98-20250304110231 MADISON.pdf

SPECIFICATIONS AND PROPOSAL SHEET

Madison County Fire Services-Commercial Tanker

UNLESS OTHERWISE NOTED, ALL SPECIFICATION ARE STATED AS THE MINIMUM REQUIREMENT

UNPRICED PROPOSALS DUE 10:00 a.m. – Thursday, April 3, 2025 UNPRICED

PROPOSAL MUST BE SIGNED & SUBMTTED ON COUNTY’S PROPOSAL SHEET

INVITATION TO BID

Madison County Fire Services is seeking sealed proposals for one-(1) or more 3,000 Gallon Extruded Aluminum Tanker Apparatus mounted on a Kenworth T480 450hp or comparable model conventional cab and chassis. Sealed proposals will be received until 10:00 a.m., on Thursday, April 3, 2025 at the Madison Chancery Clerk’s Office, 125 West North Street, Canton, MS 39046. The outside of the sealed envelope must be properly marked and identified by:

"Madison County Fire Services – Commercial Tanker”

Proposals may be submitted by either of the following methods:

1. Sealed proposals will be received until 10:00 a.m., on Thursday, April 3, 2025, at the Madison County Chancery Clerk’s Office, 125 West North Street, Canton, MS 39046.

All sealed proposals submitted to the Chancery Clerk’s Office shall have the bidder’s name and the name of the product or service for which a proposal is being submitted written on the outside face of the envelope. If any envelope is not so marked, said proposal shall not be opened or considered.

2. Electronic proposals will be received until 10:00 a.m., on Thursday, April 3, 2025, as a PDF file via Madison County’s website at http://www.madison-co.com/bids. Each bidder submitting a proposal electronically shall include a signed copy of Madison County’s proposal sheet as part of it PDF proposal submittal.

3. Bid Opening: The sealed proposals will be opened and reviewed by the authorized personnel at the designated time and date specified in the bid documents. Bidders who choose to attend the bid opening in person may do so, but it is not a mandatory requirement for bid consideration.

4. NO EXCEPTIONS: If the phrase "NO EXCEPTIONS" is explicitly noted in this proposal, it shall be strictly adhered to. No deviations or alterations from the specified requirements will be accepted, unless explicitly stated otherwise in this proposal document.

http://www.madison-co.com/bids

5. Exceptions and Alternatives: In the event that exceptions to the stated requirements are deemed necessary, the bidder must clearly indicate any deviations and provide alternative solutions, along with a valid reason for the proposed changes. Failure to do so may result in the disqualification of the bid.

6. Total Exception and Demonstration Units: Bidders are prohibited from taking total exception to the specifications and requirements outlined in this proposal and proposing the use of demonstration units as a substitute. Any proposal that deviates substantially from the specified requirements or proposes the use of demonstration units will be disqualified from consideration.

7. Third-Party Certification: All third-party certifications related to this proposal shall be performed exclusively by Mistras Group LLC. No other certification entities or organizations will be considered or accepted. Compliance with this requirement is mandatory.

8. Testing Standards: All testing performed under this proposal shall strictly adhere to the current editions of both the NFPA 1900 Standard for Fire Apparatus and the NFPA 1910 Standard of Testing of Emergency Vehicles. These standards represent the minimum acceptable criteria for evaluating the performance and safety of the proposed equipment.

9. Delivery: The proposed fire apparatus must be delivered within 180-210 calendar days from the issuance of the purchase order. The bidder shall ensure that all necessary arrangements, manufacturing processes, and logistics are in place to meet this delivery timeframe.

By submitting this sealed proposal, the bidder acknowledges that they have read, understood, and agreed to comply with all the terms, conditions, and requirements outlined above.

The below signed company agrees that if it is awarded the proposal by the Madison County Board of Supervisors for any or all of the products on this Specification and Proposal sheet that it will provide said product(s) in a timely manner at the awarded proposal bid price.

Final bidding for proposals will be held by live electronic reverse auction on Tuesday, April 8, 2025, beginning at 10:00 a.m. CDT, with scheduled ending time of 11:00 a.m. CDT.

Qualified vendors can access the live reverse auction on the link distributed by email to qualified vendors.

Madison County Fire Services and Madison County Board of Supervisors reserves the right to reject any and all bids and accept the bid if it is in the best interest of the Fire Department.

Any questions concerning this proposal specification shall be in writing and must be approved by the Fire Department.

Questions should be directed to:

Minor Norman Fire Coordinator Madison County Fire Services minor.norman@madison-co.com

COMPANY NAME: ____________________________________________________________

ADDRESS: ___________________________________________________________________

TELEPHONE: ___________________________________________________

FAX NUMBER: __________________________________________________

EMAIL: _________________________________________________________

AUTHORIZED REPRESENTATIVES SIGNATURE DATE

PRINTED AUTHORIZED REPRESENTATIVE’S NAME HERE

*PROPOSALS SHEET MUST BE SIGNED AND DATED BY AN AUTHORIZED COMPANY

REPRESENTATIVE

Publish: March 6, 2025 & March 13, 2025 mailto:minor.norman@madison-co.com

APPARATUS DIMENSIONS

• Wheelbase of chassis: 236”

• Cab to axle dimensions: 166.5”

• Overall apparatus length: 33’ 6” MAXIMUM (No Exceptions)

• Overall body length: 210”

• Overall body width: 102”

CERTIFIED WELDERS

Employees classified as welders shall be certified for qualification to perform welding within the scope of the American Welding Society and American Society of Mechanical Engineers welding codes.

All steel welding shall follow American Welding Society requirements for AWS D1.1:2020 Structural Welding Code for welding steel structural assemblies. All aluminum welding shall follow American Welding Society requirements for AWS D1.2/D1.2M:2020 Structural Welding Code for any type of structure made from aluminum structural alloys. All sheet metal welding shall follow the American Welding Society AWS D9.1M/D9.1:2018 Structural Welding code for Arc/Braze requirements of non-structural materials. All pressure pipe welding shall follow American Society of Mechanical Engineers ASME IX/ ASME B31:2022 requirements for the qualification of procedures in welding and brazing, by the ASME Boiler and Pressure Vessel Code and the ASME B31 Code for Pressure Piping. Flux core arc welding to use alloy rods, type 7000, American Welding Society AWS standards A5.20-E70T1.

The manufacturer shall be required to have an American Welding Society-certified welding inspector in the manufacturing facility during procedure qualifications and to verify the compatibility of materials and techniques used to produce welded components that follow compliance with welding codes and have acceptable mechanical properties.

DETERMINATION OF IN_SERVICE WEIGHT

Each Manufacturer is required to submit estimated "in-service" weight analysis required by applicable NFPA standards. This computer weight analysis shall break down all major components of the apparatus; it shall show the impact on percentage-of-load on the front and rear axles, total weight, and weight on each tire set. The analysis shall evenly distribute the NFPA required minimum payload allowance or estimated equipment payload as supplied by the purchaser into the specified compartments. The allowance for hose loads, water and foam fluids, and required NFPA equipment shall be outlined individually in the analysis and placed on the apparatus in its specific intended position.

CENTER -OF-GRAVITY ANALYSIS

The Manufacturers shall submit an engineering report on the estimated the center of gravity calculation as required applicable section NFPA standards. This report shall include tilt angles, the estimated right to left load distribution, and load on each axle, including all specified major components. The tilt and weight calculation system shall be supplied.

DRAWINGS

The Manufacturer shall submit detailed specifications and standard drawings for the apparatus with the bid submission. The Manufacturer shall provide detailed engineered drawings of the body and compartmentation of the apparatus. Additional information as to the materials, design, and performance of the product shall be submitted for evaluation by the purchaser in accompanying specifications.

APPROVAL DRAWINGS

The Manufacturer shall provide complete APPROVAL drawings that exactly reflect the construction specifications. The signed drawing shall become an integral part of the final contract and shall be kept on file for future reference.

PRE-CONSTRUCTION CONFERENCE - FACTORY

An authorized Manufacturer's Sales Representative shall be required to facilitate a pre-construction conference at the manufacturing facility with a factory representative present to finalize all construction details.

FINAL INSPECTION - FACTORY

An authorized Manufacturer's Sales Representative shall be required to facilitate a final inspection conference at the manufacturing facility with a factory representative present to finalize all construction details.

COMMERCIAL CHASSIS

Model

0000480 T480 Series Conventional

0071000 T480 Aero Hood

0080070 CARB Exempt Application Emergency Vehicle Only.

0090161 T480 Tandem Rear

Engine & Equipment

0130215 PX-9 450EV 450@2100 1250@1200, 2024

With Turbo Exhaust Brake (VGT Brake). Emergency Vehicle N09420 C333 0.....Reserve Speed Limit Offset N09380 C334 0.....Maximum Cycle Distance (N202 N09360 C400 252...Reserve Speed Function Reset N09200 C399 120...Standard Maximum Speed Limit N09400 C401 10....Maximum Active Distance (N20 N09220 C402 0.....Expiration Distance (N207) N09540 C395 0.....Expiration Distance (N209) N09260 C121 62....Max Vehicle Speed in Top Gea N09440 C234 NO....Engine Protection Shtdwn N09460 C231 NO....Gear Down Protection N09580 C133 5.....Idle Shtdwn Time N09680 C233 NO....Idle Shtdwn Override N09480 C132 1400..Max PTO Speed N09300 C128 62....Max Cruise Control Speed N09500 C239 NO....Cruise Control Auto Resume N09520 C238 NO....Auto Engine Brake in Cruise N09780 C190 80....High Ambient Temperature Thr N09740 C188 40....Low Ambient Temperature Thre N09760 C189 60....Intermediate Ambient Tempera N09720 C382 YES...Enable Hot Ambient Automatic N09600 C396 YES...Enable Impending Shutdown Wa N09620 C397 60....Timer For Impending Shutdown N09640 C206 35....Engine Load Threshold N09560 C225 NO....Enable Idle Shutdown Park Br

1000046 EPA Emissions Warranty Engine

1000151 PremierSpec

1000243 Gearing Analysis: Performance power before economy results.

1000250 Customer's Typical Operating Spd: 58 MPH

1000525 Registration Year Year of Registration: 2025

1000684 Effective VSL Setting NA

1000858 Engine Idle Shutdown Timer Disabled

1000891 Eff EIST NA Expiration Miles. Use only with MX and Cummins engines

1002060 Air compressor: Cummins 18.7 CFM For Cummins And PACCAR PX engines.

1041399 Air Cleaner: MD Composite Engine Mounted

1093120 Inside/Outside Air Intake for Engine Mounted Air Cleaner

1099300 Air inlet ember separator NFPA compliant for fire applications.

1105231 Fan Hub: Horton On/Off for PX-9 or L9N

1121231 Cooling Module: 2.1M MD - Aero Hood 1000 Square Inches

1247234 EXH: 2021 RH Under DPF/SCR with RH SOC Vertical tailpipe. Not 2.1m high roof sleepers

1290124 Tailpipe: 5 in. single 24 in. 45 degree curved.

1321102 Fuel Filter: PACCAR 2.1M MD for PX-7 or PX-9 Fuel/water separator for 2021 and later engines.

1321205 Run Aid:Fuel Heat *For Fuel Filter

1321305 Start Aid:12V Heat *For Fuel Filter

1500029 Kenworth Fuel Cooler

Required for Cummins engines with a single fuel tank. Required for PACCAR MX-13 engine with a single fuel tank and stationary use: High RPM, low vehicle speed, sustained for longer than 1 hour. Optional for all other applications.

17000149 Retarder: Jacobs for PX-9 and ISL With 3-way switch. Replaces the standard turbo brake for PX-9 engines.

1812451 Alternator: Delco 40SI 320 amp Brushless with battery voltage sense

1821210 Batteries: 3 PACCAR GP31 threaded post (700-730) 2100-2190 CCA dual purpose.

1836106 Mitsubishi 105P55 12V Starter with Cummins and PX

PACCAR 12 volt electrical system. W/ centralized power distribution incorporating plug-in style relays. Circuit protection for serviceability, 12-volt light system w/circuit protection circuits number & color coded. Only for Cummins or PX engines.

1840065 12V Low Voltage Disconnect for Battery Protection

1840066 Cab Power Cutoff SW on Cab Floor

NFPA Compliant - Engine Shut off. Includes gauge.

1900996 Jump start terminals under hood.

1901020 Remote PTO/Throttle, 12-Pin, 500K, Back of Cab OR Back of Sleeper, J1939, Remote Control Provision

Transmission & Clutch

2011614 Transmission: Allison 3000EVS 5-speed, With PTO drive gear. 6th Generation controls. Includes heat exchanger & oil level sensor. Emergency Vehicle Series for vocational applications. Transynd transmission fluid is standard on all Allison 1000, 2000, 3000 & 4000 series transmissions.

2349999 Jackshaft

2406802 Driveline: 3 Dana SPL170XL 2 centerbearing

2409942 One Heavy-Duty One-Piece Aluminum crossmembers

This option upgrades existing crossmembers. The cost does not include the centerbearing and bracket. Crossmember locations will be in accordance with Kenworth engineering standards, using the major components specified on the

DTPO.

2410018 Torque converter included w/Allison Transmission.

2410114 Left hand PTO access, right hand dip stick tube Allison 3000 series only.

2410153 Push Button Shifter Controls, Center Console Mounted for Allison Transmission.

2.1m Medium Duty only.

2410244 J1939 Park Brake Auto Neutral

2429358 Rear transmission support springs for transmission PTO applications are required to ensure that engine flywheel housings are not overloaded when transmission PTO’s are installed.

2429378 Customer installed transmission PTO in the LH Mounted position (8 o’clock) for Allison 3000 & 4000 transmissions.

2460070 Supplemental Allison Oil to Water Trans Cooler

Front Axle & Equipment

2534001 PACCAR FX-20 ST Fr Axle rated @ 18K 4" drop

2621078 Front Brakes: 14,601-22K Bendix ES S-cam 16.5x6 in.

2690025 Splined Rotor for Front Air Disc Brakes for Use with Iron Hubs.

2690039 Integral Knuckle for Air Disc Brake, for use on PACCAR FX Steer Axle

2702018 Front Hubs Iron hub pilot 18,000 lbs. 16.5x6in. or 7in. or air disc brakes. 10

Bolt, 11-1/4 in. bolt circle. Consider Wheelguards (5850002) with aluminum wheels.

2741970 ConMet PreSet Plus Hub package; front axle.

2750001 Hubcap: front vented.

2765001 Front Auto Slack Adjuster.

2769000 Slack Adjusters Included W/ Front Axle or Brakes. Also use with disc brakes.

2865025 Front Springs: Taperleaf 20K W/ Shock Absorbers w/ maintenance-free elastomer spring pin bushings.

2895305 Dual power steering gears: 18/20K.

2899336 Power Steering Cooler:Radiator Mounted Air-to-Oil

2900063 70 mm front suspension spacer block.

2900612 Threaded front spring bushings in place of elastomeric.

Rear Axle & Equipment

3142170 Dual Meritor RT46-164EH Rear Axle rated at 46K. Tandem rear axles. Heavy wall housing

3200563 Rear Axle Ratio - 5.63.

3334004 Dual Rear Brakes 16-1/2x7 in. to 46K; Bendix ES-extended service S-cam.

3392005 Dual Rear Brake Drums: Cast. For use with 16.5X7" or 16.5X8.625" brake.

3407050 Dual Rear Hubs: Aluminum Hub Pilot 46K; 11.25" bolt circle. Requires "R" series outer ends.

3441972 ConMet PreSet Plus Hub Package; Dual Rear Axle.

3465002 Tandem Rear Axle Automatic Slack Adjusters.

For use with drum brakes.

3485207 Spring Brake: 3030 Long Stroke Dual 30 Square inches travel. For drum brakes.

Helps keep brakes in adjustment longer.

3495299 Bend 6S/6M Anti-Lock ATC / ESP

3500057 Interaxle Driveline: 1 Dana SPL170XL

Tandem Rear Axles Only

3500073 Tanker Height between 75 in. and 85 in. from Top of frame rail.

3511420 Driver Controlled Differential Lock (Crosslock) for Meritor Axles 40K to 52K forward rear & rear rear axle. Under Speed Interlock is standard on T680.

3573111 Separate Switch for Dual Axles: differential lock or crosslock.

3742020 Rear suspension: Tandem Hendrickson Primaax EX462

46K. Steel crossmember & gussets. 54 in. axle spacing. 10 in. ride height.

3832098 Track Rods: Heavy Duty for Hendrickson Primaax EX tandem. Replaces standard duty track rods.

3832320 Bolted Rear Suspension Crossmember for PRIMAAX EX single. Replaces medium duty standard.

Tires & Wheels

4010006 Front Tires: Michelin X Works Z 315/80R22.5 20PR

4217402 Rear tires: Michelin XDS2 11R22.5 16PR 41.9 in. diameter, drive. 19.6 in.

SLR.DR. Code is priced per pair of tires.

4900008 Rear Tire Quantity: 8

5045280 Front Wheel: Alcoa 89U64 22.5X9 AL Ultra One High Polish Wheel.

5242338 Rear Wheel: Accuride 43644 22.5X8.25 aluminum hub pilot mount standard polish.

5850040 Wheelguards: All Axles.

5859010 Single Front Axle: 2 wheels Dura-Bright Mirror Polish Dura-Bright outboard surface of aluminum wheels.

5900008 Rear Wheel/Rim Quantity: 8

Frame & Equipment

6054410 Frame Rails: 10-5/8 x 3-1/2 x 5/16 in. Steel to 309 in. to 380 in. Truck frame weight is 2.91 lb.-in. per pair of rails. Section modulus is 14.80 cu.in., RBM is 1,776,000 in-lbs per rail. 120,000 PSI yield. Heat treated. Frame rail availability may be restricted based upon application, axle/suspension capacity, fifth wheel setting, or component/dimensional specifications. The results of the engineering review may result in a change to the requested frame rail. If a change is required Kenworth Application Engineering will advise the dealer of the appropriate material specification for a substitute rail.

6141400 Full Steel Insert: for 10-5/8 in. or 10-3/4 in. Steel 285 in. to 336 in. or 2nd insert for 11-5/8 in. steel frame. Adds 1,149,000 in-lb to main rail RBM. Truck insert weight is 2.05 lb.-in. per pair of rails. Full frame insert length is equal to wheelbase plus rear frame cutoff plus dimension forward of front axle by model.

See databook addendum section 7.2.

6308715 Bumper: Aerodynamic Chrome Requires a bumper setting code.

6319040 40 in. Bumper setting. Requires a bumper code.

6321010 Front tow loops: Two

6390097 DXF frame layout to dealer prior to build date. Information only, no changes. This provides a frame layout in a .DXF format data file suitable for use w/ many CAD programs.

6391202 Custom Frame Layout: two chassis

6391205 Custom Frame Layout: 5-9 Chassis

CFL F/T: UNDER DRIVERS DOOR SEE 372068

6400633 Battery Box: Temporary Across the Rails. Includes maximum cable length available.

6409908 Battery box location: BOC across the rails.

6451126 DPF/SCR box polished end plates and polished cover.

6490139 Heavy-duty one-pc aluminum intermediate/fill-in crossmember.

6490433 Heavy-duty 5-piece rear cab support, hucked assembly. Huck fastened to frame.

6721102 Rear Mudflap Arms: Betts B-25 Standard-Duty, straight. Includes B1732 mounting brackets as standard.

6722000 Rear Mudflap Shields: White Plastic Antisail W/ Kenworth logo.

6742009 Square End-of-Frame W/O Crossmember; Non-Towing.

Fuel Tanks & Equip

7140050 50 US gallon D-Shape rectangular aluminum under fuel tank, replace. With non-slip step.

7722170 Small DEF tank, 5.5 gallons.

7839006 Polished fuel tank steps.

7840015 Polish only one aluminum tank.

7840038 Polished cover for 1 DEF tank any size.

7889061 Polished stainless steel tank straps for 1 tank.

7889208 DEF to fuel fill ratio between 1.25:1 and 2:1.

7889245 Anti-siphon device in fuel tank filler neck. For any number of fuel tanks.

7889606 DEF tank location is LH under cab.

7920050 Location: 50 gal fuel tank LH under cab

Cab & Equipment

8024311 Cab: Stamped aluminum with curved windshield LED markers. Requires seperate roof code.

8090155 Hood: Med Aero w/ Chrome Crown

8108003 Ember Filter For Cabin Air.

Used to keep embers out of the HVAC filter element. Cannot be used with code 8108002.

8108011 Cab HVAC - Day Cab and 40in Sleeper System With Defrost, A/C, and 48,000

BTU/hr Heater. Includes automatic temperature control with one touch defrost operation and dash mounted cab temperature and solar intensity sensors. Pleated fresh air filter and cabin recirculation air filter standard. The Kenworth HVAC system is designed to provide optimal heating and cooling in all operating environments without need for additional insulation. Cab HVAC without sleeper heater AC is available with 40in sleeper.

8201013 Steering wheel: 18 in. 4-spoke.

8201200 Adjustable telescoping tilt steering column.

8203044 Four position ignition switch, keyless.

Available for fire truck service & EMT/emergency service only.

8205135 Information for customer-installed PTO Muncie 10-bolt.

8205177 Dash Switch: 1st Allison-mntd PTO.

Electric switch and wiring are factory-installed to control the 1st Allison Trans mounted PTO.

8208494 One Spare Switch: Wired to Power.

8220106 Gauge: Dash mounted air filter restriction gauge.

8222712 Gauge: Fuel filter restriction gauge.

8282024 Main Instrument Package: 7" Digital Display Cluster. Includes Physical (Analog):

Speedometer, Tachometer, Oil Pressure, and Coolant Temp; and Digital: Fuel Level #1, DEF Level, DPF Filter Status, Fuel Economy, Volts Telltale, OAT and Primary Air Pressure, Secondary Air Pressure, and Air Application for air brake trucks.

8330591 Interior Trim Package: 2.1M MD Gray Foam Backing/Cloth Headliner W/Gray Sunvisor & Seat Color Three Underdash Center Console Cupholders (Two If Allison Transmission Is Selected).

8410361 Driver Seat: NFPA Compliant KW Air Seat HB Vinyl No Armrests, w/ Susp

Bellows Cover and Isolator.

8460361 Rider Seat: NFPA Compliant KW Air Seat HB Vinyl No Armrests, w/ Susp

Bellows Cover, Isolator and Occupancy Sensor.

8489912 NFPA Compliance Kit: 2.1m Includes seat occupancy sensors. Seat belt switches, VDR & seat sensor harness, reflective labels, and a second copy of operators manual.

8496575 Driver & Rider Seat Belts: Red, NFPA, Replaces Standard Seat Belts. (Available for NFPA RD Bench)

8601432 Kenworth Radio DEA710 AM/FM/WB/USB, Bluetooth

8698965 Speaker Package For Cab: (2) Speakers B-Pillar

8700091 Ashtray insert: W/cigar lighter located in center console. Deletes 1 12V outlet & 1 cupholder.

8700161 Footwell Light: Red Lens & Switch

8700196 Turn Signal: Self-Cancelling

8700283 LH and RH Trip Ledge Rain Deflectors

8700501 Metal Int Door Panel Kick Plates

8700663 Kenworth TruckTech+:

This system provides the World's Best reporting of engine and aftertreatment fault codes, as well as enhanced support for the truck owner through rapid communication of fault severity and recommended actions. This is standard on all Kenworth models with a PACCAR MX engine, Cummins X15 engine, PX engine or Natural Gas engine.

8800402 Dual Cab Interior Grabhandles: A Pillar Mounted Dash Wrap and B Pillar

Mounted Grabhandles

8832113 Kenworth Daylite Door with standard LH/RH electric door locks and LH/RH electric window controls.

8841411 Single air horn under cab.

8850139 Look-Down, Pass. Door, Black 11x6

8850841 Mirror Shell: Dual Aero Chrome

8860852 Mirror: Dual KW Aero Rear View Motor, heated with Integral CX.

8879922 Solid rear wall. Deletes rear cab window.

8890101 One-piece bonded-in windshield with curved glass. Standard.

8890874 Kenworth Cab Air Suspension.

8891009 Thermal/Sound Insulation Package

8891011 Roof: Raised Profile, Stamped Aluminum w/ Additional Head Room & Interior

Overhead Storage

Lights & Instruments

9010813 Headlamps: Single Halogen Complex Reflector w/ Turn Indicator, Reflector and w/o DRL. Fender Mtd.

9010951 Daytime Running Lights Located in Bumper.

Driven by Chassis Height.

9022137 Marker Lights: Five, rectangular, LED

9030052 LED Stop,Turn,Tail: With Two LED Backup Lights and With An LED License

Plate.

9090027 Headlamps to turn on when wipers are active.

9090052 Brake Lights on when Engine Brake Active.

Can only be selected when chassis also has engine brake. Cannot be used with options to delete engine brake.

9090115 Reflectors: Two Midframe

9090180 Backup alarm: Tail light bracket mounted variable self-adjusting 82-102 DBA.

9090312 Body Builder Lighting Harness Coiled End Of Frame For Additional Customer Installed Exterior Lighting. Harness Includes Circuits for Additional Customer Installed Tail Lamps, Turn Lamps, Stop Lamps, and Marker Lamps.

9090316 Junction Box: End of Frame

9090849 Polyswitches replacing fuses. Switch will automatically reset after removal of excess load.

Air Equipment

9101218 Air Dryer: Bendix AD-HF Puraguard Heated

9102009 Moisture ejection valve: Midland automatic Use with AD-IS or AD-HF.

9140020 Nylon air tubing in frame & cab, excluding hoses subject to excessive heat or flexing.

9140092 Schrader valve to charge air system.

Extended Warranty

9200008 Base Warranty - PACCAR PX-9 Engine

24 months / 250,000 miles / 402,336 km / 6250 hours.

9200113 Severe Service Medium-Duty Warranty: 12 months/ 50,000 miles & km

9212661 TruckTech+ RD - 5YR Sub PACCAR PX Engines

9220001 Base Warranty: Emissions

5YR/100K MI - EPA Engine

Miscellaneous

9409852 GHG Secondary Manufacturer: Does Not Apply

9490003 Additional lead time required for off highway & /or specialty component truck.

9490206 Warning Triangle Reflector Kit: Shipped Loose.

Kit consists of 3 triangles in plastic carrying case. Not floor mounted.

9490404 One 5 lb. Dry Chemical Type Fire Extinguisher mounted outboard of driver seat.

Class ABC.

9491659 VMUX Architecture

Paint

9700000 Paint color number(s).

N9702 A - Z9990 UNPUBLISHED PAINT

N9720 FRAME N0001 BLACK

9943004 Bumper Unpainted

9943050 Day Cab Standard Paint

9944820 1 - Color Paint - Day Cab

Color will be White if no other color is specified.

9960003 Non-standard paint color.

Narr 910068EY Blaze Red

9965510 Base coat/clear coat.

The Kenworth Color Selector contains additional instructions, as well as information on Kenworth paint guidelines and surface finish applications. Kenworth is standard with Dupont Imron Elite paint.

FRONT BUMPER STEEL CHANNEL STYLE

The chassis front bumper shall be fabricated of steel channel style and be twelve (12)-inches high.

Note: Painted job color red.

FRONT BUMPER NOTCH

The chassis front bumper shall be notched for mounting a Q2 siren.

Note: Driver's side of front bumper to be notched for fully recessed Q2B

FRONT BUMPER EXTENSION

The chassis front bumper shall be extended eighteen(18)-inches.

Note: The bumper shall be extended beyond the front face of the cab and long enough for a single center hose storage well designed to accommodate 100' of pre-connected 1-3/4" DJ hose.

The KW tow eyes shall be extended with the front bumper.

FRONT BUMPER GRAVELSHIELD

The extended front bumper shall be overlaid with an aluminum diamond plate gravelshield.

FRONT BUMPER COMPARTMENT-CENTER

There shall be a front bumper compartment supplied on the front bumper extension located in the center.

RESTRAINING STRAPS

Two-(2) restraining straps shall be installed on the front bumper compartment.

MECHANICAL SIREN

An electro-mechanical Federal Signal Q2B siren shall be recessed into the front bumper on the Driver's side. A siren brake shall be provided on the center console.

SIREN ACTIVATION

The mechanical siren shall be active in response mode only.

SIREN ACTIVATION

The mechanical siren shall be activated by a foot switch mounted in the front section of the cab floor for use by the Driver.

The foot switch shall be labeled "Q2B SIREN".

SIREN SWITCH

A siren switch shall be supplied on the Officer's side of the center console.

AIR HORNS

-The air horns shall be mounted on the fender, one(1) on each side.

AIR HORN ACTIVATION

The air horn activation shall be controlled by a lanyard cable mounted between the Driver and Officer.

SIREN SPEAKER

A 100-watt siren speaker shall be supplied.

-The siren speaker shall be recessed mounted on the Passenger's side front bumper.

WHEEL TRIM

There shall be chrome plated hub and lug nut covers installed on the front and rear wheels of the chassis. Lincoln hat type hub covers shall be supplied for the rear wheels.

TIRE PRESSURE MONITORING SYSTEM

All tires shall be equipped with an LED Alert tire pressure monitoring system.

AIR AUTO EJECT

There shall be a Kussmaul model#091-28 or equivalent comparable model air auto eject provided on the air inlet.

Location: Driver's Side Front of the Pump Module

- the Air Eject shall be provided with a black weatherproof cover.

BATTERY RELOCATION

The chassis batteries shall be relocated to the driver’s side front compartment. An aluminum treadplate cover with removable top. The edge of the batter cover shall be extended up 2" with turtle tile provided on top of the batter cover.

BATTERY CHARGER

A Blue Sea/Pro Mariner 40-amp battery charger shall be installed.

SHORELINE AUTO-EJECT

A Blue Sea 20amp Sure Eject, model#7851 or equivalent comparable model, with weatherproof cover shall be supplied.

-The receptacle shall be located on the left side pump panel.

COVER

A yellow Blue Sea Sure Eject cover model#7820 or equivalent comparable model shall be supplied.

PLATE – SHORE POWER INLET

A plate shall be provided adjacent to the shore power inlet clearly stating the line voltage/amperage input.

MASTER BATTERY DISCONNECT

A master battery disconnect switch shall be provided.

Location: Outboard of driver’s seat on cab floor.

CENTER CONSOLE (CUSTOM)

A center cab console with binder storage shall be supplied and installed on the cab floor.

Console Shall House the Following:

(2) USB-A/C Chargers

(1) 12-Volt Power Outlet Master Warning/Rocker Switch Panel Battery On/Ignition On Indicator Lights Low Voltage Alarm/Light Door Ajar Light/Alarm Customer Suppled Radio Pump Shift Electronic Siren

INTERIOR DOOR TRIM

Reflective material shall be added to the lower portion of the inside of the cab doors.

BATTERY “ON” INDICATOR LIGHT

A battery “On” indicator light shall be provided on the cab console.

IGNITION “ON” INDICATOR LIGHT

An ignition “On” indicator light shall be provided on the cab console.

LOAD MANAGER

A load manager with integrated automatic high idle shall be provided within the cab chassis.

VEHICLE DATA RECORDER

A vehicle data recorder with seat belt warning display shall be provided within the cab chassis.

FUSE BLOCK

A 12V twelve (12) place fuse block shall be installed in the chassis cab.

Note: (6) Hot all-the-time / (6) Battery Switched

Location: Within Center Console

DUAL USB CHARGING PORT

Two-(2) Kussmaul model#091-264 combination 12-volt USB A/C charging port or equivalent comparable model shall be installed in the chassis cab.

Note: Battery Switched

Location: Center Console

RADIO INSTALLATION PROVISION

A provision shall be provided within the center console for the installation of a customer supplied radio. Madison County Fire Services shall specify the radio make/model and head type to the awarded bidder.

RADIO ANTENA MOUNT WIRING

One(1) MNO style mount shall be installed.

Termination: Center Console

12VDC POWER CIRCUIT

A 12VDC power 30amp battery "hot" protected 30 amp switched circuit and ground shall be installed on the center console.

This circuit shall be supplied for two-way radio and/or accessory wiring.

12 VOLT POWER

A 12-volt outlet shall be supplied in the location specified. The outlet shall be activated by a switch and circuit protected capable of carrying up to a 15 amp battery direct load.

Note: Battery Switched Location: Center Console

120 VAC SHORE POWER OUTLET

A 120 VAC 4 outlet box shall be located inside compartment R1 and shall be powered by the Shore Power connection.

ELECTRONIC SIREN

An electronic Whelen model #295SLSA1 siren shall be supplied.

Location: Center Console

BACK UP ALARM

A NFPA compliant backup alarm shall be supplied. It shall activate automatically when placed in reverse.

"DOOR OPEN" WARNING LIGHT

A "door open" warning light shall be supplied.

ENGINE MAINTENANCE LIGHTS

One-(1) LED engine maintenance lights shall be supplied.

ADDITIONAL LED DOME LIGHTS

One-(1) additional LED Red/Clear dome light(s) shall be supplied.

CAB GROUND LIGHTING

One (1) LED light shall be mounted beneath each cab door.

Note: Activated by Park Brake. NFPA requires a switch to be provided in the cab, however manufacturer to wire switch to default "ON".

BACK UP CAMERA/MONITORING SYSTEM

A Fire Research model #TRUSIGHT BCA111-A00 backup camera with color Monitor shall be supplied and installed in the apparatus.

Locations:

Monitor - Center Overhead (In Place of Rearview Mirror) Camera - Under the Intermediate Rear Step

SAFETY SIGN GENERAL REQUIREMENTS

A Sign, label, or decal affixed to a product that provides essential information concerning a potential hazard, the degree or level of hazard seriousness, the probable consequence of involvement with the hazard, and how the hazard can be avoided shall be supplied as follows:

The safety signs must be visible to the user near the potential hazard. The safety signs include warnings for:

• Battery explosion.

• Rotating shafts.

• Hot surfaces.

• Hot exhaust.

• Spinning fan.

• Seats without belts not occupied.

• Air conditioning refrigerant.

• Cab equipment mounting.

• Fire service tire rating.

• Electronic stability control.

• Cab seating.

• Helmet worn in cab.

• Vehicle backing.

• Intake and discharge cap pressure.

• Hose restraint required.

• Access step method.

• Riding on exterior.

• Trained personnel only.

• No-step.

• Siren noise.

SAFETY SIGN 'APPARATUS MOVEMENT'

A safety WARNING sign stating: "NO RIDING ON REAR OF APPARATUS" shall be installed on rear of the apparatus.

DATA PLATE 'FLUID CAPACITY'

A data plaque shall be supplied and installed on the inside of driver's door or where practical and easily visible. The data plaque shall contain the required information based on the applicable components for the apparatus, applicable to the applicable NFPA standards:

• Engine oil.

• Engine coolant.

• Chassis transmission fluid.

• Drive axle lubricant.

• Power steering fluid.

• Major components and/or other component lubricates.

• Other NFPA applicable fluid levels or data as required.

• Paint manufacturer, type, and color number.

• GVWR, axle ratings, and equipment load capacity.

DATA PLATE "DIMENSION''

The cab dash area shall have an apparatus dimension label installed. The label shall be highly visible, indicating the overall height, length, width and weight of the vehicle.

PUMP MODULE

The pump shall be manufactured by Hale Products and include the following attributes:

- the pump shall be a Hale Q-series pump

- the pump shall be side-mount operated

- the pump and plumbing shall be enclosed a in tubular aluminum allow module

- enclosed within the tubular aluminum alloy module shall be a Hale QMax-XS pump rated at

1,500 GPM.

PUMP OPTIONS

The following pump options shall be included:

-the pump gear ratio shall be set to 2.28 (-23) -A mechanical seal shall be supplied on the inboard side of the pump. The mechanical seal shall be two 2-inches in diameter and shall be spring-loaded, self adjusting and maintenance-free.

-the pump gearbox shall be provided with 1710 series half-round yokes -the gearbox shall be provided with an air interlock module with VPS

ADDITIONAL OPTIONS

The following additional options shall be provided with the pump module:

- three-(3) pump anode(s) shall be installed in the pumping system to prevent damage from galvanic corrosion within the pump system.

- a Hale TRV-120-L thermal protection device with light or equivalent comparable model shall be installed on the apparatus pump

- an intake relief valve, adjustable from 75-250 PSI, shall be provided. The relief valve shall terminate below the pump with 2.5" male national standard thread.

- the pump module shall be equipped with the Class1 TPG+ governor system. The TPG+ is a J1939 CAN based pressure governing system that consists of a TPG+ display, throttle, pressure transducers and associated wiring.

- a Class 1 model #ITL-40M tank level gauge supplied.

- the module width shall be 76" panel to panel

- the module length shall be 34" front to back

- aluminum diamond plate running boards shall be provided on both the left and right side of the pump module. the running board shall have a width of 99" side to side

- there shall be no hose tray provided on the left side running board

- there shall be no hose tray provided on the right side running board

- the pump panels shall be constructed of 14 gauge brushed stainless steel

- individual line pressure gauge shall be Class 1 2-1/2" white face, reading from 0-400 PSI

- the Master Intake gauge shall be a Class 1 4-1/2" white face, reading from -30-0-400 PSI

- the Master Discharge gauge shall be a Class 1 4-1/2" white face, reading from 0-400 PSI

- all manual drains shall be 3/4" Lift -Up style.

- a 4-light remote tank level driver shall be provided for the installation of additional tank level gauges

- a custom cut-out shall be provided for the installation of a Blue Sea Sure Eject

PLUMBING

All intake and discharge plumbing related components and manifolds shall be fabricated with a minimum of 3-inch, or greater as required by design, schedule 10 stainless steel pipe or high pressure flexible piping with stainless steel couplings. The following intakes and discharges shall be provided:

- Discharge #1: 2-1/2" Left Panel Front, Swing Controlled

- Discharge #2: 2-1/2" Left Panel Rear, Swing Controlled

- Discharge #3: 2-1/2" Right Panel Front, Push-Pull Controlled

- Discharge #4: 3" Right Panel Rear, Electronically Controlled via Akron 9327 Valve Controller

- Front Bumper Discharge: 2-1/2" Valve w/ Push Pull Controlled

- Booster Reel Provision: Capped on Valve Flange on Bottom of Manifold

- Jump Line: 2.0" Valve w/ Push Pull Control

- Deck Gun: 3.0" Valve w/ Push Pull Control

- Tank Fill: 2.5" Valve w/ Push Pull Control

- Tank-to-Pump: 4.0" Valve Electronically Controlled via Akron 9333 Valve Controller

- Left Side Auxiliary Intake: 2.5" Valve w/ Swift Handle

- Right Side Auxiliary Intake: 2.5" Valve w/ Swift Handle

- Crosslay #1: 2.0" valve w/ Push Pull Control

- Crosslay #2: 2.0" valve w/ Push Pull Control

INSPECTION, MAINTENANCE AND TESTING

The fire apparatus shall be properly tested, inspected, and serviced according to the Manufacturer’s and NFPA’s specifications. Listed below are minimum guidelines recommended by the Mississippi State Rating Bureau (MSRB) concerning the life span of a fire apparatus.

A three (3) hour certification test shall be performed consisting of the following:

• At least two (2) hours of pumping at 100% of rated capacity at 150 psi net pump pressure.

• At least thirty (30) minutes of pumping at 70% of rated capacity at 200 psi net pump pressure.

• At least thirty (30) minutes of pumping at 50% of rated capacity at 250 psi net pump pressure.

• An overload test of pump rated capacity at 165 psi net pump pressure for at least five (5) minutes.

This test shall be performed by qualified persons, a third party testing company, or the manufacturer.

MANUAL AIR PRIMER SYSTEM

The priming system shall be a model #31.001.2 (1250+ GPM) Trident Emergency Products manual air prime system.

CROSSLAY COVER

The crosslay cover shall be manufactured of Hypalon material and include end flaps on each side.

CROSSLAY END FLAPS

The crosslay end flaps shall be manufactured of Hypalon material and be fastened with Bungee cords.

- The crosslay cover/end flaps shall be Black in color.

HOSE TRAYS

There shall be two (2) hose trays installed in the running boards, one(1) each side.

HOSE TRAY MOUNTING

The hose tray shall be mounted as a floating drop-in style with 45 degree bottom corners.

AIR HORN SWITCH

The air horn activation switch shall be mounted at the pump panel area.

SWITCH

Four(4) additional 12-volt rocker switch shall be supplied on the pump panel.

Note: FRONT SCENE, RIGHT SCENE, LEFT SCENE, HOSEBED LIGHT

AIR PUMP SHIFT

The pump shift shall be air operated to shift from road to pump and back. The pump shift switch shall be mounted in the cab and labeled as "AIR PUMP SHIFT" with instructions permanently inscribed on the pump shift switch plate.

The pump shift control assembly shall incorporate indicator lights showing the position of the pump when the control is moved to "Pump" position and when both the pump shift has been completed and the chassis automatic transmission is engaged.

An additional indicator light shall be supplied adjacent to the throttle control at the pump operator's panel to indicate a completion of the pump shift.

FRONT BUMPER DISCHARGE

A front bumper discharge outlet with swivel shall be supplied through the treadplate on the Passenger's side of the front bumper apron.

A 2-1/2-inch discharge valve with push/pull control shall be supplied on the front bumper of the apparatus.

A Trident model # 01.006.0 chrome cap w/ chain or equivalent comparable model shall be provided on the front bumper discharge.

FRONT BUMPER DISCHARGE

A front bumper discharge outlet shall be supplied in the center of the hose well compartment.

A 2-inch discharge valve with push/pull control shall be supplied on the front bumper of the apparatus.

BOOSTER REEL

The Booster reel shall be located at the rear of the apparatus, below the dump chute. Captive roller shall be provided under the dump chute. The booster reel rewind button shall be located adjacent to the opening at the rear of the apparatus.

BOOSTER HOSE

One (1) one hundred-foot section of 1-inch booster reel hose shall be supplied on the booster reel.

MONITOR

One (1) Akron Apollo model#3433 portable monitor with ground base or equivalent comparable model shall be supplied with the apparatus.

NOZZLE

There shall be an Akron Akronmatic nozzle model#5160 or equivalent comparable model supplied with the apparatus.

FOAM EDUCTOR

An Akron model #3126 125GPm inline foam eductor or equivalent comparable model shall be provided and plumbed to an integral foam tank.

Note: Plumbed to 1-1/2" Front Bumper Discharge

FOAM TANK

A 30 gallon polypropylene tank shall be supplied internal to the booster tank. The fill tower shall include a latch, vent and cover.

There will be a label on the tank indicating: “WARNING: CLASS A FOAM TANK FILL, DO

NOT MIX BRANDS OR TYPES OF FOAM"

FOAM CONCENTRATE PLATE

A plate indicating the hazards associated with foam concentrate shall be supplied on the apparatus where applicable.

WATER TANK

The polypropylene tank shall be 3000 gallons in capacity.

SPECIAL TANK CONFIGURATION

The polypropylene tank shall be designed in an "L" shaped configuration.

TANK VENT

The water tank shall have a 6-inch poly type vent.

TANK LEVEL LIGHTS

There shall be three-(3) Whelen model PSTANK2 water tank level lights or equivalent comparable model indicating the water level in the booster tank in 1/4 increments supplied with black bezels. The tank level lights shall utilize a pressure transducer and CLASS 1 driver to provide an accurate reading of the water tank level.

Locations: One-(1) per side on the upper front corners of the body, one-(1) on the driver's side rear of the body

Activation: Park Brake

DIRECT TANK FILL

There shall be a rear direct tank fill installed on the right rear of the apparatus. The tank fill shall include a 3" valve w/swing control.

TANK FILL ADAPTER(S)

A Trident Emergency Products model # 01.032.5 3” FNPT x 3” FNHT chrome adapter w/ strainer or equivalent comparable model shall be provided for the direct tank fill.

A Trident Emergency Products model # 01.054.20 3” FNHT x 2-1/2” MNST chrome 30-degree elbow or equivalent comparable model shall be provided.

A Trident Emergency Products model # 01.007.0 2-1/2” chrome plug with chain or equivalent comparable model shall be provided.

DIRECT TANK FILL

There shall be a rear direct tank fill installed on the left rear of the apparatus. The tank fill shall include a 3" valve w/swing control.

TANK FILL ADAPTER(S)

A Trident Emergency Products model # 01.032.5 3” FNPT x 3” FNHT chrome adapter w/ strainer or equivalent comparable model shall be provided for the direct tank fill.

A Trident Emergency Products model # 01.054.20 3” FNHT x 2-1/2” MNST chrome 30-degree elbow or equivalent comparable model. shall be provided.

A Trident Emergency Products model # 01.007.0 2-1/2” chrome plug with chain or equivalent comparable model shall be provided.

10" DUMP VALVE

A 10-inch dump valve with manual control shall be installed on the rear of the apparatus.

DUMP CHUTE EXTENSION TELESCOPING

A 36-inch manual telescoping dump chute extension shall be installed.

BODY DESIGN AND CONSTRUCTION

The apparatus body shall be of all aluminum construction. The body shall be fabricated and assembled on a body "fixture" to assure proper fit, form, and finish standardization. The apparatus body shall be constructed of .1875" thick Type #5052-H32 alloy aluminum sheet (no exceptions). The body shall be designed and engineered specifically for emergency apparatus and shall be built to meet the duty cycle for fire and rescue services.

The apparatus body shall be welded construction for maximum strength and integrity for the entire life of the apparatus. The sub-body structural aluminum extrusions shall be integrated with the exterior body sheet metal and for a reinforced type body construction. The structural extrusions shall be Type #6061 and heat tempered to T-6 hardness. All compartment seams shall be sealed.

A body using stamped and welded steel or aluminum sheet metal designed for commercial purposes shall not be acceptable.

SUBFRAME

The body subframe supports and cross-member extrusions consist of 6061T6 aluminum alloy extrusions.

These cross-members span the entire width of the body providing essential support for compartment framing. Each cross member is securely welded to a 3/4" (.750") x 3" solid aluminum 6061T6 alloy frame rail extrusion.

To prevent direct contact between the aluminum subframe and the chassis steel frame rails, the frame rail extrusion is mounted over a 1/2" (.5") reinforced rubber cushions. This isolation ensures longevity and minimizes wear.

The connection between the apparatus body structure and the chassis frame rails is achieved using a minimum of six (6) 5/8" (.625") cross-member OD steel U-bolts. Additionally, each main body support cross member features gussets above and below, constructed from 2.0" x 4.0" 6063T6 aluminum alloy extrusion with a .190" wall thickness.

BODY WIDTH

The overall width of the apparatus body shall be approximately 102-inches wide.

WHEEL WELL PANELS

The body panel in the wheel well area on each side shall be aluminum and finish painted.

FENDERETTES

The fenderettes shall be of polished stainless steel and installed on body rear wheel well openings, two-(2) each side.

HOSE BED WIDTH

The Hose Bed shall be approximately 73 1/2-inches wide.

BODY COMPARTMENTATION

The following compartments shall be supplied on the apparatus:

COMPARTMENT L1

There shall be one-(1) rescue style compartment installed ahead of the rear axle on the driver's side. The compartments shall have interior dimensions of approximately 64" Wide x 74-1/4" high x 12" Deep in the Upper Section and 28" Deep in the Lower Section.

ROLL-UP DOOR

Compartment L1 shall be equipped with a roll-up door shall be manufactured by AMDOR® brand or equivalent comparable model. The compartment usable door opening shall be approximately 62" Wide x 64-7/8" High.

PULL DOWN STRAP

The compartment door shall be equipped with a pull-down assist strap.

COMPARTMENT LIGHTING

Two-(2) LED strip lights shall be installed in each side of each compartment.

WALL MOUNTED TOOL BOARD/ALUMINUM

An aluminum tool board shall be installed on the back wall of the compartment as specified. The tool board shall be mounted directly to Unistrut material attached to the back wall.

Location: Upper section back wall of the compartment.

UPPER FIXED SHELVING

The upper area of the compartment specified shall have a fixed shelf that is 12 to 15 inches deep.

Location: Compartment Depth Break

FIXED VERTICAL DIVIDER(S)

A fixed vertical compartment divider shall be installed as specified.

Note: A divider shall be installed immediately to the right of the battery storage enclosure in the lower section of the L1 compartment.

COMPARTMENT UNISTRUT

The L1 compartments will have Unistrut mounted vertically in the lower section for installing adjustable shelves and/or roll-out trays.

Note: Vertically mounted on the right side of the vertical divider and the right side compartment wall of the lower section of the compartment for the installation of an adjustable roll-out tray

ROLL-OUT TRAY(S)

One-(1) adjustable mounted tray shall be full width approximately 24-28-inches deep and secured to a "heavy duty" slide assembly. Unistrut brackets shall be supplied for adjustment.

The tray shall have a 500# capacity and 75% extension.

Note: Lower portion of the L1 compartment, to the right of the vertical divider.

One-(1) floor mounted tray shall be full width approximately 24-28-inches deep and secured to a "heavy duty" slide assembly.

The tray shall have a 500# capacity and 75% extension.

Location: Compartment floor, to the right of the vertical divider.

COMPARTMENT L2

There shall be one-(1) rescue style compartment installed above the forward tandem axle on the driver's side. The compartments shall have interior dimensions of approximately 51" Wide x 41" high x 12" Deep.

ROLL-UP DOOR

Compartment L2 shall be equipped with a roll-up door shall be manufactured by AMDOR® brand or equivalent comparable model. The compartment usable door opening shall be approximately 49" Wide x 31-5/8" High.

PULL DOWN STRAP

The compartment door shall be equipped with a pull-down assist strap.

COMPARTMENT LIGHTING

Two-(2) LED strip lights shall be installed in each side of each compartment.

SCBA BRACKET

Two-(2) Zico model #UN-6-30-2-SF SCBA bracket shall be mounted in the compartment as specified below:

Location: Back wall of the compartment

LIGHT(S)

Two-(2) hand held Streamlight Vulcan LED rechargeable lantern(s) model#44451 with quick release shoulder strap and charging base shall be supplied on the apparatus.

Location: Back wall of the compartment, stacked vertically between the Air Pack Brackets

COMPARTMENT L3

There shall be one-(1) rescue style compartment installed above the rear tandem axle on the driver's side. The compartments shall have interior dimensions of approximately 51" Wide x 41" high x 12" Deep.

ROLL-UP DOOR

Compartment L3 shall be equipped with a roll-up door shall be manufactured by AMDOR® brand or equivalent comparable model.