Addendum One.pdf

PDF 747 KB Posted Aug 9, 2023

Attached to: RFB-21-24 KCTCS Upgrade Life Safety Somerset CC
Solicitation number: RFB 785 2400000012 2
Issued by: Ohio County, Kentucky

About this file

Written by GovTribe AI · Mar 11, 2026

This is Addendum One to an Invitation to Bid (RFB-21-24) issued by the Commonwealth of Kentucky Department for Facilities and Support Services, Division of Engineering and Contract Administration, for an Upgrade Life Safety Bid Package #1 at KCTCS Somerset Community & Technical College in Somerset, Kentucky. The project, designated RFB-785-2400000012 with KFI Project Number 22-0864.00, involves comprehensive fire detection and alarm system upgrades across multiple buildings, including the replacement of fire alarm control panels (FACP), initiation devices such as smoke and heat detectors, annunciator panels, flow and tamper switches, speaker/strobe devices, and related infrastructure. The addendum, dated August 9, 2023, modifies specifications and drawings to clarify installation requirements, device quantities, system interconnections, and contractor responsibilities. Key clarifications address the retention of existing tamper switches integral to valves with new addressable modules for interface, the inclusion of Category 6 cabling for IP dialer connections, voice evacuation system installation in Building 1 only with speaker/strobe provisions for future expansion in other buildings, and the interconnection of fire alarm panels using existing campus fiber network infrastructure with the Building 1 South Campus panel serving as the master station.

The addendum establishes that the contractor is responsible for preparing and submitting documentation for State Fire Marshall approval, with Notifier designated as the basis of design system manufacturer. Contractor responsibilities include replacing ceiling tiles and drywall damaged during construction, with KCTCS responsible for asbestos testing and abatement on existing sprinkler piping. The site will remain occupied during installation, requiring coordination with school personnel to minimize disruption to classes. The contractor must work with the owner and KFI Engineers to establish a detailed phasing and construction schedule, as no published schedule is provided. Flow tests conducted by KFI Engineers are to be utilized rather than contractor-performed tests. The contractor bears responsibility for HBC plan review fees. Existing fire alarm system components, including all devices and cabling, will be replaced with new installations, except for tamper switches integral to valves and existing raceways and backboxes, which are to remain and be reused as appropriate.

View the file

Other files

File	Type	Posted
Final_RFB_785_2400000012_1_SO_FORM.PDF	PDF	Aug 9, 2023
Final_RFB_785_2400000012_2_SO_FORM.PDF	PDF	Aug 9, 2023

On GovTribe

Work with this file

Download the original file
Contacts named in this file
Similar government files
Ask GovTribe AI about this file

Try for free Login

Text version

The file's text, extracted by GovTribe without its formatting.

COMMONWEALTH OF KENTUCKY

DEPARTMENT FOR FACILITIES AND SUPPORT SERVICES

DIVISION OF ENGINEERING AND CONTRACT ADMINISTRATION

INVITATION TO BID NO: RFB-21-24

FOR: Upgrade Life Safety Bid Package #1 KCTCS- Somerset Community & Technical College Somerset, Kentucky

DATE: August 9, 2023

RFB-785-2400000012

ADDENDUM NO. One (1)

BIDDER SHALL CONFORM TO THE FOLLOWING CHANGES AS SAME SHALL BECOME BINDING

UPON THE CONTRACT TO BE ISSUED IN RESPONSE TO THIS INVITATION TO BID.

Item 1: Refer to addendum to be distributed by Lynn Imaging for all additions, deletions, and/or changes to specifications and/or drawings.

END OF ADDENDUM

Invitation to Bid No. RFB-21-24 For: Upgrade Life Safety Bid Package #1 KCTCS- Somerset Community & Technical College Somerset, Kentucky

Susan Ward, Statewide Procurement Analyst II Division of Engineering and Contract Administration

ADDENDUM

Page 1 of 4 Find a way.

Date: August 8, 2023

Project: RFB-21-24 KCTCS – Upgrade Life Safety – Bid Package #1

KFI Project Number: 22-0864.00

Addendum Number: 01

THIS ADDENDUM IS A CONTRACT DOCUMENT AND MAY APPLY TO ANY OR ALL CONTRACTS AND SUBCONTRACTS UNLESS OTHERWISE SPECIFIED HEREIN OR SHOWN ON THE ATTACHED DRAWINGS (IF ANY). ALL WORK REQUIRED BY THIS ADDENDUM SHALL BE IN COMPLETE ACCORD WITH THE CONTRACT DOCUMENTS AND SUBSEQUENT ADDENDA THERETO. THE ITEMS LISTED IN THIS ADDENDUM ARE NOT IN ANY ORDER IN REGARD TO THE DRAWINGS OR THE SPECIFICATIONS. ALL CONTRACTORS ARE CAUTIONED TO EXAMINE EACH AND EVERY ITEM OF THIS ADDENDUM.

THE FOLLOWING CHANGES OR CLARIFICATIONS TO THE PLANS & SPECIFICATIONS SHALL BE INCLUDED AS PART OF THE CONTRACT DOCUMENT

SPECIFICATION CHANGES:

1. Section Number: 28 46 00 FIRE DETECTION AND ALARM

a. Replace section 28 46 00 in it’s entirety with attached specification section

PLAN SHEET CHANGES:

1. FA000 – FIRE ALARM GENERAL NOTES - SITE PLAN – SYMBOLS

a. Add symbol and definition for ‘FAAP’

2. S1-FA110 - BUILDING 1 FIRE ALARM DEMOLITION - LEVEL 1

a. Revised quantities of existing flow and tamper switches to be removed. Revised keynote 4.

3. S1-FA210 - BUILDING 1 FIRE ALARM - LEVEL 1

a. Clarified quantity of flow and tamper switches to be installed. Added Keynote E13.

4. S5-FA110 - BUILDING 5 FIRE ALARM DEMOLITION - LEVEL 1

a. Revised quantity of existing heat detectors to be removed.

5. S5-FA210 - BUILDING 5 FIRE ALARM - LEVEL 1

a. Revised quantity of heat detectors to be installed.

CONTRACTOR QUESTIONS (Responses in Blue)

1. Building 1 drawing S1-FA110. Keynote 4. Need clarification on what is to be removed. The building currently has 3 flow switches and 5 tamper switches. 3 of these tamper switches are internal to the valve and would require replacing the entire valve.

a. All (3) flow switches to be replaced with new. (2) Tamper switches to be replaced with new.

(3) existing tamper switches integral to the valve to remain and interfaced with new fire alarm system. Provide addressable modules as required to interface with new system. Refer to revised Addendum 1 drawings.

2. Building 1 drawing S1-FA210. Keynote E12. Need clarification on purpose of Cat6 cable from new fire panel to existing port (is this for Starlink dialer?)?

a. Yes – the Cat6 data connection is to allow for IP dialer.

Page 2 of 4 Find a way.

3. Building 1 drawing S1-FA210. Please define FAAP notation on drawing. Currently not in legend.

a. FAAP is to indicate Fire Alarm Annunciator Panel. Symbol legend to be revised in Addendum

1 Drawings.

4. Building 2 drawing S2-FA210. Keynote E12. Need clarification on purpose of Cat6 cable from new fire panel to existing port (is this for Starlink dialer?)?

a. Yes – the Cat6 data connection is to allow for IP dialer.

5. Building 2 drawing S2-FA210 – Wall mount speaker strobe light is indicated on drawings. Please clarify if the building is to have audio voice system?

a. Voice system to be included in Building 1 only. Provide speaker/strobe devices throughout to allow ability for future voice system.

6. Building 4 drawing S4-FA210 - Keynote E12. Need clarification on purpose of Cat6 cable from new fire panel to existing port (is this for Starlink dialer?)?

a. Yes – the Cat6 data connection is to allow for IP dialer.

7. Building 4 drawing S4-FA210- Wall mount speaker strobe light is indicated on drawings. Please clarify if the building is to have an audio voice system?

a. Voice system to be included in Building 1 only. Provide speaker/strobe devices throughout to allow ability for future voice system.

8. Building 4 drawing S4-FA210- Keynote E9. Are fire control panels required to be interconnected?

a. Fire alarm panels are to be interconnected using the existing campus fiber network. FACP in Building 1 of South Campus is to serve as the master station for the South Campus.

9. Building 5 drawing S5-FA110-Keynote 2. Drawing shows 3 smoke detectors in diesel garage when there are currently 5 heat detectors instead of smoke detectors in diesel garage. Clarification needed on what to remove and install.

a. Existing devices to be replaced 1-for-1. All (5) heat detectors to be replaced with new. Refer to revised Addendum 1 Drawings for clarification.

10. Building 5 drawing S5-FA210- Wall mount speaker strobe light is indicated on drawings. Please clarify if the building is to have an audio voice system?

a. Voice system to be included in Building 1 only. Provide speaker/strobe devices throughout to allow ability for future voice system.

11. Stoner Building drawing Sto-FA210- Wall mount speaker strobe light is indicated on drawings. Please clarify if the building is to have an audio voice system?

a. Stoner building is not to receive an audio voice system. Provide speaker/strobe devices throughout to allow ability for future voice system.

12. Will there be a Ceiling tile replacement allowance and unit price, The ACT Ceiling Tiles are old some are damaged wet and stained there are several rooms within the buildings that the ceiling Tiles have absorbed moisture and sagging unable to salvage and reuse the affected tiles.

a. Contractor to replace all tiles damaged by construction.

13. Will there be a Dry Wall Allowance for replacement of ceilings and Unit price? There will be a few areas Rooms within the building of Hard D W ceiling that will need to be removed to install the sprinkler systems and Drywall replaced including Paint.

a. Contractor responsible for repairing and painting all ceilings damaged during construction.

14. Have the Buildings been tested for Asbestos on the Existing Limited area Sprinkler piping that is to be removed?

Page 3 of 4 Find a way.

a. KCTCS will test and abate all asbestos found or suspected. There will be a document that addresses this issue dealt with during pre-construction meeting.

15. The Diesel Shop has two water stubs in the floor. The domestic is connected to the larger 6'' or 8'' floor stub. Will this Domestic connection remain on the Fire Line or will the domestic be re-piped to the domestic floor stub?

a. Domestic connection will remain.

16. Can a set of as-built water utility site drawings be provided for the Diesel shop and Stoner?

a. All site utility plans available will be provided to the successful bidder.

17. Will the Design Team provide Fire Alarm Inspection Reports so that the FA contractor can confirm the location of all FA devices?

a. The Fire Alarm Inspection Reports will be provided to the successful bidder.

18. Will a Sprinkler Flow test be required for Diesel shop and Stoner Building?

a. No. Flow tests conducted by KFI Engineers are to be utilized.

19. Will Contractor be responsible for the HBC plan review fees?

a. Yes

20. Will there be a published more detailed Project Phasing schedule per Building outlining the allotted time for each building?

a. No. The awarded contractor will be responsible for working with the owner and KFI to determine a complete phasing and construction schedule.

21. Will any of the spaces be Occupied during the installation of the sprinkler and FA?

a. Yes. The awarded contractor will have to work with school personnel to complete the work without disruption to classes.

22. Will the furnishings remain in each space during construction?

a. To be determined during construction. Contractor to assume the rooms will contain furnishings.

23. Following is the block question in regards to the “Fire Alarm Annunciator Panel”. There is a line from the new “Fire Alarm control Panel” to that Annunciator Panel, however, there is nothing in the Spec that states what type of connection is needed and what information the Annunciator Panel is needing via that connection (see diagram following)…

a. The drawing # FA301 shows the following Riser Diagram (see attached diagram). At the top of that diagram, it shows a line to "TO EXISTING FIRE ALARM CIRCUITS/DEVICES AND ZONES".

i. Please provide details as to what specifically these Zones are and the type and manufacturer of the devices that must be connected.

1. Existing annunciation devices (horn/strobes) to be replaced with new devices. Existing zoning to remain.

2. Existing initiation devices (smoke detectors, etc.) to be replaced with new devices. Existing zoning to remain.

ii. Is there a specific "FA System" (eg: Simplex, Siemens, etc.) that must be connected to the new FA Control Panel?

1. Existing system to be replaced with new. New Fire Alarm Control panel is not to be interfaced with existing panels. Basis of design for new system is Notifier.

iii. What components of the existing FA circuit/System are you wanting to keep?

Page 4 of 4 Find a way.

1. All devices and cabling of the existing fire alarm system will be replaced with new, except existing tamper switches integral to valves. These are to be interfaced with new system using addressable fire alarm relays and new cabling to new FACP. Existing raceway and backboxes for annunciators and initiation devices to remain. New cabling to be provided throughout.

b. For "shut down" of the RTUs, is a contact closure per RTU adequate for FA shutdown? If so, do these contacts already exist?

i. One contact closure per RTU is adequate. Existing contact closures are to be replaced with new and interfaced with new fire alarm system with addressable auxiliary relays. Contractor to verify all quantities and locations of existing contact closures.

24. The drawings are not KY State Fire Marshall approved.

a. Do you expect the FA contractor to provide detailed drawings and engineering time for the

State submittal/approval process?

i. Yes. FA contractor shall be responsible for preparing and submitting documentation required for approval from the State Fire Marshall.

b. Does the customer have a preferred FA Manufacturer (Simplex, Siemens, etc.)?

i. Basis of design system manufacturer is Notifier.

END OF ADDENDUM

E100

DETAIL NUMBER

SHEET NUMBER

GENERAL

ELECTRICAL KEYED NOTE NUMBER

INDICATES ALL DEVICES UNDER ONE COVERPLATE

RACEWAY SYSTEMS

CONDUIT CONCEALED IN WALL OR CEILING

CONDUIT CONCEALED IN / UNDER FLOOR

CONDUIT RUN EXPOSED

CONDUIT TRANSITION UP

CONDUIT TRANSITION DOWN

JUNCTION BOXJ

JUNCTION BOX - FLOOR MOUNTEDJ

JUNCTION BOX - WALL MOUNTEDJ

PULL BOXB

MAN HOLEH

HAND HOLEH

FLOOR

VERIFY

SECURITY SYSTEMS

CCTV CAMERA (1D UNLESS NOTED OTHERWISE)

13'-0" /

CEILING

CAMERA

LEGEND

180 - 180 DEGREE VIEW RANGE

270 - 270 DEGREE VIEW RANGE

360 - 360 DEGREE VIEW RANGE

PTZ - PAN, TILT, ZOOM

WALL MOUNTED SECURITY DEVICES

CR SEE BELOW

WALL

SECURITY

LEGEND

AI - INTERCOM

CR - CARD READER

DC - DOOR CONTACT

EL - ELECTRIC LOCK

ES - ELECTRIC STRIKE

GB - GLASS BREAK DETECTOR

KB/F - KNOX BOX

KP - KEY PAD

KS - KEYED SWITCH

LM - LATCH MONITOR

LD - LOCKDOWN STROBE

ML - MAGNETIC LOCK

PB - PANIC BUTTON

REX - REQUEST TO EXIT

RR - REMOTE DOOR RELEASE

VI - VIDEO INTERCOM STATION

XP - EXIT PUSHBUTTON

XS - EXIT SENSOR

48" 42"

VERIFY

48" 48"

VERIFY

6" ABOVE DOOR

ABOVE

COUNTER

48" 48"

VERIFY

SECURITY DEVICES DE SEE BELOW

SECURITY

LEGEND

DE - DELAYED EGRESS

LA - LOCAL ALARM

MD - MOTION DETECTOR

CEILING

VERIFYAC ACCESS CONTROL EQUIPMENT / PANEL

PUSHBUTTON - SINGLE 48"

PUSHBUTTON - DOUBLE 48"

BUZZER 90"

BELL 90"

FIRE ALARM SYSTEMS

MANUAL STATION 48"

WALL MOUNTED HORN 80"

CEILING MOUNTED HORNF

WALL MOUNTED STROBE LIGHT 80"F

CEILING

CEILING MOUNTED STROBE LIGHTF CEILING

WALL MOUNTED HORN AND STROBE LIGHT 80"F

CEILING MOUNTED HORN AND STROBE LIGHT CEILINGF

WALL MOUNTED SPEAKER 80"F

CEILING MOUNTED SPEAKERF CEILING

WALL MOUNTED SPEAKER AND STROBE LIGHT 80"F

CEILING MOUNTED SPEAKER AND STROBE LIGHT CEILINGF

WALL MOUNTED SPEAKER AND STROBE LIGHT

WITH MESSAGE BOARD

80"F MB

CEILING MOUNTED SPEAKER AND STROBE

LIGHT WITH MESSAGE BOARDF MB CEILING

WALL MOUNTED CHIME AND STROBE LIGHT 80"F

WALL MOUNTED BELL 80"F

WALL MOUNTED REMOTE RESET FOR DUCT

DETECTOR

48"F RS

FIRE ALARM DEVICEF SEE BELOW

FIRE

ALARM

LEGEND

F/S - FIRE / SMOKE DAMPER

H - HEAT DETECTOR

H/S - HEAT / SMOKE DETECTOR

IR - INFRARED SENSOR

MD - MAGNETIC DOOR HOLDER

R - INTELLIGENT CONTROL RELAY MODULE

S - SMOKE DETECTOR

SD - SMOKE DAMPER

SR - SMOKE DETECTOR WITH RELAY

SS - FIRE SUPRESSION SYSTEM

48"

CEILING

VERIFY

CEILING

VERIFY

CEILING

VERIFY

BEAM DETECTOR TRANSMITTER VERIFYF T

BEAM DETECTOR RECEIVER VERIFYF R

FLOW SWITCH VERIFYF FS

FLOW SWITCH VERIFYF TS

FACP

FIRE ALARM CONTROL PANEL - SURFACE MOUNT TOP 72"

FAA FIRE ALARM CONTROL - FLUSH MOUNT MAX TOP 72"

VCA FIRE ALARM VOICE COMMAND

ANNUNCIATOR - SEMI-FLUSH MOUNT

MAX TOP 72"

FAAP FIRE ALARM ANNUNCIATOR PANEL VERIFY

ABBREVIATIONS

& AND

@ AT

℄ CENTERLINE

° DEGREE (S)

Ø PHASE OR ROUND

# POUND OR NUMBER

AFCI ARC FAULT CURRENT INTERRUPTER

AFF ABOVE FINISHED FLOOR

AFG ABOVE FINISHED GRADE

APP ALARM ANNUNCIATOR PANEL

AL ALUMINUM

AMP AMPERE

APPROX APPROXIMATE

ARCH ARCHITECT/ARCHITECTURAL

ATS AUTOMATIC TRANSFER SWITCH

AUTO AUTOMATIC

BAS BUILDING AUTOMATION SYSTEM

BOT BOTTOM

C CONDUIT

CAB CABINET

CB CIRCUIT BREAKER

CCTV CLOSED CIRCUIT TELEVISION

CLG CEILING

C/T CURRENT TRANSFORMER

D DEPTH

DIV DIVISION

DWG DRAWING

EA EACH

EM EMERGENCY

ELEV ELEVATOR

EQUIP EQUIPMENT

EWC ELECTRIC WATER COOLER

EXT EXTERIOR

FAA FIRE ALARM ANNUNCIATOR PANEL

FACP FIRE ALARM CONTROL PANEL

GC GENERAL CONTRACTOR

GEN GENERATOR

GFCI GROUND FAULT CIRCUIT INTERRUPTER

G/GND GROUND

GMB GROUNDING MAIN BUS BAR

H HEIGHT

HP HORSE POWER

HZ HERTZ

INT INTERIOR

JB JUNCTION BOX

KV KILOVOLT

KVA KILOVOLT AMPS

KW KILOWATT

L LENGTH

LF LINEAL FOOT

LS LIFE SAFETY

LV LOW VOLTAGE

LFC LIQUID TIGHT FLEXIBLE CONDUIT

L/LT LIGHT

LTS LIGHTS

LTG LIGHTING

MATV MASTER ANTENNA TELEVISION

MAX MAXIMUM

MCC MOTOR CONTROL CENTER

MECH MECHANICAL

MEZZ MEZZININE

MFR MANUFACTURER

MIN MINIMUM

MISC MISCELLANEOUS

MS MOTOR STARTER

MSP MOTOR STARTER PANEL

MSS MOTOR STARTER SWITCH

N/A NOT APPLICABLE

NL NIGHT LIGHT

N.T.S NOT TO SCALE

PF POWER FACTOR

PIV POST INDICATOR VALVE

PNL PANEL

PVC POLYVINYL CHLORIDE

R/RECEPT RECEPTACLE

RM ROOM

SCHED SCHEDULE

SECT SECTION

S/D SMOKE DAMPER

SF SQUARE FOOT

SHT SHEET

SM SURFACE MOUNTED

SP SUMP PUMP

SPEC SPECIFICATIONS

STD STANDARD

SUSP SUSPENDED

SW SWITCH

SW. BD SWITCHBOARD

SW. GR SWITCHGEAR

TEL TELEPHONE

TERM TERMINAL

TGMB TELECOMMUNICATION GROUNDING

MAIN BUS BAR

TV TELEVISION

TYP TYPICAL

UG UNDERGROUND

UNO UNLESS NOTED OTHERWISE

V VOLTAGE

VA VOLT AMPERE

W WATT (S)

W WIDTH

W/ WITH UNIT

WG WIRE GUARD

WP WEATHERPROOF

XFRM TRANSFORMER

JUNCTION BOX (NOMINAL TRADE SIZE) SCHEDULE

J-BOX TRADE SIZE J-BOX ACTUAL SIZE

MINIMUM VOLUME

(PER NEC 314.16A)

1-GANG 4" x 3" x 2-1/8" 21.0 CUBIC INCHES

2-GANG 4-11/16" x 4-11/16" x 3-1/2" 42.0 CUBIC INCHES

3-GANG 8-5/8" x 4-1/2" x 3-1/2" 63.0 CUBIC INCHES

4-GANG 10-7/16" x 4-1/2" x 3-1/2" 84.0 CUBIC INCHES

5-GANG 12-1/4" x 4-1/2" x 3-1/2" 105.0 CUBIC INCHES

6-GANG 14-1/16" x 4-1/2" x 3-1/2" 126.0 CUBIC INCHES

4" SQUARE x 1-1/4"D 4" x 4" x 1-1/4" 18.0 CUBIC INCHES

4" SQUARE x 1-1/2"D 4" x 4" x 1-1/2" 21.0 CUBIC INCHES

4" SQUARE x 2-1/8"D 4" x 4" x 2-1/8" 30.3 CUBIC INCHES

4-11/16" SQUARE x 1-1/4"D 4-11/16" x 4-11/16" x 1-1/4" 25.5 CUBIC INCHES

4-11/16" SQUARE x 1-1/2"D 4-11/16" x 4-11/16" x 1-1/2" 29.5 CUBIC INCHES

4-11/16" SQUARE x 2-1/8"D 4-11/16" x 4-11/16" x 2-1/8" 42.0 CUBIC INCHES

CONDUIT ROUTING AND SEPARATION

GROUP A

277V, 480V ELECTRONIC DIMMER

CONTROL, LIGHTING,

SWITCHED POWER SOURCES & HIGH

CURRENT SOURCES

(120V, 40A OR GREATER)

120V, 20A POWER SERVICE

B C D

ADJACENT 6" [152 mm] 12" [305 mm] 12" [305 mm]

- - 12" [305 mm] 6" [152 mm]

- - ADJACENT 6" [152 mm]

- - - ADJACENT

36" [914 mm] 12" [305 mm] 6" [152 mm] 12" [305 mm]

12" [305 mm] 6" [152 mm] ADJACENT 6" [152 mm]

24" [610 mm] 12" [305 mm] 6" [152 mm] 12" [305 mm]ALL OTHER POWER SOURCES

GENERAL FIRE ALARM DEMOLITION NOTES

A. DRAWINGS ARE DIAGRAMMATIC ONLY AND ARE NOT INTENDED TO INDICATE ALL DEVICES

OR CONDITIONS ASSOCIATED WITH DEMOLITION. IT SHALL BE THE CONTRACTOR'S

RESPONSIBILITY TO FIELD VERIFY ACTUAL CONDITIONS INVOLVED IN THE DEMOLITION

AND SUBSEQUENT RECONSTRUCTION REQUIRED TO COMPLETE THE ELECTRICAL

INSTALLATION.

B. SEE ARCHITECTURAL/GENERAL DRAWINGS AND SPECIFICATIONS FOR PHASES OF

DEMOLITION.

C. CIRCUIT CONTINUITY SHALL BE MAINTAINED TO ELECTRICAL LIGHTING, DEVICES, AND

EQUIPMENT REMAINING, BUT AFFECTED BY DEMOLITION. PROVIDE NEW CONDUIT AND

WIRING AS NECESSARY TO MAINTAIN CONTINUITY TO EXISTING EQUIPMENT AND DEVICES.

FIELD VERIFICATION OF BRANCH CIRCUIT CONFIGURATION SHALL BE THE RESPONSIBILITY

OF THE ELECTRICAL CONTRACTOR.

D. IN AREAS OF DEMOLITION, REMOVE ASSOCIATED JUNCTION BOXES, SUPPORTS, CONDUIT

AND WIRING TO THE POINT OF ORIGIN FOR LIGHTING, DEVICES AND EQUIPMENT NOT

BEING REUSED.

E. FOR CIRCUITS/HOMERUNS WITH ONLY A PORTION DEMOLISHED, REMOVE CONDUIT AND

CONDUCTORS BACK TO THE NEAREST JUNCTION BOX FEEDING CIRCUITS BUT MAINTAIN

POWER TO EQUIPMENT AND RECEPTACLES THAT WILL REMAIN AFTER DEMOLITION OR

REQUIRE POWER DURING DEMOLITION AND CONSTRUCTION.

F. FOR CIRCUITS/HOMERUNS WITH ALL DEVICES DEMOLISHED, REMOVE CONDUIT AND

CONDUCTORS BACK TO THE PANELBOARD SERVING CIRCUIT(S).

G. DASHED ELECTRICAL DEVICES INDICATE DEVICES THAT ARE TO BE DEMOLISHED.

SOLID/BOLD LINED ELECTRICAL DEVICES INDICATE DEVICES THAT ARE NEW.

SCREENED/LIGHT LINED ELECTRICAL DEVICES INDICATE DEVICES THAT ARE EXISTING TO

REMAIN AND ARE SHOWN FOR REFERENCE ONLY.

H. WALLS, CEILINGS, AND GENERAL MATERIALS SHALL BE DEMOLISHED BY

GENERAL/DEMOLITION CONTRACTOR. DEMOLISH ELECTRICAL LUMINAIRES, DEVICES, AND

EQUIPMENT PRIOR TO REMOVAL OF WALLS AND CEILINGS. RELOCATE SYSTEMS AS

INDICATED ON DRAWINGS OR AS REQUIRED FOR INSTALLATION OF NEW WALLS OR

CEILINGS. COORDINATE WITH STRUCTURAL INSTALLATION, ARCHITECTURAL,

MECHANICAL, AND OTHER TRADES. PROVIDE TEMPORARY LIGHTING AND POWER FOR

ELECTRICAL ITEMS IN THE VARIOUS AREAS OF CONSTRUCTION.

I. LUMINAIRES THAT ARE DESIGNATED FOR REUSE SHALL BE CLEANED AND REINSTALLED.

J. EXISTING CONDUIT HOLES OR SLEEVES INSTALLED IN CONCRETE FLOORS OR WALLS

THAT ARE ABANDONED AFTER DEMOLITION SHALL HAVE CONDUIT REMOVED AND HOLES

FILLED AND PATCHED. PROVIDE PATCHING AND PAINTING AS REQUIRED. SEE

ARCHITECTURAL TYPICAL DETAIL.

K. COORDINATE THE DEMOLITION OF LUMINAIRES, DEVICES, AND EQUIPMENT WITH OTHER

CONTRACTORS. DEMOLISH POWER, FIRE ALARM, ELECTRICAL CONTROLS, AND

INSTRUMENTATION WIRING OF EQUIPMENT BEING DEMOLISHED. RELOCATE, EXTEND, AND

RECONNECT POWER, FIRE ALARM, ELECTRICAL CONTROLS, AND INSTRUMENTATION

WIRING OF EQUIPMENT BEING RELOCATED. COORDINATE REMOVAL AND RELOCATION OF

POWER AND CONTROLS OF MECHANICAL EQUIPMENT WITH RESPECTIVE CONTRACTORS.

L. VERIFY EXISTING CONDITIONS BEFORE COMMENCING DEMOLITION OF AN AREA. WHERE

NEEDED DURING CONSTRUCTION FOR PHASING, TEMPORARILY RECONNECT CIRCUITS

AND DEVICES AFTER DEMOLITION UNTIL PERMANENT INSTALLATION IS COMPLETED.

DEMOLISH AFTER INSTALLATION IS COMPLETED.

M. COORDINATE DEMOLITION OF EXISTING WALLS, CEILINGS AND FLOORS WITH DEMOLITION

CONTRACTOR.

N. SEAL OPENINGS IN BOXES AND ENCLOSURES THAT HAVE CONDUIT REMOVED AND

OPENINGS THAT ARE NOT REUSED. PROVIDE BLANK COVER PLATES ON ALL JUNCTION

BOXES AND ENCLOSURES THAT HAVE DEVICES DEMOLISHED BUT BOXES ARE EXISTING

TO REMAIN.

O. PROVIDE MULTI-POLE CIRCUIT BREAKER(S) OR REPLACE WIRING WITH DEDICATED

NEUTRALS WHERE EXISTING MULTI-WIRE CIRCUITS ARE MODIFIED.

P. DEMOLISH ALL ELECTRICAL DEVICES AND BOXES AS NECESSARY WHERE NEW WALL

CONSTRUCTION WILL INTERSECT AN EXISTING WALL.

Q. DEMOLISH ALL EQUIPMENT IN A MANNER THAT WILL NOT DESTROY OR DAMAGE

EQUIPMENT OR DEVICES THAT ARE TO BE SALVAGED, EXISTING TO REMAIN, OR BE

RELOCATED.

R. REPLACE ALL CONDUITS AND RACEWAYS THAT ARE DAMAGED DURING CONSTRUCTION.

S. DEMOLISH OR RELOCATE LIGHTING CONTROLS, EXIT SIGNAGE, AND ACCESS CONTROLS

AS NECESSARY TO ACCOMMODATE NEW DOOR CONFIGURATIONS.

T. PROVIDE CONDUIT AND COMMUNICATIONS/DATA CABLING AS NECESSARY FOR A

COMPLETE CABLING SYSTEM TO DEVICE LOCATIONS EXISTING TO REMAIN AFTER

DEMOLITION.

U. DO NOT REUSE MATERIALS (CONDUIT, CABLING, WIRING, DEVICES, SUPPORTS,

EQUIPMENT, ETC...) UNLESS SPECIFICALLY INDICATED OR APPROVED BY THE ENGINEER.

ALL CONDUIT, PATHWAYS, AND WIRING SHALL BE NEW UNLESS SPECIFICALLY INDICATED

AS "EXISTING TO REMAIN" OR "EXISTING TO BE REUSED".

V. DUE TO DEMOLITION AND REMODELING, ELECTRICAL CONTRACTOR SHALL CONSIDER

MINOR CIRCUIT MODIFICATIONS AND REROUTING AS INCLUDED IN THE SCOPE. MAJOR

CONCEALED CONDITIONS IN WHICH THE CONTRACTOR COULD NOT ANTICIPATE THE

EFFORT LEVEL REQUIRED SHALL BE BROUGHT PROMPTLY TO THE ENGINEER’S

ATTENTION. IF THE CONTRACTOR WILL REQUEST A CHANGE IN THE CONTRACT AMOUNT

OR CONTRACT TIME DUE TO CONDITION, THEN THE CONTRACTOR SHALL SUBMIT DIGITAL

PHOTOGRAPHS OF THE EXISTING CONDITIONS WITH A PROPOSED RESOLUTION. FAILURE

TO DO SO IMPLIES THE CONTRACTOR HAS ASSUMED THE WORK EFFORT TO BE INCLUDED

IN THEIR BID. ENGINEER WILL PROMPTLY REVIEW INFORMATION AND MAKE

RECOMMENDATIONS TO THE OWNER IN AN ATTEMPT TO MAINTAIN CONSTRUCTION

SCHEDULE.

GENERAL FIRE ALARM PLAN NOTES

A. INSTALL ELECTRICAL WORK IN ACCORDANCE WITH THE REQUIREMENTS OF THE LATEST

ADOPTED EDITION OF THE NATIONAL ELECTRICAL CODE, STATE, COUNTY, MUNICIPAL AND

FEDERAL LAWS AND ORDINANCES GOVERNING THE PROJECT. IF THE PLANS AND

SPECIFICATIONS ARE IN DIRECT CONFLICT WITH SUCH CODES, LAWS OR ORDINANCES,

NOTIFY THE ENGINEER OF CONFLICT IN WRITING PRIOR TO MAKING CHANGES FROM

PLANS AND/OR SPECIFICATIONS. WORK SHALL BE PERFORMED UNDER THE SUPERVISION

OF A LICENSED MASTER ELECTRICIAN, LICENSED IN THE STATE IN WHICH THE WORK WILL

OCCUR.

B. BRANCH CIRCUIT CONDUITS, JUNCTION BOXES AND CONNECTIONS ARE NOT SHOWN.

PROVIDE COMPLETE RACEWAY SYSTEM AND CONDUCTORS AS REQUIRED FOR THE

INDICATED CIRCUITRY.

C. ALTHOUGH FEEDER AND BRANCH CIRCUIT WIRING AND CONDUIT ARE NOT SPECIFICALLY

SHOWN, PROVIDE A COMPLETE FEEDER AND BRANCH CIRCUIT WIRING SYSTEM.

D. HOMERUN CIRCUITS SHALL BE 0.75 INCH CONDUIT, 2#12, 1#12 GROUND MINIMUM TO A

20A/1P CIRCUIT BREAKER IN DESIGNATED PANEL. THE NUMBERS SHOWN AT EACH

DEVICE/HOMERUN REPRESENT BRANCH CIRCUIT NUMBER(S) IN PANELBOARD.

E. EXTERIOR LUMINAIRE/DEVICE CIRCUITS SHALL BE 0.75 INCH CONDUIT, 2#10, 1#10 GROUND

MINIMUM TO 20A/1P CIRCUIT BREAKER IN DESIGNATED PANEL. THE NUMBERS SHOWN AT

EACH DEVICE REPRESENT BRANCH CIRCUIT NUMBER(S) IN PANELBOARD.

F. ALL CONDUIT AND WIRING SIZES SHOWN ARE MINIMUMS, DEPENDING ON EXACT ROUTING,

PROVIDE LARGER AS REQUIRED FOR VOLTAGE DROP, AMBIENT TEMPERATURE, OR

OTHER DERATING.

G. WIRE AND RACEWAY SIZES INDICATED ON HOMERUNS/CIRCUITS SHALL BE CONTINUOUS

FOR ENTIRE LENGTH.

H. A MAXIMUM OF THREE CIRCUITS SHALL BE INSTALLED IN A CONDUIT.

I. PROVIDE DEDICATED NEUTRAL FOR EACH SINGLE PHASE CIRCUIT.

J. RACEWAYS SHALL BE LIMITED TO SIX CURRENT CARRYING CONDUCTORS (THREE PHASE

AND THREE NEUTRALS) AND GROUNDING CONDUCTOR.

K. CONDUCTORS MUST BE DERATED PER THE NATIONAL ELECTRICAL CODE WHEN MORE

THAN THREE CURRENT CARRYING CONDUCTORS ARE RUN IN THE SAME RACEWAY.

L. INSTALL WIRING CONCEALED IN RACEWAYS AND CONCEAL RACEWAYS IN WALLS, FLOORS,

AND CEILINGS. NO SURFACE RACEWAYS SHALL BE INSTALLED ON NEW FINISHED WALLS.

M. CABLING THAT IS NOT IN CONDUIT AND IS LOCATED IN AIR HANDLING PLENUM SHALL BE

PLENUM RATED. REFER TO MECHANICAL PLANS FOR PLENUM AREAS.

N. DO NOT INSTALL ELECTRICAL EQUIPMENT THAT PHYSICALLY INTERFERES WITH

SERVICING OF MECHANICAL EQUIPMENT.

O. ELECTRICAL CONDUITS, WIRING, BOXES, ETC. SHALL NOT PENETRATE STAIR ENCLOSURE

UNLESS THEY ARE FEEDING DEVICES LOCATED WITHIN THE STAIR ENCLOSURE.

P. PROVIDE ELECTRICAL OUTLET PLATE GASKET SEALS AT RECEPTACLES, SWITCHES,

OTHER ELECTRICAL BOXES ON EXTERIOR WALLS AND INTERIOR WALLS BETWEEN

CONDITIONED AND UNCONDITIONED SPACES.

Q. PROVIDE UNIVERSAL BLANK PLUGS ON SPARE CONDUITS SIZED FOR CONDUIT.

R. SEAL CONDUITS AT THE LAST STRUCTURE PRIOR TO CONDUITS ENTERING A BUILDING

AND WHERE CONDUITS ENTER A BUILDING. INSTALL NYLON PULL STRING AND FOOTAGE

TAPE IN SPARE CONDUITS.

S. RACEWAY AND WIRING INDICATED ON THE DRAWINGS ARE RECOMMENDATIONS FOR

SPECIFIC ROUTES OR SPECIAL CONDITIONS. CONTRACTOR IS RESPONSIBLE FOR EXACT

ROUTING.

T. 120 VOLT BRANCH CIRCUITS OVER 100 FEET IN CONDUCTOR LENGTH SHALL BE

INCREASED ONE WIRE SIZE OVER CIRCUIT AMPACITY AND CIRCUITS OVER 170 FEET IN

CONDUCTOR LENGTH SHALL BE INCREASED TWO WIRE SIZES.

U. 277 VOLT BRANCH CIRCUITS OVER 230 FEET IN CONDUCTOR LENGTH SHALL BE

INCREASED ONE WIRE SIZE OVER CIRCUIT AMPACITY AND CIRCUITS OVER 380 FEET IN

CONDUCTOR LENGTH SHALL BE INCREASED TWO WIRE SIZES.

V. ELEVATIONS AND HEIGHTS ON ELECTRICAL DRAWINGS AND SPECIFICATIONS ARE

APPROXIMATE. FOR WALL MOUNTED DEVICES REFER TO ARCHITECTURAL ELEVATIONS.

FOR LOCATION OF CEILING MOUNTED DEVICES REFER TO ARCHITECTURAL REFLECTED

CEILING PLAN.

W. REFERENCES TO MECHANICAL INDICATES DIVISIONS 21, 22, 23, & 25 CONTRACTORS.

REFERENCES TO ELECTRICAL INDICATES DIVISIONS 26, 27 & 28 CONTRACTORS.

X. PAINT CONDUIT AND BOXES WHERE CONDUIT OR BOXES ARE VISIBLE IN FINISHED

SPACES. COORDINATE WITH OTHER TRADES.

Y. PROVIDE NEW, FIRST QUALITY MATERIAL FOR ALL PRODUCTS PROVIDED UNDER THIS

CONTRACT.

Z. DO NOT INSTALL OUTLETS BACK TO BACK. PROVIDE MINIMUM OF 24 INCH HORIZONTAL

SPACING IN FIRE RATED WALLS. MOUNT LOW VOLTAGE AND POWER OUTLETS IN

DIFFERENT STUD WALL CAVITIES. PROVIDE PUTTY PADS AT EACH BOX WHERE A

JUNCTION BOX OR OUTLET IS INSTALLED WITHIN THE SAME STUD WALL CAVITY AS

ANOTHER OUTLET OR JUNCTION BOX ON THE OTHER SIDE OF THE WALL. PROVIDE PUTTY

PADS WHERE REQUIRED TO MAINTAIN THE FIRE RATING OR THE SOUND TRANSMISSION

LEVEL OF THE WALL OR FINISH.

R P

S T

NENIS O LA

E L

I C N S

D R

WILLIAM P.

22074

WILSON

OF KE

NOTE:

IT IS NOT INTENDED THAT THE PLANS SHOW ALL OFFSETS IN PIPES, CONDUITS, SPRINKLERS, AND DEVICE LOCATIONS REQUIRED FOR INSTALLATION OF THE WORK. IT SHALL BE THE RESPONSIBILITY OF THE CONTRACTOR AND SUB-CONTRACTORS TO COORDINATE INSTALLATION OF THE WORK AND TO PROVIDE THE NECESSARY OFFSETS, TRANSFORMATIONS, AND FITTINGS REQUIRED. NO ADDITIONAL COMPENSATION WILL BE ALLOWED FOR CORRECTION CONFLICTS BETWEEN THE WORK OF VARIOUS TRADES. DETAILS AND SECTIONS ARE SHOWN FOR THE CONTRACTORS CONVENIENCE AND SHALL NOT BE CONSIDERED COMPLETE IN EVERY DETAIL.

REVISION HISTORY OF THIS DRAWING

DRAWING NO.

AS-BUILT DATE

DECA LOG #

DESCRIPTION OF REVISIONS DATE DESCRIPTION OF REVISIONS DATE

DRAWING INFORMATION

A & E FILE NO.

DRAWING DATE

DRAWN BY

CHECKED BY

PHASE

RTA DATE

COMMONWEALTH OF KENTUCKY

FINANCE AND ADMINISTRATION CABINET

DEPARTMENT FOR FACILITIES AND SUPPORT SERVICES

DIVISION OF ENGINEERING AND CONTRACT ADMINISTRATION

FRANKFORT, KENTUCKY

ACCOUNT NO.

06/21/23

470CAP5SS6800WPW

22-0864.00

06/21/23

EFN

FIRE ALARM GENERAL NOTES - SITE PLAN - SYMBOLS

FA000

RTA

KCTCS LIFE SAFETY UPGRADE - BID PACKAGE #1

SOMERSET COMMUNITY & TECHNICAL COLLEGE

ELECTRICAL SYMBOLS LEGEND NOTES:

1. THESE SYMBOLS COMPRISE A STANDARD LIST, NOT ALL SYMBOLS

MAY APPEAR ON THESE DRAWINGS.

2. MOUNTING HEIGHTS INDICATED ARE FOR STUD WALL

CONSTRUCTION. WHEN BLOCK OR BRICK CONSTRUCTION IS USED,

ADJUST MOUNTING HEIGHTS TO ALIGN DEVICE PLATES WITH

RUNNING JOINT.

3. MOUNTING HEIGHTS ARE TO CENTER OF DEVICE ABOVE FINISHED

FLOOR UNLESS NOTED OTHERWISE. MOUNTING HEIGHTS

INDICATED ON ARCHITECTURAL WALL ELEVATIONS OR AS NOTED

SPECIFICALLY ON THE DRAWINGS

4. SHALL TAKE PRECEDENCE OVER MOUNTING HEIGHTS LISTED.

5. PROVDE 4-11/16" SQUARE BOX WITH SINGLE DEVICE MUD RING AND

1"C MINIMUM STUBBED INTO ACCESSIBLE CEILING SPACE AS

REQUIRED FOR ROUGH-IN OF LOW VOLTAGE/ TECHNOLOGY

SYSTEM OUTLET LOCATIONS.

6. PROVIDE 4-11/16" SQUARE BOX WITH 1.25" MINIMUM STUBBED INTO

ACCESSIBLE CEILING SPACE FOR ALL AUDIO-VIDEO OUTLETS AND

DEVICES.

7. REFER TO CONSTRUCTION DRAWINGS AND SCHEDULES FOR

ADDITIONAL INFORMATION.

1 ADDENDUM 01 08.08.23

OFFICE

COPIER

OFFICE

102A

CLASSROOM

OFFICE

STORAGE

OFFICE

STORAGE

OFFICE

LOUNGE

107A

CLASSROOM

115A

STORAGE

115B

113A

STORAGE

LOBBY

SERVER ROOM

MAILROOM

115B

CONFERENCE

COPIER

OFFICE

117B

OFFICE

117A

117C

117D

OFFICE

116A

STORAGE

116B

LOBBY

POWER PLANT SYSTEMS

POWER PLANT

AIRFRAME SYSTEMS

AIRFRAME STRUCTURES

RELATED INSTRUCTION

CORR.

HANGAR

143A 143B

FABRICATION

ENGINE SHOP

147A

STORAGE

TOOLROOM

JAN.

RESTROOM

A/P RESOURCE

CORR.

OFFICE

185A

185B

185D

179E

FLUID POWER

WELDING

179F

VENDING

RESTROOM

CORR.

MECHANICAL

STORAGE

166B

KITCHEN

166C

INDUSTRY CLASSROOM

WELDING 2

INDUSTRY TRAINING

159B

159C

CLASSROOM

153J

INDUSTRY TRAINING

OFFICE

153D

159D

153A

AUTO TECH

BODY SHOP

CLASSROOM

187A

187C

PAINT BOOTH

188D

CLASSROOM

188A

187B

188B

188C

BOOTH

WELDING

BOOTH

WELDING

BOOTH

WELDING

BOOTH

WELDING

BOOTH

WELDING

BOOTH

WELDING

BOOTH

WELDING

BOOTH

WELDING

BOOTH

WELDING

BOOTH

WELDING

BOOTH

WELDING

BOOTH

LOCKERS

GRINDING

BOOTH

GRINDING

BOOTH

GRINDING

BOOTH

TOOL TOOL

Garage Door

Test Cell

MACHINE ROOM

LOCKERS LOCKERS LOCKERS

F H

F H F H

F H

F H F H

F F

F H

F F

FF FFAAPF

F F

F H F H F H

F H

F H F H F H

F S

F F

F H

F F

F H

F HF F

F H

F F F

F H

F F

F H F H

F S

F F F

F T

F S

F F

F H

F F

F H

F F

F FF F

F H

F H F H

F H

F T

S F

T S

F T

S F

F S

F F

2 2

2 2 2

2 2

2 2 2

2 2

R P

S T

NENIS O LA

E L

I C N S

D R

WILLIAM P.

22074

WILSON

OF KE

NOTE:

REVISION HISTORY OF THIS DRAWING

DRAWING NO.

AS-BUILT DATE

DECA LOG #

DESCRIPTION OF REVISIONS DATE DESCRIPTION OF REVISIONS DATE

DRAWING INFORMATION

A & E FILE NO.

DRAWING DATE

DRAWN BY

CHECKED BY

PHASE

RTA DATE

COMMONWEALTH OF KENTUCKY

FINANCE AND ADMINISTRATION CABINET

DEPARTMENT FOR FACILITIES AND SUPPORT SERVICES

DIVISION OF ENGINEERING AND CONTRACT ADMINISTRATION

FRANKFORT, KENTUCKY

ACCOUNT NO.

06/21/23

470CAP5SS6800WPW

22-0864.00

06/21/23

EFN

BUILDING 1 FIRE ALARM DEMOLITION - LEVEL 1

S1-FA110

RTA

KCTCS LIFE SAFETY UPGRADE - BID PACKAGE #1

SOMERSET COMMUNITY & TECHNICAL COLLEGE

1/16" = 1'-0"S1-FA110

1 LEVEL 1 FIRE ALARM DEMOLITION PLAN - SOUTH BUILDING 1

GENERAL NOTES - DEMOLITION

A. COORDINATE PHASING OF SCOPE WITH GENERAL CONTRACTOR. COORDINATE DEMOLITION OF FIRE ALARM SYSTEM COMPONENTS

WITH OTHER TRADES.

B. COORDINATE ALL FIRE ALARM SHUT-DOWNS WITH OWNER PRIOR TO EXECUTION OF WORK. COORDINATE WITH GENERAL CONTRACTOR AND FACILITY STAFF TO PROVIDE A FIRE WATCH IN ACCORDANCE TO NFPA 101. NOTIFY AUTHORITY HAVING

JURISDICTION OF ALL PLANNED FIRE ALARM SHUT-DOWNS.

C. ALL EXISTING FIRE ALARM CONDUIT AND PENETRATIONS TO REMAIN IN PLACE FOR RE-USE. EXISTING FIBER TO EXISTING FIRE ALARM CONTROL PANELS TO REMAIN IN PLACE FOR RE-TERMINATION TO REPLACEMENT PANEL. REMOVE ALL FIRE ALARM CABLING FOR INITIATION AND ANNUNCIATION CIRCUITS BETWEEN EXISTING FIRE ALARM CONTROL PANEL AND DEVICES.

D. COORDINATE WITH GENERAL CONTRACTOR TO DISCONNECT, STORE, AND RE-INSTALL ALL ELECTRICAL DEVICES MOUNTED IN

CEILINGS TO BE REMOVED TO INSTALL NEW SPRINKLER PIPING.

E. FURNISH AND INSTALL CONDUIT AND WIRE AS NECESSARY FOR CONTINUITY OF ANY FEEDERS OR BRANCH CIRCUITS ORIGINATING OUTSIDE THE DEMOLITION AREA THAT SERVES ANY ELECTRICAL EQUIPMENT OR DEVICES TO REMAIN AFTER DEMOLITION. MODIFY

OR REPLACE AS REQUIRED.

F. FURNISH AND INSTALL CONDUIT AND/OR COMMUNICATIONS/DATA WIRING AS NECESSARY FOR CONTINUITY OF ANY WIRING ORIGINATING OUTSIDE THE DEMOLITION AREA THAT SERVES ANY COMMUNICATIONS/DATA EQUIPMENT OR DEVICES TO REMAIN

AFTER DEMOLITION. MODIFY OR REPLACE AS REQUIRED.

G. FURNISH AND INSTALL BLANK COVER PLATES OVER ALL EXISTING UNUSED OPENINGS.

KEYNOTES

1 DISCONNECT AND REMOVE EXISTING FACP AND ACCESSORY CABINETS. EXISTING 120V CIRCUIT AND BRANCH CONDUITS TO

REMAIN IN PLACE FOR RECONNECTION TO REPLACEMENT FACP.

2 DISCONNECT AND REMOVE EXISTING FIRE ALARM DEVICE. REMOVE ALL CABLING BACK TO SOURCE. EXISTING DEVICE

BACKBOX AND CONDUIT TO REMAIN IN PLACE.

3 DISCONNECT AND REMOVE EXISTING ANNUNCIATOR PANEL. REMOVE ALL CABLING BACK TO SOURCE. CONDUIT AND BACKBOX

TO REMAIN IN PLACE.

4 DISCONNECT AND REMOVE EXISTING FLOW AND TAMPER SWITCHES. TAMPER SWITCHES INTEGRAL TO VALVES ARE TO REMAIN AND INTEGRATED TO NEW FIRE ALARM SYSTEM. REMOVE FLEX CONDUIT BACK TO NEAREST JUNCTION BOX. REMOVE ALL

CABLING BACK TO SOURCE.

6 DISCONNECT AND REMOVE EXISTING AIR HANDLER SMOKE DETECTOR. REMOVE ALL CABLING BACK TO SOURCE. REMOVE FLEX CONDUIT BACK TO NEAREST FIRE ALARM JUNCTION BOX. EXISTING CONDUIT TO REMAIN IN PLACE FOR REUSE.

7 EXISTING POWER AND FIRE ALARM CONDUIT TO BUILDING 4. SEE S4-FA110 FOR CONTINUATION.

1 ADDENDUM 01 08.08.23

OFFICE

COPIER

OFFICE

102A

CLASSROOM

OFFICE

STORAGE

OFFICE

STORAGE

OFFICE

LOUNGE

107A

CLASSROOM

115A

STORAGE

115B

113A

STORAGE

LOBBY

SERVER ROOM

MAILROOM

115B

CONFERENCE

COPIER

OFFICE

117B

OFFICE

117A

117C

117D

OFFICE

116A

STORAGE

116B

LOBBY

POWER PLANT SYSTEMS

POWER PLANT

AIRFRAME SYSTEMS

AIRFRAME STRUCTURES

RELATED INSTRUCTION

CORR.

HANGAR

143A 143B

FABRICATION

ENGINE SHOP

147A

STORAGE

TOOLROOM

JAN.

RESTROOM

A/P RESOURCE

CORR.

OFFICE

185A

185B

185D

179E

FLUID POWER

WELDING

179F

VENDING

RESTROOM

CORR.

MECHANICAL

STORAGE

166B

KITCHEN

166C

INDUSTRY CLASSROOM

WELDING 2

INDUSTRY TRAINING

159B

159C

CLASSROOM

153J

INDUSTRY TRAINING

OFFICE

153D

159D

153A

AUTO TECH

BODY SHOP

CLASSROOM

187A

187C

PAINT BOOTH

188D

CLASSROOM

188A

187B

188B

188C

BOOTH

WELDING

BOOTH

WELDING

BOOTH

WELDING

BOOTH

WELDING

BOOTH

WELDING

BOOTH

WELDING

BOOTH

WELDING

BOOTH

WELDING

BOOTH

WELDING

BOOTH

WELDING

BOOTH

WELDING

BOOTH

LOCKERS

GRINDING

BOOTH

GRINDING

BOOTH

GRINDING

BOOTH

TOOL TOOL

Garage Door

Test Cell

MACHINE ROOM

LOCKERS LOCKERS LOCKERS

F T

F H

F H F H

F H

F H F H

F F

F H

F F

FF FFAAPF

F F

F H F H F H

F H

F H F H F H

F S

F F

F H

F F

F H

F HF F

F H

F F F

F H

F F

F H F H

F S

F F

F H

F F

F H

F F

F FF F

F H

F H F H F H

F F

F FF

F H

F T

F F

F T

S F

T S

F F

S F

F S

E3 E2

E11

E12

E13

R P

S T

NENIS O LA

E L

I C N S

D R

WILLIAM P.

22074

WILSON

OF KE

NOTE:

REVISION HISTORY OF THIS DRAWING

DRAWING NO.

AS-BUILT DATE

DECA LOG #

DESCRIPTION OF REVISIONS DATE DESCRIPTION OF REVISIONS DATE

DRAWING INFORMATION

A & E FILE NO.

DRAWING DATE

DRAWN BY

CHECKED BY

PHASE

RTA DATE

COMMONWEALTH OF KENTUCKY

FINANCE AND ADMINISTRATION CABINET

DEPARTMENT FOR FACILITIES AND SUPPORT SERVICES

DIVISION OF ENGINEERING AND CONTRACT ADMINISTRATION

FRANKFORT, KENTUCKY

ACCOUNT NO.

06/21/23

470CAP5SS6800WPW

22-0864.00

06/21/23

EFN

BUILDING 1 FIRE ALARM - LEVEL 1

S1-FA210

RTA

KCTCS LIFE SAFETY UPGRADE - BID PACKAGE #1

SOMERSET COMMUNITY & TECHNICAL COLLEGE

1/16" = 1'-0"S1-FA210

1 LEVEL 1 FIRE ALARM PLAN - SOUTH BUILDING 1

KEYNOTES

E1 PROVIDE NEW FACP CONTROL PANEL IN EXISTING LOCATION. WIRE FACP TO EXISTING 120V CIRCUIT SERVING FIRE ALARM PANEL MADE AVAILABLE DURING DEMOLITION. REPLACE EXISTING 20A BREAKER SERVING FACP WITH NEW DEVICE WITH RED DEVICE WITH CLEAR PERMANENT INDICATION OF FIRE ALARM CIRCUIT IN ACCORDANCE WITH NEC ARTICLE 760.121(B) AND NFPA 72 ARTICLE 10.6.5.2. PROVIDE CAT6 CABLE FROM SYSTEM DIALER TO BUILDING TELECOMMUNICATIONS NETWORK AT

LOCATION INDICATED ON PLAN.

E2 PROVIDE NEW FIRE ALARM ANNUNCIATOR AS SHOWN. PROVIDE NEW CONDUIT FROM NEAREST EXISTING FIRE ALARM JUNCTION BOX. EXTEND NEAREST ANNUNCIATOR CIRCUIT TO NEW LOCATION. PROVIDE CLASS B WIRING TO NEW DEVICE.

E3 PROVIDE NEW FIRE ALARM INITIATION DEVICE AS SHOWN. PROVIDE NEW CONDUIT FROM NEAREST EXISTING FIRE ALARM JUNCTION BOX. EXTEND NEAREST ANNUNCIATOR CIRCUIT TO NEW LOCATION. PROVIDE CLASS B WIRING TO NEW DEVICE.

E6 PROVIDE NEW EMERGENCY VOICE EVACUATION EQUIPMENT PANEL AND CONNECT TO FACP.

E7 UTLIZE EXISTING PATHWAY TO ROUTE NEW FIRE ALARM CABLING TO INSTRUCTION SPACES 187 AND 188.

E8 EXISTING POWER AND FIRE ALARM CONDUITS TO BUILDING 4. REFER TO SHEET S4-FA210 FOR CONTINUATION.

E11 PROVIDE REMOTE MICROPHONE UNIT IN LOCKABLE SURFACE MOUNTED CABINET. CONNECT TO EMERGENCY VOICE

EVACUATION EQUIPMENT PANEL LOCATED IN MECH

E12 LOCATION OF EXISTING BUILDING TELECOMMUNICATIONS ROOM. PROVIDE CAT6 CABLING FROM NEW FACP TO EXISTING AVAILABLE PORT ON EXISTING PATCH PANEL. COORDINATE INSTALLATION AND PROGRAMMING WITH OWNER.

E13 CONNECT EXISTING FLOW SWITCHES TO NEW FIRE ALARM SYSTEM. PROVIDE ADDRESSABLE FIRE ALARM MODULES AS REQUIRED TO INTERFACE WITH NEW FIRE ALARM SYSTEM. MOUNT MODULE TO SURFACE MOUNTED BOX NEAR DEVICE.

PROVIDE CABLING BACK TO FACP.

GENERAL NOTES - FIRE ALARM

A. ALL NEW FIRE ALARM DEVICES SHOWN ARE TO BE INSTALLED IN EXISTING DEVICE BACKBOX OF DEVICES REMOVED IN DEMOLITION, UNLESS NOTED OTHERWISE. REUSE EXISTING CONDUIT AND JUNCTION BOXES FOR NEW CLASS B FIRE ALARM CABLING. INSTALL ALL NEW DEVICES PER NFPA 72 REQUIREMENTS. EXTEND CONDUIT AND CABLING AS REQUIRED FOR CODE COMPLIANT INSTALLATION. PROVIDE ALL CONDUIT, SURFACE RACEWAY, CABLING, AND ACCESSORIES AS

REQUIRED.

B. ELECTRICAL CONTRACTOR SHALL BE RESPONSIBLE FOR WIRING ALL ELECTRICAL ITEMS SHOWN ON THE DRAWINGS, EXCEPT ITEMS LISTED ON SHEET E0.01 GENERAL ELECTRICAL NOTES.

C. INSTALL CONDUIT WITH NO MORE THAN (2) 90° BENDS BETWEEN PULL BOXES, AND NO MORE THAN 100'-0" BETWEEN PULL

BOXES. PULL BOXES SHALL BE INSTALLED FOR STRAIGHT THRU PULLS ONLY.

D. ALL FIRE ALARM AND ACCESS CONTROL CABLES SHALL BE INSTALLED IN CONDUIT.

1 ADDENDUM 01 08.08.23

ACT

STORAGE

8’−2"

EXP

TOOL RM

EXP

ELECTRIC RM

EXP

TRANSMISSION RM

ACT

DIESEL CLASSROOM

9’−0"

ACT

OFFICE

9’−0"

ACT

COMPUTER LAB

9’−0"

EXP

DIESEL GARAGE

GYP

501C

7’−11"

GYP

501D

7’−9"

8’−9"

GYP

7’−9"

GYP

LOCKERS

F H F H

F H

F F

F F H

F S

F H F H

2 2

1/8" = 1'-0"S5-FA110

1 LEVEL 1 FIRE ALARM DEMOLITION PLAN - SOUTH BUILDING 5

R P

S T

NENIS O LA

E L

I C N S

D R

WILLIAM P.

22074

WILSON

OF KE

NOTE:

REVISION HISTORY OF THIS DRAWING

DRAWING NO.

AS-BUILT DATE

DECA LOG #

DESCRIPTION OF REVISIONS DATE DESCRIPTION OF REVISIONS DATE

DRAWING INFORMATION

A & E FILE NO.

DRAWING DATE

DRAWN BY

CHECKED BY

PHASE

RTA DATE

COMMONWEALTH OF KENTUCKY

FINANCE AND ADMINISTRATION CABINET

DEPARTMENT FOR FACILITIES AND SUPPORT SERVICES

DIVISION OF ENGINEERING AND CONTRACT ADMINISTRATION

FRANKFORT, KENTUCKY

ACCOUNT NO.

06/21/23

470CAP5SS6800WPW

22-0864.00

06/21/23

EFN

BUILDING 5 FIRE ALARM DEMOLITION - LEVEL 1

S5-FA110

RTA

KCTCS LIFE SAFETY UPGRADE - BID PACKAGE #1

SOMERSET COMMUNITY & TECHNICAL COLLEGE

GENERAL NOTES - DEMOLITION

A. COORDINATE PHASING OF SCOPE WITH GENERAL CONTRACTOR. COORDINATE DEMOLITION OF FIRE ALARM SYSTEM COMPONENTS

WITH OTHER TRADES.

JURISDICTION OF ALL PLANNED FIRE ALARM SHUT-DOWNS.

D. COORDINATE WITH GENERAL CONTRACTOR TO DISCONNECT, STORE, AND RE-INSTALL ALL ELECTRICAL DEVICES MOUNTED IN

CEILINGS TO BE REMOVED TO INSTALL NEW SPRINKLER PIPING.

OR REPLACE AS REQUIRED.

AFTER DEMOLITION. MODIFY OR REPLACE AS REQUIRED.

G. FURNISH AND INSTALL BLANK COVER PLATES OVER ALL EXISTING UNUSED OPENINGS.

KEYNOTES

1 DISCONNECT AND REMOVE EXISTING FACP AND ACCESSORY CABINETS. EXISTING 120V CIRCUIT AND BRANCH CONDUITS TO

REMAIN IN PLACE FOR RECONNECTION TO REPLACEMENT FACP.

2 DISCONNECT AND REMOVE EXISTING FIRE ALARM DEVICE. REMOVE ALL CABLING BACK TO SOURCE. EXISTING DEVICE

BACKBOX AND CONDUIT TO REMAIN IN PLACE.

ACT

STORAGE

8’−2"

EXP

TOOL RM

EXP

ELECTRIC RM

EXP

TRANSMISSION RM

ACT

DIESEL CLASSROOM

9’−0"

ACT

OFFICE

9’−0"

ACT

COMPUTER LAB

9’−0"

EXP

DIESEL GARAGE

GYP

501C

7’−11"

GYP

501D

7’−9"

8’−9"

GYP

7’−9"

GYP

LOCKERS

F H F H

F H

F F

F F H

F S

F F

F T

F H F H

E10

1/8" = 1'-0"S5-FA210

1 LEVEL 1 FIRE ALARM PLAN - SOUTH BUILDING 5

R P

S T

NENIS O LA

E L

I C N S

D R

WILLIAM P.

22074

WILSON

OF KE

NOTE:

REVISION HISTORY OF THIS DRAWING

DRAWING NO.

AS-BUILT DATE

DECA LOG #

DESCRIPTION OF REVISIONS DATE DESCRIPTION OF REVISIONS DATE

DRAWING INFORMATION

A & E FILE NO.

DRAWING DATE

DRAWN BY

CHECKED BY

PHASE

RTA DATE

COMMONWEALTH OF KENTUCKY

FINANCE AND ADMINISTRATION CABINET

DEPARTMENT FOR FACILITIES AND SUPPORT SERVICES

DIVISION OF ENGINEERING AND CONTRACT ADMINISTRATION

FRANKFORT, KENTUCKY

ACCOUNT NO.

06/21/23

470CAP5SS6800WPW

22-0864.00

06/21/23

EFN

BUILDING 5 FIRE ALARM - LEVEL 1

S5-FA210

RTA

KCTCS LIFE SAFETY UPGRADE - BID PACKAGE #1

SOMERSET COMMUNITY & TECHNICAL COLLEGE

GENERAL NOTES - FIRE ALARM

REQUIRED.

B. ELECTRICAL CONTRACTOR SHALL BE RESPONSIBLE FOR WIRING ALL ELECTRICAL ITEMS SHOWN ON THE DRAWINGS, EXCEPT ITEMS LISTED ON SHEET E0.01 GENERAL ELECTRICAL NOTES.

C. INSTALL CONDUIT WITH NO MORE THAN (2) 90° BENDS BETWEEN PULL BOXES, AND NO MORE THAN 100'-0" BETWEEN PULL

BOXES. PULL BOXES SHALL BE INSTALLED FOR STRAIGHT THRU PULLS ONLY.

D. ALL FIRE ALARM AND ACCESS CONTROL CABLES SHALL BE INSTALLED IN CONDUIT.

KEYNOTES

LOCATION INDICATED ON PLAN.

E4 PROVIDE CONNECTIONS TO FLOW AND TAMPER SWITCHES FOR NEW SPRINKLER SERVICE ENTRANCE. REFER TO FIRE

PROTECTION DRAWINGS FOR EXACT LOCATION.

E5 PROVIDE NEW FIRE SPRINKLER HORN AND TIE IN TO REPLACEMENT FIRE ALARM SYSTEM. COMPLY WITH ALL REQUIREMENTS

OF NFPA 13 AND NFPA 72.

E10 PROVIDE BONDING JUMPER TO NEW SPRINKLER PIPING SYSTEM. CONNECT TO EXISTING BUILDING GROUNDING SYSTEM AT NEAREST AVAILABLE POINT IN COMPLIANCE WITH NEC. REFER TO SPECIFICATIONS FOR ADDITIONAL INFORMATION.

Addendum One

RFB-21-24 KCTCS - Upgrade Life Safety - Somerset CC Addendum 01

KCTCS - Upgrade Life Safety - Somerset CC - Addendum 01 Drawings

Sheets

FA000 - FIRE ALARM GENERAL NOTES - SITE PLAN - SYMBOLS

S1-FA110 - BUILDING 1 FIRE ALARM DEMOLITION - LEVEL 1

S1-FA210 - BUILDING 1 FIRE ALARM - LEVEL 1

S5-FA110 - BUILDING 5 FIRE ALARM DEMOLITION - LEVEL 1

S5-FA210 - BUILDING 5 FIRE ALARM - LEVEL 1

File details come from the government source that posted it. Updated Mar 11, 2026.