Addendum No. 1.pdf

f:\projects\mis033\pm\bidding\2020-02-28 addendum 1\backup information\2020-02-28 addendum 1.docx

February 28, 2020

ADDENDUM NO. 1

State of Michigan

Department of Corrections

Saint Louis Correctional Facility

8585 North Croswell Road

Saint Louis, Michigan 48880

Century A&E Project No. MIS033

RE: Structural Repairs / Replacements

TO: PROSPECTIVE BIDDERS:

This Addendum forms a part of the Contract Documents and modifies the original Bidding Documents dated February 21, 2020. This addendum is to be initialed and submitted as part of each Bidder’s bid package. Failure to do so may subject Bidder to disqualification. This Addendum No. 1 consists of ten typed pages and revised contract drawing nos. A1.1 and A1.4.

REVISED SPECIFICATIONS

1. DC Spec Bid Schedule is revised and re-issued.

2. DC Spec Table of Contents is revised and re-issued.

3. DC Spec List of Shop Drawings in Section 01300 is revised and re-issued.

4. Section 08 80 00 Glazing is removed.

NEW SPECIFICATIONS

1. 08 88 53 Security Glazing is added.

REVISED DRAWINGS

1. Contract drawing no. A1.1 is revised and re-issued.

2. Contract drawing no. A1.4 is revised and re-issued.

END OF ADDENDUM NO. 1

Respectfully submitted, CENTURY A&E

Marvin Riedel, RA

Senior Architect

Distribution: All Bidders, Susan Wheaton (DTMB), Andrea Stinson (MDOC)

Bidding and Contract Document (R 11/19) Project Name: St. Louis Correctional Facility File No. 472/19496.SDW

Addenda: Bidder acknowledges receipt of Addenda: No. ___ dated: ________, No. ___ dated: ________ No. ___ dated: ________ FIRM NAME TELEPHONE NUMBER and E-MAIL ADDRESS

BID SCHEDULE

Base Bid Schedule - The Bidder will complete the Work and accept as full payment, for the Work items listed, the following Unit Prices and / or Item Bid Prices, as applicable:

Base Bid Item No.

Bid Quantity

Description Item Bid Price

1 27 New Doors

2 27 New Door Frames

3 5 New Door Hardware Set 1

4 3 New Door Hardware Set 2

5 1 New Door Hardware Set 3

6 4 New Door Hardware Set 4

7 11 New Door Hardware Set 5

8 3 New Door Hardware Set 6

9 7 New Door Hardware Set 7

10 7 New Door Hardware Set 8

11 27 Reinstall Balance of Existing Door Hardware

12 10 New Window Glazing

ALLOWANCE AMOUNT $25,000

Base Bid (Sum of Item Bid Prices for all Base Bid Items):

__________________________________________________________________ Dollars $__________________________ (use words) (in figures)

Bidding and Contract Document (R 11/19) Project Name: St. Louis Correctional Facility File No. 472/19496.SDW

TABLE OF CONTENTS

CONTRACT FORMS

BID SUMMARY FORM

BID SCHEDULE

QUALIFIED DISABLED VETERAN (QDV) BUSINESS REPRESENTATION

CERTIFICATION OF A MICHIGAN BASED BUSINESS

BID BOND

POST-BID SUBMITTALS

PERFORMANCE BOND

PAYMENT BOND

TABLE OF CONTENTS

DIVISION 00 - BIDDING REQUIREMENTS AND CONTRACT CONDITIONS

SECTION TITLE

00010 PRE-BID INFORMATION

00100 INSTRUCTIONS TO BIDDERS

00200 INFORMATION TO BIDDERS

00700 GENERAL CONDITIONS

00750 SPECIAL WORKING CONDITIONS

00900 ADDENDA

DIVISION 01 - GENERAL REQUIREMENTS

01010 SUMMARY OF WORK

01020 ALLOWANCES

01025 MEASUREMENT AND PAYMENT

01030 ALTERNATES

01040 COORDINATION

01050 FIELD ENGINEERING

01060 REGULATORY REQUIREMENTS

01090 REFERENCES

01100 PROJECT PROCEDURES

01200 PROJECT MEETINGS

01300 SUBMITTALS

01400 QUALITY CONTROL

01500 CONSTRUCTION FACILITIES AND TEMPORARY CONTROLS

01600 MATERIAL AND EQUIPMENT

01650 FACILITY START-UP

01700 CONTRACT CLOSE-OUT

01800 MAINTENANCE

DIVISION 02 - EXISTING CONDITIONS

02 41 19 SELECTIVE DEMOLITION

DIVISION 07 - THERMAL AND MOISTURE PROTECTION

07 92 00 JOINT SEALANTS

DIVISION 08 - OPENINGS

08 11 13 HOLLOW METAL DOORS AND FRAMES

08 71 00 DOOR HARDWARE

08 71 01 DOOR HARDWARE SETS

08 88 53 SECURITY GLAZING

DIVISION 09 - FINISHES

09 91 13 EXTERIOR PAINTING

09 91 23 INTERIOR PAINTING

Bidding and Contract Document (R 11/19) Project Name: St. Louis Correctional Facility File No. 472/19496.SDW

1. The Rev. 0 narrative will detail the Contractor's management of the site (lay down, parking, etc.). Further, the Rev. 0 narrative will identify shifts, weekend Work, Activity calendars, Delays since award and all pending and anticipated “or equal” and substitution proposals.

B. Once endorsed by the Owner and returned as "Resubmittal Not Required,” the Rev. 0 Progress Schedule (or Rev. 0A, etc.) will be the As-Planned Schedule and the basis for Update Submittals until the Rev. 1 Official Schedule is established. Once the As-Planned Schedule is established, the Owner will select Milestones and note Milestone Early and Late Dates. As the Official Schedule evolves, Milestone Dates will be revised accordingly.

C. If the Owner refuses to endorse the Rev. 0 Submittal (or Rev. 0A, for a resubmission) as "Resubmittal Not Required," the As- Planned Schedule will not be established. In that event, the Contractor will continue to submit Update and Revision Submittals reflecting progress and the Contractor's approach to remaining Work. The Owner will rely on the available Update and Revision Submittals, subject to whatever adjustments it determines appropriate.

2.15 UPDATE SUBMITTALS

A. Update Submittals with progress up to the closing date and updated Early and Late Dates for progress and remaining Activities will be due with each Request for Payment. As-built data will consist of actual start dates, percent complete, actual finish dates, changes, delays, and other significant events occurring before the closing date.

2.16 REVISION SUBMITTALS

A. Progress Schedule Revisions will be submitted with the third Request for Payment and every two (2) months after that, or more often, if necessary due to schedule recovery or other Progress Schedule revisions. Revisions will revise the Update Submittal attached to the prior Request for Payment.

B. Progress Schedule revisions will detail all impacts on pre-existing Activity scope, logic ties and restraint dates and reflect the Contractor's current approach to Work remaining. Revisions may be required because of changes in the Work, substitutions, schedule recovery and Delays.

C. Once endorsed by the Owner and returned as "Resubmittal Not Required," a Revision Submittal becomes the Rev. 1, Rev. 2, etc. Official Schedule and the basis for subsequent Update Submittals until a more current Official Schedule is established. If the Owner refuses to endorse a Revision Submittal as "Resubmittal Not Required," the Contractor will continue to submit Update and Revision Submittals when and as required in this Section.

2.17 RETROSPECTIVE DELAY ANALYSIS

A. If the Owner refuses to endorse any Revision Submittal as “Resubmittal Not Required,” the Contractor and Owner will use the latest Official Schedule when evaluating the effect of Delays on Contract Time and / or Contract Price. The procedure will consist of progressively revising the latest Official Schedule at key Revision Submittal closing dates. For each Progress Schedule iteration, slippage between actual Milestone Dates and Rev. 0 Milestone Dates will be correlated to Delays occurring solely in that iteration. Revisions affecting Work after any iteration will be included only to the extent consented by the Owner at that time and / or if actually confirmed by as-built progress.

3. Shop Drawings: The Contractor shall deliver shop drawings of products, materials, assemblies, or equipment to the

Professional.

Item of Work Section Number

Selective Demolition 02 41 19 Joint Sealants 07 92 00 Hollow Metal Doors and Frames 08 11 13 Door Hardware 08 71 00 Door Hardware Sets 08 71 01 Security Glazing 08 88 53 Exterior Painting 09 91 13 Interior Painting 09 91 23

END OF SECTION 01300

SECTION 01400 QUALITY CONTROL

1. Testing Laboratory Services: Not applicable.

END OF SECTION 01400

Project Name: St. Louis Correctional Facility

Project Number: MIS033

SECTION 08 88 53

SECURITY GLAZING

Page 1 CENTURY A&E

SECTION 08 88 53 - SECURITY GLAZING

PART 1 - GENERAL

1.1 SUMMARY

A. Section includes monolithic polycarbonate and laminated polycarbonate.

1.2 COORDINATION

A. Coordinate glazing channel dimensions to provide necessary bite on security glazing, minimum edge and face clearances, and adequate sealant thicknesses, with reasonable tolerances.

1.3 ACTION SUBMITTALS

A. Product Data: For each type of product.

B. Security Glazing Schedule: List security glazing types and thicknesses for each size opening and location. Indicate coordinated dimensions of security glazing and construction that receives security glazing, including clearances and glazing channel dimensions.

1.4 WARRANTY

A. Manufacturer's Special Warranty for Polycarbonate Sheet: Manufacturer agrees to replace polycarbonate sheet that deteriorates within specified warranty period.

Deterioration of polycarbonate sheet is defined as defects developed from normal use that are not attributed to maintaining and cleaning polycarbonate sheet contrary to manufacturer's written instructions. Defects include yellowing and loss of light transmission.

1. Warranty Period: 10 years from date of Substantial Completion.

B. Manufacturer's Special Warranty for Laminated Polycarbonate: Manufacturer agrees to replace laminated polycarbonate that deteriorates within specified warranty period.

Deterioration of laminated polycarbonate is defined as defects developed from normal use that are not attributed to maintaining and cleaning laminated polycarbonate contrary to manufacturer's written instructions. Defects include edge separation, delamination materially obstructing vision through glazing, blemishes exceeding those allowed by referenced standard, yellowing, and loss of light transmission.

1. Warranty Period: 10 years from date of Substantial Completion.

PART 2 - PRODUCTS

2.1 PERFORMANCE REQUIREMENTS

A. Thermal Movements: Allow for thermal movements from ambient and surface temperature changes acting on glazing framing members and glazing components.

Page 2 CENTURY A&E

1. Temperature Change: 120 deg F, ambient; 180 deg F, material surfaces.

B. Safety Glazing: Where safety glazing is indicated, provide glazing that complies with

16 CFR 1201, Category II.

2.2 SECURITY GLAZING, GENERAL

A. Glazing Publications: Comply with published recommendations of security glazing and glazing material manufacturers and organizations below unless more stringent requirements are indicated. Refer to these publications for glazing terms not otherwise defined in this Section or in referenced standards.

1. GANA Publications: "Laminated Glazing Reference Manual" and "Glazing

Manual."

B. Plastic Glazing Labeling: Identify plastic sheets with appropriate markings of applicable testing and inspecting agency, indicating compliance with required fire-test-response characteristics.

C. Fire-Test-Response Characteristics of Polycarbonate Sheets: As determined by testing polycarbonate sheets identical to those used in security glazing products by a qualified testing agency acceptable to authorities having jurisdiction.

1. Self-ignition temperature of 650 deg F or more when tested according to

ASTM D 1929 on plastic sheets in thicknesses indicated for the Work.

2. Smoke-Developed Index of 450 or less when tested according to ASTM E 84, or smoke density of 75 or less when tested according to ASTM D 2843 on plastic sheets in thicknesses indicated for the Work.

3. Burning extent of 1 inch or less when tested according to ASTM D 635 at a nominal thickness of 0.060 inch or thickness indicated for the Work.

D. Thermal and Optical Performance Properties: Provide security glazing with performance properties specified, as indicated in manufacturer's published test data, based on construction products indicated and on procedures indicated below:

1. U-Factors: Center-of-glazing values, according to NFRC 100 and based on LBL's

WINDOW 5.2 computer program, expressed as Btu/sq. ft. x h x deg F.

2. Solar-Heat-Gain Coefficient and Visible Transmittance: Center-of-glazing values, according to NFRC 200 and based on LBL's WINDOW 5.2 computer program.

3. Visible Reflectance: Center-of-glazing values, according to NFRC 300.

2.3 POLYCARBONATE SECURITY GLAZING

A. Polycarbonate Sheet: ASTM C 1349, Appendix X1, Type II, coated, mar-resistant, UV-stabilized polycarbonate with coating on exposed surfaces and Type I, standard, UV-stabilized polycarbonate where no surfaces are exposed.

Page 3 CENTURY A&E

B. Laminated Polycarbonate: Polycarbonate sheets laminated with clear urethane interlayer that complies with ASTM C 1349, Appendix X2, and has a proven record of no tendency to bubble, discolor, or lose physical and mechanical properties after fabrication and installation. Provide laminated units that comply with requirements of ASTM C 1349 for maximum allowable laminating process blemishes and haze.

2.4 SPALL-RESISTANT FILM

A. Spall-Resistant Film: Composite of clear polyvinyl butyral film and clear abrasion-resistant polyester film.

B. Laminating Process: Factory laminate spall-resistant film to glazing assemblies to produce laminated lites free of foreign substances and air.

2.5 GLAZING SEALANTS

A. General:

1. Compatibility: Provide glazing sealants that are compatible with one another and with other materials they contact, including security glazing, and glazing channel substrates, under conditions of service and application, as demonstrated by sealant manufacturer based on testing and field experience.

2. Suitability: Comply with sealant and security glazing manufacturers' written instructions for selecting glazing sealants suitable for applications indicated and for conditions existing at time of installation.

3. Colors of Exposed Glazing Sealants: As selected by Owner from manufacturer's full range.

B. Security Sealant: Manufacturer's standard, nonsag, tamper-resistant sealant for joints with low movement complying with ASTM C 920, Grade NS, Class 12.5 or 25, Use NT, and with a Shore A hardness of at least 45 when tested according to ASTM C 661.

2.6 GLAZING TAPES

A. Back-Bedding Mastic Glazing Tapes: Preformed, butyl-based, 100 percent solids elastomeric tape; nonstaining and nonmigrating in contact with nonporous surfaces; with or without spacer rod as recommended in writing by tape and security glazing manufacturers for application indicated; and complying with ASTM C 1281 and

AAMA 800 for products indicated below:

1. AAMA 807.3 tape, for glazing applications in which tape is not subject to continuous pressure.

B. Expanded Cellular Glazing Tapes: Closed-cell, PVC foam tapes; factory coated with adhesive on both surfaces; and complying with AAMA 800 for the following types:

1. AAMA 810.1, Type 1, for glazing applications in which tape acts as the primary sealant.

2. AAMA 810.1, Type 2, for glazing applications in which tape is used in combination with a full bead of liquid sealant.

Page 4 CENTURY A&E

2.7 MISCELLANEOUS GLAZING MATERIALS

A. Cleaners, Primers, and Sealers: Types recommended by sealant or gasket manufacturer.

B. Setting Blocks: Elastomeric material with a Shore, Type A durometer hardness of 85, plus or minus 5.

C. Spacers: Elastomeric blocks or continuous extrusions of hardness required by security glazing manufacturer to maintain security glazing lites in place for installation indicated.

D. Edge Blocks: Elastomeric material of hardness needed to limit security glazing lateral movement (side walking).

E. Cylindrical Glazing Sealant Backing: ASTM C 1330, Type O (open-cell material), of size and density to control glazing sealant depth and otherwise produce optimum glazing sealant performance.

2.8 FABRICATION OF SECURITY GLAZING

A. Fabricate security glazing in sizes required to fit openings indicated for Project, with edge and face clearances, edge and surface conditions, and bite complying with written instructions of product manufacturer and referenced glazing publications, to comply with system performance requirements.

PART 3 - EXECUTION

3.1 GLAZING, GENERAL

A. Comply with combined written instructions of manufacturers of security glazing, sealants, gaskets, and other glazing materials unless more stringent requirements are indicated, including those in referenced glazing publications.

B. Protect edges of security glazing from damage during handling and installation. Remove damaged security glazing from Project site and legally dispose of off Project site.

Damaged security glazing includes units with edge or face damage or other imperfections that, when installed could weaken security glazing and impair performance and appearance.

C. Apply primers to joint surfaces where required for adhesion of sealants, as determined by preconstruction testing.

D. Install setting blocks in sill rabbets, sized and located to comply with referenced glazing publications unless otherwise required by glazing unit manufacturer. Set blocks in thin course of compatible sealant suitable for heel bead.

E. Do not exceed edge pressures stipulated by security glazing manufacturers for installing lites.

Page 5 CENTURY A&E

F. Provide spacers for security glazing lites where the length plus width is larger than 50 inches.

G. Provide edge blocking where indicated or needed to prevent security glazing from moving sideways in glazing channel, as recommended in writing by security glazing manufacturer and according to requirements in referenced glazing publications.

3.2 TAPE GLAZING

A. Position tapes on fixed stops so that, when compressed by security glazing, their exposed edges are flush with or protrude slightly above sightline of stops.

B. Install tapes continuously, but not necessarily in one continuous length. Do not stretch tapes to make them fit opening.

C. Cover vertical framing joints by applying tapes to heads and sills first and then to jambs.

Cover horizontal framing joints by applying tapes to jambs and then to heads and sills.

D. Place joints in tapes at corners of opening with adjoining lengths butted together, not lapped. Seal joints in tapes with compatible sealant approved by tape manufacturer.

E. Do not remove release paper from tape until just before each glazing unit is installed.

F. Apply heel bead of elastomeric sealant.

G. Center security glazing in openings on setting blocks and press firmly against tape by inserting dense compression gaskets formed and installed to lock in place against faces of removable stops. Start gasket applications at corners and work toward centers of openings.

H. Apply cap bead of elastomeric sealant over exposed edge of tape.

3.3 GASKET GLAZING (DRY)

A. Cut compression gaskets to lengths recommended by gasket manufacturer to fit openings exactly, with allowance for stretch during installation.

B. Insert soft compression gasket securely in place between glazing unit and frame or fixed stop, so it is securely in place with joints miter cut and bonded together at corners.

C. Installation with Drive-in Wedge Gaskets: Center security glazing in openings on setting blocks and press firmly against soft compression gasket by inserting dense compression gaskets formed and installed to lock in place against faces of removable stops. Start gasket applications at corners and work toward centers of openings. Compress gaskets to produce a weathertight seal without developing bending stresses in security glazing. Seal gasket joints with sealant recommended by gasket manufacturer.

Page 6 CENTURY A&E

D. Installation with Pressure-Glazing Stops: Center security glazing in openings on setting blocks and press firmly against soft compression gasket. Install dense compression gaskets and pressure-glazing stops, applying pressure uniformly to compression gaskets.

Compress gaskets to produce a weathertight seal without developing bending stresses in security glazing. Seal gasket joints with sealant recommended by gasket manufacturer.

E. Install gaskets so they protrude past face of glazing stops.

3.4 SEALANT GLAZING (WET)

A. Install continuous spacers, or spacers combined with cylindrical sealant backing, between security glazing and glazing stops to maintain face clearances and to prevent sealant from extruding into glazing channel and blocking weep systems. Secure spacers or spacers and backings in place and in position to control depth of installed sealant relative to edge clearance for optimum sealant performance.

B. Force sealants into glazing channels to eliminate voids and to ensure complete wetting or bond of sealant to security glazing and channel surfaces.

C. Tool exposed surfaces of sealants to provide a substantial wash-away from security glazing.

3.5 CLEANING AND PROTECTION

A. Immediately after installation remove nonpermanent labels and clean surfaces.

B. Protect security glazing from contact with contaminating substances resulting from construction operations.

1. If, despite such protection, contaminating substances do come into contact with security glazing, remove substances immediately as recommended in writing by security glazing manufacturer. Remove and replace security glazing that cannot be cleaned without damage.

3.6 MONOLITHIC POLYCARBONATE SECURITY GLAZING SCHEDULE

A. Security Glazing: Monolithic polycarbonate with mar-resistant coating on both surfaces.

1. Products: Subject to compliance with requirements, provide the following:

2. Thickness: 3/8 inch.

3.7 LAMINATED-POLYCARBONATE SECURITY GLAZING SCHEDULE

A. Security Glazing: Laminated polycarbonate.

1. Products: Subject to compliance with requirements, provide the following:

2. Maximum Overall Unit Thickness: 1 inch.

END OF SECTION

AJA

MER/AJA

A1.1 1/8" = 1'-0"

FO

O

D S

E R

V

IC

E B

U

IL

D

IN

G F

LO

O

R P

LA

N

SHEET NO.

PROJECT NO: MIS033

DWG. SCALE:

DESIGN BY:

DRAWN BY:

NO

DA

TE

RE

VI

SI

ON

S

BY

Cr ah en A ve nu e N

E

- G ra nd

R ap id s, M I 4

Te le ph on e:

(6

) 4

-5

F ax

6)

-5

W eb

: w w w .c en tu ry ae

.c om

E N T U R Y

Fa ci lit ie s D es ig n

C A E

S T

A T

E O

F M

IC

H

IG

A

N D

E P

A R

T M

E N

T O

F C

O R

R E

C T

IO

N

S

FI

LE

N O

2/

6.

S D

W

F U

N D

IN

G

C O

D E

S

LF

M A

IN

T

P R

O J

P L U R I B U E

S U N U M

C I R C U M S P I C E

S I QU EREI S PENI NSUL AM AMOENAM

DEPARTMENT OF TECHNOLOGY, MANAGEMENT AND BUDGET

STATE OF MICHIGAN

ROBERT C. HALL, RA, NCARB, DIRECTOR

FACILITIES AND BUSINESS SERVICES ADMINISTRATION

DESIGN AND CONSTRUCTION DIVISION

S T

R U

C T

U R

A L

R E

P A

IR

S

R

E P

L A

C E

M E

N T

S

IS

SU

ED

F

OR

A

DD

EN

DU

M

ME

R

2 -

S T

L

O U

IS

C

O R

R E

C T

IO

N

A L

F A

C

IL

IT

Y

S

T

L O

U

IS

M

IC

H

IG

A

N

SITE KEY PLAN

FS1

FS2FS3

FS4 FS5

FS6

FS7

FS8

FS

TYPE "A" TYPE "B" TYPE "C" TYPE "D"

FRAME F1 FRAME F2 FRAME F3 FRAME F4

FRAME F5 FRAME F6 FRAME F7

DOOR TYPE

FRAME TYPE

AJA

MER/AJA

A1.4

AS NOTED

S C

H E

D U

LE

S

SHEET NO.

PROJECT NO: MIS033

DWG. SCALE:

DESIGN BY:

DRAWN BY:

NO

DA

TE

RE

VI

SI

ON

S

BY

Cr ah en A ve nu e N

E

- G ra nd

R ap id s, M I 4

Te le ph on e:

(6

) 4

-5

F ax

6)

-5

W eb

: w w w .c en tu ry ae

.c om

E N T U R Y

Fa ci lit ie s D es ig n

C A E

S T

A T

E O

F M

IC

H

IG

A

N D

E P

A R

T M

E N

T O

F C

O R

R E

C T

IO

N

S

FI

LE

N O

2/

6.

S D

W

F U

N D

IN

G

C O

D E

S

LF

M A

IN

T

P R

O J

P L U R I B U E

S U N UM

C I R C U M S P I C E

S I QU EREI S PENI NSULAM AMOENAM

DEPARTMENT OF TECHNOLOGY, MANAGEMENT AND BUDGET

STATE OF MICHIGAN

ROBERT C. HALL, RA, NCARB, DIRECTOR

FACILITIES AND BUSINESS SERVICES ADMINISTRATION

DESIGN AND CONSTRUCTION DIVISION

S T

R U

C T

U R

A L

R E

P A

IR

S

R

E P

L A

C E

M E

N T

S

IS

SU

ED

F

OR

A

DD

EN

DU

M

ME

R

2 -

S T

L

O U

IS

C

O R

R E

C T

IO

N

A L

F A

C

IL

IT

Y

S

T

L O

U

IS

M

IC

H

IG

A

N

B. Safety Glazing: Where safety glazing is indicated, provide glazing that complies with 16 CFR 1201, Category II.

B. Security Sealant: Manufacturer's standard, nonsag, tamper-resistant sealant for joints with low movement complying with ASTM C 920, Grade NS, Class 12.5 or 25, Use NT, and with a Shore A hardness of at least 45 when tested according to ASTM C 661.

B. Safety Glazing: Where safety glazing is indicated, provide glazing that complies with 16 CFR 1201, Category II.

B. Security Sealant: Manufacturer's standard, nonsag, tamper-resistant sealant for joints with low movement complying with ASTM C 920, Grade NS, Class 12.5 or 25, Use NT, and with a Shore A hardness of at least 45 when tested according to ASTM C 661.