Interim Changes PGC 03003.docx

SLACK'S, WOMAN'S, POLYESTER/WOOL, GABARDINE

THE DRAWING(S) LISTED BELOW ARE AVAILABLE AT

DLA DURING *OPEN SOLICITATION ONLY*.

TO RECEIVE A COPY OF THE DRAWING(S),

FOR EBS SOLICITATIONS USE URL

HTTPS://WWW.DIBBS.BSM.DLA.MIL/RFQ/

SAMPLING:

THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION, STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.

52.246-15 CERTIFICATE OF CONFORMANCE

RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN

RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT:

http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx

FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.

SKY BLUE 2319

Sample size is 12R . ADDITIONAL INFORMATION FOR MIL-DTL-29432C: . PATTERN DATE: 15 SEPTEMBER 2004 . STANDARD SAMPLE FOR CLOTH, POLYESTER/WOOL GABARDINE 6.8 oz/yd, BLUE 2319 CONFORMING TO TYPE II, CLASS 12 OF MIL-C-10176K IS AVAILABLE ON ROLL NO.3864 SHADE, FINISH AND COLORFASTNESS.

DELETE CURRENT "BARCODE LABEL/TAG" REQUIREMENTS AND SUBSTITUTE THE FOLLOWING:

LABEL TAG: EACH ITEM SHALL BE INDIVIDUALLY BAR-CODED WITH A PAPER TAG FOR PERSONAL CLOTHING ITEMS. THE PAPER USED FOR THE TAGS SHALL BE STANDARD BLEACHED SULFATE HAVING A BASIS WEIGHT OF 100 POUNDS WITH A SMOOTH FINISH TO ACCEPT THERMAL TRANSFER AND DIRECT PRINTING. THE TAGS SHALL HAVE A HOLE AND SHALL BE ATTACHED TO EACH ITEM BY A FASTENER, CLEARLY LEGIBLE AND READABLE BY SCANNER. THE BAR CODING ELEMENT SHALL BE A 13 DIGIT NATIONAL STOCK NUMBER (NSN). THERE SHALL BE A 12 DIGIT UNIVERSAL PRODUCT CODE (UPC) ASSIGNED FOR ALL NSNS BY THE GOVERNMENT. THE INITIAL "UPC" MUST APPEAR BENEATH THE CODE. THE BAR CODES FOR NSN AND UPC SHALL BE A MEDIUM TO HIGH DENSITY AND SHALL BE LOCATED SO THAT THEY ARE COMPLETELY VISIBLE ON THE ITEM WHEN IT IS FOLDED AND PACKAGED AS SPECIFIED. THE LABEL'S LOCATION SHALL CAUSE NO DAMAGE TO THE ITEM.

NOTE: UNIVERSAL PRODUCT CODE INFORMATION THE GOVERMENT ASSIGNED UNIVERSAL PRODUCT CODE (UPC) MUST BE PLACED ON ALL SHIPPING CARTONS ON WHICH THE NSN APPEARS.

THE FOLLOWING DEFECTS APPLY FOR BARCODE LABELS/TAGS:

BAR CODE OMITTED OR NOT READABLE BY SCANNER

HUMAN-READABLE INTERPRETATION (HRI) OMITTED OR ILLEGIBLE

NOT VISIBLE ON FOLDED, PACKAGED ITEM CAUSES DAMAGE TO THE ITEM

NOTE: IF THE END ITEM IS PLACED IN A PLASTIC BAG - USE TYPE VII (PRESSURE SENSTIVE LABEL) OF MIL-DTL-32075.

IF THE END ITEM IS TIED IN A BUNDLE OR LEFT AS AN INDIVIDUAL ITEM, USE TYPE VIII (TAG, PAPER) OF MIL-DTL-32075.

"MIL-DTL-32075: LABEL FOR CLOTHING, EQUIPAGE,

AND TENTAGE, GENERAL USE REPLACES DDD-L-20

(Ref. T0451 - June 19, 2007)

INTERIM SPECIFICATION CHANGES TO MIL-DTL-32075:

PAGE 6, TABLE I, "PHYSICAL REQUIREMENTS OF THE

TYPE VI FINISHED LABEL." UNDER "TEARING

STRENGTH" DELETE: "(LB.) MINIMUM" AND

SUBSTITUTE: "(GNS) MINIMUM."

PAGE 12, PARA 3.3.2.17, AFTER "NSN" ADD

"AND THE UNIVERSAL PRODUCT CODE (UPC)

SUPPLIED BY THE GOVERNMENT, FOR ALL NSNs."

MIL-DTL-10176L Cloth, Gabardine: Wool, Polyester and Wool dated 30-Mar-2018

SPONGING:

COLD WATER SPONGING IS REQUIRED. A PROPER ALCOHOL WETTING AGENT SHALL BE USED TO INSURE SHRINKAGE IS ACCOMPLISHED AND WATER RESISTANT FINISH (when specified) IS NOT RELEASED.

THE WATER REPELLANT TREATMENT (When Specified) SHALL BE APPLIED BEFORE THE SPONGING OPERATION.

WHEN AIR FORCE SHADE 1605 IS SPECIFIED, THE CLOTH SHALL BE PIECE DYED.

ADDITIONAL INFORMATION FOR MIL-C-44296:

INTERIM SPECIFICATION CHANGES TO MIL-C-44296A:

PAGE 1, PARAGRAPH 1.1, SCOPE., LINE 1: AFTER "AND" INSERT "STITCH-REINFORCED NONWOVEN".

PAGE 1, PARAGRAPH 1.2, LINE 12: BETWEEN "TYPE X-CIRCULAR KNIT SUBSTRATE" AND "CLASS 1" INSERT "TYPE X1- "STITCH-REINFORCED NONWOVEN".

PAGE 1, PARAGRAPH 1.2. CLASSIFICATION. BELOW "TYPE IX" ADD "TYPE X - CIRCULAR KNIT SUBSTRATE"

PAGE 2, PARAGRAPH 2. APPLICABLE DOCUMENTS ADD FOLLOWING NEW PARAGRAPH: "2.1.3 OTHER PUBLICATIONS. THE FOLLOWING DOCUMENTS FORM A PART OF THIS DOCUMENT TO THE EXTENT SPECIFIED HEREIN. UNLESS OTHERWISE SPECIFIED, THE ISSUES OF THE DOCUMENTS WHICH ARE DOD ADOPTED SHALL BE THOSE LISTED IN THE ISSUE OF THE DODISS SPECIFIED IN THE SOLICITATION. UNLESS OTHERWISE SPECIFIED, THE ISSUES OF THE DOCUMENTS NOT LISTED IN THE DODISS SHALL BE THE ISSUES OF THE NONGOVERNMENT DOCUMENTS WHICH ARE CURRENT ON THE DATE OF THE SOLICITATION.

AMERICAN ASSOCIATION OF TEXTILE CHEMISTS AND COLORISTS (AATCC) AATCC 20 - FIBER ANALYSIS QUALITATIVE (APPLICATIONS FOR COPIES SHOULD BE ADDRESSED TO AMERICAN ASSOCIATION OF TEXTILE CHEMISTS AND COLORISTS (AATCC), P.O. BOX 12215, TRIANGLE PARK, NC 27709-2215)"

PAGE 3, ADD THE FOLLOWING NEW PARAGRAPH: "3.1.2.10 TYPE X. TYPE X SHALL BE A CIRCULAR KNIT. WHEN SPECIFIED (SEE 6.2), THE FACE SIDE SHALL BE NAPPED."

PAGE 3: AFTER PARAGRAPH 3.1.2.10,ADD THE FOLLOWING: "3.1.2.11 TYPE X1. TYPE X1 SHALL BE STITCH- REINFORCED NONWOVEN WHEREBY A SERIES OF CHAINSTITCHING IS SEWN IN THE MACHINE DIRECTION OF THE SUBSTRATE IN ORDER TO REINFORCE THE NONWOVEN CONSTRUCTION."

PAGE 7, PARAGRAPH 3.4. PHYSICAL REQUIREMENTS. ADD THE FOLLOWING NEW TABLE AFTER TABLE VII:

"TABLE VII. A PHYSICAL REQUIREMENTS FOR TYPE X

STYLE CLASS WEIGHT (INCLUDING BURSTING

ADHESIVE) STRENGTH

OZ/SQ/YD. LBS. (MIN.

MINIMUM MAXIMUM

A 1,2,3 OR 4 1.4 1.8 60

FIBER CONTENT

1/

1/ 100% NYLON OR POLYESTER."

PAGE 7,PARAGRAPH 3.4 PHYSICAL REQUIREMENTS.: AFTER TABLE"V111" ADD NEW TABLE 1X:

"TABLE 1X,PHYSICAL REQUIREMENTS FOR TYPE X1

BREAKING STRENGTH

WGT, OZ/YD2 LBS, (MIN) STITCHING

STYLE CLASS MIN MAX MACH X-MACH CONTENT REIN

FORCEMENT

A 1,2,3 1.0 1.8 10.0 1.0 1/ 2/

1/ 50 TO 100 PERCENT POLYESTER WITH REMAINING PERCENTAGE NYLON OR RAYON.

2/ STITCH REINFORCEMENT CONDUCTED WITH SINGLE MULTIFILAMENT THREAD USING CHAINSTITCH STITCH TYPE WITH CHAINSTITCH LOOPS ON FUSIBLE SIDE TO PROTECT FROM UNRAVELING."

PAGE 7, PARAGRAPH 3.4.1. BONDING STRENGTH.

- LINE 2, DELETE "(EXCEPT CLASS 5)" AND SUBSTITUTE "(EXCEPT TYPE IX WHEN USED AS FUSIBLE SEAM TAPE AND CLASS 5)".

- LINES 7 AND 8, DELETE "OR SHEETING MATERIAL".

PAGE 9, PARA. 4.2.2.1, LINE 22, DELETE "30" AND SUBSTITUTE "20". LINE 24, DELETE "45" AND SUBSTITUTE "30".

PAGE 11, TABLE VIII. END ITEM TESTS UNDER TEST METHOD COLUMN, LINES 2 AND 3 DELETE "1600" AND SUBSTITUTE "AATCC 20".

PAGE 12, PARAGRAPH 4.3.1.1. BONDING STRENGTH PROCEDURE (INITIAL AND AFTER LAUNDERING/DRY CLEANING). DELETE THE FIRST AND SECOND SENTENCES IN THEIR ENTIRETY AND SUBSTITUTE: "CUT A 12 INCH WARP BY 11 INCH FILLING SAMPLE FROM BOTH THE OUTERSHELL AND FUSIBLE MATERIALS SPECIFIED FOR CONTRACT USE (SEE 6.5)."

PAGE 15: AT THE END OF PARAGRAPH 6.1.1,ADD THE FOLLOWING:

" E. STITCH REINFORCED NONWOVEN TYPE X1 OFFERS HIGH DEGREE STRENGTH/STABILIZATION FOR TAPE AND STAY APPLICATION FOR LARGE OR SMALL PART FUSIBLES AND IS INTENDED TO PROVIDE VERTICAL STABILITY AND ABRASION RESISTANCE."

PAGE 16, PARAGRAPH 6.5. BONDING STRENGTH DISPUTE PROCEDURE. INSERT THE FOLLOWING BETWEEN THE FIRST AND SECOND SENTENCES: "IN SOME CASES, OUTERSHELL SAMPLES REPRESENTATIVE OF SEPARATE PRODUCTION LOTS MAY BE USED TO DETERMINE IF DIFFERENT FINISHES MAY AFFECT BONDING STRENGTH."

(ref. T0998 - 5/23/06)

ADDITIONAL INFORMATION FOR MIL-STD-984:

MIL-STD-984A: PROVISION FOR SIZE LABELING FOR

WOMEN'S UNIFORM CLOTHING 13 SEPT 1994.

EACH WOMAN'S ITEM SHALL HAVE A SEPARATE

SIZE LABEL CONFORMING TO TYPE VI CLASS 2 OF

MIL-DTL-32075 AND BODY DIMENSION LABELING

REQUIREMENT CONFORMING TO MIL-STD-984. THE

LABEL SHALL INDICATE SIZE, BODY DIMENSIONS,

AND STOCK NUMBER AS SHOWN BELOW:

FOR DRESS COATS:

SIZE CODE: 12JP (EXAMPLE)

BUST CIRC: 37-1/2 (EXAMPLE)

HIP CIRC: 38 (EXAMPLE)

HEIGHT: LESS THAN 63 1/2 (P) (EXAMPLE)

FOR SLACKS AND SKIRTS:

SIZE CODE: 12 JP (EXAMPLE)

WAIST CIRC: 29-1/2 (EXAMPLE)

HIP CIRC: 38 (EXAMPLE)

HEIGHT: LESS THAN 63 1/2 (P) (EXAMPLE)

PAGE 5, TABLE 1, ADD THE FOLLOWING SIZES:

HEIGHT: LESS THAN 63 1/2 (P) (EXAMPLE)

STOCK NO: 8410-00-000-0000 (EXAMPLE)

NOTE: ABBREVIATIONS FOR THE APPLICABLE BODY TYPE

SHALL BE "J" FOR JUNIORS , "M" FOR MISSES AND

"W" FOR WOMEN'S.

ABBREVIATIONS FOR THE APPLICABLE LENGTHS SHALL

BE "P" FOR PETITE, "R" FOR REGULAR, AND "T" FOR

TALL.

NOTE: THE INFORMATION FOR EACH SIZE LABEL IS

CONTAINED IN MIL-STD-984 AND IS NOT TO BE

CONFUSED WITH THE FINISHED DIMENSIONS OF THE END

ITEM IN THE SPECIFICATION.

INTERIM CHANGES TO MIL-STD-984:

PAGE 5, TABLE I, DELETE IN ITS ENTIRETY AND

SUBSTITUTE THE FOLLOWING:

SIZE CODE BUST CIRC WAIST CIRC HIP CIRC

INCHES INCHES INCHES INCHES

2M 31-1/2 23-1/2 34 4J 32-1/2 24-1/2 33 4M 32-1/2 24-1/2 35 4W 32-1/2 24-1/2 37 6J 33-1/2 25-1/2 34 6M 33-1/2 25-1/2 36 6W 33-1/2 25-1/2 38 8J 34-1/2 26-1/2 35 8M 34-1/2 26-1/2 37 8W 34-1/2 26-1/2 39 10J 36 28 36-1/2 10M 36 28 38-1/2 10W 36 28 40-1/2 12J 37-1/2 29-1/2 38 12M 37-1/2 29-1/2 40 12W 37-1/2 29-1/2 42 14J 39 31 39-1/2 14M 39 31 41-1/2 14W 39 31 43-1/2 16J 41 33 41-1/2 16M 41 33 43-1/2 16W 41 33 45-1/2 18J 43 35 43-1/2 18M 43 35 45-1/2 18W 43 35 47-1/2 20J 45 37 45-1/2 20M 45 37 47-1/2 20W 45 37 49-1/2 22J 47 39 47-1/2 22M 47 39 49-1/2 22W 47 39 51-1/2 24J 49 41 49-1/2 24M 49 41 51-1/2 24W 49 41 53-1/2 26J 51 43 51-1/2 26M 51 43 53-1/2 26W 51 43 55-1/2 28J 53 45 53-1/2 28M 53 45 55-1/2 28W 53 45 57-1/2 MIL-STD-129R w/CHANGE 2 - DEPARTMENT OF DEFENSE STANDARD PRACTICE MILITARY MARKING FOR SHIPMENT AND STORAGE

DATED: 27 SEPTEMBER 2019

INTERIM CHANGES:

OMISSION OF MARKINGS ON EXTERIOR SHIPPING CONTAINERS OF ITEMS

IN THE DLA TROOP SUPPORT CLOTHING AND TEXTILE (C&T) DIRECTORATE:

THE NOMENCLATURE AND MANUFACTURER'S NAME (WHEN THE NAME IDENTIFIES THE MATERIAL) SHALL BE OMITTED FROM ALL EXTERIOR SHIPPING CONTAINERS OF DLA TROOP SUPPORT C&T ITEMS, REGARDLESS OF MODE OF SHIPMENT.

IF THE MANUFACTURER'S NAME DOES NOT IDENTIFY THE MATERIAL AS BEING CLOTHING, IT MAY REMAIN. NSNS SHALL BE SHOWN ON ALL SHIPPING CONTAINERS OF C&T ITEMS, THE PACKING LIST SHALL BE PLACED INSIDE THE LAST CONTAINER TO BE LOADED FOR EACH SHIPMENT. THE WORDS "PACKING LIST HERE" SHALL BE STENCILED, NOT HAND LETTERED, ON THE CONTAINER.

ADDITIONAL INFORMATION FOR MIL-STD-656:

INTERIM CHANGES TO MIL-STD-656C

PAGE 18, DEFECT XV. POCKET OR FLAPS, S.

HIP POCKET: ADD NEW DEFECT:

"3. CORD (WELTS) OUT OF HORIZONTAL ALIGNMENT

WITH WAISTBAND WHEN MEASURED FROM BOTTOM OF

WAISTBAND TO TOP CORNERS OF WELT BY:

. D S U

-MORE THAN 1/2 INCH * 3 2

-MORE THAN 1/4 UP TO 1/2 INCH 3 3 2

-UP TO 1/8 MORE 1/4 INCH 2 2 1

INTERIM CHANGES TO MIL-STD-656C:

PAGE 5, TABLE I DELETE IN ITS ENTIRETY AND

SUBSTITUTE "TABLE I SAMPLING PROVISIONS FOR END

ITEM VISUAL EXAMINATION OF DRESS (D) SLACKS:

NORMAL INSPECTION:

LOT SIZE SAMP SIZE MAX ACCP PT VALUE

. 3&2 PT 3.2 &1 PT

. DEFECTS DEFECTS

UP THRU 90 20 3 PT 6 PT

91 - 150 32 5 PT 9 PT

151 - 280 50 7 PT 13 PT

281 - 500 80 9 PT 17 PT

501 - 1200 125 14 PT 25 PT

1201 - 3200 200 18 PT 33 PT

REINSTATE NORMAL INSPECTION (SEE 5.5.4B). THE

3201 - 10,000 315 24 PT 48 PT

SECOND VALUE IS THE MAXIMUM ACCEPTABLE POINT

10,001 - 35,000 500 35 PT 72 PT

35,001 AND OVER 800 55 PT 110 PT

TIGHTENED INSPECTION:

UP THRU 150 32 2 PT 5 PT

151 - 280 50 3 PT 7 PT

281 - 500 80 5 PT 11 PT

501 - 1200 125 9 PT 17 PT

1201 - 3200 200 13 PT 26 PT

3201 - 10,000 315 20 PT 39 PT

10,001 - 35,000 500 30 PT 59 PT

35,001 AND OVER 800 45 PT 89 PT

REDUCED INSPECTION:

UP THRU 280 20 2-6 PT 11 PT

281 - 500 32 3-9 PT 15 PT

501 - 1200 50 5-10 PT 18 PT

1201 - 3200 80 8-13 PT 24 PT

3201 - 10,000 125 12-17 PT 28 PT

10,001 - 35,000 200 17-21 PT 33 PT

35, 001 AND OVER 315 23-29 PT 47 PT

1/ IF THE FIRST VALUE IS EXCEEDED BUT THE SECOND

VALUE HAS NOT BEEN EXCEEDED, ACCEPT THE LOT BUT

REINSTATE NORMAL INSPECTION (SEE 5.5.4B). THE

SECOND VALUE IS THE MAXIMUM ACCEPTABLE POINT

VALUE.

TABLE II DELETE IN ITS ENTIRETY AND SUBSTITUTE

"TABLE II SAMPLING PROVISIONS FOR END ITEM

VISUAL EXAMINATION OF SEMI-DERSS (SD) SLACKS"

NORMAL INSPECTION:

LOT SIZE SAMP SIZE MAX ACCP PT VALUE

. 3&2 PT 3.2.&1 PT

. DEFECTS DEFECTS

UP THRU 500 50 7 PT 14 PT

501 THRU 1200 80 9 PT 20 PT

1201 THRU 3200 125 14 PT 26 PT

3201 THRU 10,000 200 19 PT 38 PT

10,001 THRU 35,000 315 27 PT 57 PT

35,001 AND OVER 500 41 PT 85 PT

TIGHTENED INSPECTION:

UP THRU 500 50 3 PT 10 PT

501 THRU 1200 80 5 PT 15 PT

1201 THRU 3200 125 8 PT 23 PT

3201 THRU 10,000 200 12 PT 34 PT

10,001 THRU 35,000 315 19 PT 52 PT

35,001 AND OVER 500 27 PT 78 PT

REDUCED INSPECTION:

UP THRU 1200 32 3-8 PT 15 PT

1200 THRU 3200 50 5-9 PT 18 PT

3201 THRU 10,000 80 8-12 PT 24 PT

10,001 THRU 35,000 125 11-15 PT 31 PT

35,001 AND OVER 200 15-53 PT 43 PT

1/ IF THE FIRST VALUE IS EXCEEDED BUT THE SECOND

VALUE HAS NOT BEEN EXCEEDED, ACCEPT THE LOT BUT

REINSTATE NORMAL INSPECTION (SEE 5.5.4B). THE

SECOND VALUE IS THE MAXIMUM ACCEPTABLE POINT

VALUE.

TABLE III DELETE IN ITS ENTIRETY AND SUBSTITUTE

"TABLE III SAMPLING PROVISIONS FOR END ITEM

VISUAL EXAMINATION OF UTILITY (U) SLACKS"

NORMAL INSPECTION:

LOT SIZE SAMP SIZE MAX ACCP PT VALUE

. 3&2 PT 3.2 & 1 PT

. DEFECTS DEFECTS

UP THRU 500 50 9 PT 17 PT

501 THRU 1200 80 13 PT 20 PT

1201 THRU 3200 125 18 PT 29 PT

3201 THRU 10,000 200 25 PT 42 PT

10,001 AND OVER 315 39 PT 62 PT

TIGHTENED INSPECTION:

UP THRU 500 50 5 PT 11 PT

501 THRU 1200 80 8 PT 17 PT

1201 THRU 3200 125 12 PT 25 PT

3201 THRU 10,000 200 19 PT 38 PT

10,001 AND OVER 315 27 PT 57 PT

REDUCED INSPECTION:

UP THRU 1200 32 5-9 PT 16 PT

1201 THRU 3200 50 8-12 PT 20 PT

3201 THRU 10,000 80 11-14 PT 25 PT

10,001 AND OVER 125 15-19 PT 29 PT

1/ IF THE FIRST VALUE IS EXCEEDED BUT THE SECOND

VALUE HAS NOT BEEN EXCEEDED, ACCEPT THE LOT BUT

REINSTATE NORMAL INSPECTION (SEE 5.5.4B). THE

SECOND VALUE IS THE MAXIMUM ACCEPTABLE POINT

VALUE.

PAGE 20, UNDER XX LABEL ADD THE FOLLOWING:

D. BAR CODE LABEL/TAG

DEFECT POINT VALUE

. D SD U

1. BAR CODE OMITTED OR NOT

. READABLE BY SCANNER. 1 1 1

2. HUMAN READABLE INTERPRETATION

. (HRI) OMITTED OR

. ILLEGIBLE 1 1 1

3. NOT VISIBLE ON FOLDED,

. PACKAGED ITEM. 1 1 1

4. CAUSES DAMAGE TO THE

. ITEM. 3 3 3".

(Ref. T0320)