A06_SOW_and_Specs_for_Vehicle_2__TXBAR_2352_edited_2.pdf

Statement of Work

Location of vehicle: Balcones Canyonlands NWR

24518 E FM 1431

Marble Falls, TX 78654

WARRANTY

The contractor will provide a minimum twelve (12) month warranty on all work. Major components and sub-assemblies shall be warrantied through their respective manufacturers. In the event a defect in installation workmanship is discovered following delivery of a vehicle at its destination, the contractor shall itself, or sub-contract with a company in that geographic area, to make repairs and shall assume financial responsibility for all costs related to the repair.

SCOPE OF WORK

UP- FITTING

The installation of aftermarket equipment is to be in compliance with the manufacturer instructions for the item to be installed.

The vendor will install all emergency vehicle equipment in a consistent standardized manner.

The vendor will ensure every vehicle is identical in that each component included in the upfitting is the same throughout all vehicles, to include the routes in which the wiring is laid throughout the interior of the vehicle. The wiring must include weatherproof protective sheathing in areas which may subject the wire to outside elements, in areas that are crimped, and/or areas that wear may cause failure of the equipment to which it is connected, and potentially damage to the vehicle.

The wiring standard for FWS vehicles must account for all butt connectors and solder point be shrink wrapped at the connection points. When installing equipment and wiring the vehicles, the vendor shall ensure that performance and workmanship will minimize risk of electrical failure, mechanical failure, and/or fire due to changes made by the vendor.

The vendor will leave a basic wiring and fuse box diagram for any installed or upgrades to the

OEM fuse box, in the glove box of the completed vehicle.

The installed equipment must be able to sustain extremes in vibration, climate, and conditions, from extreme cold, snow-covered highways, to extreme hot, dusty wash-boarded gravel roads, to off-road use.

When selecting mounting location for lights or accessories on or in the vehicle, resale consideration should be factored in, with no holes drilled into the exterior of the vehicles body, and minimal holes drilled within the interior.

Ideally, additional lights and/or accessories are to be mounted (holes) in less conspicuous locations or on aftermarket hardware.

All original equipment removed from the vehicle is to be returned with the vehicle at time of delivery.

Specs for TX-BAR 2352 Vehicle #2

Requirements include general upfit, emergency lights and sirens, agency specific striping and graphics.

The vendor location must be within 250 miles of Marble Falls, TX, or pickup and delivery included within the price. The vendor must provide hands on training of the installed equipment. The upfit must fit a customer supplied already purchased 2025 Chevy 2500 HD.

General Upfit Specifications

• Console – To include One (1) faceplate for customer specified radios, One (1) mounting panel for PA control head, One (1) electrical switch panel to operate lighting and equipment installed on the vehicle. The console shall not replace or interfere with the vehicle’s manufacturer installed console or seat assembly.

• Wiring for Radio(s) Installation - The chassis cab interior shall be wired with one (1) wiring bundle for connecting agency mobile radios. The bundle shall terminate in a Deutsch brand connector. The antenna wire shall remain separate from the connector. A pigtail shall be included for connecting the agency radio into the wiring harness. The individual wires shall be labeled (Battery Power, Ground, PA Input, etc.). The pig tail and antenna wire shall be a minimum of 3-feet or as long as required for installation of the radio.

• Antenna Lead and Base - One (1) antenna mount with coaxial cable shall be supplied and installed centered on the chassis cab roof. The components shall consist of a brass ¾-inch New Motorola

(NMO) style Antenna Mount and Double Shielded Coaxial Cable soldiered to the base. The coaxial cable shall terminate in the cab console and have a minimum of four (4) feet of additional cable. The cable shall be routed from the chassis/cab headliner to the console in a concealed manner. All cables shall be labeled as to where they are installed on the roof. A protective rain cap shall be installed on the NMO antenna mount.

• Brush Guard/Winch – The front of the chassis will be equipped with a heavy-duty brush guard. The brush guard shall be designed specifically for the chassis and shall be designed so that it does not affect the chassis manufacturer’s warranty. The brush guard shall have “wings” around the headlights that don’t interfere with the lighting. The entire assembly shall be fully welded, and have smooth rolled edges to give an OEM appearance. All exterior surfaces of the brush guard assembly shall be coated with a minimum 1-2 mm flat black powder coat. This option will include one (1) off-road

LED light bar provided at the front of the vehicle. The light bar shall be mounted on the middle/bottom bar of the front bumper to permit maximum illumination coverage. The winch shall be installed on the brush guard. The winch shall be installed and wired per manufacturer specifications.

The winch shall be equivalent to the WARN EVO 12S with synthetic rope.

Striping and Graphics

• Body General - All stripes are per NFPA standards and ASTM D 4965, “Standard

Specifications for Retro-reflective sheeting for Traffic Control (unless otherwise specified).” Finish of the striping and emblems shall be void of air pockets, and other blemishes, and edges shall be smooth.

• Front - Each vehicle shall have 3.00-inch to 4.00-inch Blue Block Bold reflective Unit ID and

Equipment ID placed on the end of the front bumper on the driver’s side. Each vehicle shall have the word FIRE in 3.00-inch to 4.00-inch Blue Block Bold reflective on the end of the front bumper on the passenger side. Numbers/Letters shall be centered horizontally within a white stripe on the bumper wings and read left to right.

• Rear - Each vehicle shall have 4.00-inch Blue Block Bold italicized reflective numbers set above the safety yellow reflective stripe on the passenger side of the package. In addition to the numbers, each vehicle shall have 4.00-inch Blue Block Bold italicized letters “FIRE” set above the safety yellow reflective stripe, located at the rear driver side of the apparatus body. Numbers shall not be placed in an area that reduces visibility; across door seams or reflectors and lights.

• Top - Each vehicle shall have a 12.00-inch Blue Block Bold reflective numbers centered on the top of the cab of the chassis. Numbers shall be placed to read from the rear of the vehicle and visible from above. Numbers shall not be placed under the engine lighting package or antennas.

• Agency Striping – Per US Fish and Wildlife Service Specifications. Specification diagram included.

MANUFACTURERS’ GUARANTEES AND WARRANTIES

In addition to the required warranties provided in FAR 52.246.20, the following warranties and guarantees shall be provided:

All manufacturer or installer guarantees/warranties obtained by the Contractor for any materials, products, services, or equipment procured for this project shall be obtained for the use and benefit of the Government.

A copy of the manufacturer’s standard warranty shall be enclosed in the package or included with shipping documents, as appropriate, for each warranted item delivered under this SOW, and included in a packet within each vehicle.

If a claim for warranty is requested, the vendor will work to make the repair, provide technical assistance, or send replacement parts in an expedient manner.

Items warranted by the manufacturer’s standard warranty shall be marked or stamped

“Warranted.” If space on the item is not available, the packing slip should state, as a minimum, the following:

• Brief statement that a warranty exists.

• Substance of the warranty.

• Duration of the warranty.

• Person/company to notify if the items are defective.

POINTS OF CONTACT

Contracting Officer’s Technical Representative

Carl Schwope

Fire Management Officer, (or designee)

U.S. Fish and Wildlife Service

Balcones Canyonlands NWR

24518 E FM 1431

Marble Falls, TX 78654

Phone: 512-234-1999

Email: Carl_Schwope@fws.gov mailto:Frank_Montoya@fws.gov

DOI Striping standards for light vehicles

A06 Specs for Vehicle 2_ TXBAR 2352.pdf