Page 1of 4

Childforms® FunPlay™ I-3.5INPNLINST

Panel Assembly Mounting:

NOTE:

This assembly is not a stand alone structure, and must be connected to solidly build structure.

Please refer to guidelines as specified by the CPSC and ASTM F1487 Please review assembly and component Diagrams.

Verify component & hardware quantities received.

Familiarize yourself with the installation procedures.

1) Parts Inventory and Set-Up Confirm that all components, hardware and special tools are included (see Parts List).

Gather any additional tools necessary for installation. Please follow diagrams and instructions in order.

2) Assembly- General Please use correct type and length fasteners included in the hardware kit for this assembly. Be sure to follow the assembly order to ease the construction procedure.

Start all screws before tightening them.

PARTS LIST

Assembly Components:

Item Qty. Description Drawing Part Number

A (1) Panel OR 180-##### OR 181-#####

B (4) 3.5” Panel Bolt Clamp 935-127-0003

I-3.5INPNLINSTrevA Page 2of 4

Hardware Components: (0-3.5INPNLHWKIT) Item Qty. Description Drawing Part Number

HA (4) 5/16-18 x 1-1/2 SS Torx Bolt 100-516112

HB (4) Flat Washer 1"x.4"x.07" 100-815FWSS

HC (4) 5/16-18 Nylock Nut 100-516NLN

Tools: (SUPPLIED IN INSTALLERS HW KIT) Item Qty. Description Drawing Part Number

TA (1) Torx Driver Bit - T40 100-00T40

Installation procedure:

1) Loosely mount the clamps to the poles that the panel is designated to mount to.

2) Bolt Clamp to panel face using (4) 5/16-18 x 1-1/2 SS Torx Bolt (HA), (4) Flat Washer 1"x.4"x.07" (HB), and (4) 5/16-18 Nylock Nut (HC).

3) Level and adjust all clamps as needed and then tighten around poles and tighten to panel.

Panel Table Assembly Mounting:

I-3.5INPNLINSTrevA Page 3of 4

180-13000

After following the steps from above by mounting the panel base to the poles move to next step.

PARTS LIST

Assembly Components:

Item Qty. Description Drawing Part Number

C (1) Base Panel 180-13001

D (4) Table Top 180-13002

Hardware Components: (0-3.5PNLTBLHWKIT) Item Qty. Description Drawing Part Number

HD (4) 5/16-18 x 3/4 SS Torx Head Bolt 100-51634

HE (2) 5/16-18 x 1 SS Torx Head Bolt 100-5161

HF (6) 5/16-18 T-Nut SS 100-516TNS

HG (4) SS L-Bracket 100-LBRKTSS

I-3.5INPNLINSTrevA Page 4of 4

Tools: (SUPPLIED IN INSTALLERS HW KIT) Item Qty. Description Drawing Part Number

TA (1) Tee Nut Wrench 100-TNUTW

Installation procedure:

1) Take the Shelf (D) and attach loosely (4) L-Brackets (HG) to the bottom of the shelf with longer end attaching to shelf using (1) 5/16-18 x 3/4 Torx Head Bolt (HD) and (1) 5/16-18 T-Nut SS (HF) per bracket. (As Shown)

2) Slide the shelf onto the base sandwiching the base between the L-brackets. Attach the shelf using (2) 5/16-18 x 1 Torx Head Bolt (HE) and (2) 5/16-18 T-Nut SS (HF). (As Shown)

3) Follow Steps 1-3 from panel assembly above to mount to poles.

A 11-09-2012 DAH

I-3.5INRISERINSTrevA Page 1of 3

Childforms® FunPlay™ I-3.5INRISERINSTrevA

6”, 12” & 24” Riser Assembly:

NOTE:

This assembly is not a stand alone structure, and must be connected to solidly build structure.

Please refer to guidelines as specified by the CPSC and ASTM F1487 Please review assembly and component Diagrams.

Verify component & hardware quantities received.

Familiarize yourself with the installation procedures.

1) Parts Inventory and Set-Up Confirm that all components, hardware and special tools are included (see Parts List).

Gather any additional tools necessary for installation (T40 & 1/2” wrench or socket).

Please follow diagrams and instructions in order.

2) Site location and Preparation Be sure site is of adequate size- allow for minimum fall zones (see Layout Diagram).

Be sure site is graded, level and free of debris for proper set-up and assembly.

Measure and mark site to determine structure location and orientation.

3) Assembly- General Please use correct type and length fasteners as shown in the installation procedure.

Before setting Play Structure modules in place, verify all hardware has been tightened.

Do not over tighten and tear the coating, tighten until washer was dimpled the coating NOT crushed. Be sure to follow the assembly order to ease the construction procedure.

I-3.5INRISERINSTrevA Page 2of 3

Assembly Components:

Item Qty. Description Drawing Part Number

A (2) Deck Assembly N/A

B (1) 12” Riser Step 935-525-0001

C (1) 24” Riser Step 935-525-0003

D (1) 6” Riser Step 935-525-0002

Hardware Components: (0-RISERHWKIT) Item Qty. Description Drawing Part Number

HA (8) 5/16-18 x 1 SS Truss Head Bolt 100-5161

HB (16) Flat Washer 1"x.4"x.07" 100-815FWSS

HC (8) 5/16-18 Nylon Lock Nuts SS 100-516NLNSS

Tools: (Supplied in the Installer’s Hardware Kit)

TA (1) Torx T-40TP Driver Bit 100-00T40

I-3.5INRISERINSTrevA Page 3of 3

1) Mount Riser to Decks by taking the Riser (B) and mounting it to the Structure Deck (A) using (4) 5/16-18 x 1 Bolts(HA), (8) SS Flat Washer 3/8" ID x 1" OD(HB), and (4) 5/16- 18 Nylon Lock Nuts SS(HC) at the bottom of the riser and bolt loosely. (See Figure).

2) Bolt the Riser (B) to the Structure Deck (A) using (4) 5/16-18 x 1" Bolts(HA), (8) SS Flat Washer 3/8" ID x 1" OD(HB), and (4) 5/16-18 Nylon Lock Nuts SS(HC) at the top of the riser and tighten bolts until stair coating dimples. Do NOT over tighten. (See Figure).

3) Tighten bolts at the bottom of the riser.

A 4-25-2012 MA DH

I-3.5INROOFINSTrevC Page 1 of 3

Childforms® FunPlay™ I-3.5INROOFINSTrevC

Roof Assembly:

NOTE:

These assemble shown with Roof and Mounts: which include (1) Square Roof, (4) Pole Mounts, and accessories. This assembly is not a stand alone structure, and must be connected to solidly build structure.

Please refer to guidelines as specified by the CPSC and ASTM F1487

Please review assembly and component Diagrams.

Verify component & hardware quantities received.

Familiarize yourself with the installation procedures.

1) Parts Inventory and Set-Up Confirm that all components, hardware and special tools are included (see Parts List).

Gather any additional tools necessary for installation (hex driver, level, tape measure, drill). Please follow diagrams and instructions in order.

2) Assembly- General Please use correct type and length fasteners included in the hardware kit for this assembly. Be sure to follow the assembly order to ease the construction procedure.

Start all screws before tightening them.

I-3.5INROOFINSTrevC Page 2 of 3

Assembly Components:

Item Qty. Description Drawing Part Number

A (1) Square Molded Roof revC 935-516-0002-X Rev C

Hardware Components: (0-3.5INROOFCHWKIT) Item Qty. Description Drawing Part Number

HA (4) #14 X 1.5" B6L SS Type A 100-14T27TP

Tools: (SUPPLIED IN INSTALLERS HW KIT) Item Qty. Description Drawing Part Number

TA (1) Torx T-27 Tamper Proof Driver Bit 100-00T27TP

TB (1) #7 Drill Bit 118 degree Jobbers Bit 100-07DB

Installation procedure:

1) Begin with completed Square Decking Assembly.

2) Situate the Roof (A) onto the poles. (Make sure poles are completely seated into the pockets on roof bottom.

I-3.5INROOFINSTrevC Page 3 of 3

3) Mark 3/8” from bottom of roof and drill hole (one per pole) through the roof and into the pole. Use the #7 drill bit provided in the HW kit.

4) Place the screws provided into each of these holes and tighten until the plastic just starts to dimple. (x4)

REV ECO DATE BY APRV

C 7-15-2020 MAA DAH

3/8”

Childforms® FunPlay™ I-3.5INSGLSLDINSTrevP

Single Straight or Curved Slide Assembly:

NOTE:

This assembly is not a stand alone structure, and must be connected to solidly build structure.

Please refer to guidelines as specified by the CPSC and ASTM F1487

● Please review assembly and component Diagrams.

● Verify component & hardware quantities received.

● Familiarize yourself with the installation procedures.

1) Parts Inventory and Set-Up

Confirm that all components, hardware and special tools are included (see Parts List).

Gather any additional tools necessary for installation (Drill, ¼”, and ½” drill bits). Please follow diagrams and instructions in order.

2) Assembly- General Please use correct type and length fasteners included in the hardware kit for this assembly. Be sure to follow the assembly order to ease the construction procedure. Start all screws before tightening them.

I-3.5INSGLSLDINSTrevP Page 1 of 6

Assembly Components:

Item Qty. Description Drawing Part Number

A (1) Straight Slide, 60” Tall 935-351-0025

OR

A (1) Curved Slide, 60” Tall 935-351-0026

B (1) Hood Panel 935-351-0001 (36” Wide Deck) 950-351-0013 (48” Wide Deck)

C (2) Slide Anchor 935-351-0016-W

D (2) Panel Mount Clamps 935-127-0001-B/G

E (1) Support Tube 935-520-0003-W (36” Wide Deck) 950-361-0002-W (48” Wide Deck)

Hardware Components: 0-3.5INSWSTRSLDHWKITrevD

HA. (4) 3/8 x 3/4 Torx Button Head Screws 100-3834

HB (4) Flat Washer 1"x.4"x.07" 100-815FWSS

HC (9) 3/8 Split Washer 100-38SW

HD (2) ¼ -20 x 3 Button Head Screws 100-14203

I-3.5INSGLSLDINSTrevP Page 2 of 6

HE (2) ¼-20” Toggle Anchors

100-14ANCHOR

HF (5) 5/16 x 2-1/2 Torx Button Head Screws 100-516212 HG (12) 1/4" x 1" Fender Washer 100-14WASH

HH (2) ¼” Hammer Drive Pin x 3/4” 100-14HDP34

HJ (2) ¼” Hammer Drive Pin x1-1/2” 100-14HDP

HL (5) 5/16 Nyloc Nut

100-516NLNSS

Tools:

TA (1) Socket Driver Bit T-45 100-00T45 TB (1) 5/32 Socket Driver Hex Bit 100-00H5/32

1) Lay Slide (A) on side and attach Anchor (C) to the bottom of slide using (4) 3/8 x 3/4

Screw (HA), (4) Flat Washer (HB), and (4) 3/8 Split Washer (HC).

2) With Anchors attached guide into footing holes as you place the Slide up to Decking.

3) Put top of slide face against deck, center slide to desired location. Align face of slide with the slots in deck. Mark on the slide face where each of the 5 bolts will go.

4) Move slide off of deck and drill a 3/8” diameter hole completely through the center marks made in the previous step.

I-3.5INSGLSLDINSTrevP Page 3 of 6

5) Attach slide to decking with (5) 5/16 x 2 1/2 Torx Button Head Screws(HF), (10) Flat

Washer(HG), (5) 3/8 Split Washer(HC), and (5) 5/16-18 Nyloc Nut(HL).

6) Insert Mounting Tube (E) into the provided hole in the side of the Panel (B). (See figure)

7) To mount the Slide Hood Place Clamp ear (Ref Clamp Assembly Manual) onto the ends of the Support Tube. Check for level and plumpness. Place Blank Clamp Half onto pole to match the Panel Mount Clamp Half. Leave loose until step #10 (See Figure).

8) Place Hood against the Slide and drill 1/4”hole through the Hood into the Slide.

I-3.5INSGLSLDINSTrevP Page 4 of 6

9) Move Panel away and use the ¼’ pilot hole in slide, ONLY SLIDE to drill ½” hole in the 1/4' pilot hole in the slide for toggle.

10)Place (2) ¼-20” Toggle Anchors in the ½”holes in the slide.

11)Place Hood back against slide and secure it to the slide with (2) ¼ -20 x 3" Button Head Screws(HD) and (2) ¼ x 1 Fender Washer(HG).

13) Tighten the clamps and secure to the sit-down pole with 3/4” drive pins (HH) by drilling a 1/4” hole into the top of each clamp ear in dimple (3/8” from the outside end) and into the railing that is being held. Once drive pin is in place tap down until flush with the clamp ear.

I-3.5INSGLSLDINSTrevP Page 5 of 6

14) When complete, plum and level; drill a 1/4” hole into clamp side and into the upright post. Use dimple on clamp as drill guide. Insert the 1-1/2” drive pin (HJ) into the freshly drilled hole and then tap it until pin is flush with clamp.

P 8/5/2014 MA

I-3.5INSGLSLDINSTrevP Page 6 of 6

I-3.5INVERTLOOPLDRINSTrevB---BPage 1of 5

Childforms® FunPlay™ I-3.5INVERTLOOPLDRINST

Vertical (Loop, Coil & Beanstalk)Ladder Assembly:

NOTE:

This assembly shown with Vertical Ladder and Vertical Ladder Grab Rail: which include (1) Vertical Ladder, (1) Vertical Ladder Grab Rail, (1) Anchor Posts and accessories. This assembly is not a stand alone structure, and must be connected to solidly build structure.

Please refer to guidelines as specified by the CPSC and ASTM F1487 Please review assembly and component Diagrams.

Verify component & hardware quantities received.

Familiarize yourself with the installation procedures.

1) Parts Inventory and Set-Up Confirm that all components, hardware and special tools are included (see Parts List).

Gather any additional tools necessary for installation. Please follow diagrams and instructions in order.

2) Assembly- General Please use correct type and length fasteners included in the hardware kit for this assembly. Be sure to follow the assembly order to ease the construction procedure. Start all screws before tightening them.

I-3.5INVERTLOOPLDRINSTrevB---BPage 2of 5

Assembly Components:

Item Qty. Description Drawing Part Number

A (1) 3.5" Arch Entrance / Exit with top connection 935-281-0012-Color

B (2) 3.5" Pole Mount Clamp Assembly (2 bolt) 935-127-0001- Color

C (1) Vertical Loop Ladder (48" max height) 935-281-0003- Color

OR

C (1) Vertical Coil Ladder (48" max height) 935-281-0004- Color

OR

C (1) Beanstalk Climber 935-281-0028- Color Installed at factory

(7) Beanstalk Climber Foot Treads 935-281-0028-01

(28) 5/16-18 x 1” SS Bolt 100-5161

(28) 5/16-18 Nylon Lock Nuts 100-516NLLSS

(28) SS Flat Washer w/ Neoprene Back 100-38WSSNP

I-3.5INVERTLOOPLDRINSTrevB---BPage 3of 5

Standard Hardware Components: 0-3.5INVERTLOOPLDRHWKIT Item Qty. Description Drawing Part Number

HA. (2) 5/16-18 x 1 Torx Button Head Screws 100-5161

HB (4) 5/16-18 Nylock Nut 100-516NLNSS

HC (2) 5/16 Neoprene Washer 100-38WSSNP

HC2 (2) Flat Washer 1”x.4”x.07” 100-815FWSS

HD (2) ¼” Hammer Drive Pin x 3/4” 100-14HDP34

HE (2) ¼” Hammer Drive Pin 100-14HDP

HF (2) 5/16-18 x 3/4 Torx Button Head Screws 100-51634

HG (4) 5/16 FW x 3/8 OD .045 Thk SS 100-516FW18-8

Tools: (Supplied in the Installer’s Hardware Kit) Item Qty. Description Drawing Part Number

TA (1) Torx Hex Bit T40 100-00T40

Installation procedure:

1. Place Clamp half (Ref Clamp Assembly Manual) onto the ends of the arch entrance/exit (A), (See Figure).

I-3.5INVERTLOOPLDRINSTrevB---BPage 4of 5

2. Mount Clamps (B) (See pole Clamp Assembly Manual) loosely onto support poles. Above Deck.

(see Figure)

3. Mount the Grab Rail to the Deck with (2) 5/16-18 x 1 Torx Button Head Screws (HA), (2) 5/16 Neoprene Washer (HC), (2) Flat Washer 1”x.4”x.07” (HC2), and (2) 5/16-18 Nylock Nut (HB) (see Feature).

NOTE: Neoprene washers to be placed with neoprene side against white powder coat finish of arch entrance/exit, and flat washer to be placed on back side of deck.

4. Drill ¼” hole into clamp ear (935-127-0001) and into the mounting grab rail. Insert ¼” hammer drive pin (HD) to secure grab rail for load bearing. Repeat as necessary for climber installation. (See Figure)

5. When complete, plum and level; drill a 1/4” hole into clamp sides and into the upright post posts.

Use dimple on clamp as drill guide. Insert the 1-1/2” drive pin (HE) into the freshly drilled hole and then tap it until pin is flush with clamp.

HA

HC

HC2

I-3.5INVERTLOOPLDRINSTrevB---BPage 5of 5

6. Place Vertical Loop/Coil Ladder (C) into pre-dug anchor hole and mount to the connector piece at the top of arch entrance/exit (A) using (2) 5/16-18 x 3/4 Torx Button Head Screws (HF), (4) 5/16 FW 3/8 OD x .045 Thk SS washer (HG), and (2) 5/16-18 Nylock Nut (HB). (see Feature)

REV ECO DATE BY APRV

A 02/19/2013 MA DH

B 6/10/2013 MA

HF HG

CAT Part Number: SWG-00033-G Description: Single 5” Post Swing, Single Bay Materials:

Frame: Color Green powder coated, f5”

OD,13 gauge steel tubing.

Seats: 5/16” Thick x 6” x 24” wide neoprene strap seat or 3/8” Thick x 9” Deep x f12” wide neoprene full bucket seat.

Chain: 5/16” welded zinc coated

Hardware: 318 Stainless Steel Truss-Head Hardware: 318 Stainless Steel Truss-Head bolts and locknuts

Dimensions:

Overall Height: 8’ High

Approximate Square Feet: 477.0 sq ft Actual Size: 11’-8” x 0’-5” Actual Use Zone: 23’-8” x 32’-0” Assembled Weight: 200 lbs

Fall Zone: Overhead fall zone views are for planning purposes only. Please follow guidelines as specified by the CPSC and ASTM F1487

I-SWGSPINSTrevC Page 1 of 9

Childforms® I-SWGSPINSTrevC

Single Post Swing Set Assembly Instructions:

Please read and follow all Safety Information.

Please review assembly and component Diagrams.

Verify component & hardware quantities received.

Familiarize yourself with the installation procedures.

Safety Play site ground material should only be of an approved, shock-absorbing type and meet minimum depth requirements. NEVER install playground equipment over paved or hard surfaces.

Be sure that minimum fall zone requirements are met.

Do not allow children to play on or near equipment which is in need or repair or replacement, is incomplete or is otherwise considered unsafe.

Parts Inventory and Set-Up Confirm that all components, hardware and special tools are included (see Parts List).

Gather any addition tools necessary for installation (hex driver, 9/16” Wrench, level, tape measure, etc) Please follow diagrams and instructions in order.

1) Site location and Preparation Be sure site is of adequate size- allow for minimum fall zones (see Layout Diagram).

Be sure site is graded, level and free of debris for proper set-up and assembly..

Measure and mark site to determine structure location and orientation.

2) Assembly- General Please use correct type and length fasteners as shown in the installation procedure.

Before setting Play Structure modules in place, verify all hardware has been tightened.

Be sure to follow the assembly order to ease the construction procedure.

I-SWGSPINSTrevC Page 2 of 9

Assembly Components:

Item Qty. Description Drawing Part Number

A (1) 5" Saddle Clamp Horizontal Beam 450-00002-(Color)

B (2) Single 5" Swing Post w/Ledger Ring 450-00004-(Color)

B1 (2) 5" Dome Cap 950-576-0001-(Color)

C (2) Saddle Clamp Backs 450-00020-01-(Color)

Swing Assembly Components: 0-SWGSP5HWKIT Item Qty. Description Drawing ___________ Part Number

HA (12) 3/8-16 x 1.25" T6L SS w/Patch 100-38114 HB (24) Flat Washer 1" x 4" x .07" 100-815FWSS HC (12) 3/8-16" Nylon Lock Nut SS 100-38NLNSS HD (4) Hammer Drive Pin 1/4" x 3/4" Reach 100-14HDP34

Swing Seat Assembly Components: 0-SWGALLSEATHW (Belt Seat Assembly) Item Qty. ______ Description Drawing Part Number HE (1) Belt Seat & Chain Assembly for 96" high top beam 450-80008

(Each Assembly Completes 1 Swing Bay)

(4) 1/2-13 Hex shoulder/2.45"threads Zinc 100-122SPEC

(4) 1/2-13 Nylon Lock Nut Zinc 100-12NLNZ

(4) Swing Shackle 450-00005

(4) Shackle Pendulum for Swing Hanger 450-0000

(4) Chain pre-cut for seat and beam height 450-00007

(2) 450-00008 Belt Seat

I-SWGSPINSTrevC Page 3 of 9

Swing Assembly Components: 0-SWGALLSEATHW (Full Bucket Seat Assembly) Item Qty. Part No. Description Drawing Part Number HF (1) 450-80009 Full Bucket & Chain Assembly for 96" high top beam

(Each Assembly Completes 1 Swing Bay)

(4) 1/2-13 Hex shoulder/2.45"threads Zinc 100-122SPEC

(4) 1/2-13 Nylon Lock Nut Zinc 100-12NLNZ

(4) 450-00005 Seat to Chain Shackle

(4) 450-00006 Shackle Pendulum for Swing Hanger

(4) 450-00007 Chain pre-cut for seat and beam height

(2) 450-00009 Full Bucket Seat

TOOLS

Item Qty. Part No. Description Drawing

TA (1) 100-00T45 T-45 Torx Driver Bit

TB (1) 100-T00516 5/16” Hex (tamper proof) Driver Bit

I-SWGSPINSTrevC Page 4 of 9

Layout Diagram

For any additional bays add 10’-10” in Use Zone space.

NOTE: Overhead views are for planning purposes only.

Please follow guidelines as specified by the CPSC and ASTM F1487.

Installation procedure:

1) Attach swing horizontal beam (A) to swing posts (B) by placing horizontal beam with saddle clamp around the upright post and seated on the ledge.

2) Place saddle clamp back (C) on upright post and align with saddle clamp on top rail.

Now bolt together using (6) bolts (HA), (12) washers (HB), and (6) nuts (HC).

I-SWGSPINSTrevC Page 5 of 9

3) Insert (2) HD drive pins in clamps by drilling a 1/4” through upright post by using pre-drilled hole in clamp as a guide. Now insert drive pin in holes and tap down with hammer.

4) When placing Posts into the ground be sure to dig (2) holes 18” diameter by 36” deep;

132” apart. [When doing multiple bays add 134” for each consecutive hole center.] Place 12” rebar though the center holes that are perpendicular to the swing. With assistance, lower the Swing set into the holes - securely prop Swing set Assembly with wood or similar temporary bracing structural material with the bottom of the Horizontal Beam. Level beam and adjust height to equal 96” (8 feet) above the finished surfacing.

[i.e. 12” of surfacing beam is placed 108” (9 feet) above grade once surfacing is installed at 12” the beam is at the correct height] Be sure Posts are plum and the horizontal beam is level. Mix and pour concrete into holes, leaving concrete 2” below ground level(Use a soupy mix). Let swing remain undisturbed for (3) days minimum until concrete has fully set.

Hole Layout

36.0

I-SWGSPINSTrevC Page 6 of 9

5) After Swing set Frame Footers have fully set, through bolt Swing Seat Assemblies (HE/HF) using Hex Bolt and Lock Nut included in Seat Assembly (See Diagram). Tighten bolts to fully engage Lock Nuts, (NOTE: Do not bind pivot hangers, be sure pendulums swing freely)

For Add-A-Bay Installation

PARTS LIST

Assembly Components:

Item Qty. Description Drawing Part Number

A (1) 5" Saddle Clamp Horizontal Beam 450-00002-(Color)

B (1) Single 5" Swing Post w/Ledger Ring 450-00004-(Color)

B1 (1) 3.5" Dome Cap or (2) 5" Dome Cap 935-576-0001-(Color) [Installed at Factory]

C (1) Saddle clamp backs 450-00020-01-(Color)

Hardware Components: 0-SWGSP5ADDBAYHW (Note this kit will complete 1 add-a-bay) Item Qty. Description Drawing Part Number

HA (6) 3/8-16 x 1.25 Torx Button Head Screws 100-38114

HB (12) Flat Washer 1”x.4”x.07” 100-815FW

HC (6) 3/8 Nylock Nut 100-38NLNS

I-SWGSPINSTrevC Page 7 of 9

SEATS

Item Qty. Part No. Description Drawing

(Swing Assembly Components: 0-SWGALLSEATHW (Belt Seat Assembly) Item Qty. Part No. Description Drawing Part Number HE (1) 450-80008 Belt Seat & Chain Assembly for 96" high top beam

(Each Assembly Completes 1 Swing Bay)

(4) 1/2-13 Hex shoulder/2.45"threads Zinc 100-122SPEC

(4) 1/2-13 Nylon Lock Nut Zinc 100-12NLNZ

(4) 450-00005 Swing Shackle

(4) 450-00006 Shackle Pendulum for Swing Hanger

(4) 450-00007 Chain pre-cut for seat and beam height

(2) 450-00008 Belt Seat Swing Assembly Components: 0-SWGALLSEATHW (Full Bucket Seat Assembly) Item Qty. Part No. Description Drawing Part Number HF (1) 450-80009 Full Bucket & Chain Assembly for 96" high top beam

(Each Assembly Completes 1 Swing Bay)

(4) 1/2-13 Hex shoulder/2.45"threads Zinc 100-122SPEC

(4) 1/2-13 Nylon Lock Nut Zinc 100-12NLNZ

(4) 450-00005 Seat to Chain Shackle

(4) 450-00006 Shackle Pendulum for Swing Hanger

(4) 450-00007 Chain pre-cut for seat and beam height

(2) 450-00009 Full Bucket Seat

I-SWGSPINSTrevC Page 8 of 9

1) Attach swing horizontal beam (A) to swing posts (B) by placing horizontal beam with saddle clamp around the upright post and seated on the ledge.

2) Place saddle clamp back (C) on (2) upright posts located on the outside of swing frame and align with saddle clamp on top rail. Interior uprights will have (2) horizontal beams, no clamp back (C) will be required. Now bolt together using (6) bolts (HA), (12) washers (HB), and (6) nuts (HC). For center upright posts horizontal beams will be bolted together using (6) bolts (HA), (12) washers (HB), and (6) nuts (HC)

3) Insert (2) drive pins in clamps by drilling a 1/4” through upright post by using pre-drilled hole in clamp as a guide. Now insert drive pin in holes and tap down with hammer.

4) When placing Posts into the ground be sure to dig (2) holes 18” diameter by 30” deep;

132” apart. [When doing multiple bays add 134” for each consecutive hole center.] Place 12” rebar though the center holes that are perpendicular to the swing. With assistance, lower the Swing set into the holes - securely prop Swing set Assembly with wood or similar temporary bracing structural material with the bottom of the Horizontal Beam. Level beam and adjust height to equal 96” (8 feet) above the finished surfacing. [i.e. 12” of surfacing beam is placed 108” (9 feet) above grade once surfacing is installed at 12” the beam is at

I-SWGSPINSTrevC Page 9 of 9 the correct height] Be sure Posts are plum and the horizontal beam is level. Mix and pour concrete into holes, leaving concrete 2” below ground level(Use a soupy mix). Let swing remain undisturbed for (3) days minimum until concrete has fully set.

5) After Swing set Frame Footers have fully set, through bolt Swing Seat Assemblies (HE/HF) using Hex Bolt and Lock Nut included in Seat Assembly (See Diagram). Tighten bolts to fully engage Lock Nuts, (NOTE: Do not bind pivot hangers, be sure pendulums swing freely)

REV ECO DATE BY APRV

A 09-0002 7-2-09 8-4-09 RP DHZ

B Design Change to Saddle Clamp Horizontal Beam 1-29-15 MA DAH C Remove 3.5" Swing Sections, Correct BOM 10-13-17 MA DAH