36C25619R0024-0002004.pdf

DNH AS

Phone................... + 47 35 98 56 00 Fax………............. + 47 35 98 56 10 E-mail...………............ dnh@dnh.no Web-Site…………….. www.dnh.no

DNH WW Ltd Phone……. + 44 1908 275 000 Fax.............+ 44 1908 275 100 E-mail…..........dnh@dnh.co.uk

DNH Speakers Inc Phone........... + 1 484 494 5790 Fax…........... .+ 1 484 494 5793 E-mail..dnh@dnhspeakers.com

DNH GmbH Phone… + 49 040 6569 30-0 Fax....... + 49 040 6569 30-30 E-mail...........…. dnh@dnh.de

ISO 9001 CERTIFIED

DNH reserves the right to alter specifications without notice

HEAD OFFICE, NORWAY ENGLAND GERMANY USA

T:\Dataark\DOC-format\CLEANROOM\BPF560CRT.doc Rev. 24.03.2017

BPF-560CR(T)

Installation, Operation and Maintenance Procedures

Install ring into the cutout hole turning the screws connected to the three hooks, screw clockwise until the ring is fixed to the ceiling.

Hooks can be mounted both ways to fit the thickness of the roof, see drawing at top of the page.

Remove box by one screw. Lead cable in to the box, connect cable to terminal (70V or 100V) and select required tapping on the transformer.

Install box by one screw. Turn the grill gently clockwise within the ring until it stops.

BPF-560CR(T) is designed for clean room applications.

For optimum performance, always use the correct voltage / power and operate within the frequency limits as stated.

Do not open loudspeaker when energized.

This loudspeaker is supplied with a two years warranty against defective workmanship.

Sound pressure levels at 1W/1m Specifications Material / Color PA / ABS / RAL9010 Mounting Hooks Termination Spring clamp Weight w/transformer 0,9 kg IP-rating NA Max. / min. amb. temp 90C / -20C Rated / max. power 6 W / 10 W SPL 1W/1m 88 dB SPL rated power 95 dB Effective freq. range 150 – 11000 Hz Dispersion (-6dB) 1kHz / 4kHz 170 / 60 Options Impedances, colors, labels

70/100 Volt combined transformer

Primary connections White : Green 70 V White : Red 100 V

Secondary nominal tappings

C : 6W 6,0 W C : 3W 3,0 W C : 1,5W 1,5 W C : 0,5W 0,5 W

Overview

The 6400 electric door strike from Von Duprin is designed to be modular and highly configurable to fit nearly any mortise or cylindrical lock. This versatile strike allows the installer to insert and lock-in the deadbolt keeper or plug and deadlatch ramp anywhere within its 3-1/8” vertical opening to fit the latch position and functional needs. This, combined with a 1 ⁄8” horizontal adjustment, makes this easy-to-install design a good fit for installations where misalignment or a tight fit may be a problem.

As a 3-hour UL 10C listed strike, the 6400 Series is intended as a fail-secure only solution for fire-rated openings. Its durability and quality are shown by its UL 1034 listing, heavy-duty stainless steel construction and over 2,000,000 cycles endurance testing.

Use it as a time-saving, “go to” strike. The 6400 comes ready for use with prewired plug-in connectors for 12 or 24 VDC voltage that can be changed over to 12 or 24 VAC without a converter kit, two faceplates – one each for offset and centerline locks as well as a trim filler plate, mounting tabs and shims and a self-adhesive template for frame cuts. An optional “plug in” latchbolt monitor is also available and can be added in the field at any time after installation.

Features and benefits

§ Modular design fits cylindrical and nearly any mortise lock

§ Heavy-duty stainless steel construction in BHMA 630 satin finish

§ Vertical adjustments allow for alignment with a wide variety of mortise locks with offset latches

§ Horizontal adjustment of up to 1⁄8” improves fit on tight door preps

§ Can accommodate up to 1” deadbolt (for night latch only)

§ Field selectable voltage 12 or 24VDC and 12 to 24VAC

§ Plug-in voltage connectors are included for ease of installation and removal during strike servicing

§ Optional plug-in latchbolt monitor can be added in the field

§ Non-handed, unique internal solenoid design prevents keeper from heating up

§ Low current draw (0.19 amps @ 24 VDC)

§ Suitable for interior and exterior doors

§ 3-hour fire-rated to UL 10C (fail secure only)

§ UL 1034 listed for burglary-resistant electric door strikes

§ Meets ANSI/BHMA A156.31, Grade 1 for endurance and dynamic strength

§ Meets ANSI/BHMA A156.31, Grade 1, 1500 lbs static strength

§ Dynamic strength 70 ft-lbs

§ Endurance 2,000,000 cycles

6400 Series Modular strike for mortise and cylindrical locksets

Von Duprin • 6400 Series

6400 Series power requirements Model Mode Voltage Duty Sound Amps1 Ohms2

6400 Fail-locked 12 VDC Continuous Silent .375 37

6400 Fail-locked 24 VDC Continuous Silent .190 148

6400 Fail-locked 12-24 VAC Intermittent Buzz .280 - .565 37

Intermittent duty = Energized less than 1 min. with duty ratio 1:5; Continuous duty = Energized 1 min. or more.

1 Ratings are based on maximum current draw at +10°C and include initial power-up current draw.

2 Nominal resistance at +25°C +/- 7% tolerance.

Red Black

-Red

Black

24VDC

Terminal

12VDC

12-24VAC

Terminal

N O

N C

C

Latch Monitor

Optional LM

Lockset compatibility

Vertical adjustment of the deadbolt keeper or deadlatch ramp allows for alignment with a wide variety of mortise locks with offset latches.

Accommodates up to 1" deadbolt*. Up to 1⁄8" horizontal adjustment for misaligned frames.

* Night-latch function only, bolt will not release

Wiring Instructions

Use the appropriate wire harness supplied.

§ 12V for 12VDC & 12-24VAC

§ 24 for 24VDC only

Attach the red wire to (+) positive of the power supply. Attach the black wire to the (-) negative of the power supply. If using AC power, polarity is not observed.

Note: If a suppression diode is required for access control, observe proper polarity.

Latch monitor wires

Black = Common (C)

Blue = Normal Close (NC)

Orange = Normal Open (NO)

Model specifications

Model number 6400

Latchbolt throw 3⁄4" (also accomodates 1" deadbolt as a nightlatch only - no release)

Face plate length 4 7⁄8"

Backbox depth 1 3⁄4"

Finish BHMA 630 / US 32D

Lockset Cylindrical, mortise, mortise exit

Number of doors Single

Door/frame type Hollow metal, aluminum & wood

Options EB (entry buzzer)

Certifications UL 1034 burglary-resistant listed & 3-hour fire rated to UL 10C (fail-secure only)

Application notes Modular electric strike ideal for aftermarket applications.

Fail-secure only for fire-rated openings.

Von Duprin • 6400 Series

Dimensions

1-1/4" (31.8 mm)

3/4" (19.0 mm)

4-1/8" (104.8 mm)

4-7/8" (123.8 mm)

5/8" (15.9 mm)

1-5/8" (41.3 mm)

1/4" (6.3 mm)

1-5/8" (41.3 mm)

1-3/8" (34.9 mm)

3-1/8" (79.4 mm)

1-1/4" (31.8 mm)

5/8" (15.9 mm)

4-7/8" (123.8 mm)

4-1/8" (105.0 mm)

1-1/2" (38.1 mm)

4-5/8" (117.5 mm)

3-1/4" (82.5 mm)

3/8" (9.5 mm)

3-3/8" (85.7 mm)

Faceplate for offset locks

Faceplate for centerline locks (included)

1-3/4" (44.5 mm)

Note: Not to scale. Specifications are subject to change without notice.

Ordering information

Selections correspond with the numbers above

6400-EB

1 Model 6400 Modular Strike

2 Buzzer (optional) EB Entry buzzer

M o d e l

B u zz e r*

1 2

Accessories § LM6400 Latchbolt monitor - indicates when door is latched

(ships separately)

Standard features § Power failure mode: Fail-secure only (FSE)

§ Voltage: Field selectable 12 or 24 VDC and 12 or 24 VAC voltage

§ Finish: Stainless steel, satin (BHMA 630/US 32D)

§ Centerline and offset face plates included

§ Also includes: two plug-in voltage connectors, self-adhesive template for frame cuts, trim filler plate, mounting tabs and shims, as well as tamper-resistant screws with a security driver bit

* Optional

About Allegion

Allegion (NYSE: ALLE) is a global pioneer in safety and security, with leading brands like CISA®, Interflex®, LCN®, Schlage® and Von Duprin®. Focusing on security around the door and adjacent areas, Allegion produces a range of solutions for homes, businesses, schools and other institutions. Allegion is a $2 billion company, with products sold in almost 130 countries. For more, visit www.allegion.com.

This page intentionally left blank.

© 2016 Allegion

009011, Rev. 04/16 www.allegion.com/us

Allegion, the Allegion logo, Von Duprin and the Von Duprin logo are trademarks of Allegion plc, its subsidiaries and/or affiliates in the

United States and other countries. All other trademarks are the property of their respective owners.

Technical Data Guide Polyether Technology CSI Section No. 07 92 13

Product Description M-1CR (clean room) is solvent-free, extremely low VOC, moisture curing, polyether adhesive-sealant designed for application in areas where outgassing and solvents are not tolerated. It releases virtually no molecular air contamination and contains no isocyanates. M-1CR will not shrink upon curing, will not discolor when exposed to UV light, and can not “out-gas” on damp surfaces as is common with urethane sealants. The product has resilient “elastomeric” properties and excellent adhesion to most construction materials. M-1CR is designed for environments where molecular airborne contamination can impact human health or clean room manufacturing operations and is specified for biomedical, electronic and aerospace clean rooms.

Applicable Performance Standards

• ASTM C920, Type S, Grade NS, Class 25, Uses NT, T1, M, G, A, and O

• Federal Specification TT-S-00230-C Type II, Class B

• Corps of Engineers CRD-C-541, Type II, Class B

• Canadian Standards Board CAN 19, 13-M82

Storage Store original, unopened containers in a cool, dry area.

Protect unopened containers from water, heat and direct sunlight. Elevated temperatures will reduce shelf life.

M-1CR will not freeze.

Last Revision: 09/25/15

Advantages

• 100% VOC Compliant less than 15 grams/liter

• Tough elastomeric bonds

• Solvent Free

• Fast Setting

• High adhesion

• Paintable within 24 hours

• Gun grade, no special tools or mixing required

• Can be applied at temperatures as low as 32°F (0°C)

Colors

Gray White

* Color matching is available in batch quantity only

Packaging

• 10.1 oz (300 ml) 16 cartridges/field pack, 48 field packs/pallet

• 20 oz (600 ml) available by special order 12 sausages/carton, 45 cartons/pallet

• 5 gallon pails or 50 gallon drums available by special orderShelf Life

Twelve months from date of manufacture when stored at 70°F / 21°C with 50% relative humidity. High temperature and high relative humidity may significantly reduce shelf life.

Pails have a shelf life of six months.

Regulatory Compliance

• Conforms to OTC Rule for Sealants and Caulks

• Meets requirements of California Regs:

CARB, BAAQMD and SCAQMD

• This product does not contain cancer causing chemicals listed in California Proposition 65

• Conforms to USDA Requirements for Non-food Contact

Document No. L1271 Chem Link Construction & Maintenance Telephone: 800-826-1681 Fax: 269-679-4448 353 E. Lyons Street Schoolcraft, MI 49087 www.chemlink.com

Distributed by: BEST MATERIALS ® Ph: 800-474-7570, 602-272-8128 www.BestMaterials.com Email: Sales@BestMaterials.com

Application Instructions M-1CR is a gun grade material that is applied from caulking guns, high viscosity pump guns, or automated bead application equipment. This product sets rapidly upon exposure to moisture. All application equipment must be clean and dry before using M-1CR. Open containers must be quickly protected from atmospheric moisture. Guns, pumps and hoses must be sealed when not in use.

• Mask off areas that must be protected from adhesives.

• Apply adhesive to one side of the assembly.

Do not use excessive adhesive. Beads can vary in size from 1/16 inch to 3/8 inch diameter for best application control.

• Compress beads firmly between substrates to set bonds. Presses and clamps are usually not required.

• Allow the assembly to cure for 30 minutes to an hour before handling or machining. When bonding two impermeable materials, brief separation and reassembly of the bonding surfaces to expose the adhesive to atmospheric moisture, will often accelerate the cure.

• In extremely dry environments, local humidification may be needed to initiate curing. Low temperature will retard the cure reaction and heat will accelerate the cure reaction. Optimum application is between 60°F to 100°F (16°C to 38°C).

Substrate Preparation Bonding surfaces must be clean, dry and free of oxidation, mill oils, wax, and release agents that may interfere with adhesion. Dry and fully cure painted surfaces before bonding. Alcohol and ammonia water are effective cleaners for surface preparation. Abraded or irregular surfaces are acceptable bonding surfaces but must be clean and sound. All substrates must be free of manufacturing defects.* *Test all substrates for bond strength and compatibility before application.

Typical Physical Properties

Viscosity 1,200,000 +/- 400,000 cp at 72°F (22°C)

Brookfield RVF, TF spindle, 4 RPM

Density 11.8 +/- 0.2 lbs per gallon ASTM D1475

Tack Free Time 20 +/- 10 min 45 +/- 5 % R.H.

Elongation at Break 275 - 325% ASTM D412

Tensil Strength 325 -375 psi ASTM D412

Hardness Shore A 38 - 42 ASTM C661

Low Temp.

Flex

-10°F (-23°C) 1/4 inch mandrel ASTM D816

Shrinkage No visible shrinkage after 14 Days

Service Temp. -40°F to 200°F / -40°C to 93°C

Results of Outgassed VOC Cleanroom Materials and Coatings Test VOC Type VOC in ppmw

(Parts Per Million Weight) Total VOC bp > 150°C 51 ppmw (µg/g)

Total VOC bp > 300°C 19 ppmw (µg/g)

Total VOC Compounds 52 ppmw (µg/g)

All properties described in this document are derived from testing conducted in laboratory conditions. Properties and performance will vary depending on environmental conditions and application technique. Test and evaluate to determine appropriate usage.

Visit www.chemlink.com for the Safety Data Sheet, Technical Data Guides and full warranty for this product.

LIMITED WARRANTY: Chem Link warrants this product’s performance, provided it is properly stored and applied within 1 year.

If this Chem Link material is proved to be defective, return remaining product and purchase receipt for refund or replacement of product exclusive of labor or cost of labor. This is the sole and exclusive remedy for defects or failure of this product. User must read and follow the direction of the current Technical Data Guide and SDS prior to product use. User determines suitability of product for intended use and assumes all risks. Manufacturer shall not be liable for damages (including consequential or incidental damages) in excess of the purchase price, except where such exclusion or limitation is prohibited by state law.

THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, WRITTEN OR ORAL, STATUTORY, EXPRESS OR IMPLIED INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE; except for the above express warranty given by manufacturer, the product is sold with all faults. Chem Link SHALL NOT BE RESPONSIBLE FOR THE USE OF THIS PRODUCT IN A MANNER TO INFRINGE ON ANY PATENT OR ANY OTHER INTELLECTUAL PROPERTY RIGHTS HELD BY OTHERS. This warranty gives you specific legal rights, and you may also have other rights in the U.S. which vary from state to state. For warranty claim information, call 800-826-1681.

Limitations

• Horizontal applications will require tooling.

• In areas where prolonged chemical exposure is anticipated, contact Technical Services for recommendations.

• Do not store in elevated temperatures.

• Remove all coatings and sealers before application.

• Please contact customer service for application guidelines with temperatures below 32°F (0°C).

• Test and evaluate all paints before application.

Product Specification Sheet APS733 - Rev. 08/2016

CC201 Clean Room Membrane Type Master StationsCC201 Clean Room Membrane Type Master Stations

42 Central Drive • Farmingdale • NY • 11735-1202 • Phone: (631) 777-5500 • Fax: (631) 777-559942 Central Drive • Farmingdale • NY • 11735-1202 • Phone: (631) 777-5500 • Fax: (631) 777-5599 TOLL-FREE: (800) 666-4800 • Web: AlphaCommunications.com • Email: info@alphacommunications.comTOLL-FREE: (800) 666-4800 • Web: AlphaCommunications.com • Email: info@alphacommunications.com

Copyright© 1998-2016 Alpha Communications® - All Rights Reserved.

Due to continuous product improvement, all colors, sizes, materials, finishes and specifications are subject to change without notice.

Architects' And Engineers'Architects' And Engineers' SpecificationsSpecifications

The Clean Room Master Station(s) shall be Alpha Communications® / Ring model CC201 or approved equivalent. Master(s) shall feature a protective antimicrobial membrane keypad, Talk and Cancel buttons and multi-color LED.

Master(s) shall be flush or surface wall mounted using the appropriate backbox / housing. Master(s) shall be used with the appropriate 3-gang flush electrical box (deep style) model BBF910 or BBS910 (surface back box).

Master(s) shall be designed to be used in hospital type (or other 'clean' room') environments, where easy cleaning and wipe-down sterilization is required. Contractor shall furnish and install the PSDC24-1.5 system power supply (or equivalent).

Contractor shall observe all local and national electrical and building codes.

CC201 Clean Room Membrane Type Master StationsCC201 Clean Room Membrane Type Master Stations

The CC201 is a simple one to one communication system designed to be used in a sterile environment. The antibacterial membrane inhibits the growth of bacteria, mold and mildew. It is resistant to chemicals and household cleaners and the station is designed to be water tight when used with a proper 3 gang electrical back box BBF910 (for flush mounting) or BBS910 surface back box.

The convenient 'simplex' operation allows the operator to push the TALK button when they need to talk and release to listen. When the conversation is over, either party can cancel the call by pressing the CANCEL button. The LED turns red when in the LISTEN mode and green in the TALK mode, so from a distance, one can see if the station is ON. There is a separate speaker and microphone for crystal clear intelligibility. The stations are designed for an optional headset and foot switch.

FeaturesFeatures

Antibacterial membrane keyboard Flush or Surface mounting (using appropriate housing) Convenient Simplex voice operation Multi-color LED for Talk/Listen Modes One to One operation Operates on 24VDC low-voltage Requires only 4 wires between the two stations Made in USA

SpecificationsSpecifications

Dimensions:

Width: 6.375" (162mm) Height: 4.475" (114mm) Depth: 3.00" (77mm)

Operating Voltage: 20-27VDC

Power Consumption: 150mA max.

Flush Backbox: Standard (deep style) 3-gang electrical back box model BBF910

Surface Backbox: BBS910

/part/CC201 /part/BBF910 /part/BBS910 /part/PSDC24-1.5 /part/CC201 /part/BBF910 /part/BBS910 /part/BBF910 /part/BBS910

Product Submittal Sheet Tech Support: 888-437-3244 Sales: 800-543-7140

Engineering Services: 877-832-3206 clarkdietrich.com

Barrier Mesh™ for Security (BM75) High-strength expanded metal mesh for walls and ceilings

Barrier Mesh™ is a tough, rigid, heavy-gauge steel mesh installed typically onto stud framing (both metal and wood), with gypsum sheathing applied to its surface to conceal the barrier mesh, thereby providing a significant barrier to security breach across that wall system.ClarkDietrich Building Systems’ Barrier Mesh™ (BM) can also be used without sheathing to provide an enhanced protection of security to walls, ceilings as well as floors. Barrier Mesh™ is produced in different size diamonds and gauges for minimum, medium or maximum security protection.

In addition to providing high-strength and fire-resistant protection, Barrier Mesh™ also offers a cost effective and time-saving alternative to reinforced concrete or concrete masonry systems.

The Barrier Mesh™ System is designed to attach to metal or wood stud framing, with specially designed Barrier Mesh™ clips, purchased with the Barrier Mesh and shipped together, as a system. ClarkDietrich mesh sheets are 4’x 8’ and sizes in chart below; special order mesh sizes available upon requests with additional lead-time.

Projects uses:

Correctional facilities, government offices, retail stores, computer rooms, airport security, law enforcement facilities, military facilities or any space that requires substantial barrier protection.

Product Data & Ordering Information:

Material: Type ll, Class 1 - Carbon Steel - Mesh, Complying to ASTM F1267 & A1011 (Type ll, Class 2 - Galvanized available by special order) Expanded Metals Manufacturers Association - EMMA 557-15 Sheet Size: 48" x 96" (Tolerance -0, +1/4" / foot of dimension, length & width

Product Nom. Overall Bond Size Weight % Of Code Gauge Thickness Diamond Center-to-Center lbs/100 sq ft Open Area BM75 16 .048" 3/4" .923" x 2.10" 47 76 BM75 13 .072" 3/4" .923" x 2.10" 67 77 BM75 9 .108" 3/4" .923" x 2.10" 157 65

ASTM & Code Standards:

• ASTM F1267 - Standard Specification for Metal, Expanded, Steel ( Type ll, Class 1 - Carbon

Steel, Type ll, Class 2 - Galvanized, Type ll, Class 3 - Stainless Steel)

• ASTM A1011/A1011M - Standard Specification for Steel Sheet, Hot-Rolled, High-Strength

Low-Alloy Carbon

• SDS & Product Certification Information is available at www.clarkdietrich.com/SupportDocs

Storage:

All stored materials shall be kept dry. Materials shall be stacked off the ground, supported on a level platform, and protected from the weather and surface contamination.

09.22.36 (Metal Lath)

• Protects against break-ins and break-outs on metal stud framing

• Ideal for use in lieu of reinforced concrete or concrete block

• High-strength and fire-resistant

• Made from carbon steel

Sustainability Credits:

For more details and LEED letters contact Technical Services at 888-437-3244 or visit www.clarkdietrich.com/LEED LEED v4 MR Credit -- Building Product Disclosure and Optimization: EPD (1 point) - Sourcing of Raw Materials (1 point) - Material Ingredients (1 point) - Construction and Demolition Waste Management (up to 2 points) - Innovation Credit (up to 2 points).

LEED 2009 Credit MR 2 & MR 4 -- ClarkDietrich's steel products are 100% recyclable and have a national average recycled content of 34.2% (19.8% post-consumer and 14.4% pre-consumer). If seeking a higher number to meet Credit MR 5, please contact us at (info@clarkdietrich.com / 888-437-3244)

Project Information Contractor Information Architect Information Name: Name: Name:

Address: Contact: Contact:

Phone: Phone:

Fax: Fax:

BM75 © 11/2018 ClarkDietrich Building Systems https://www.clarkdietrich.com/LEED mailto:info@clarkdietrich.com

Pe | Package Passer

Features

Product descriPtion The PE package passer consists of a rectangular box built from transparent bullet resistant glazing material, with doors on the customer and employee sides. A mechanical interlocking mechanism prevents the opening of both doors simultaneously, allowing small packages to be passed through a barrier without a breach of security. The PE is designed for moderate to frequent use, long service life, low cost, and little or no maintenance.

For applications requiring the passage of large to very large packages, people, or equipment, contact our sales/ engineering department for more information.

available sizes Typical Standard Size:

Box OD 14” W x 14” H x 14” D

Typical Large Size:

Box OD 16” W x 14” H x 14” D

Custom sizes manufactured based on maximum package dimensions. Consult factory for unit sizing. Please contact our sales/engineering department for current pricing & delivery information.

bullet resisting glazing Bullet Resistant Level 1 1 1/4” Uncoated Acrylic

1 1/4” AR Coated Acrylic

Bullet Resistant Level 2 1 3/8” AR Coated Acrylic

Bullet Resistant Level 3 1 1/4” LP 1250 Laminated sPeciFications

A. CONSTRUCTION

1. PE Package Passer constructed from bullet resisting transparent acrylic or polycarbonate material in box shape.

2. Package Passer to have hinged doors controlled by mechanical interlocking mechanism.

3. Mechanical interlocking mechanism to allow only one door to be opened at a time, preventing breach in security.

4. Standard base is particle board with black plastic laminate covering.

5. Unit assembled using 1/4-20 steel machine screws.

B. GLAZING

1. Glazing materials shall be of a type listed by

Underwriter’s Laboratories Standard 752 for bullet resistance and/or tested by H.P. White Laboratory for specified bullet resistance.

2. Bullet resisting protection level shall be as specified by end user and consistent with threat level.

markets served

1.517.223.7807

170 National Park Drive | Fowlerville, MI 48836 www.TotalSecuritySolutionsInc.com

Handling inFormation Handling: Care should be exercised during shipping and handling to maintain package passer appearance.

Storage: Store upright in a dry, well ventilated building or shelter at a constant temperature. Do not store in damp areas or freshly plastered buildings. Place unit on wood blocks at least 2” high to prevent moisture damage.

Application: Remove from protective container just prior to installation. Care should be exercised when installing window to insure that installation is level, plumb, square and secure.

Cleaning: You must clean the glazing unit during and after the construction period to maintain optimum performance and aesthetic properties. To clean, use a soft, clean cloth and a mild soap, detergent, or slightly acidic cleaning solution (such as vinegar). Wipe with a clean, lint-free cloth.

tecHnical suPPort TSS maintains a full staff of professional and experienced sales representatives, project estimators, engineers, draftsmen, craftsmen and installers ready to assist in all phases of the bullet resistant project from initial design through installation. Consult our sales department or your local representative for assistance with all your bullet-resistant needs at 1.517.223.7807.

limited WarrantY TSS offers a twelve month limited warranty. This warranty does not cover damage caused by neglect, abuse, vandalism, improper maintenance, accident or any other cause beyond the suppliers control not arising out of defects in material or workmanship. The warranties stated replace and exclude all other warranties. The warranty is limited to replacing products that fail to meet specification, or are defective in quality or workmanship at the time of delivery. TSS will not be responsible for (re)installation expenses or any direct or indirect loss(es) which may result from a defective product. TSS reserves the right to field inspect any product alleged to be defective. The buyer is responsible for any consequences resulting from product use.

1.517.223.7807

170 National Park Drive | Fowlerville, MI 48836 www.TotalSecuritySolutionsInc.com

PE

THREAT SIDE

SECURE SIDE

A

D E

T A

I L

S T o t a l

S e c u r i t y

S o l u t i o n s

N a t i o n a l

P a r k

D r i v e

F o w l e r v i l l e

M

I

P h o n e

F a x

T h e i n f o r m a t i o n i n h i s d r a w i n g i s c o n f i d e n t i a l

I i s t h e e x c l u s i v e p r o p e r t y o f

T

O T

A L

E C

U R

I T

Y

S O

L U

T I O

N S

W r i t t e n p e r m i s s i o n i s r e q u i r e d f o r r e p r o d u c t i o n a n d o r d i s t r i b u t i o n f r o m

T

O T

A L

S E

C U

R I T

Y

S

O L

U T

I O

N S w w w D e m a n d T

S S c o m

T O

T A

L

S E

C U

R I T

Y

S O

L U

T I O

N S

1 2 3

D

A T

E D

E S

C R

I P

T I O

N

D R

A W

N

B

Y

E N

G

B

Y

C H

E C

K E

D

B

Y

D A

T E

P R

O J E

C T

N

A M

E

J O

B

S H

E E

T

N

U M

B E

R

R E

V I S

I O

N S

S H

E E

T

T

I T

L E

X

P

A C

K A

G

C

H A

N G

E R

B D

J

S A

L

PRODUCT SPECIFICATION SECTION 13070

170 National Park Drive, Fowlerville, MI 48836 800-513-1468 www.tssbulletproof.com 02/27/2018

TSS PE ACRYLIC PACKAGE PASSER

PART 1 GENERAL

1.1 REFERENCE

A. Underwriters Laboratory UL 752-Standard for Bullet Resisting Equipment & ASTM E119-98- Standard Test Methods for Fire Tests of Building Construction and Materials, NIJ Standard 0108.01-(National Institute of Justice) Standard for Ballistic Resistant Protective Materials, ASTM B 209/B 209M- Standard Specification for Aluminum and Aluminum Alloy Sheet and Plate, ASTM A 666-Standard Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate and Flat Bar..

1.2 SUBMITTALS

A. The following shall be submitted by the manufacturer in accordance with Sections 13070 and any Special Contract

Requirements and coordinate with Sections 01340: Submit for approval prior to fabrication: samples, product data (including preparation, storage and installation methods), cuts & anchor spacing, reinforcement & location , product specifications, shop drawings, test reports (current UL Listing Verification & UL 752 Test Results as provided by Underwriters Laboratories), and printed data in sufficient detail to indicate compliance with the contract documents.

B. Manufacturer’s Instructions for installation and cleaning. All required submittals shall be approved prior to installation.

1.3 DESIGN PERFORMANCE

A. Through the design, manufacturing techniques and material application the TSS PE Acrylic Package Passer shall be constructed of acrylic with a UL Standard 752 Level 1, 2 or 3 rating. This assembly shall provide single or multiple transaction positions utilizing the rectangular acrylic box. The mechanical interlocking mechanism shall prevent the doors from being opened simultaneously, allowing packages to be passed through a barrier without a breach of security. Anchor screws shall be provided by the installer.

B. No field alterations to the construction of the units fabricated under the acceptable standards shall be allowed unless approved by the manufacturer and the architect. Standard manufacturing tolerances shall be +/- 1/16".

C. Materials shall meet or exceed UL 752 requirements.

1.4 QUALITY ASSURANCE

A. Manufacturer shall be a Company that specializes in manufacturing products of the specified type with a minimum of five years experience. Installer shall be a Company that specializes in product type specified and Certified for the installation by the manufacturer. Manufacturer shall provide a Mock-up, if required, for evaluation of surface preparation and application workmanship and color/finish to the Architect for approval prior to start of work.

1.5 DELIVERY, STORAGE & HANDLING

A. Delivery the materials to the project. Handle the materials with care to prevent damage. Store materials inside and under cover, stack flat and off floor. Project conditions (temperature, humidity, and ventilation) shall be within the maximum limit recommendations set by manufacturer. Do not install products that are under conditions outside these limits.

1.6 WARRANTY

A. All materials shall be warranted against defects for a period of 1 year for the date of receipt at the project site. .

Certificates of manufacturer’s standard limited warranty shall be provided at project completion.

http://www.tssbulletproof.com/

PART 2 PRODUCTS

2.1 ACCEPTABLE MANUFACTURERS

A. A. Products shall be manufactured by: Total Security Solutions, Inc, 170 National Park Drive, Fowlerville, MI 48836, 800- 513-1468. Attn: Sales Department, info@tssbulletproof.com. Web: www.tssbulletproof.com. No substitutions shall be accepted.

2.2 BULLET RESISTANT ACRYLIC PACKAGE PASSER

A. Product shall be: TSS PE Acrylic Package Passer (interlocking): The PE package passer consists of a rectangular box built from transparent bullet resistant glazing material, with doors on the customer and employee sides. A mechanical interlocking mechanism hinged door control, prevents the opening of both doors simultaneously, allowing small packages to be passed through a barrier without a breach of security. Standard base is particle board with black plastic laminate covering, using ¼-20 steel machine screws.

Option is available for applications requiring the passage of large to very large packages, equipment or information.

B. Product size shall be: TSS PE Acrylic Package Passer

1) Size shall be _______ (specify below or custom size)

Sizes: OD 14”W x 14” H x 14” D, OD 16”W x 16” H x 16” D, OD 24”W x 24” H x 24” D

C. Security Level shall be: ___________________ (specify one)

Bullet Resistant Level 1 1 1/4" Uncoated Acrylic

Bullet Resistant Level 2 1 3/8" Uncoated Acrylic

Bullet Resistant Level 3 1 1/4" LP 1250 Laminated

PART 3 EXECUTION

3.1 PREPARATION

A. Prior to installing the bullet resistive material, the contractor shall verify that all supports have been installed as required by the contract documents and architectural drawings, and approved shop/CAD drawings, if required. Installer shall notify architect of any unsatisfactory preparation that is responsibility of another installer.

B. Clean and prepare all surfaces per manufacturers recommendations for achieving the best results for the substrate under the project conditions.

3.2 INSTALLATION

A. Do not begin installation until openings have been verified and surfaces properly prepared in accordance with Drawings.

Install in accordance with manufacturer’s instructions and UL 752. Set all equipment plumb. All product shall be installed per installation instructions provided by Total Security Solutions, if warranty is to be issued.

B. TSS PE Acrylic Package Passer (interlocking) shall arrive on site as a completed unit. Unit shall be installed in provided opening (wall/door), secured to structure (anchors by others).

3.3 POST APPLICATION

A. TSS PE Acrylic Package Passer shall be installed in accordance with manufacturer’s printed recommendations, including adhering to anchoring and finishing details.

B. Inspection and Cleaning: Verify installation is complete and complies with manufacturer’s requirements. Clean product and accessories, removing excess sealant, labels and protective covers.

C. Touch-up, repair or replace damaged products before Substantial Completion.

D. Product Warranty: Applicable warranty shall be issued to owner upon final release of completed project.

**end of section**

TAC® offers three access control modules to meet the demands of different access requirements:

AC-1:

Use the AC-1 when powering modules from a Andover Continuum power supply. (AC-1 has a 24VDC power input only. ) The AC-1 supports Wiegand/Prox cards and 5 V/12 V reader power (switch-selectable).

AC-1A:

Use the AC-1A if you are powering modules from a local 12VDC power supply. The AC-1A offers an extended 10-28VDC power input. (Power supply can also power any 12 V prox readers you may be using.) The AC-1A supports Wiegand/Prox cards, and 5 V reader power only.

AC-1PLUS:

The enhanced version. Use the AC-1Plus when using mag stripe or Cardkey readers, ADA sequences that require extra inputs, special door unlock/door ajar times for disabled persons, and jobs that require reader tamper detection. The AC-1Plus offers an extended 10-28VDC power input (power supply can also power 12 V prox readers), and supports 5 V reader power only.

AC-1 Family Family of Access Control Modules

SDS-C-IOMODULES-US.BU.N.EN.6.2006.0.00.CC

Schneider Electric One High Street, North Andover, MA 01845 USA Telephone: +1 978 975 9600 Fax: +1 978 975 9674 www.schneider-electric.com/buildings

AC-1

I/O Module The AC-1provides full I/O for an access controlled door or portal in one compact module. The AC-1 can be located near an access controlled door for localized control and reduced wiring costs; or several AC-1 modules can be grouped together and DIN rail-mounted for centralized control.

The AC-1 provides a Wiegand card input for Wiegand swipe and proximity type cards, reading up to 64 bits per card. Reader power is switch-selectable between 5V and 12V to meet most card reader power requirements.

The AC-1 has two 5 A, Form C relays—one for the door lock and a second for local alarm annunciation. Each output has an integral hand-off-auto switch for manual operation, and software feedback of the switch position.

Up to three supervised alarm inputs can be used for door status contacts, request-to-exit devices, a cabinet tamper switch, or any other two-state or three-state (on/off/trouble) alarm device.

Keypad Control The AC-1 supports Wiegand output keypads. To simplify installation and reduce wiring costs, the keypad data comes into the module via the reader data lines.

Access Control During normal operation of the AC-1, access decisions are made in the Andover Continuum NetController CPU , which provides storage for up to 75,000 “local” personnel records. In addition, the NetController’s event buffer is software-configurable to allow for the most optimized memory usage.

If network communications are interrupted, the AC-1 will revert to a programmable degrade mode of operation, providing uninterrupted card access using site codes and other degrade mode parameters stored in non-volatile EEPROM in each AC-1 module.

A door can be configured to operate based on site code only, site code plus card, card plus personal ID number (PIN), or keypad only. The door’s operating mode can even be changed based on time-of-day or other events for optimum flexibility through TAC’s easy-to-use Andover Plain English programming language. Each keypad can also permit entry of a duress alarm code that can initiate an alarm sequence at any AC-1 controller or at the Andover Continuum workstation.

Time-based anti-passback and entry/egress anti-passback are available to prevent tailgating. Entry/ egress anti-passback is system-wide and can be performed by readers located on different AC-1 controllers across the network.

Using Andover Plain English, the AC-1 can also be used for custom access control sequences such as two-man rule, optical turnstile control, and man trap configurations.

AC-1

Electrical

Power Consumption

2.6 W plus reader power consumption

at 24VDC max.

Overload Protection

0.5 A resettable fuse with transient

voltage suppressor (TVS) and reverse polarity protection

Inputs

Card Readers

Card Reader Type

Supports Wiegand swipe and proximity readers

Maximum Number of bits/Card

Card Reader Power

5 VDC or 12 VDC (switch selectable)

Switch Setting: +5 V

Output Voltage: +5.20 V ±0.05 V

Output Current: 120 mA (max.)

Switch Setting: +12 V

Output Voltage: +12.0 V ±5%

Output Current: 180 mA (max.)

Distance, Card Reader to AC-1

500 ft. max. using 18-ga. wire

200 ft. max. using 22-ga. wire

Alarm Inputs

Up to 3 supervised inputs. Single or double resistor supervision, series or parallel

Input Protection

Transient voltage suppressor (TVS) on each input

Outputs

Door Outputs

2 Form C relays

Output Rating

5 A @ 24 V AC/DC

Output Protection

5,000 V isolation

270 V metal oxide varistors (MOVs) on each output

Overrides

3-position manual override switch on each output for manual control of relay.

LED override status indicator

Override Feedback

Override detection and software feedback provided for each output

Reader LED Output

Open collector; up to 50 mA

Inputs/Output Connections

Two-piece, 16-position removable terminal block

User LEDs/Switches

Status Indicator LEDs

Power Power Indicator

Comm TD Indicator

Override Common Override

Indicator

Status Service/Wink Indicator

Out1 - Out2 Two Output

Status Indicators

+5 V Reader Power 5 V Reader

Power Indicator

+12 V Reader Power 12 V Reader

Power Indicator

Switches

Commission

Reset

AC-1

Specifications

SDS-C-IOMODULES-US.BU.N.EN.6.2006.0.00.CC

Schneider Electric One High Street, North Andover, MA 01845 USA Telephone: +1 978 975 9600 Fax: +1 978 975 9674 www.schneider-electric.com/buildings

PHYSICAL ACCESS SOLUTIONS

HID Global’s iCLASS SE® platform goes beyond the traditional smart card model to offer a secure, standards-based and flexible platform that has become the new benchmark for highly adaptable, interoperable and secure access control solutions.

Ideal for new and existing installations, iCLASS SE readers provide customers the assurance that their existing investments can be leveraged to enhance their system as business requirements change. The technology-independent readers also support iCLASS Seos and iCLASS SE credential platforms, as well as standard iCLASS, MIFARE and MIFARE DESFire EV1 supporting custom data models.

Additionally, iCLASS SE readers support mobile devices utilizing Seos, enabling a new class of portable identity credentials that can be securely provisioned and safely embedded into both fixed and mobile devices.

As part of HID Global’s iCLASS SE platform that is based on the Secure Identity Object™ (SIO®) data model and Trusted Identity Platform® (TIP™), the powerfully secure iCLASS SE readers offer advanced features such as layered security beyond the card media and tamper-proof protection of keys/cryptographic operations using EAL5+ secure element hardware.

hidglobal.com iCLASS SE® Readers

HIGHLY ADAPTABLE AND SECURE HIGH FREQUENCY

ACCESS CONTROL SOLUTION

� Powerfully Secure – Provides layered security beyond the card media for added protection to identity data using SIOs.

� Adaptable – Interoperable with a growing range of technologies (iCLASS® Seos™ and iCLASS SE® credential platforms, standard iCLASS®, MIFARE®, and MIFARE DESFire® EV1 with custom data models) and form factors including mobile devices utilizing Seos™.

� Interoperable – Open Supervised Device Protocol (OSDP) for secure, bidirectional communication.

POWERFULLY SECURE:

� Multi-Layered Security – Ensures data authenticity and privacy through the multi-layered security of HID’s SIO.

� EAL5+ Certified Secure Element Hardware – Provides tamper-proof protection of keys/cryptographic operations.

� Secured communications using OSDP with Secure Channel Protocol.

� Expanded iCLASS Elite™ Program – Extends private security by protecting uniquely keyed credentials, SIOs and programming keys.

HIGHLY ADAPTABLE:

� Mobile device support using iCLASS Seos - enabling HID access control.

� Flexible to support future technologies.

� Field Programmable Readers – Provides secure upgrades for migration and extended lifecycle.

iCLASS SE readers include Open Supervised Device Protocol (OSDP), a new Security Industry Association (SIA) standard that together with Secure Channel Protocol (SCP) provides secure communications and central management.

SUSTAINABILITY AND MANAGEMENT:

� Intelligent Power Management (IPM) – Reduces reader power consumption by as much as 75% compared to standard operating mode.

� Recycled Content – Contributes toward building LEED credits.

INTEROPERABLE:

� SIO Media Mapping – Simplifies deployment of third-party objects to multiple types of credentials.

� Industry standard communications using OSDP.

� Custom programming support to read models on MIFARE and MIFARE

DESFire EV1 credentials http://www.hidglobal.com

* Typical read range achieved in air. Different types of metal will cause some degradation (typically up to 20%).

Use spacers to space product off metal and improve read range if required.

** NSC = Normal Standby Current; See Installation Guide for Details *** Measured in accordance with UL294 standards; See Installation Guide for Details

SPECIFICATIONS

© 2012-2014 HID Global Corporation. All rights reserved. HID, the HID logo, iCLASS SE, Seos, iCLASS, Secure Identity Object, SIO, Trusted identity Platform, TIP and iCLASS Elite are trademarks or registered trademarks of HID Global in the U.S. and/or other countries. All other trademarks, service marks, and product or service names are trademarks or registered trademarks of their respective owners.

2014-04-15-hid-iclass-se-readers-ds-en PLT-00230

Model Name R10 R15 R30 R40 RK40 Base Part Number 900N 910N 930N 920N 921N

Typical Read Range* (inches)

13.56 MHz Single Technology ID-1 Cards – SIO Data Model

iCLASS SE®: 3" (7.6 cm) SE for DESFire® EV1: 2"

(5.1 cm) SE for MIFARE® Classic:

2.3" (5.8 cm) iCLASS SE: 3" (7.6 cm) SE for DESFire EV1: 2"

(5.1 cm) SE for MIFARE Classic:

2.3" (5.8 cm) iCLASS SE: 3.5" (8.9 cm) SE for DESFire EV1: 2"

(5.1 cm) SE for MIFARE Classic:

3" (7.6 cm) iCLASS SE: 4.5" (11.4 cm) SE for DESFire EV1: 3.3"

(8.4 cm) SE for MIFARE Classic:

3.5" (8.9 cm) iCLASS SE: 5" (12.7 cm) SE for DESFire EV1: 2.3"

(5.8 cm) SE for MIFARE Classic:

4.5" (11.4 cm)

13.56 MHzSingle Technology Tags/Fobs – SIO data Model

iCLASS SE: 1.3" (3.3 cm) SE for MIFARE Classic:

0.5" (1.3 cm) iCLASS SE: 1.3" (1.3 cm) SE for MIFARE Classic:

0.5" (1.3 cm) iCLASS SE: 2" (5.1 cm) SE for MIFARE Classic:

1.5" (3.8 cm) iCLASS SE: 1.8" (4.6 cm) SE for MIFARE Classic:

1.5" (3.8 cm) iCLASS SE: 1.8" (4.6 cm) SE for MIFARE Classic:

1.5" (3.8 cm)

Mounting

Mini-Mullion Size;

physically HID's smallest iCLASS® readers and are ideally suited for mullion-mounted door installations, U.S. single-gang J-box (with mud ring) or any flat surface

Mullion Size; physically HID's second smallest iCLASS readers and are ideally suited for mullion-mounted door installations, U.S. single-gang J-box (with mud ring) or any flat surface

EU / APAC Square Size;

83.8 mm (3.3”) square reader is designed to mount to and cover standard European and Asian back boxes

Wall Switch Size; designed to mount and cover single gang switch boxes primarily used in the

Americas and includes a slotted mounting plate for European and Asian back box spacing

Color Black or Gray

Keypad No Yes (4x3)

Dimensions 1.9" x 4.1" x 0.9"

4.8 cm x 10.3 cm x 2.3 cm

1.9" x 6.0" x 0.9"

4.8 cm x 15.3 cm x 2.3 cm

3.3" x 3.3" x 0.9"

8.4 cm x 8.4 cm x 2.3 cm

3.3" x 4.8" x 1.0"

8.4 cm x 12.2 cm x 2.4 cm

3.3" x 4.8" x 1.1"

8.5 cm x 12.2 cm x 2.8 cm

Product Weight (Pigtail) 3.9 oz (113g) 5.3 oz (151g) 5.2 oz (148g) 7.7 oz (220g) 9.0 oz (256g)

Product Weight (Terminal Strip) 2.9 oz (84g) 4.2 oz (120g) 4.0 oz (116g) 7.5 oz (215g) 8.0oz (226g)

Operating Voltage Range 5-16 VDC, Linear supply recommended

Current Draw - Standard Power Mode*** (mA) 60 60 65 65 85

Current Draw - Intelligent Power Management (IPM) Mode*** (mA) 35 35 40 40 60

Peak Current Draw - Standard Power or IPM Mode*** (mA) 200 200 200 200 220

NSC** Power Consumption - Standard Power Mode (W @ 16VDC) 1.0 1.0 1.0 1.0 1.4

NSC** Power Consumption - w/ IPM (W

@ 16VDC) 0.6 0.6 0.6 0.6 1

Operating Temperature -31º to 150º F (-35º to 65º C)

Storage Temperature -67º to 185º F (-55º to 85º C)

Operating Humidity 5% to 95% relative humidity non-condensing

Environmental Rating Indoor/Outdoor IP55; IP65 if installed with optional gasket (IP65GSKT)

Transmit Frequency 13.56 MHz

13.56 MHz Card Compatibility

Secure Identity Object™ (SIO) on iCLASS Seos, iCLASS SE/SR, MIFARE DESFire EV1 and MIFARE Classic (On by Default)

- MIFARE and MIFARE DESFire EV1 custom data models

- standard iCLASS Access Control Application (order with Standard interpreter)

-ISO14443A (MIFARE) CSN, ISO14443B CSN, ISO15693 CSN

- FIPS-201 Credentials including PIV, PIV-I, CIV, CAC, TWIC, FRAC; Contactless Interface

Communications Optional OSDP with SCP over RS485 Wiegand/Clock-and-Data Interface 500ft (150m) (22AWG) - Use Shielded cable for best results

Panel Connection Pigtail or Terminal Strip

Certifications UL294/cUL (US), FCC Certification (US), IC (Canada), CE (EU), C-tick (Australia, New Zealand), SRRC (China), MIC (Korea), NCC (Taiwan), iDA (Singapore), RoHS, FIPS-201 Transparent FASC-N Reader

Cryto Processor Hardware Common Criteria Rating EAL5+

Patents US7124943, US6058481, US6337619

Housing Material UL94 Polycarbonate

Manufactured with % of recycled content (Pigtail) 10.5% 11.0% 11.0% 10.5% 10.9%

Manufactured with % of recycled content (Terminal Strip) 11.0% 11.5% 10.5% 11.0% 12.4%

UL Ref Number R10E R15E R30E R40E RK40E

Warranty Limited Lifetime

An ASSA ABLOY Group brand

North America: +1 949 732 2000 Toll Free: 1 800 237 7769 Europe, Middle East, Africa: +44 1440 714 850 Asia Pacific: +852 3160 9800 Latin America: +52 55 5081 1650 hidglobal.com http://fargo.hidglobal.com VHAHOUDiazA4 Rectangle

Intrusion Systems | DS160 Series High Performance Request‑to‑exit Detectors

The DS160 Series consists of the DS160 Detector (light gray) and the DS161 Detector (black) specifically designed for Request-to-exit (REX) applications. With features such as timers, door monitor with sounder alert, and pointable coverage, the DS160 and DS161 have the flexibility to meet the most stringent REX requirements.

The exclusive Sequential Logic Input (SLI) provides added security that is not offered in any other REX device.

Functions

Sequential Logic Input (SLI) The SLI terminal allows connection of a second device to require sequential detection. This eliminates the possibility that an object that is slid through the door or underneath the door will activate the detector. This input can also be used to lock the sensor if motion is present outside the premises.

Door Monitor The sensor can monitor a door contact to allow special control of the internal relay. For example, if the door is opened within the relay time period, the sensor can be programmed to halt the timer. If the door is not opened within a specific time period, the relay can be programmed to deactivate.

Sounder Alert An integrated sounder can be programmed to activate if the door is left open too long. The sounder volume is fully adjustable to 85 dB.

Keycard Input The keycard input allows the sensor relay to be controlled from an external source, such as an access control system or card reader.

DS160 Series High Performance Request‑to‑exit Detectors

▶ Door monitor with sounder alert

▶ Sequential Logic Input (SLI)

▶ Internal vertical pointability

▶ Wrap-around coverage pattern with precise pattern control

▶ Up to 64 second adjustable latch time

▶ Selectable relay trigger mode

▶ Selectable fail-safe or fail-secure modes

▶ Adjustable sounder volume

▶ Activation LED www.boschsecurity.com

2 | DS160 Series High Performance Request‑to‑exit Detectors

Certifications and Approvals

Region Certification

Europe CE 89/336/EEC, EN55022: 1998 +A1:

2000 +A2: 2003, EN50130-4: 1996

+A1: 1998 +A2: 2003, EN61000-4-2:

1995 +A1: 1998 +A2: 2001, EN61000-4-3: 2002 +A1: 2003,

EN61000-4-4: 1995 +A1: 2000 +A2:

2001, EN61000-4-5: 1995 +A1: 2001,

EN61000-4-6: 1996 +A1: 2001 +A2:

2001, EN61000-4-11:1994 +A1: 2001,

EN60950-1: 2001

2004/108/EC; EN 50130-4:1996

+A1:1998 +A2:2003; EN

60950-1:2006

USA UL ALVY: Access Control Systems Units

(UL294)

Europe Complies with EN50131‑1 Grade 2

Installation/Configuration Notes

ALARM WILL

SOUND WHEN

DOOR IS

OPENED

3 m (10 ft)

ALARM WILL

SOUND WHEN

DOOR IS

OPENED

1.2 m (4 ft)

Front View Mounted on wall above door and mounted on ceiling .75 m (2.5 ft) in front of the door.

1.5 m (5 ft)

3 m

(10 ft)

Side View The higher that you mount the unit, the larger the coverage area. Do not mount the DS160/DS161 more than

4.6 m (15 ft) above the floor.

Side view of coverage pattern with the unit mounted at

4.6 m (15 ft) above the floor with…