Addendum 2.pdf

COMMONWEALTH OF KENTUCKY

DEPARTMENT FOR FACILITIES AND SUPPORT SERVICES

DIVISION OF ENGINEERING AND CONTRACT ADMINISTRATION

INVITATION TO BID NO: RFB-267-25

FOR: HVAC Upgrades

Kentucky State Police- Post 3 Bowling Green, Kentucky

DATE: July 1, 2025

RFB-785-2500000731

ADDENDUM NO. Two (2)

BIDDER SHALL CONFORM TO THE FOLLOWING CHANGES AS SAME SHALL BECOME BINDING

UPON THE CONTRACT TO BE ISSUED IN RESPONSE TO THIS INVITATION TO BID.

Item 1: Refer to addendum to be distributed by Lynn Imaging for all additions, deletions, and/or changes to specifications and/or drawings.

END OF ADDENDUM

Invitation to Bid No. RFB-267-25 For: HVAC Upgrades

Kentucky State Police- Post 3 Bowling Green, Kentucky

Janis Wilhoite, Statewide Procurement Analyst II Division of Engineering and Contract Administration

POST 3 – HVAC UPGRADES

KENTUCKY STATE POLICE

BOWLING GREEN, KENTUCKY

MARCUM NO. 24619

ACCOUNT NO. 520-CBZ6-BG02-00

ADDENDUM 2.00

JULY 1, 2025

The following Addendum Items shall be made part of the Contract Documents for the referenced project.

2.01 Refer to Section 10000.4 – Daily Work Times. Work schedules for work to be completed in the attic can be adjusted due to the heat potential in the attic.

Contractor shall schedule with the Owner at minimum 48 hours prior to work commencing.

2.02 Refer to Section 10000.4 – Daily Work Times. Duct cleaning work shall be completed during afternoons after 5:00pm or at night when building occupancy is lower. This work shall not occur between 6:00am and 5:00pm.

2.03 Refer to Drawing DME1.1. Omit this drawing in its entirety and replace with the attached Drawing DME1.1 Revision 1 dated 06/27/25.

2.04 Refer to Drawing ME1.1. Omit this drawing in its entirety and replace with the attached Drawing ME1.1 Revision 1 dated 06/27/25.

2.05 Refer to Drawing ME4.1. Omit this drawing in its entirety and replace with the attached Drawing ME4.1 Revision 1 dated 06/27/25.

2.06 Refer to Drawing ME5.1. Omit this drawing in its entirety and replace with the attached Drawing ME5.1 Revision 1 dated 06/27/25.

2.07 Refer to Drawing ME1.1, Mechanical Construction Tag Note 9. Contractor shall saw cut existing metal deck and concrete roof structure between existing bar joists for installation of attic access hatch with pull down ladder. Attic access shall be equal to Fakro Model DRL Flat Roof Hatch, deck mount, R-value 8.3, with Model LML aluminum folding access ladder to be adjusted for the deck height; five year warranty. At the opening in the existing roof, the Contractor shall furnish and install framing per the attached detail on Sketch XH01.

2.08 Refer to Drawing ME1.1. There are existing lighting fixtures in the attic. The

Contractor shall have the option to make existing lighting fixtures operational in lieu of providing temporary lighting for construction lighting.

2.09 Refer to Drawings DME1.1 and ME1.1. The Owner will relocate all stored materials from mechanical room.

Attachments:

1. Drawing DME1.1, Revision 1

2. Drawing ME1.1, Revision 1

3. Drawing ME4.1, Revision 1

4. Drawing ME5.1, Revision 1

5. Sketch XH01

END OF ADDENDUM 2.00

A.A.

16x14 SA x1

SA

12Ø SA

x1

SA

20x14 SA14x10 SA x1

SA

18x14 SA14x10 SA10x10 SA8x10 SA8x8 SA

4-2

VVT 3-2

VVT

5-3

VVT

4-3

VVT 3-3

VVT

2-3

VVT

1-3

VVT

2-4

VVT

3-4

VVT

1-4

VVT

1-4

VVT

BP-4

VVT

1-2

VVT

2-2

VVT

BP-3 VVT

12x10 SA

3-1

VVT

T T T

T

T

T

T

T T

T

T

T

TT

T

2-1

VVT

1-1

VVT

EF

EF

EF

RH

IU

IU

IU

EF

EF

EF

EF

R

EF R

EF

REF

REF

DISPATCH

VEST.

ADMIN. OFFICE

OFFICE

103OFFICE

OFFICE

OFFICE

OFFICE

OFFICE

EVIDENCE

OFFICE

OFFICE

RADIO

TECH

EVIDENCE

CONFERENCE

WOMENS

MENS

VEST.

OFFICE

118 FILE STOR.

MECH. /

STOR.

WOMENS

123 LOUNGE

IDF

CORRIDOR

JAN.

RESTROOM

OFFICE

OFFICE

OFFICE

MENS

VEST.

OU

OU

OU

OU

IU

IU

(TYP.)

(TYP.)

STOR.

T

PANTRY

OFFICE

T

CF CF

14x12 SA

12 12

17 7

CF

10x10 SA

(TYP.)

(TYP.)

VVT

CU CU CU CU

(TYP.)

EUH

2 2

5 5 x1

SA

(TYP.)

(TYP.)

N G

GFIGFI

WP

L

WH

(TYP)

F F F

F

SS

NORTH

PROJECT

SCALE: 1/8" = 1'-0"

DEMOLITION FLOOR PLAN

A

B

C

17 18 19 20

F

D

E

G

H

J

K

L

N

M

O

P

R

1 2 43 5 6 87 9 10 11 12 13 14 15 16

DECA LOG #

DRAWING NO.

AS BUILT DATE

FRANKFORT, KENTUCKY

DIVISION OF ENGINEERING AND CONTRACT ADMINISTRATION

DEPARTMENT FOR FACILITIES AND SUPPORT SERVICES

FINANCE AND ADMINISTRATION CABINET

COMMONWEALTH OF KENTUCKYACCOUNT NO.

DATEDESCRIPTION OF REVISIONS

REVISION HISTORY OF THIS DRAWING

DATEDESCRIPTION OF REVISIONS

A&E FILE NO. 24619

DRAWING DATE 05/07/2025

DRAWN BY

CHECKED BY

PHASE RTA

RTA DATE

DRAWING INFORMATION

KSP POST NO. 3 - HVAC UPGRADES

3119 NASHVILLE ROAD, BOWLING GREEN KY

520-CBZ6-BG02-00

05/23/2025

Paducah, KY Office

2301 McCracken Blvd Paducah, KY 42001

270-444-9274 MarcumEngineering.net

BA/MM

BY/AD DME1.1

MECH-ELEC DEMOLITION PLAN

MECHANICAL

DEMOLITION TAG NOTES

(APPLIES TO THIS DRAWING ONLY)

1 CONTRACTOR SHALL REMOVE EXISTING BYPASS DAMPER AND ASSOCIATED

DUCTWORK BACK TO MAIN AND CAP.

2 CONTRACTOR SHALL MANUALLY OPEN EXISTING VVT DAMPER AND FIX IN THE

FULL OPEN POSITION.

3 REMOVE EXISTING EXHAUST FAN. PROTECT DUCTWORK FOR REUSE.

4 CAP EXISTING DUCT OFF FOR ZONE 1 DUCT MODIFICATIONS.

CONTRACTOR SHALL REMOVE EXISTING FURNACES, REFRIGERANT PIPING,

DISCONNECT GAS PIPING, CONDENSING UNITS, ETC. PROTECT SUPPLY

DUCTWORK FOR REUSE WHERE INDICATED.

REMOVE ALL EXISTING THERMOSTATS, CONTROLS, WIRING, ETC. IN ITS ENTIRETY.

INSTALL BLANK COVER PLATE ON WALL BOXES. COLOR SHALL BE MATCH

EXISTING ELECTRICAL DEVICE COVER PLATES.

7 EXISTING DUCTLESS MINI SPLIT SYSTEM TO REMAIN.

8 REMOVE EXISTING DIFFUSER AND FLEXIBLE DUCTWORK BACK TO SHEETMETAL

DUCT. PROTECT SHEET METAL DUCT FOR REUSE, UNLESS OTHERWISE NOTED.

9 REMOVE EXISTING RETURN AIR GRILLE AND ANY ASSOCIATED SOUND TRAP IN ITS

ENTIRETY. INSTALL NEW CEILING TILE IN ITS LOCATION TO MATCH EXISTING.

10 REMOVE EXISTING DIFFUSER, FLEXIBLE DUCT, AND DUCT TAKEOFF TO MAIN AND

CAP.

11 REMOVE SECTION OF DUCTWORK AS INDICATED IN ITS ENTIRETY. PROTECT

REMAINING DUCTWORK FOR RESUSE. REFER TO NEW WORK PLAN.

12 REMOVE EXISTING DIFFUSER, FLEXIBLE DUCT, ETC. IN ITS ENTIRETY. INSTALL

NEW CEILING TILE IN ITS LOCATION TO MATCH EXISTING.

REMOVE EXISTING CONCENTRIC VENT FLUES THROUGH WALL AND ALL

ASSOCIATED COMBUSTION AIR INTAKE AND FLUE BACK TO EACH FURNACE

INCLUDING ALL HANGERS AND SUPPORTS.

14 PROTECT EXISTING OUTSIDE AIR LOUVER AND DUCTWORK FOR REUSE.

DISCONNECT FROM EXISTING RETURN AIR CONNECTIONS.

REMOVE EXISTING FURNACE, REFRIGERANT PIPING, DISCONNECT GAS PIPING,

CONDENSING UNITS, ETC. IN ITS ENTIRETY. REMOVE SUPPLY AIR DUCT TO

EXTENTS SHOWN. PROTECT REMAINING SUPPLY AIR DUCT FOR REUSE.

16 REMOVE EXISTING RETURN AIR DUCT IN ITS ENTIRETY. PATCH OPENINGS IN

MECHANICAL ROOM WALLS TO MATCH EXISTING.

17 EXISTING ATTIC ACCESS OPENING ABOVE LAY-IN CEILING.

18 REMOVE EXISTING DUCTLESS SPLIT UNIT, REFRIGERANT PIPING, ETC. IN ITS

ENTIRETY.

19 REMOVE EXISTING EXHAUST FAN AND ASSOCIATED DUCTWORK IN ITS ENTIRETY.

PROTECT EXISTING LOUVER FOR REUSE.

20 CONTRACTOR SHALL REMOVE EXISTING WATER HEATER AND ASSOCIATED PIPES

UP TO CEILING SPACE PROTECT PIPING FOR REUSE.

DEMO NATURAL GAS PIPING BRANCHES FROM FURNACES BACK TO MAIN.

PROTECT EXISTING NATURAL GAS MAIN PIPING FOR REUSE. MODIFY GAS PIPING

AS NECESSARY TO PERFORM NEW WORK.

22 DEMO EXISTING UNIT HEATER AND ASSOCIATED COMPONENTS IN ITS ENTIRETY.

ELECTRICAL

DEMOLITION TAG NOTES

(APPLIES TO THIS DRAWING ONLY)

CONTRACTOR SHALL REMOVE AND DISCONNECT ALL WIRE AND CONDUIT FROM

THE FURNACE BACK TO THE NEAREST JUNCTION BOX. REMOVE 1P20A BREAKER

FROM PANEL B1 CIRCUIT 1,2,3,AND 4.

CONTRACTOR SHALL REMOVE AND DISCONNECT ALL WIRE AND EXPOSED

CONDUIT FROM THE ELECTRICAL DISCONNECT BACK TO THE PANEL. REMOVE

3POLE BREAKER FROM PANEL B1 CIRCUIT (5,7,9), (11,13,15),(16,18,20) AND

(26,28,30). DISCONNECT AND REMOVE CONDUIT ATTACHED TO THE OUTSIDE

BRICK WALL.

CONTRACTOR SHALL DISCONNECT AND REMOVE WIRE AND CONDUIT FROM

EXHAUST FAN BACK TO THE NEAREST JUNCTION BOX. CONTRACTOR SHALL

DISCONNECT AND REMOVE WIRE FROM LIGHT SWITCH TO EXHAUST FAN.

4 CONTRACTOR SHALL REMOVE AND DISCONNECT THE HVAC CONTROLS IN THEIR

ENTIRETY BACK TO SOURCE.

5 NO ELECTRICAL WORK TO BE COMPLETED IN AREA.

6 CONTRACTOR SHALL DISCONNECT WIRE FROM UNIT. REMOVE WIRE AND CONDUIT

BACK TO SOURCE IN ITS ENTIRETY ALONG WITH LOCAL DISCONNECT.

CONTRACTOR SHALL DISCONNECT AND REMOVE WIRE AND CONDUIT FROM

EXHAUST FAN BACK TO THE NEAREST JUNCTION BOX. CONNECTION TO LIGHT

SWITCH AND CIRCUIT SHALL REMAIN.

8 REMOVE WIRE AND CONDUIT FROM EXHAUST FAN BACK TO SOURCE. REMOVE

SWITCH CONTROL WITH INTERLOCKS IN THEIR ENTIRETY.

9 DISCONNECT POWER FROM EXISTING WATER HEATER. PROTECT CONNECTIONS

FOR RE-USE.

10 DISCONNECT AND REMOVE WIRE FROM AC UNIT TO DISCONNECT.

CONTRACTOR SHALL DISCONNECT WIRE FROM UNIT. REMOVE WIRE AND CONDUIT

BACK TO SOURCE IN ITS ENTIRETY ALONG WITH LOCAL DISCONNECT. REMOVE

2P25 BREAKER AND REPLACE WITH BLANK COVER.

12 EXISTING RECEPTACLE SHALL STAY IN PLACE AND ACTIVE. PROTECT DURING

DEMOLITION.

REMOVE EXISTING UNIT HEATER IN ITS ENTIRETY INCLUDING WIRE AND EXPOSED

CONDUIT BACK TO THE PANEL. PLACE BLANK FACEPLATE OVER EXPOSED

OPENING.

CONTRACTOR SHALL DISCONNECT WIRE FROM UNIT. REMOVE WIRE AND CONDUIT

BACK TO NEAREST JUNCTION BOX IN ITS ENTIRETY ALONG WITH LOCAL

DISCONNECT.

Addendum 2.0

4" COMPACTED CA-6

SEE SITE PLAN FOR WIDTH

FINISHED GRADE

4" THICK CONCRETE SLAB 4500

PSI MIN. COMPRESSIVE

STRENGTH REINFORCED W/ 6X6

- W1.4XW1.4 W.W.F. (BROOM

FINISH)

NOTE: TOOLED CONSTRUCTION JOINTS SHALL BE

MADE ON MAXIMUM JOINT SPACING TO SIDEWALK

WIDTH RATIO OF 1:1 (TYP.) EXPANSION JOINTS @

MAXIMUM 100' INTERVALS.

THICKENED SIDEWALK EDGE

WHERE NOTED ON THE DRAWINGS

NOTE:

1. CONTROL JOINTS SHALL BE MADE ON MAXIMUM JOINT SPACING TO

SIDEWALK WIDTH RATION OF 1:1 (TYP.)

2. CONTROL JOINTS IN OTHER PEDESTRIAN CONCRETE AREAS SHALL BE

PER PLAN AND NOT TO EXCEED 10'.

CONTROL JOINT (DEPTH = 1/4 SLAB

THICKNESS).

2 SCALE: N.T.S.

CONCRETE CONTROL JOINT1 SCALE: N.T.S.

FLUSH CONCRETE SIDEWALK

1.

0'

X X X X X X X X X X

CIVIL

DEMOLITION TAG NOTES

(APPLIES TO THIS DRAWING ONLY)

1 EXISTING CONCRETE PATIO AND SIDEWALK TO REMAIN AND BE PROTECTED.

2 REMOVE EXISTING SHRUBS INCLUDING ALL ROOT BALLS, ROOTS, ETC. IN THEIR

ENTIRETY.

REMOVE EXISTING GRAVEL, WEED BARRIER, AND SOILS TO 12" BELOW EXISTING

GRADE. REMOVE 4" CORRUGATED DRAINAGE PIPE FROM CENTER OF AREA AND

CAP BELOW GRADE.

6/27/25

A.A.

16x14 SA x1

S

A

14x10 SA

18x14 SA10x10 SA

12x10 SA

DISPATCH

VEST.

ADMIN. OFFICE

101OFFICE

103OFFICE

OFFICE

OFFICE

OFFICE

OFFICE

EVIDENCE

OFFICE

OFFICE

RADIO

TECH

EVIDENCE

CONFERENCE

WOMENS

MENS

VEST.

OFFICE

FILE STOR.

MECH. /

STOR.

WOMENS

123 LOUNGE

IDF

CORRIDOR

JAN.

RESTROOM

OFFICE

OFFICE

OFFICE

MENS

VEST.

STOR.

PANTRY

OFFICE

14x12 SA

10x10 SA

RH

IU

IU

OU

OU

IU

CF CF CF

S-2

S-2

S-2

S-3

S-3

S-3 310 S-2

S-1

S-1

S-1

S-1

S-1

S-2

S-2

S-1

S-2 165 S-2

S-2

S-2

S-2

S-1

S-1

S-3

S-3

16x14 SA

16x14 SA

Ø

S A

S-1 50 10 x1

S A

S-2

S-2

6x

S A

S-1 x1

S

A12x10 SA

16x14 SA x1

S

A

S-1

S-2 x1

S

A

10x10 SA

14x16 RA12x14 RA

14x16 RA

6x

R A

6x

R A x1

R

A

14x16 RA14x14 RA12 x1

R

A

8x10 RA

8x

R A

8x

R A

R-1

R-1

R-1

R-1

R-1

R-1

R-1

R-1

R-1

R-1 x1

R

A

10x8 RA

R-1

6x

R A

R-1

12x12 RA 10x10 RA

6x6 RA

6x6 RA

8x8 RA

R-1

R-1

R-1

S-1

S-1

10x12 RA

12x12 RA 6x6 RA

10x12 RA10x12 RA

R-1

R-1

R-1

6 7

8 7

AHU

HP

L

R-1

R-1

EF

EF

4 EF

EF

EF

EF

HP

HP

HP

HP

10x10 EA 12x12 OAL

X

10x10 SA

16x16 RA

S-4

S-4

OU

IU

D

SS

16x14 SA

R E

F

R E

F

B-2

PANTRY

MAIN

E

M M M

M

HP

HP

HP

HP

REF

REF

WH

F

F

F

F

MECH. /

STOR.

(TYP.)

(TYP.)

L

A.A.

DISPATCH

VEST.

ADMIN. OFFICE

101OFFICE

103OFFICE

OFFICE

OFFICE

OFFICE

OFFICE

EVIDENCE

OFFICE

OFFICE

RADIO

TECH

EVIDENCE

CONFERENCE

WOMENS

MENS

VEST.

OFFICE

FILE STOR.

MECH. /

STOR.

WOMENS

123 LOUNGE

IDF

CORRIDOR

JAN.

RESTROOM

OFFICE

OFFICE

OFFICE

MENS

VEST.

STOR.

PANTRY

OFFICE

(TYP)

2 2

EPEP EPEP EPEP EPEP3

4 5

6 6 6

6 6

SS 8

OSOS

OSOS

OSOS

OSOS

OSOS

EPEP

EPEP

EPEPEPEP

EPEPEPEP

EPEP

EPEP

EPEP

EPEP

B1-5,7 B1-11,13

B1-16,18 B1-26,28

EPEP EPEP EPEP

EPEP

B1-2

B1-4

B1-1

B1-3

AHU

HP

EF

EF

4 EF

EF

EF

EF

HP

HP

HP

HP

F

F

F

F

B-1 B-2

MAIN

E

PANTRY

MAIN

E

10~

GFIGFI

WP

B1-24

WH-1

MECH. /

STOR.

OU

IU

EPEP

EPEP

SS

NORTH

PROJECT

SCALE: 1/8" = 1'-0"

MECH FLOOR PLAN

A

B

C

17 18 19 20

F

D

E

G

H

J

K

L

N

M

O

P

R

1 2 43 5 6 87 9 10 11 12 13 14 15 16

DECA LOG #

DRAWING NO.

AS BUILT DATE

FRANKFORT, KENTUCKY

DIVISION OF ENGINEERING AND CONTRACT ADMINISTRATION

DEPARTMENT FOR FACILITIES AND SUPPORT SERVICES

FINANCE AND ADMINISTRATION CABINET

COMMONWEALTH OF KENTUCKYACCOUNT NO.

DATEDESCRIPTION OF REVISIONS

REVISION HISTORY OF THIS DRAWING

DATEDESCRIPTION OF REVISIONS

A&E FILE NO. 24619

DRAWING DATE 05/07/2025

DRAWN BY

CHECKED BY

PHASE RTA

RTA DATE

DRAWING INFORMATION

KSP POST NO. 3 - HVAC UPGRADES

3119 NASHVILLE ROAD, BOWLING GREEN KY

520-CBZ6-BG02-00

05/23/2025

Paducah, KY Office

2301 McCracken Blvd Paducah, KY 42001

270-444-9274 MarcumEngineering.net

BA/MM

BY/AD ME1.1

MECH-ELEC FLOOR PLAN

MECHANICAL

CONSTRUCTION TAG NOTES

(APPLIES TO THIS DRAWING ONLY)

RETURN AIR DUCT TO RISE FROM UNIT CONNECTION AND INTO ATTIC. SAWCUT

OPENING IN EXISTING CEILING/ROOF FOR DUCT TO PASS THROUGH INTO ATTIC

SPACE AND. COORDINATE LOCATION OF OPENING WITH EXISTING CONDITIONS

AND STRUCTURE.

2 DUCT MAINS ROUTED IN ATTIC.

SUPPLY AIR DUCT TO RISE TO ATTIC SPACE THROUGH EXISTING OPENING DUCT

INSULATION SHALL BE CONTINUOUS THROUGH OPENING. MODIFY OPENING AS

REQUIRED FOR NEW DUCTSIZE.

4 INSTALL 10x10 SA CONNECTION ON TOP OF DUCT AND CONNECT TO EXISTING

DUCT IN ATTIC.

5 INSTALL 12x10 SA CONNECTED TO EXISTING 12x10 SA DUCT ROUTED AND CONNECTED TO EXISTING 20x14 SA.

INSTALL 10x8 RA THROUGH EXISTING ROOF/CEILING TO ATTIC. CONTRACTOR

SHALL SAW CUT OPENING TO ALLOW INSULATION TO PASS THROUGH

CONTINUOUS.

INSTALL 8x8 RA THROUGH EXISTING ROOF/CEILING TO ATTIC. CONTRACTOR

SHALL SAW CUT OPENING TO ALLOW INSULATION TO PASS THROUGH

CONTINUOUS.

INSTALL 12x10 RA THROUGH EXISTING ROOF/CEILING AT ATTIC. CONTRACTOR

SHALL SAW CUT OPENING TO ALLOW INSULATION TO PASS THROUGH

CONTINUOUS.

9 MAINTAIN AREA CLEAR OF DUCTWORK FOR ACCESS TO ATTIC.

ROUTE NEW NATURAL GAS PIPING FROM FURNACES TO EXISTING PIPING

BRANCHES. MODIFY EXISTING PIPING ROUTING AS NECESSARY TO PERFROM

NEW WORK.

FURNISH AND INSTALL WATER HEATER. LOCATE WHERE PREVIOUS UNIT WAS

REMOVED. RECONNECT TO EXISTING PIPING AT CEILING. REFER TO DETAILS

FOR ADDITIONAL REQUIREMENTS.

ROUTE FURNACE CONDENSATE PIPING TO MECHANICAL ROOM FLOOR DRAIN.

MAINTAIN ADEQUATE SLOPE FOR PIPING. REFER TO DETAILS FOR MORE

INFORMATION.

NORTH

PROJECT

SCALE: 1/2" = 1'-0"

MECHANICAL ROOM FLOOR PLAN

ELECTRICAL

CONSTRUCTION TAG NOTES

(APPLIES TO THIS DRAWING ONLY)

PROVIDE AND INSTALL WIRE AND EMT CONDUIT FROM NEAREST JUNCTION BOX

TO RECONNECT EXHAUST FAN TO EXISTING CIRCUIT. SEE M5.1 EQUIPMENT

CONNECTION SCHEDULE FOR WIRE, CONDUIT AND BREAKER SIZE.

PROVIDE AND INSTALL WIRE AND EMT CONDUIT FROM NEAREST JUNCTION BOX

TO RECONNECT FURNACE TO EXISTING WIRE AND CIRCUIT. PROVIDE CIRCUIT

BREAKER OF SIMILAR TYPE TO PANEL B CIRCUITS 1,2,3, AND 4. SEE M5.1

EQUIPMENT CONNECTION SCHEDULE FOR WIRE, CONDUIT AND BREAKER SIZE.

PROVIDE AND INSTALL A DISCONNECT SWITCH FOR CONDENSING UNIT. USE THE

SAME LOCATION FROM THE REMOVED DISCONNECT. PATCH AND SEAL ANY

EXPOSED OPENING. CONNECT DISCONNECT TO CONDENSING UNIT. SEE M5.1

EQUIPMENT CONNECTION SCHEDULE FOR WIRE, CONDUIT, DISCONNECT SIZE.

PROVIDE AND INSTALL A CIRCUIT BREAKER OF SIMILAR TYPE IN PANEL B1

CIRCUIT( 5,7) IN PLACE OF THE REMOVED 3 POLE BREAKER. PLACE A BLANK

COVER OVER THE REMAINING OPEN SPOT. UPDATE THE PANEL SCHEDULE.

PROVIDE AND INSTALL WIRE AND EMT CONDUIT FROM PANEL B1 TO DISCONNECT.

SEE M5.1 EQUIPMENT CONNECTION SCHEDULE FOR WIRE, CONDUIT BREAKER

SIZE.

PROVIDE AND INSTALL A 2P CIRCUIT BREAKER OF SIMILAR TYPE IN PANEL B1 IN

PLACE OF THE REMOVED 3 POLE BREAKER. PLACE A BLANK COVER OVER THE

REMAINING OPEN SPOT. UPDATE THE PANEL SCHEDULE. PROVIDE AND INSTALL

WIRE AND EMT CONDUIT FROM PANEL B1 TO DISCONNECT. SEE M5.1 EQUIPMENT

CONNECTION SCHEDULE FOR WIRE, CONDUIT BREAKER SIZE.

6 NO ELECTRICAL WORK TO BE COMPLETED IN AREA.

7 RECONNECT INDOOR AND OUTDOOR UNIT TO EXISTING WIRE AND CIRCUIT.

8 EXISTING LIGHT SWITCH SHALL CONTINUE TO CONTROL EXHAUST FAN AND

LIGHTS.

PROVIDE, INSTALL AND CONNECT A LINE VOLTAGE, CEILING MOUNTED

OCCUPANCY SENSOR TO CONTROL EXHAUST FAN. LIGHTS SHALL CONTINUE TO

BE CONTROLLED BY LIGHT SWITCH IN ROOM.

PROVIDE AND INSTALL ALL WIRE AND EMT CONDUIT FROM SOURCE BACK TO

EQUIP. PROVIDE AND INSTALL A 3P BREAKER OF SIMILAR KIND. MOVE CIRCUIT

BREAKERS AS NEEDED TO PROVIDE SPACE FOR BREAKER IF IT DOES NOT

ALREADY EXIST. SEE ME5.1 FOR BREAKER SIZE AND WIRE SIZE.

11 PROVIDE AND INSTALL ALL WIRE AND EMT CONDUIT FROM SOURCE BACK TO

EQUIP. SEE ME5.1 FOR BREAKER SIZE AND WIRE SIZE.

PROVIDE AND INSTALL A SURFACE MOUNT RECEPTACLE IF NO SERVICE OUTLET

IS ALREADY PRESENT WITHIN 25'. CORE DRILL THROUGH WALL TO CONTINUE

CIRCUIT TO PANEL.

PROVIDE AND INSTALL WIRE AND CONDUIT FROM NEAREST JUNCTION BOX BACK

TO THE WATER HEATER. REPLACE BREAKER WITH SIMILAR KIND 2P30.SEE

DRAWING ME5.1 FOR WIRE AND CONDUIT SIZE.

PROVIDE AND INSTALL WIRE AND RMT CONDUIT FROM NEAREST JUNCTION BOX

TO RECONNECT SPLIT HEAT PUMP TO EXISTING CIRCUIT. SEE M5.1 EQUIPMENT

CONNECTION SCHEDULE FOR WIRE, CONDUIT AND BREAKER SIZE. REPLACE

CURRENT BREAKER WITH A 2P30 OF SIMILAR KIND IN PANEL.

PROVIDE AND INSTALL A DISCONNECT SWITCH FOR SPLIT HEAT PUMP UNIT. USE

THE SAME LOCATION FROM THE REMOVED DISCONNECT. PATCH AND SEAL ANY

EXPOSED OPENING. CONNECT DISCONNECT TO SPLIT HEAT PUMP. SEE M5.1

EQUIPMENT CONNECTION SCHEDULE FOR WIRE, CONDUIT, DISCONNECT SIZE.

NORTH

PROJECT

SCALE: 1/8" = 1'-0"

ELEC FLOOR PLAN

A

ME1.1

A

ME1.1

DUCT RUN-OUT

SCHEDULE

CFM RANGE SIZE

0 - 100 6"Ø

101 - 200 8"Ø 201 - 375 10"Ø 376 - 600 12"Ø

CIVIL

CONSTRUCTION TAG NOTES

(APPLIES TO THIS DRAWING ONLY)

1 EXISTING PATIO AND SIDE WALK TO REMAIN AND BE PROTECTED.

CONTRACTOR SHALL BACKFILL AREA UNDER 14'X18' CONCRETE PAD WITH

MINIMUM 12" OF COMPACTED DGA TO OBTAIN CORRECT ELEVATION. CONCRETE

PAD SHALL BE 4" THICK AND SLOPE 1% WAY FROM THE BUILDING. ELEVATION

SHALL MATCH EXISTING PATIO TOP OF CONCRETE.

INSTALL #4 REBAR ON 18" CENTERS ALONG CONNECTION OF NEW PAD TO

EXISTING PATIO. REBAR SHALL BE DOWELLED INTO EXISTING PATIO 6" AND

CENTERED IN EXISTING CONCRETE THICKNESS.

4 INSTALL THICKENED SLAB ALONG THE EDGE WHERE INDICATED.

REPAIR ALL GRADES. REMOVE ROCKS AND DEBRIS. SEED, STRAW, AND

ESTABLISHED NEW GRASS TO MATCH EXISTING.

Addendum 2.0 6/27/25

A

B

C

17 18 19 20

F

D

E

G

H

J

K

L

N

M

O

P

R

1 2 43 5 6 87 9 10 11 12 13 14 15 16

DECA LOG #

DRAWING NO.

AS BUILT DATE

FRANKFORT, KENTUCKY

DIVISION OF ENGINEERING AND CONTRACT ADMINISTRATION

DEPARTMENT FOR FACILITIES AND SUPPORT SERVICES

FINANCE AND ADMINISTRATION CABINET

COMMONWEALTH OF KENTUCKYACCOUNT NO.

DATEDESCRIPTION OF REVISIONS

REVISION HISTORY OF THIS DRAWING

DATEDESCRIPTION OF REVISIONS

A&E FILE NO. 24619

DRAWING DATE 05/07/2025

DRAWN BY

CHECKED BY

PHASE RTA

RTA DATE

DRAWING INFORMATION

KSP POST NO. 3 - HVAC UPGRADES

3119 NASHVILLE ROAD, BOWLING GREEN KY

520-CBZ6-BG02-00

05/23/2025

Paducah, KY Office

2301 McCracken Blvd Paducah, KY 42001

270-444-9274 MarcumEngineering.net

BA/MM

BY/AD ME4.1

MECH-ELEC DETAILS

FURNACE INSTALLATION DETAIL

NO SCALE

UNION

SUPPLY

AIR DUCT

COMBUSTION

AIR INTAKE

EXHAUST

VENT

REFRIGERANT

COIL

REFRIGERANT PIPING

INSULATE LINES PER

SPECIFICATIONS

RETURN AIR DUCT

P-TRAP REFER TO DETAIL

CONTROL WIRING IN CONDUIT

FURNACE

FILTER RACK

GAS MAIN

PIPING

GAS PIPING. REFER

TO PLUMBING

DRAWINGS.

FULL SIZE

GAS COCK

DIRT LEG

CAP

REDUCED TO UNIT

CONNECTION SIZE

CONCRETE MAINTENANCE

PAD. REFER TO HVAC NOTES

FOR REQUIREMENTS.

MCONTROL DAMPER CONTROL

WIRING INTERLOCKED WITH

WALL MOUNT CO2 SENSOR

MANUAL

VOLUME

DAMPER

OUTSIDE AIR DUCT

CONTROL DAMPER

FULL-SIZE CONDENSATE DRAIN

ROUTE TO OPEN RECEPTACLE.

REFER TO PLUMBING DRAWINGS

NOTE:

ORIENTATION AND CONNECTION POINTS

MAY VARY. REFER TO HVAC PLANS AND

SCHEDULES.

CONTRACTOR SHALL FURNISH AND

PLACE CONCRETE SPLASH BLOCK

2"

SLEEVE AND SEAL COPPER CONDENSATE

DRAIN PIPING THRU WALL AND TURN

DOWN TO WITHIN 6" OF GRADE

TERMINATE CONDENSATE IN

SPLASH BLOCK ON GRADE

CONDENSATE DRAIN TERMINATION DETAIL

NO SCALE

SEE CONDENSATE

DRAIN TRAP DETAIL

TRANSITION FROM PVC

TO COPPER PRIOR TO

WALL PENETRATION

B D

A C

CONDENSATE DRAIN TRAP DETAIL

NO SCALE

HVAC

UNIT

1" PVC LINE OR MATCH CONN. SIZE

IF GREATER THAN 1"

ROUTE CONDENSATE DRAIN TO HEADER, FLOOR DRAIN, OR

GRADE AS INDICATED ON DRAWINGS

NOTE:

1. "RUNNING" TRAPS ARE NOT ACCEPTABLE.

2. EXTERNAL TRAP NOT REQUIRED IF INTERNAL TRAP IS PROVIDED BY EQUIPMENT MANUFACTURER.

PIPE PLUG (TYP.)

UNION

SLOPE

SLOPETEE (TYP.)

POSITIVE UNIT PRESSURE

C= 1" + FAN TSP

D= 1" MTN.

NEGATIVE UNIT PRESSURE

A= 1/2 (B)

B= 1" + FAN TSP

HORIZONTAL INSTALLATION

SIDE VIEW

HORIZONTAL PIPE

VERTICAL INSTALLATION

REFRIGERANT PIPE SUPPORT DETAIL

NO SCALE

CEILING. REFER TO

ARCHITECTURAL

DRAWINGS.

SECURE PIPE

SUPPORT TO

WALL.

WALL. REFER TO

ARCHITECTURAL AND

STRUCTURAL

DRAWINGS.

SECURE TO

STRUCTURE.

12" MIN.

SCH. 40 PVC PIPE

(TYPICAL)

REFRIGERANT PIPING

AND INSULATION

CONTINUOUS

THROUGH SLEEVE

SECURE PIPE SLEEVE

TO SUPPORT

SECURE TO

STRUCTURE.

UNI-STRUT OR OTHER

APPROVED PIPE CLAMP

ALL-THREAD

ROD

INSULATION

CONTINUOUS

THROUGH

SLEEVE (TYP.)

UNI-STRUT OR OTHER

APPROVED SUPPORT

REFRIGERANT PIPING

AND INSULATION

SECURE PIPE SLEEVE

TO SUPPORT

CARBON STEEL, STRUT

MOUNT, INSULATION

COUPLING CLAMP EQUAL

TO KLO-SHURE INSULATION

COUPLINGS

VERTICAL INSTALLATION

WALL. REFER TO

ARCHITECTURAL AND

STRUCTURAL

DRAWINGS.

OPTIONAL

STRUT MOUNT

SADDLE-SHAPED

PIPE SUPPORT

SECURE PIPE SLEEVE

TO SUPPORT

REFER TO PLANS FOR

QUANTITY OF LINE SETS

CONDENSING UNIT SPLIT SYSTEM

NO SCALE

REFRIGERANT SUPPLY & RETURN

LINES TO A/C COIL

4" HOUSE KEEPING PAD

COIL WITH GRILLE

CONDENSING OUTDOOR UNIT

ELECTRICAL CONNECTION TO

WEATHERPROOF FUSED

DISCONNECT BY ELECTRICIAN

SUSPEND EXHAUST FAN

FROM STRUCTURE WITH

THREADED ROD AND

VIBRATION ISOLATORS.

CEILING EXHAUST FAN WITH REMOVEABLE

EXHAUST GRILLE FOR ACCESS TO AND SERVICE

OF BLOWER ASSEMBLY.

DUCTWORK - SEE PLANS

FOR SIZE.

CEILING MOUNTED EXHAUST FAN DETAIL

NO SCALE

FLEX CONNECTOR

BACKDRAFT DAMPER

LAY-IN OR GYP.

CEILING ASSEMBLY

RETURN-AIR GRILLE PLENUM DETAIL

NO SCALE

NOTE:

1. FLEXIBLE DUCT SHALL NOT

BE USED TO CONNECT

GRILLES TO DUCT.

RETURN AIR DUCT

(SEE PLAN FOR SIZE)

RETURN AIR DUCT

(SEE PLAN FOR SIZE)

FULL SIZE INTERNALLY

INSULATED PLENUM

CEILING (SEE

ARCHITECTURAL)

RETURN AIR GRILLE

(SEE SCHEDIULE)

" M

IN

L

W

45°

L = 1/4 W

(4" MIN.)

RECTANGLE TAKE-OFF

NOTE:

SPIN-INS, RAKE-OFFS,

EXTRACTORS, SPLITTERS, ETC.

WILL NOT BE ACCEPTED

UNLESS OTHERWISE NOTED.

AIR FLOW

SUPPLY AIR TRUNK DUCT

SUPPLY AIR DUCT TAKE-OFF CONNECTION DETAIL

NO SCALE

TAPE VAPOR BARRIER OF

FLEXIBLE DUCT TO METAL

DUCT OR DIFFUSER BACK

VAPOR BARRIER WITH FOIL

BACK TAPE

VOLUME DAMPER W/

HANDLE STAND-OFF

EXTERNALLY INSULATED ROUND

DUCT (SEE PLAN FOR SIZE AND

LENGTH OF RUN)

1" GASKETED FLANGE

45° TAKE-OFF

CONNECT FLEXIBLE

DUCT TO FITTING W/

METAL CLAMP

CEILING DIFFUSER

WITH DIFFUSER BACK

INSULATION (SEE PLAN

FOR SIZE AND TYPE)

INSULATED FLEXIBLE

DUCT 5'-0" MAX LENGTH

SEE PLAN FOR SIZE

LONG RADIUS, HARD

ELBOW TO BE INSTALLED

BEFORE FLEXIBLE DUCT

ATTACH 1/4" SELF-LOCKING

PLASTIC CABLE TIE WITH

TWO(2) SHEETMETAL

SCREWS TO SHEETMETAL

DUCTWORK

ROUND TAKE-OFF

AIR FLOW

SUPPLY AIR TRUNK DUCT

ELECTRICAL EQUIPMENT LABEL/IDENTIFICATION

NO SCALE

3"

LETTERING SIZE = 12 PT.

2"

EQUIPMENT DESIGNATION:

SERVED BY:

CIRCUIT NO:

LOCATION:

LOAD SERVED

VOLTAGE:

AF

W

LAMICOID EQUIPMENT LABEL

EQUIPMENT

ENCLOSURE

ARC FLASH WARNING

LABEL

SHOCK HAZARD WARNING

SIGN

LAST METHOD IS TO SURFACE

MOUNT WIREMOLD AND BOX TO

FINISHED INTERIOR WALL. THIS

METHOD SHALL BE USED ONLY IF THE

OTHER TWO METHODS ARE NOT

POSSIBLE.

EXISTING WALL

FINISHED FLOOR

CONDUIT ROUTING/INSTALLATION

THIRD METHOD DETAIL

NO SCALE

FIRST METHOD IS TO EMBED DEVICE

HANDY BOX AND CONDUIT INTO NEW

OR EXISTING INTERIOR WALL WHERE

POSSIBLE

NEW OR EXISTING WALL

FINISHED FLOOR

SURFACE MOUNT CONDUIT IN UTILITY

AREA AND THEN THROUGH WALL TO

BOX

SURFACE MOUNT

CONDUIT/WIREMOLD AND HANDY BOX

TO FINISHED INTERIOR WALL. THIS

METHOD SHALL BE USED ONLY IF THE

FIRST METHOD IS NOT POSSIBLE.

EXISTING WALL

FINISHED FLOOR

UTILITY AREA SIDE WHEN AVAILABLE

(IE: STORAGE,

MECHANICAL/ELECTRIC EQUIPMENT

ROOMS AND JANITORIAL AREAS)

CONDUIT ROUTING/INSTALLATION

FIRST METHOD DETAIL

NO SCALE

CONDUIT ROUTING/INSTALLATION

SECOND METHOD DETAIL

NO SCALE

COLD WATER IN

THERMAL EXPANSION

TANK

COLD WATER

SHUT-OFF VALVE

HOT WATER OUT

TEMPERATURE

AND PRESSURE

HOT WATER

WATER HEATER

DIELECTRIC UNION (TYP.)

SHUT-OFF VALVE

CHECK VALVE

THERMOMETER

RELIEF VALVE

ELECTRIC WATER HEATER DETAIL

NO SCALE

4" THICK CONCRETE

MAINTENANCE PAD

16 GAUGE GALVANIZED

AUXILIARY DRAIN PAN

INSTALL FOR ALL

INSTALLATION ABOVE

CEILINGS OR ON EQUIP.

MEZZANINES ABOVE

CEILINGS

RUN RELIEF VALVE

PIPING TO FLOOR

DRAIN, MOP SINK OR

TO WITHIN 6" OF

OUTSIDE GRADE

INSTALL DRAIN LINE WITH

SHUT-OFF VALVE ROUTE

LINE TO SUITABLE DRAIN

WHERE POSSIBLE

NOTE:

WHEN WATER HEATERS ARE INSTALLED

IN PARALLEL, THE PIPES FROM THE TEE

TO EACH WATER HEATER SHALL BE OF

EQUAL LENGTH FOR BOTH COLD AND

HOT WATER PIPE.

INDOOR WALL MOUNTED

MINI SPLIT UNIT BY M.C.

CEILING SYSTEM

SPREADER BAR BY E.C.

WIRING AND EMT CONDUIT EXTENDING

TO OUTDOOR UNIT, ROUTE WITH PIPING

ABOVE CEILING, BY E.C.

30 AMP, 600 VOLT, DOUBLE POLE,

SINGLE PHASE AC MANUAL MOTOR

CONTROLLER, SUITABLE AS

MOTOR DISCONNECT, TOGGLE,

INDUSTRIAL GRADE, WHITE WITH

WHITE FACE PLATE, FLUSH IN

CEILING, BY E.C. (LEVITON CAT. #

MS302-DSW OR EQUAL)

M.C. CABLE BY E.C. ROUTED

TO UNIT WITH PIPING

COORDINATE

SURFACE MOUNTED

PIPING AND CABLE

COVER BY M.C.

NOTE:

a. COORDINATE ALL WORK WITH M.C.

b. LABEL TOGGLE SWITCH WITH

OUTDOOR UNIT DESIGNATION

WHEN PIPING ENTERS FROM BACK,

EXTEND MC THROUGH 2-PIECE SURFACE

MOUNTED RACEWAY FROM CEILING TO

UNIT, ALLOW SPACE FOR T'STAT WIRING

INDOOR MINI-SPLIT DETAIL

NO SCALE

Addendum 2.0 6/27/25

AutoCAD SHX Text

A

B

C

17 18 19 20

F

D

E

G

H

J

K

L

N

M

O

P

R

1 2 43 5 6 87 9 10 11 12 13 14 15 16

DECA LOG #

DRAWING NO.

AS BUILT DATE

FRANKFORT, KENTUCKY

DIVISION OF ENGINEERING AND CONTRACT ADMINISTRATION

DEPARTMENT FOR FACILITIES AND SUPPORT SERVICES

FINANCE AND ADMINISTRATION CABINET

COMMONWEALTH OF KENTUCKYACCOUNT NO.

DATEDESCRIPTION OF REVISIONS

REVISION HISTORY OF THIS DRAWING

DATEDESCRIPTION OF REVISIONS

A&E FILE NO. 24619

DRAWING DATE 05/07/2025

DRAWN BY

CHECKED BY

PHASE RTA

RTA DATE

DRAWING INFORMATION

KSP POST NO. 3 - HVAC UPGRADES

3119 NASHVILLE ROAD, BOWLING GREEN KY

520-CBZ6-BG02-00

05/23/2025

Paducah, KY Office

2301 McCracken Blvd Paducah, KY 42001

270-444-9274 MarcumEngineering.net

BA/MM

BY/AD ME5.1

MECH-ELEC SCHEDULES

MECHANICAL EQUIPMENT CONNECTION SCHEDULE

ITEM # DESCRIPTION VOLTAGE/PHASE

ELEC. DATA CONDUCTORS LOCAL DISCONNECTING MEANS

REMARKS/

NOTESLOAD UNITS MCA MOCP CONDUIT LINE NEU GND N.F.D.S. SIZE F.D.S. SIZE FUSE SIZE ENCL

NEMA

F-1 FURNACE 115/1 - - 9.6 1P15 3/4" #12 #12 #12 BREAKER - - - A,D,H

F-2 FURNACE 115/1 - - 11.5 1P15 3/4" #12 #12 #12 BREAKER - - - A,D,H

F-3 FURNACE 115/1 - - 11.5 1P15 3/4" #12 #12 #12 BREAKER - - - A,D,H

F-4 FURNACE 115/1 - - 11.5 1P15 3/4" #12 #12 #12 BREAKER - - - A,D,H

HP-1 AIR COOLED HEAT PUMP 208/1 - - 20.4 2P30 3/4" #10 - #10 2P30 - - 3R A,C

HP-2 AIR COOLED HEAT PUMP 208/1 - - 20.4 2P30 3/4" #10 - #10 2P30 - - 3R A,C

HP-3 AIR COOLED HEAT PUMP 208/1 - - 20.4 2P30 3/4" #10 - #10 2P30 - - 3R A,C

HP-4 AIR COOLED HEAT PUMP 208/1 - - 20.4 2P30 3/4" #10 - #10 2P30 - - 3R A,C

HP-5 AIR COOLED HEAT PUMP 208/3 - - 11.0 3P15 3/4" #12 - #12 3P30 - - 3R A,G,F

WH-1 WATER HEATER 208/1 4500 WATTS - 2P30 3/4" #10 - #10 BREAKER - - - -

IU-1 SPLIT HEAT PUMP UNIT 208 / 1 - - 2.1 2P30 1 / 2" #10 - #10 2P30 - - NEMA 3 I,J

OU-1 SPLIT HEAT PUMP UNIT 208 / 1 - - 2.1 2P30 1 / 2" #10 - #10 2P30 - - NEMA 3R I,J

AHU-1 SPLIT AIR HANDLING UNIT 208/1 - - 41.0 2P45 3/4" #6 - #10 2P60 - - 3 A,F,G

VENTILATION EQUIPMENT CONNECTION SCHEDULE

ITEM # DESCRIPTION VOLTAGE/PHASE

ELEC. DATA CONDUCTORS UNIT OPERATION

CONTROL

REMARKS/NOTES

LOAD UNITS MCA MOCP CONDUIT LINE NEU GND OCC SWITCH

EF-1 EXHAUST FAN 115/1 13 WATTS - 1P20 3/4" #12 #12 #12 X - A,B,E

EF-2 EXHAUST FAN 115/1 39 WATTS - 1P20 3/4" #12 #12 #12 X - A,B,E

EF-3 EXHAUST FAN 115/1 13 WATTS - 1P20 3/4" #12 #12 #12 X - A,B,E

EF-4 EXHAUST FAN 115/1 13 WATTS - 1P20 3/4" #12 #12 #12 X - A,B,E

EF-5 EXHAUST FAN 115/1 7 WATTS - 1P20 3/4" #12 #12 #12 - X A,B,E

EF-6 EXHAUST FAN 115/1 13 WATTS - 1P20 3/4" #12 #12 #12 X - A,B,E

MECHANICAL AND VENTILATION GENERAL NOTES:

THE INFORMATION ABOVE SHALL BE COORDINATED WITH THE MECHANICAL EQUIPMENT AS TAGGED ACTUAL EQUIPMENT REQUIREMENTS SHALL TAKE PRESIDENCE OVER THE LISTED INFORMATION. CONTRACTOR SHALL FURNISH AND INSTALL ALL EQUIPMENT REQUIRED TO PLACE EQUIPMENT IN SERVICE. EQUIPMENT MANUFACTURER SHALL BE RESPONSIBLE FOR VARIATIONS IN ELECTRICAL FIELD CONNECTIONS DUE TO EQUIPMENT SUBSTITUTIONS - MODIFY OVERCURRENT, DISC. SW, WIRE SIZE ETC, AS NECESSARY.

2 THIS SCHEDULE INCLUDES, BUT IS NOT LIMITED TO, THE EQUIPMENT FOUND ON THIS PROJECT, COORDINATE WITH ALL TRADES AND PROVIDE MANUFACTURERS MINIMUM REQUIREMENTS TO ALL EQUIPMENT INSTALLED. THIS SCHEDULE IS NOT TO IMPLY QUANTITY OF EQUIPMENT, REFER TO CONSTRUCTION DOCUMENTS OF RESPECTIVE TRADE FOR LOCATION AND QUANTITIES.

3 STARTER/MOTOR SWITCH/DISCONNECT SHALL BE LOCATED ADJACENT TO UNIT IN ACCORDANCE WITH N.E.C. ARTICLE #110 & #440 - MAINTAIN WORKING CLEARANCES.

4 ALL FIELD WIRING TO UNITS SHALL BE PROPERLY SUPPORTED PER NEC AND ENCLOSURES SHALL BE PROPERLY RATED FOR THE INSTALLATION CONDITIONS. PROPERLY BOND AND GROUND.

5 CONTRACTOR IS RESPONSIBLE FOR INSTALLATION OF ANY EQUIPMENT SHIPPED LOOSE WITH UNIT, SUCH AS CONTROLS - INSTALL PER MANUFACTURER'S RECOMMENDATIONS.

6 EC SHALL FURNISH AND INSTALL ALL RACEWAY AND BOXES AS REQUIRED FOR THE MC FURNISHED CONTROLS. COORDINATE WITH MC BEFORE INSTALLATION.

7 EC SHALL FURNISH AND INSTALL ALL RACEWAY AND BOXES AS REQUIRED FOR THE MC FURNISHED LINE VOLTAGE CONTROLS. EC TO RECEIVE DEVICES, FURNISH AND INSTALL ALL WIRING AND CONDUIT. LINE

VOLTAGE DEVICE SHALL BE INSTALLED BY EC. COORDINATE WITH MC BEFORE INSTALLATION.

UNIT OPERATION CONTROL:

OCC. UNIT SHALL BE CONTROLLED BY ZONE LIGHT CONTROL. COORDINATE INTERCONNECTION OF FAN TO LIGHTING POWER CIRCUIT WITH THE ELECTRICAL CONTRACTOR

SWITCH SWITCH - UNIT SHALL BE CONTROLLED BY INDEPENDENT PILOT LIT SWITCH. ELECTRICAL CONTRACTOR SHALL FURNISH AND INSTALL PILOT LIGHT SWITCH. SWITCH SHALL BE ILLUMINATED WHEN FAN IS ENERGIZED.

SPECIAL NOTES:

A UNIT PROVIDED WITH THERMAL OVERLOAD PROTECTION.

B PROVIDE UNIT WITH FACTORY WIRED, PLUG-TYPE DISCONNECT.

C ELECTRICAL CONTRACTOR SHALL FURNISH AND INSTALL ELECTRICAL DISCONNECTS FOR UNIT(S).

D EQUIPMENT SHORT-CIRCUIT CURRENT RATING (SCCR) SHALL BE EQUAL TO, OR GREATER THAN THE MINIMUM AS SCHEDULED. EQUIPMENT NAME PLATE SHALL INCLUDE SCCR IN ACCORDANCE WITH THE NATIONAL ELECTRICAL CODE 2017 440.4(B). SCCR SHALL BE PROVIDED FOR ENGINEERING REVIEW ON EQUIPMENT SHOP DRAWING SUBMITTALS.

E ELECTRICAL CONTRACTOR SHALL INSTALL SPEED CONTROLLER FOR FAN. HVAC CONTRACTOR SHALL PROVIDE CONTROLLER. FIELD COORDINATE LOCATION OF CONTROLLER ADJACENT TO UNIT.

F ELECTRICAL CONTRACTOR SHALL FURNISH AND INSTALL ELECTRICAL DISCONNECTS SWITCH WITH A SINGLE POINT CONNECTION.

G EQUIPMENT SHORT-CIRCUIT CURRENT RATING (SCCR) SHALL BE EQUAL TO, OR GREATER THAN THE MINIMUM AS SCHEDULED. EQUIPMENT NAME PLATE SHALL INCLUDE SCCR IN ACCORDANCE WITH THE NATIONAL ELECTRICAL CODE 2017 440.4(B). SCCR SHALL BE PROVIDED FOR ENGINEERING REVIEW ON EQUIPMENT SHOP DRAWING SUBMITTALS.

H LOCAL CIRCUIT BREAKER SHOULD SERVE AS A DISCONNECTING MEANS FOR UNIT.

I ELECTRICAL CONTRACTOR SHALL FURNISH AND INSTALL ELECTRICAL DISCONNECT SWITCH FOR INDOOR AND OUTDOOR UNIT.

J INDOOR UNIT SHALL BE POWERED BY OUTDOOR UNIT.

FURNACE SCHEDULE

MARK MFG. MODEL TYPE CONFIG.

SIZE

(TONS)

SUPPLY

AIRFLOW

(CFM)

MAX OA

AIRFLOW

(CFM)

EXT. S.P.

(IN H2O) DRIVE

FAN DATA NATURAL GAS FIRED FURNACE DATA

COND. UNIT REMARKS AND

ACCESSORIES MARKMOTOR

(HP)

VOLTAGE/

PHASE

MCA

(AMPS)

MOCP

(AMPS)

INPUT

(MBH)

OUTPUT

(MBH)

MIN. EFF.

FLUE

SIZE

(INCHES)

F-1 YORK Y92E VERTICAL 3.0 1,000 100 0.75 DIRECT 1/2 115 / 1 8.8 15 60.0 58.0 97% 3 HP-1 SEE BELOW F-1

F-2 YORK Y92E VERTICAL 3.0 1,200 120 0.75 DIRECT 1/2 115 / 1 8.8 15 80.0 77.0 97% 3 HP-2 SEE BELOW F-2

F-3 YORK Y92E VERTICAL 3.0 1,200 120 0.75 DIRECT 1/2 115 / 1 8.8 15 80.0 77.0 97% 3 HP-3 SEE BELOW F-3

F-4 YORK Y92E VERTICAL 3.0 1,200 120 0.75 DIRECT 1/2 115 / 1 8.8 15 80.0 77.0 97% 3 HP-4 SEE BELOW F-4

REMARKS AND ACCESSORIES

1 PROVIDE UNIT WITH A MINIMUM TEN (10) YEAR HEAT EXCHANGER WARRANTY AND A ONE (1) YEAR PARTS AND LABOR WARRANTY.

2 PROVIDE UNIT WITH MATCHING CASED DX COOLING COIL BY FURNACE MANUFACTURER. PROVIDE A FACTORY INSTALLED, INTERNALLY MOUNTED TXV FOR DX COOLING COIL.

3 PROVIDE UNIT WITH A FACTORY-FABRICATED, HINGED FILTER RACK FLANGE-MOUNTED TO THE UNIT RETURN TO ACCEPT STANDARD NOMINAL SIZE (12" X 24" OR 24" X 24"), 2" THICK, MERV 13 AIR FILTERS. UNIT SHALL HAVE A GASKETED DOOR AND RAILS FOR EASY FILTER CHANGING. (BLC INDUSTRIES CLEAN-LINE SERIES 05FB OR APPROVED EQUAL). PROVIDE AN EXTRA SET OF REPLACEMENT FILTERS UPON PROJECT SUBSTANTIAL COMPLETION.

4 MAINTAIN MANUFACTURER'S MINIMUM CLEARANCES.

5 PROVIDE UNIT WITH VARIABLE SPEED, CONSTANT AIRFLOW ECM MOTOR.

6 PROVIDE UNIT WITH DRAIN SENSOR THAT SHUTS DOWN THE INDOOR UNIT ANY TIME A CLOGGED CONDENSATE DRAIN IS DETECTED IN THE DRAIN PAN.

7 PROVIDE UNIT SUITABLE FOR SEALED COMBUSTION OPERATION.

8 ELECTRICAL CONTRACTOR SHALL FURNISH AND INSTALL NON-FUSED ELECTRICAL DISCONNECT SWITCH.

9 MECHANICAL CONTRACTOR SHALL PROVIDE UNIT WITH MANUFACTURER'S 7-DAY PROGRAMMABLE THERMOSTAT.

10 MECHANICAL CONTRACTOR SHALL SIZE AND PROVIDE UNIT WITH A NEEDLE-POINT IONIZATION DEVICE (GLOBAL PLASMA SOLUTIONS OR EQUAL). DEVICE SHALL BE PROVIDED AT 24V, POWERED AND CONTROLLED BY THE UNIT. IONIZATION DEVICE SHALL BE

ENERGIZED WHEN THE SUPPLY FAN FOR THE UNIT IS OPERATIONAL.

11 PROVIDE UNIT WITH MANUFACTURER'S HORIZONTAL CONCENTRIC VENT KIT.

12 COMBUSTION INTAKE AND FLUE VENT PIPING MATERIAL AND INSTALLATION SHALL BE PER MANUFACTURER'S REQUIREMENTS.

13 PROVIDE UNIT WITH 2-STAGE AUXILIARY NATURAL GAS HEAT. AUXILIARY NATURAL GAS HEAT SHALL ONLY BE ENERGIZED WHEN HEAT PUMP OPERATIONS ARE INADEQUATE TO MAINTAIN TEMPERATURE SET POINT DURING HEATING CONDITIONS.

CARRIER, DAIKIN, TRANE, YORK, OR APPROVED EQUAL

AIR COOLED HEAT PUMP UNIT SCHEDULE

MARK MFG. MODEL SIZE

WEIGHT

(LBS.)

TOTAL

COOLING

CAP.

(MBH)

SENSIBLE

COOLING

CAP.

(MBH)

EER @

DESIGN

HEATING

CAP.

(MBH)

HOT GAS

REHEAT

CAP.

(MBH)

HSPF @

DESIGN

VOLTAGE/

PHASE

MCA

(AMPS)

MOCP

(AMPS)

SCCR

(KA) SERVICE REMARKS AND

ACCESSORIES MARK

HP-1 YORK YH6 36 270 35.4 26.8 11.7 18.6 -- 8.1 208 / 1 20.4 30 -- F-1 1-11,16 HP-1

HP-2 YORK YH6 36 270 35.4 26.8 11.7 18.6 -- 8.1 208 / 1 20.4 30 -- F-2 1-11,16 HP-2

HP-3 YORK YH6 36 270 35.4 26.8 11.7 18.6 -- 8.1 208 / 1 20.4 30 -- F-3 1-11,16 HP-3

HP-4 YORK YH6 36 270 35.4 26.8 11.7 18.6 -- 8.1 208 / 1 20.4 30 -- F-4 1-11,16 HP-4

HP-5 AAON CFA 002 370 21.3 14.0 22.2 13.9 11.5 -- 208 / 3 11.0 15 10 AHU-1 1-10,12-16 HP-5

REMARKS AND ACCESSORIES:

1 PROVIDE UNIT WITH AT MINIMUM ONE (1) YEAR PARTS WARRANTY, ONE (1) YEAR LIMITED LABOR WARRANTY, AND FIVE (5) YEAR COMPRESSOR WARRANTY.

2 COOLING CAPACITIES ARE BASED ON 95 Fdb OUTDOOR AMBIENT TEMPERATURE AND 75 Fdb INDOOR TEMPERATURE.

3 HEATING CAPACITIES ARE BASED ON 0 Fdb OUTDOOR AMBIENT TEMPERATURE AND 70 Fdb INDOOR TEMPERATURE.

4 PROVIDE UNIT WITH LOW PRESSURE SWITCH, HIGH PRESSURE SWITCH, CRANKCASE HEATER, SUCTION PRESSURE TRANSDUCER, AND EVAPORATOR FREEZE THERMOSTAT.

5 PROVIDE UNIT WITH FACTORY INSTALLED THERMAL EXPANSION VALVE (TXV), REVERSING VALVE, AND FILTER DRYER.

6 PROVIDE UNIT WITH AT MINIMUM TWO-STAGE COMPRESSOR.

7 PROVIDE UNIT WITH HAIL GUARD ON CONDENSER COIL(S).

8 PROVIDE UNIT WITH THERMAL OVERLOAD PROTECTION.

9 PROVIDE UNIT WITH REFRIGERANT HAVING A GLOBAL WARMING POTENTIAL LESS THAN 700 IN ACCORDANCE WITH CURRENT US EPA REGULATIONS.

10 FURNISH AND INSTALL REFRIGERANT PIPING SIZED AND ROUTED PER MANUFACTURER'S RECOMMENDATIONS.

11 HEAT PUMP UNIT SHALL BE FURNISHED BY FURNACE MANUFACTURER.

12 EQUIPMENT SHORT-CIRCUIT CURRENT RATING (SCCR) SHALL BE EQUAL TO, OR GREATER THAN THE MINIMUM AS SCHEDULED. EQUIPMENT NAME PLATE SHALL INCLUDE SCCR IN ACCORDANCE WITH THE NATIONAL ELECTRICAL CODE 2017 440.4(B). SCCR

SHALL BE PROVIDED FOR ENGINEERING REVIEW ON EQUIPMENT SHOP DRAWING SUBMITTALS.

13 UNIT SHALL BE FURNISHED BY INDOOR HEAT PUMP AIR HANDLING UNIT MANUFACTURER.

14 PROVIDE UNIT WITH FULLY MODULATING HOT GAS REHEAT COIL AND CONTROL.

15 PROVIDE UNIT WITH ELECTRICAL PHASE LOSS PROTECTION.

16 ELECTRICAL CONTRACTOR SHALL FURNISH AND INSTALL ELECTRICAL DISCONNECT.

HP-1/2/3/4: CARRIER, DAIKIN, TRANE, YORK, OR APPROVED EQUAL / HP-5: AAON, UNITED COOL AIR, SAMSUNG, OR APPROVED EQUAL

LOUVER SCHEDULE

MARK MFG. DESCRIPTION MODEL/

TYPE

SIZE

(INCHES)

AIRFLOW

(CFM)

FREE

AREA

(SQ. FT.)

FACE

VELOCITY

(FPM)

PRESSURE

DROP

(IN. H2O)

TYPE OF FRAME

AND MOUNTING

MOUNTING

HEIGHT

(FT-IN)

SERVICE REMARKS AND

ACCESSORIES MARK

L-1 GREENHECK FIXED BLADE LOUVER ESD-435 24 X 16 X 4 400 0.99 404 0.03 CHANNEL 9'-4" AHU-1 INTAKE SEE BELOW L-1

REMARKS AND ACCESSORIES:

1 MOUNTING HEIGHT MEASURED FROM BOTTOM OF LOUVER TO TOP OF FINISHED FLOOR. CONTRACTOR SHALL COORDINATE LOUVER INSTALLATION WITH SOLDIER COURSE BRICK BAND AND EXISTING EXHAUST

LOUVER ELEVATION.

2 SIZES ARE SPECIFIED AS: FIRST FIGURE-WIDTH, SECOND FIGURE-HEIGHT, AND THIRD FIGURE- DEPTH.

3 PROVIDE UNIT WITH EXTENDED SILL.

4 PROVIDE UNIT IN ALUMINUM CONSTRUCTION.

5 PROVIDE UNIT WITH ALUMINUM BIRD SCREEN.

6 PROVIDE UNIT WITH FACTORY APPLIED, 2-COAT, 70% KYNAR FINISH. COLOR TO BE SELECTED BY OWNER.

7 INSTALL UNIT IN 18 GAUGE SHEETMETAL WALL SLEEVE.

8 CONTRACTOR SHALL FURNISH AND INSTALL LOOSE LINTEL AT OPENING FOR LOUVER.

GREENHECK, NCA, RUSKIN, UNITED ENERTECH, OR APPROVED EQUAL

Addendum 2.0 6/27/25

SPLIT HEAT PUMP SYSTEM EQUIPMENT SCHEDULE

INDOOR

UNIT

MARK

MFG. MODEL

NUMBER DESCRIPTION AREA SERVED

NOMINAL

(TONS)

APPROX. UNIT

WEIGHT

(LBS.)

MIN. REFRIG.

EQUIVALENT

LINE

LENGTH

(FT.)

MAX.

AIRFLOW

(CFM)

RATED

COOLING

CAPACITY

(MBH)

SEER2

RATED

HEATING

CAPACITY

(MBH)

HSPF2 VOLTAGE /

PHASE

MCA

(AMPS)

OUTDOOR

UNIT MARK MFG. MODEL

NUMBER

APPROX.

UNIT

WEIGHT

(LBS.)

ELECTRICAL DATA

REMARKS AND

ACCESSORIES

SYSTEM

MARKVOLTAGE /

PHASE

MCA

(AMPS)

MOCP

(AMPS)

SCCR

(kA)

IU-1 LG KNSAP361A HIGH WALL RADIO TECH 113 3.0 45 75 1,095 33.0 20.0 35.2 8.5 208 / 1 0.6 OU-1 LG KUSAP361A 150 208 / 1 23.0 30 5 SEE BELOW IU/OU-1

REMARKS AND ACCESSORIES:

1 PROVIDE UNIT WITH AT MINIMUM FIVE (5) YEAR PARTS WARRANTY, ONE (1) YEAR LIMITED-LABOR WARRANTY AND SEVEN (7) YEAR COMPRESSOR WARRANTY.

2 COOLING CAPACITIES BASED ON 95 F AMBIENT AIR TEMPERATURE AND 80 F db/67 F wb INDOOR AIR TEMPERATURE.

3 HEATING CAPACITIES BASED ON 47 F db AMBIENT AIR TEMPERATURE AND 70 F db/60 F wb INDOOR AIR TEMPERATURE.

4 MAINTAIN MANUFACTURER'S MINIMUM RECOMMENDED CLEARANCES.

5 FURNISH AND INSTALL REFRIGERANT PIPING SIZED AND ROUTED PER THE MANUFACTURER'S RECOMMENDATIONS. USE OF LINE SETS IS NOT ACCEPTABLE. TOTAL EQUIVALENT FOOTAGE OF LINE LENGTHS SHALL NOT EXCEED THE MANUFACTURER'S REQUIREMENTS OR THE ABOVE

SPECIFIED LENGTH, WHICHEVER IS LESS.

6 PROVIDE UNIT WITH REFRIGERANT HAVING A GLOBAL WARMING POTENTIAL LESS THAN 700 IN ACCORDANCE WITH CURRENT US EPA REGULATIONS.

7 ELECTRICAL CONTRACTOR SHALL FURNISH AND INSTALL ELECTRICAL DISCONNECTS FOR INDOOR AND OUTDOOR UNITS.

8 INDOOR UNIT SHALL BE POWERED BY OUTDOOR UNIT.

9 PROVIDE UNIT WITH WASHABLE, ANTI-MICROBIAL, LONG-LIFE AIR FILTER.

10 PROVIDE UNIT WITH MANUFACTURER'S WIRED PROGRAMMABLE THERMOSTAT CAPABLE OF CONTROLLING ALL UNIT FUNCTIONS. WIRELESS REMOTE CONTROLLER IS NOT ACCEPTABLE.

11 PROVIDE UNIT WITH LOW AMBIENT COOLING AND HEATING KIT CAPABLE OF OPERATION TO 0 Fdb.

CARRIER, DAIKIN, LG, MITSUBISHI, TRANE, OR APPROVED EQUAL

Sheet No.

Sheet Title

Checked By:

Drawn By :

Issue Date:

Project No.:

XH01

ATTIC OPENING

STRUCTURAL

SUPPORT

24619

6/30/2025

BCA

BCA

KS

P P

OS

T 3

- H

VA

C

UP

GR

AD

ES

N

AS

HV

ILL

E

RO

AD

, B

OW

LIN

G

GR

EE

N, K

EN

TU

CK

Y

DO NOT REPRODUCE

This document contains confidential information and is an instrument of service and property of the Engineer. It shall not be used on other projects or for the extension of this project without the Engineer's written approval.

Paducah, KY Office 2301 McCracken Blvd, Paducah, KY 42001 270-444-9274 / MarcumEngineering.net

MAIN RAIL

END REACTION

(TYP.)

CROSS RAIL

END REACTION

(TYP.)

QUICKFRAME ADJUSTABLE FRAME

ROOF FRAMING

RE: PLAN

ROOF FRAMING

RE: PLAN

SEE "FIELD REINFORCEMENT

OF BAR JOIST AT CONCENTRATED

LOADS" DETAIL FOR ADD'L

REQUIRED REINFORCING

QUICKFRAMES ADJUSTABLE STEEL ROOF FRAMES:

UNLESS SPECIFICALLY EXCLUDED ON PLAN, CONTRACTOR MAY PROVIDE THE FOLLOWING 12 GAGE (30 KSI) QUICKFRAMES OR 16 GAGE (30 KSI) ADJUSTABLE FRAMES AT MISCELLANEOUS OPENINGS IN STEEL ROOF FRAMING WHERE THE ROOF LIVE LOAD OR SNOW LOAD DOES NOT EXCEED 20 PSF AND THE TOTAL LOAD TO THE FRAME DOES NOT EXCEED THE LOADS SHOWN BELOW. USE THESE ADJUSTABLE FRAMES FOR OPENINGS REQUIRED BY SKYLIGHTS OR

MECHANICAL ROOFTOP UNITS.

CROSS RAIL END REACTION SHALL NOT EXCEED 1000 LBS.

MAIN RAIL END REACTION SHALL NOT EXCEED 1750 LBS.

THE TOTAL FRAME LOADS SHOWN BELOW INCLUDE A 20% INCREASE FOR MECHANICAL UNITS PER IBC SECTION 1607.8.2

AND AN INDUSTRY STANDARD UNBALANCED MECHANICAL LOADING OF 2/3 AND 1/3.

MECHANICAL LOADS

12 GAUGE FRAME

FRAME SPAN

FRAME

MAX. CROSS RAIL

OPENING SPAN

TOTAL

LOAD(LBS)

4'-0" 4'-0" 5'-0" 5'-0" 6'-0" 6'-0" 7'-0" 7'-0" 8'-0" 8'-0"

48" 96" 48" 96" 48" 96" 48" 96" 48" 96"

16 GAUGE FRAME

FRAME SPAN

FRAME

MAX. CROSS RAIL

OPENING SPAN

TOTAL

LOAD(LBS)

4'-0" 4'-0" 5'-0" 5'-0" 6'-0" 6'-0" 7'-0" 7'-0" 8'-0" 8'-0"

48" 96" 48" 96" 48" 96" 48" 96" 48" 96"

THE TOTAL FRAME LOADS SHOWN BELOW REFLECT THE MAXIMUM LOAD THE FRAME CAN CARRY WHEN ALL WEIGHT IS PLACED EVENLY ON THE MAIN RAILS AND DISTRIBUTED EVENLY BETWEEN ALL FOUR SUPPORT RAILS

EVENLY DISTRIBUTED LOADS

12 GAUGE FRAME

FRAME SPAN

FRAME

MAX. CROSS RAIL

OPENING SPAN

TOTAL

LOAD(LBS)

4'-0" 4'-0" 5'-0" 5'-0" 6'-0" 6'-0" 7'-0" 7'-0" 8'-0" 8'-0"

48" 96" 48" 96" 48" 96" 48" 96" 48" 96"

16 GAUGE FRAME

FRAME SPAN

FRAME

MAX. CROSS RAIL

OPENING SPAN

TOTAL

LOAD(LBS)

4'-0" 4'-0" 5'-0" 5'-0" 6'-0" 6'-0" 7'-0" 7'-0" 8'-0" 8'-0"

48" 96" 48" 96" 48" 96" 48" 96" 48" 96"

THESE QUICKFRAMES, OR THE OPENING THEY SPAN, SHALL NOT BE PLACED SO AS TO INTERFERE WITH THE REQUIREMENTS OF OTHER STRUCTURAL ELEMENTS (I.E. DRAG STRUTS, PURLINS, SUBPURLINS, ANGLES, ETC.) WITHOUT

THE PRIOR APPROVAL OF THE STRUCTURAL ENGINEER.

QUICKFRAMES ADJUSTABLE FRAMES SHALL BE AS MANUFACTURED BY QUICKFRAMES, A DIVISION OF SOYKO INDUSTRIES 480-464-1500 WWW.QUICKFRAMES.COM AND SHALL BE INSTALLED PER MANUFACTURER'S

RECOMMENDATIONS.

TYPICAL DETAIL

11 ADJUSTABLE FRAME FOR ROOF OPENINGS