5180014998353 IPD.pdf

ITEM PURCHASE DESCRIPTION

General Services Administration

5180-01-499-8353 Ver: 9 UI: KT Status: Active AAC: J

TOOL KIT, VEHICLE, TACTICAL

NSN Description:

In accordance with U.S. Army Tank-Automotive and Armaments Command Drawing Number 57K4590

KEY FIELDS:

HEADER INFORMATION

The following header paragraph(s) shall apply to the item purchase description(s) where applicable. If there is a conflict between the item purchase description and the header paragraph(s), the header paragraph(s) shall take precedence over the item purch ase description.

Notwithstanding the requirements specified herein, cadmium plating is not acceptable. In the event no alternative coating, finish, or plating is specified, a rust preventative finish as used in standard commercial practice shall apply.

When chromium plating or finish is specified and the manufacturer has a commercial coating of the same color and texture of chromium that the manufacturer uses in lieu of chromium; then the alternative coating can be used, provided the coating meets Aerospace Standard SAE AS4984.

Each set or kit shall contain a dated parts list or packing list citing the GSA contract number (if applicable), GSA purchase order number, date of purchase order, kit national stock number (NSN), each component NSN (if a pplicable), kit noun name, each component noun name, and quantity of each component.

Unless otherwise specified in the item purchase description, each kit or set and each component of the kit or set shall have, in addition to any other required marking , identification marking indicating the manufacturer's name or identifying symbol, and the state or country of manufacture. The marking shall be engraved, etched, or stamped in such a manner that it will be permanent to the extent that it will remain cle ar and legible throughout the life of the item.

Workmanship: Details of workmanship shall be in accordance with the best commercial standards and practices. Paints, coatings, platings, and finishes shall be smooth, adherent, continuous, and not staine d or discolored. Fasteners shall be firmly secured and show no evidence of deformation, cross threading, or hazardous burrs. Adhesives and lubricants adequate for their intended purpose shall be properly and neatly applied. Adhesives shall be adequatel y cured. Wires and cables shall be neatly dressed and shall not be frayed or in contact with sharp edges. Wire and cable insulation shall show no evidence of burns, abrading, or pinch marks. There shall be no interference, binding, or galling of parts. External and bearing surfaces shall be free of tool and gouge marks, nicks, or other surface imperfections. The item shall be clean and free of corrosion and debris (e.g. chips shavings, slivers) or other foreign material. The item shall be free from manufacturing workmanship defects (e.g., loose, missing, binding or misaligned parts, sharp or rough external edges, corners or surfaces) and material defects (e.g., pits, rips, fins, burrs, tears, nodules, cracks, blisters) which may adversely

Printed on: 08/06/2026 Page 1 impact the item's serviceability, durability, safety, or appearance.

TECHNICAL DOCUMENT

In accordance with US Army Tank-Automotive and Armaments Command, drawing 57K4590, dtd 4/18/2003; Special Packaging Instruction, dtd 5/9/2003, Notice of Revision, dtd 9/7/2005.

EXCEPTION(S) TO TECHNICAL DOCUMENT

Mark each tool in a permanent and legible manner with drawing number, manufacturer's name or identifying symbol, and country of origin

ITEM MARKING

Each item Shall Be Marked in a Permanent and Legible Manner with:

1) Manufacturer's Part Number

2) Manufacturer's Name or Identifying Symbol, and

3) Country of Origin

Each Package including the unit, single, intermediate, and exterior container mu st be labeled with the requisition number or Transportation Control Number (TCN). Requisition Number and TCN are found on the Purchase Order.

PACKAGING

Preservation/Packing: Each tool kit shall be packed in a close fitting fiberboard box that will offer protection during shipping, handling, storage and redistribution. The packed tool kit shall be marked in accordance with standard commercial practice.

Shipping Container: Each kit shall be packed as stated above and the quantity of kits packaged per shipping container shall be uniform. The shipping container shall be packed in a close fitting fiberboard box in compliance with the Uniform Freight Class ification and the National Motor Freight Classification requirements of Rules, Item 222, Sec. 3., Minimum 200 or ECT 32.

MARKING

MARKING

In general, unless otherwise specified by the contracting officer, marking of shipments shall be in accordance with the GSAM provision/ Clause 552.211-73, marking. In more detail: Marking of supplies for deliveries to domestic civilian activities shall comply with the latest edition of Federal Standard 123. That is, unit, intermediate, and transport packages shall be marked directly on the side surface of the package or on a label affixed to the package, with the identification marking as specifi ed in the standard. Transport packages shall also have, in addition to the identification marking, a shipping label that includes the purchase order, contract, or the requisition numbers; as applicable, including the consignor and consignee names (i.e. sh ip from/ to), gross weight, cube and piece number.

Marking of supplies for deliveries to civilian activities, export locations, including commercial freight forwarders and third party logistics providers, and excluding freight entering the Defense Tran sportation System, shall be the same as deliveries

Printed on: 08/06/2026 Page 2 to domestic locations except that the shipping label shall show on the same label, or another label affixed next to the shipping label, the ultimate consignee (i.e. Mark for AAC).

Marking of supplies f or deliveries to domestic military activities shall comply with the latest edition of Military Standard

129. That is, unit, intermediate, and exterior or shipping containers shall be marked directly on the side surfaces of the package or on a label affixe d to the package, with the identification marking as specified in the standard. Exterior or shipping containers shall also have in addition to the identification marking, a Military Shipping Label (MSL) per the standard.

Marking of supplies for deliver ies to military activities, export locations, including forwarding and container consolidation points (CCPs) shall be the same as deliveries to domestic locations except that the MSL must also show the ultimate consignee (Mark for DoDAAC) and the Transpor tation Control Number (TCN).

"Latest version" is defined as the version in effect on the date of bid submittal. Federal Standards and Military Standards can be accessed on-line via the Defense Logistics Agency's "Assist" Quicksearch web site: http://qu icksearch.dla.mil/

PACKAGING/ PACKING

Unless packaging in accordance with MIL-STD-2073-1 Standard Practice for Military Packaging is specified in the solicitation, contract or order, packaging/ packing of supplies, exclusive of hazardous material, f or domestic and export shipments to civilian and military activities shall comply with GSAM Provision/ Clause 552.211-75 Preservation, Packaging and Packing which references the National Motor Classification Standard (NMFC) and/ or the latest requirements of ASTM D-3951, Standard Practice for Commercial Packaging . Until the commercial packaging/ packing requirement in GSAM Clause 552.211-75 is revised, compliance to either the GSAM clause or the ASTM D-3951, Standard Practice for Commercial Packaging wi ll be acceptable; however, compliance to the ASTM requirements is mandatory for GSS contracts, and is preferred for all other contracts. In case of conflict between the GSAM clause and the revision of ASTM D-3951, the ASTM requirement shall govern.

Pac kaging of hazardous material (HM) supplies for shipments shall comply with the GSAM provision/ Clause 552.223-73, Preservation, Packaging, Packing, Marking and Labeling of Hazardous Materials (HAZMAT) for Shipments . That is, packing of HM for domestic s hipments shall comply with the latest versions of DOT HMR in 49 CFR, parts 171-180, and OSHA HCS in 29 CFR, part 1910.1200.

Packing of HM for export shipments (includes forwarding and container consolidation points, commercial freight forwarders and th ird party logistics providers) shall comply with the latest versions of DOT HMR in 49 CFR, parts 171- 180, and OSHA HCS in 29 CFR, part 1910.1200, and the applicable IMDG, IATA, ICAO, AFMAN-24 standard for the mode of transportation.

WOOD PACKAING MATER IAL

Packaging and packing of supplies using Wood Packaging Material (WPM) on a pallet or skid for export shipments (includes forwarding and container and consolidation points, commercial freight forwarders and third party logistics providers) shall compl y with the requirements in provision/ Clause GSAM 552.211.89, Manufactured Wood Packaging Material for Export or the applicable requirements in ASTM D-3951 relative to the WPM. That is, all wood shall be treated and stamped appropriately for export, inc luding the actual pallet or skid, if made of wood.

PALLETIZATION AND PREPARATION FOR DELIVERY

Printed on: 08/06/2026 Page 3

The item(s) shall be packaged and packed to afford adequate protection against physical damage during shipment from the supplier to the first receiving activ ity. The pack shall comply with the rules and regulations applicable to the mode of transportation. If pallet or skid is used for shipping, it shall be made in accordance with normal industry standards. In the event a wood pallet or skid is used for shipp ing, the requirements of GSAM 552.211.89, Non-Manufactured Wood Packaging Material for Export, shall apply.

ITEMS REQUIRING SAFETY DATA SHEETS (SDSs) Items requiring Safety Data Sheets (SDSs) shall be provided by the contractor as specified in IPD and the FAR Provision/Clause 48 CFR 52.223 3 Hazardous Material Identification and Material Safety Data, and the latest version of Federal Standard 313. One copy of the SDS shall be included inside or affixed to the outside of each transport package. If a ffixed outside the SDS must be placed in a weather resistant envelope.

Data in all 16 sections of the OSHA HazCom/ GHS standards will be required. HM shall be labeled with an OSHA/ GHS compliant label to include the following data: (1) Product identif ier, (2) Signal Word, (3) Hazard Statements, (4) Pictograms,

(5) Precautionary Statements, and (6) Chemical Manufacturer, Importer, or Other Responsible Party information.

Printed on: 08/06/2026 Page 4