Statement_of_Work.pdf

Statement of Work Firing Range Services – Dallas, TX

The Transportation Security Administration (TSA) requires the use of an established/existing shooting range within a fifteen (15) mile radius of Dallas-Fort Worth Airport (DFW).

Health and Safety Requirements The range shall comply with applicable, local, state and federal regulations and/or laws, including but not limited to, lead exposure.

If an award is made and range standards are not in accordance with regulations and/or laws, the government has the unilateral right to terminate contract at any time via written signed modification.

The following are applicable:

Lead:

• 29 Code of Federal Regulations (CFR) 1910.1000, Air contaminants http://www.gpo.gov/fdsys/pkg/CFR-2014-title29-vol6/pdf/CFR-2014-title29-vol6-sec1910-1000.pdf

• 29 CFR 1910.1025

http://www.access.gpo.gov/nara/cfr/waisidx_10/29cfr1910a_10.html

• Environmental Protection Agency (EPA): Best Management Practices for Lead at Outdoor Shooting Ranges.

Signs and tags:

Section 1910.145 https://www.osha.gov/Reduction_Act/TAGS-SUP.html

Range Requirements The range shall provide a minimum of twelve (12) simultaneous firing points.

The range may be either outdoor or indoor but shall meet the following criteria:

- If outdoor, the range shall be covered or available for all weather use and have proper drainage controls as well as a safe usable all weather surface during rainy conditions, (i.e.

pea gravel, blacktop, concrete).

- If indoor, the range shall possess a ventilation system that conforms to OSHA standards

Whether outdoor or indoor the range must meet the following criteria:

• Must allow for target placement a minimum distance of 1.5 feet from the firing line, and a maximum distance of 75 feet from the firing line.

• Must have distinct firing line indicators (i.e. concrete or blacktop sidewalks for outdoor, firing line http://www.access.gpo.gov/nara/cfr/waisidx_10/29cfr1910a_10.html for indoor).

• All covering supports, barricades or barricade holders on the range shall be constructed of a material that does not deflect/ricochet rounds that inadvertently strike it (Example: wood).

• Must possess or provide target base stands that are compatible with 1"x2" fir strips to hold fixed targets.

• Range rules cannot disallow students from drawing and firing from the holster or students turning and then drawing and firing from the holster.

• Range rules cannot disallow students from multiple and rapid-fire drills.

• Range rules cannot disallow a student from firing and moving in front of the firing points with an instructor present (i.e. tactical movement and shooting drills).

In addition to the range requirements above, the facility must have the following within close proximity (walking distance) to the firing range.

• Firearms cleaning area

• 240 square feet of secure storage that can be provided on-site for safeguarding of targets, ammunition, and other training devices and equipment

• Parking available on site for a minimum of 24 vehicles at one time

• Equipped with separate male and female washroom/restroom facilities

• It is desirable, but not required, to have a classroom or break room to accommodate a minimum of 24 students

• Firing range area in use by the Government shall be closed or limited from view form the public during the corresponding hours of use

A bullet trap shall exist on the range. The range owner will be responsible for lead recovery at the range.

Scope:

The estimated number of rounds fired per month is 192,000.

TSA will provide all ammunition, targets and firearms instructors.

TSA estimates that it will require 768 hours of range time per year. Additional hours may be necessary for a variety of reasons (e.g. hiring surges, changes in training requirements, etc.). Any additional hours are inherently considered to be within the scope of the contract, as the contract is intended to provide for all firearms training needs of the field office. However, this is NOT a requirements contract. Any increase in the number of contracted hours can only be made by the Contracting Officer and will be done via written contract modification. No on-site changes are authorized.