Specifications_-_revision_1.pdf

Purchase of Thirty-eight (38) Interior Hollow Metal Doors per specifications for DOI, Bureau of Indian Affairs, Rosebud Agency, Bldg#1004, located at 1004 Omaha Street, Mission, SD 57555. DOI, BIA personnel will be completing installation of all doors.

Measurements: Measurements provided. Drawings Attached. Door dimensions are to fit existing door frames.

Door frames will not be replaced. There is no code requirement for fire rating in accordance with NFPA 101,39.3.6 and NFPA 101, 39.3.7

Sixteen (16) 32” Wide (RH) Right Hand Swing-In; Door Opening Height 80” and Door Opening Width 32”

Fifteen (15) 32” Wide (LH) Left Hand Swing-In; Door Opening Height 80” and Door Opening Width 32”

Total = (31) 32” Wide HM Doors

Three (3) 36” Wide (RH) Right Hand Swing-In; Door Opening Height 80” and Door Opening Width 36”

One (1) 36” Wide (LH) Left Hand Swing-In; Door Opening Height 80” and Door Opening Width 36”

Two (2) 36” Wide (LHR) Left Hand Swing-Out; Door Opening Height 80” and Door Opening Width 36”

One (1) 36” Wide (RHR) Right Hand Swing-Out; Door Opening Height 80” and Door Opening Width 36”

Total (7) 36” Wide HM Doors

All Doors must meet the following specifications, includes all accessories and any freight charges:

• HM CRS Doors shall be formed from two 18 gauge A60 Galvannealed Steel per ASTM A924 and A653 and shall be 1-3/4″ thick.

• CRS doors shall be formed from two 16 or 18 gauge A60 Galvannealed steel per ASTM A924 and A653 and shall be 1-3/4″ thick.

• All hinge reinforcements shall be 3/16″ thick. Door hinges are 4 hole with a screw pattern.

• All doors shall be internally reinforced with a 12 gauge plate on both sides of the door for application of surface applied door closures and holders.

• Glass light molding shall be Pioneer standard steel molding, with no exposed screws on the secure side of door.

• All doors shall be manufactured in accordance with UL or WHI procedures and bear the appropriate classification mark (label).

• Door construction shall comply with ANSI A250.8-2003 (SDI 100)

• Hardware reinforcements shall be in accordance with ANSI A 250.8-2014. Locations shall be in accordance with

ANSI/BHMA A156.115

• Doors shall have one coat of baked-on rust inhibitive metal primer in compliance with ANSI A250.10-2004.

Doors should then be painted one color on both sides. Final paint color to be selected by contractor, off white or eggshell.

• Standard 345/161, Hinge & Lock Preps

• Top of Door to top of hinges: 4-7/8”, 37-1/8”, 69-3/8” – See attached individual door drawings for small variations.

• Top of Door to centerline of lock: 41-7/8” – See attached individual door drawings for small variations.

• Hager 5200 x ALM x MLT/Adj 1-6 Door Closures

• Hager 3553 x WTN x US26D x 2-3/4 x ASA X SCC-KD Entrance Lever Lockset

• Hager ECBB1100 4.5 x 4.5 US26D Ball Bearing Hinges

• Hager 190S 10 x 34 US32D Kick Plate

• Steel Lite Kit – VSL – 6 x27 – Bronze – ¼” Glass, 1-3/4” Thick Door

• 5 x 26 x ¼” Clear Tempered Glass

• Rekey Standard Key Cylinder

Point of Contact: Leota Colombe, Supervisory Facility Operations Specialist, 605-856-4405