24RWP03_SOL.pdf

CODE

(Hour)

PAGE(S)

until 04:00 PM local time 28 May 2024

X

A X B X C X D

EX

X

G F 86 - 96

97 - 112 X H 113 - 118 susan.k.eckerle.civ@us.navy.mil

RATING PAGE OF PAGES

7. ISSUED BY

(Date)

IMPORTANT - Award will be made on this Form, or on Standard Form 26, or by other authorized official written notice.

Previous Edition is Unusable 33-134 STANDARD FORM 33 (REV. 9-97)

Prescribed by GSA FAR (48 CFR) 53.214(c)

DO-A7 1 118

(If other than Item 7)

15A. NAME 16. NAME AND TITLE OF PERSON AUTHORIZED TO

AND

ADDRESS

SIGN OFFER (Type or print)

OF

OFFEROR

AMENDMENT NO. DATE

15B. TELEPHONE NO (Include area code) 17. SIGNATURE15C. CHECK IF REMITTANCE ADDRESS

IS DIFFERENT FROM ABOVE - ENTER

SUCH ADDRESS IN SCHEDULE.

18. OFFER DATE

1. THIS CONTRACT IS A RATED ORDER

UNDER DPAS (15 CFR 700)

2. CONTRACT NO.

N00164 8. ADDRESS OFFER TO

See Item 7

9. Sealed offers in original and 0 copies for furnishing the supplies or services in the Schedule will be received at the place specified in Item 8, or if handcarried, in the depository located in

CAUTION - LATE Submissions, Modifications, and Withdrawals: See Section L, Provision No. 52.214-7 or 52.215-1. All offers are subject to all terms and

(See Section L) conditions contained in this solicitation.

10. FOR INFORMATION

CALL:

A. NAME (NO COLLECT CALLS)

SUSAN ECKERLE (812) 854-6538

11. TABLE OF CONTENTS

SOLICITATION/ CONTRACT FORM

SUPPLIES OR SERVICES AND PRICES/ COSTS

2 - 17

X I CONTRACT CLAUSES

DESCRIPTION/ SPECS./ WORK STATEMENT X

PACKAGING AND MARKING

18 - 40 41 - 43

J LIST OF ATTACHMENTS

INSPECTION AND ACCEPTANCE

DELIVERIES OR PERFORMANCE

44 - 47 48 - 51

X K

REPRESENTATIONS, CERTIFICATIONS AND

OTHER STATEMENTS OF OFFERORS

CONTRACT ADMINISTRATION DATA 52 - 60 X

SPECIAL CONTRACT REQUIREMENTS

OFFER (Must be fully completed by offeror) 61 - 63 X M

L INSTRS., CONDS., AND NOTICES TO OFFERORS

EVALUATION FACTORS FOR AWARD

NOTE: Item 12 does not apply if the solicitation includes the provisions at 52.214-16, Minimum Bid Acceptance Period.

is inserted by the offeror) from the date for receipt of offers specified above, to furnish any or all items upon which prices are offered at the price set opposite each item, delivered at the designated point(s), within the time specified in the schedule.

13. DISCOUNT FOR PROMPT PAYMENT

(See Section I, Clause No. 52.232-8)

14. ACKNOWLEDGMENT OF AMENDMENTS

(The offeror acknowledges receipt of amendments

AMENDMENT NO. DATE

to the SOLICITATION for offerors and related documents numbered and dated):

FACILITY

12. In compliance with the above, the undersigned agrees, if this offer is accepted within calendar days (60 calendar days unless a different period

SOLICITATION, OFFER AND AWARD

X

(X) SEC. DESCRIPTION (X) SEC. DESCRIPTION PAGE(S)

PART I - THE SCHEDULE

26. NAME OF CONTRACTING OFFICER (Type or print) 27. UNITED STATES OF AMERICA 28. AWARD DATE

EMAIL:TEL: (Signature of Contracting Officer)

CODE CODE

B. TELEPHONE (Include area code) C. E-MAIL ADDRESS

AWARD (To be completed by Government)

19. ACCEPTED AS TO ITEMS NUMBERED 20. AMOUNT 21. ACCOUNTING AND APPROPRIATION

22. AUTHORITY FOR USING OTHER THAN FULL AND OPEN COMPETITION:

10 U.S.C. 2304(c)( ) 41 U.S.C. 253(c)( ) (4 copies unless otherwise specified)

23. SUBMIT INVOICES TO ADDRESS SHOWN IN ITEM

24. ADMINISTERED BY (If other than Item 7) CODE 25. PAYMENT WILL BE MADE BY CODE

PART IV - REPRESENTATIONS AND INSTRUCTIONS

PART III - LIST OF DOCUMENTS, EXHIBITS AND OTHER ATTACHMENTS

64 - 82

PART II - CONTRACT CLAUSES

NAVAL SURFACE WARFARE CENTER CRANE DIV

S. ECKERLE (812-854-6538)

BLDG 121

300 HWY 361

CRANE IN 47522-5001

812-854-6538

FAX:

TEL:

FAX:

TEL:

NOTE: In sealed bid solicitations "offer" and "offeror" mean "bid" and "bidder".

SOLICITATION

83 - 85

6. REQUISITION/PURCHASE NO.5. DATE ISSUED

11 Apr 2024

4. TYPE OF SOLICITATION

SEALED BID (IFB)

NEGOTIATED (RFP)

[ X ]

3. SOLICITATION NO.

N0016424RWP03

Section B - Supplies or Services and Prices

ITEM NO SUPPLIES/SERVICES MAX QTY U/I UNIT PRICE MAX AMOUNT

0001 First Article Evaluation and

Overhaul

3 Each

First Article Requirement for the MK-82 Director DC Motor (P/N 2907650) Evaluation and Overhaul IAW the SOW, Section 3.2 and all applicable documents.

First Article Evaluation and Overhaul will be waived by the Government if the offeror has overhauled the item within the last five (5) calendar years.

Offerors shall provide proposed price for this CLIN on the Pricing Matrix Below.

PSC: J020

FOB: Destination

FFP

CLIN 0001 PRICING MATRIX

Quantity Year

0002 MK-82 Director DC Motor

Evaluation

UNDEFINED Each

MK-82 Director DC Motor (P/N 2907650) Evaluation IAW the SOW, Section 3.2.3 and all applicable documents. USN or FMS Assets.

CLIN 0002 PRICING MATRIX

Qty Breaks Year 1 Year 2 Year 3 Year 4 Year 5

*Offeror to propose quantity breaks

0003 MK-82 Director DC Motor Level

I Overhaul

MK-82 Director DC Motor (P/N 2907650) Level I Overhaul IAW the SOW, Section 3.2.3 and all applicable

Offerors shall provide proposed price for this CLIN on the Pricing Matrix Below..

CLIN 0003 PRICING MATRIX

*Offeror to propose quantity breaks

0004 MK-82 Director DC Motor Level

II

MK-82 Director DC Motor (P/N 2907650) Level II Overhaul IAW the SOW, Section 3.2.3 and all applicable

CLIN 0004 PRICING MATRIX

*Offeror to propose quantity breaks.

0005 MK-82 Director DC Motor Level

III

MK-82 Director DC Motor (P/N 2907650) Level III Overhaul IAW the SOW, Section 3.2.3 and all applicable

CLIN 0005 PRICING MATRIX

0006 MK-82 Director DC Motor Level

IV

MK-82 Director DC Motor (P/N 2907650) Level IV Overhaul IAW the SOW, Section 3.2.3 and all applicable

CLIN 0006 PRICING MATRIX

0007 MK-82 Director DC Motor Level

V Overhaul

MK-82 Director DC Motor (P/N 2907650) Level V Overhaul IAW the SOW, Section 3.2.3 and all applicable

CLIN 0007 PRICING MATRIX

0008 MK-82 Director DC Motor Level

VI

MK-82 Director DC Motor (P/N 2907650) Level VI Overhaul IAW the SOW, Section 3.2.3 and all applicable

CLIN 0008 PRICING MATRIX

0009 First Article New Manufacture

1 Each of MK-82 Director DC Motor (P/N 2907650) IAW the SOW, Section 3.2.6 and all applicable documents.

First Article New Manufacture will be waived by the Government if offeror has manufactured the item within the last five (5) calendar years.

NOTE: The requirements in DFARS 252.211-7003, Item Identification and Valuation, are applicable for this line item. The contractor shall provide DoD unique identification or a DoD recognized unique identification equivalent.

PSC: 6105

CLIN 0009 PRICING MATRIX

Qty Breaks Year 1

0010 MK-82 Director DC Motor New

Manufacture

New manufacture of MK-82 Director DC Motor (P/N 2907650) IAW the SOW, Section 3.2.6 and all applicable documents. USN or FMS Assets.

Offerors shall provide proposed price for this CLIN on the Pricing Matrix Below.

NOTE: The requirements in DFARS 252.211-7003, Item Identification and Valuation, are applicable for this line item. The contractor shall provide DoD unique identification or a DoD recognized unique identification

CLIN 0010 PRICING MATRIX

0011 First Article Evaluation and

First Article Requirement for the AN/SPS-49 Elevation Drive DC Motor (P/N 914104) Evaluation and Overhaul IAW the SOW, Section 3.3 and all applicable documents.

First Article Evaluation and Overhaul will be waived by the Government if offeror has overhauled the item within the last five (5) calendar years.

CLIN 0011 PRICING MATRIX

0012 AN/SPS-49 Elevation Drive DC

Motor

Evaluation

AN/SPS-49 Elevation Drive DC Motor (P/N 914104) Evaluation IAW the SOW, Section 3.3.3 and all applicable documents. USN or FMS Assets.

CLIN 0012 PRICING MATRIX

0013 AN/SPS-49 Elevation Drive DC

Level I Overhaul

AN/SPS-49 Elevation Drive DC Motor (P/N 914104) Level I Overhaul IAW the SOW, Section 3.3.3 and all

CLIN 0013 PRICING MATRIX

0014 AN/SPS-49 Elevation Drive DC

Level II Overhaul

AN/SPS-49 Elevation Drive DC Motor (P/N 914104) Level II Overhaul IAW the SOW, Section 3.3.3 and all

CLIN 0014 PRICING MATRIX

0015 AN/SPS-49 Elevation Drive DC

Level III Overhaul

AN/SPS-49 Elevation Drive DC Motor (P/N 914104) Level III Overhaul IAW the SOW, Section 3.3.3 and all

CLIN 0015 PRICING MATRIX

0016 AN/SPS-49 Elevation Drive DC

Level IV Overhaul

AN/SPS-49 Elevation Drive DC Motor (P/N 914104) Level IV Overhaul IAW the SOW, Section 3.3.3 and all

CLIN 0016 PRICING MATRIX

0017 AN/SPS-49 Elevation Drive DC

Level V Overhaul

AN/SPS-49 Elevation Drive DC Motor (P/N 914104) Level V Overhaul IAW the SOW, Section 3.3.3 and all

CLIN 0017 PRICING MATRIX

0018 AN/SPS-49 Elevation Drive DC

Motor I

Level VI Overhaul

AN/SPS-49 Elevation Drive DC Motor (P/N 914104) Level VI Overhaul IAW the SOW, Section 3.3.3 and all

CLIN 0018 PRICING MATRIX

0019 First Article New Manufacture of AN/SPS-49 Elevation Drive DC Motor (P/N 914104) IAW the SOW, Section 3.3.5

First Article New Manufacture will be waived by the Government if offeror has manufactured the item within the last five (5) calendar years.

NOTE: The requirements in DFARS 252.211-7003, Item Identification and Valuation, are applicable for this line item. The contractor shall provide DoD unique identification or a DoD recognized unique identification

CLIN 0019 PRICING MATRIX

0020 AN/SPS-49 Elevation Drive DC

New Manufacture

AN/SPS-49 Elevation Drive DC Motor (P/N 914104) New Manufacture IAW the SOW, Section 3.3.5 and all applicable documents. USN or FMS Assets.

Offerors shall provide proposed price for this CLIN on the Pricing Matrix Below.

NOTE: The requirements in DFARS 252.211-7003, Item Identification and Valuation, are applicable for this line item. The contractor shall provide DoD unique identification or a DoD recognized unique identification

CLIN 0020 PRICING MATRIX

0021 AN/SPS-49 Elevation Drive DC

Supplemental Repair - FFP

AN/SPS-49 Elevation Drive DC Motor (P/N 914104) Supplemental Repair IAW the SOW, Section 3.3.3 and all applicable documents. To be negotiated on a delivery order level. USN or FMS Assets.

CLIN 0021 PRICING

To be negotiated on a case by case basis at the time of the repair. To include above and beyond repairs identified in the evaluation and in the SOW. A FFP proposal will be completed to include supporting rationale for the requested work.

0022 MK-82 Director DC Motor

Supplemental Repair - FFP

MK-82 Director DC Motor (P/N 2907650) Supplemental Repair IAW the SOW, Section 3.2.3 and all applicable documents. To be negotiated on a delivery order level. USN or FMS Assets.

CLIN 0022 PRICING

To be negotiated on a case by case basis at the time of the repair. To include above and beyond repairs identified in the evaluation and noted in the SOW. A FFP proposal will be completed to include supporting rationale for the requested work.

ITEM

NO SUPPLIES/SERVICES QTY U/I UNIT PRICE AMOUNT

0023 Technical Data Requirements

Technical Data Requirements for CLIN(s) 0001 through 0022 IAW the Statement of Work (SOW), contract CDRLs A001 thru A007 provided in Section J, and all applicable DIDs.

The Government shall have unlimited rights to all Data/Tech Data generated under this effort IAW DFARS 252.227-7013. The price/costs for all data/tech data generated by the contractor directly or indirectly in its performance of this procurement effort is included in the price/costs paid by the Government under CLINs 0001-0022.

Not Separately Priced.

Lot

0024 Contract Ceiling

The purpose of this CLIN is to establish the contract ceiling. No orders will be placed using this CLIN.

IDC CONSTRAINTS

CONTRACT MINIMUM/MAXIMUM QUANTITY AND CONTRACT VALUE

The minimum quantity and contract value for all orders issued against this contract shall not be less than the minimum quantity and contract value stated in the following table. The maximum quantity and contract value for all orders issued against this contract shall not exceed the maximum quantity and contract value stated in the following table.

MINIMUM MINIMUM MAXIMUM MAXIMUM

QUANTITY AMOUNT QUANTITY AMOUNT

If First Article IS required for MK-82 DC Director: TBD CLIN 0001 – Qty 3 CLIN 0009 – Qty 1 If First Article IS required for AN/SPS-49 Pedestal DC Motor:

CLIN 0011 – Qty 1 CLIN 0019 – Qty 1

If First Article IS NOT required for MK-82 DC Director:

CLIN 0002 – Qty 1 If First Article IS NOT required for AN/SPS-49 Pedestal DC Motor:

CLIN 0012 – Qty 1

CLAUSES INCORPORATED BY FULL TEXT

B-215-H002 REFUNDS (SPARES AND SUPPORT EQUIPMENT) (NAVSEA) (OCT 2018)

(a) In the event that the price of a spare part or item of support equipment delivered under this contract significantly exceeds its intrinsic value, the Contractor agrees to refund the difference. Refunds will not be made to recoup the amount of cost decreases that occur over time due to productivity gains (excluding economic purchase quantity considerations) or changes in market conditions.

(b) For purposes of this requirement, the intrinsic value of an item is defined as follows:

(1) If the item is one which is sold or is substantially similar or functionally equivalent to one that is sold in substantial quantities to the general public, intrinsic value is the established catalog or market price, plus the value of any unique requirements, including delivery terms, inspection, packaging, or labeling.

(2) If there is no comparable item sold in substantial quantities to the general public, intrinsic value is defined as the price an individual would expect to pay for the item based upon an economic purchase quantity as defined in FAR 52.207-4, plus the value of any unique requirements, including delivery terms, inspection, packaging or labeling.

(c) At any time up to two years after delivery of a spare part or item of support equipment, the Contracting Officer may notify the Contractor that based on all information available at the time of the notice, the price of the part or item apparently exceeds its intrinsic value.

(d) If notified in accordance with paragraph (c) above, the Contractor agrees to enter into good faith negotiations with the Government to determine if, and in what amount, the Government is entitled to a refund.

(e) If agreement pursuant to paragraph (d) above cannot be reached, and the Navy's return of the new or unused item to the Contractor is practical, the Navy, subject to the Contractor's agreement, may elect to return the item to the Contractor.

Upon return of the item to its original point of Government acceptance, the Contractor shall refund in full the price paid.

If no agreement pursuant to paragraph (d) above is reached, and return of the item by the Navy is impractical, the Contracting Officer may, with the approval of the Head of the Contracting Activity, issue a Contracting Officer's final decision on the matter, subject to Contractor appeal as provided in the "Disputes" clause (FAR 52.233-1).

(f) The Contractor shall make refunds, as required under this requirement, in accordance with instructions from the Contracting Officer.

(g) The Contractor shall not be liable for a refund if the Contractor advised the Contracting Officer in a timely manner that the price it would propose for a spare part or item of support equipment exceeded its intrinsic value, and with such advice, specified the estimated proposed price, the estimated intrinsic value and known alternative sources or item, if any, that can meet the requirement.

(h) This requirement does not apply to any spare parts or items of support equipment whose price is determined through adequate price competition. This requirement also does not apply to any spare part or item of support equipment if the Contractor submitted, and certified the currency, accuracy and completeness of, cost or pricing data applicable to the item.

(End of text)

Section C - Descriptions and Specifications

STATEMENT OF WORK

STATEMENT OF

WORK (SOW) DIRECT

CURRENT (DC)

MOTOR OVERHAUL

AND

MANUFACTURING 22

January 2024

1. BACKGROUND AND SCOPE

This Statement of Work (SOW) establishes the requirements for the inspection, evaluation, overhaul, manufacture, and delivery of the MK-82 Gun & Guided Missile Director Direct Current Motor, PN 2907650, used in the MK-99 Fire Control System (FCS); and the AN/SPS-49 Elevation Drive Direct Current Motor (P/N 914104). Naval Surface Warfare Center (NSWC) Crane Division is the designated overhaul point for the MK-82 Gun and Guided Missile Director and AN/SPS-49 Antenna.

2. APPLICABLE DOCUMENTS

2.1. NSWC Crane Documents

SE110-A2-MMD-010 Overhaul & Repair Manual AS- 3262/SPS-49(V) 89 TRP 12 9240 Antenna Refurbishment Coating Manual TW272-AE-PRO-110 Metal Surface Coating System Refinishing Procedures

18-OL11276-01 SPS-49 DC Motor Technical Data Package as outlined in Table 2

2.2. Military Standards

MIL-STD-129P Military Marking for Shipment and Storage MIL-STD-130N Identification Marking of US Military Property MIL-STD-2073-1E Standard Practice for Military Packing

2.3. Technical Documents

2907650 Rev AC Direct Current Motor

WS10319 Rev A Direct Current Motor Specification OD17552 Rev 6 Chg 3 Wiring Procedure 914104 Rev M Elevation Drive Motor

914321 Rev D Servo Motor Tachometer Specification

2.4. Industry Standards

SAE AS5553A Fraudulent/Counterfeit Electronic Parts; Avoidance, Detection, Mitigation, and Disposition

SAE AS6081 Fraudulent/Counterfeit Electronic Parts: Avoidance, Detection, Mitigation, and Disposition - Distributors

SAE AS6174 Counterfeit Materiel; Assuring Acquisition of Authentic and

Conforming Materiel

SAE AS6301 Compliance Verification Criterion Standard for SAE AS6081, Fraudulent/Counterfeit Electronic Parts: Avoidance, Detection, Mitigation, and Disposition – Distributors

3. REQUIREMENTS

3.1. General Requirements

3.1.1. The Contractor shall furnish all equipment, parts, and labor necessary to manufacture, overhaul and test the MK-82 Director DC Motor, P/N 2907650 and the AN/SPS-49 Elevation Drive DC Motor, P/N 914104.

3.1.2. The Contractor shall be responsible for shipment of all assets submitted to the Contractor for evaluation and overhaul. Assets submitted for overhaul shall be returned to the Government per FOB Destination to NSWC Crane, Building 3168.

3.1.3. For all assets to be delivered to the Government, the Contractor shall perform marking for shipment and storage processes using MIL-STD-129P.

3.1.4. For all assets to be delivered to the Government, the Contractor shall apply equipment markings and identification processes using MIL-STD-130N.

3.1.5. All assets shall be packaged IAW MIL-STD-2073-1E Method 54 and cover all external electrical ports with plastic protective caps.

3.1.6. The Contractor shall maintain a configuration control program that meets the requirements of EIA- 649-1 Configuration Management Requirement for Defense contracts.

3.1.7. In the event it is necessary to deviate from the drawings provided based on obsolescence or diminished manufacturing sources and materiel shortages (DMSMS), the Contractor shall formally request the change in an engineering change proposal (ECP) and submit it to the Government for approval. The Government will require adequate time to review ECP's based on the magnitude of the change. Furthermore, an updated Technical Drawing Package (TDP) reflecting the changes must be provided to the Government. The updated TDP may or may not need to accompany the ECP for approval depending on whether or not it is needed to adequately describe the change. (CDRL A001) The contractor shall not proceed with any deviations until the Government has approved the ECP.

3.2. MK-82 Director Direct Current Motor Requirements (P/N 2907650)

3.2.1. General Requirements

3.2.1.1. All MK-82 Director DC Motors either manufactured or overhauled shall meet the requirements of Drawing 2907650 Rev AC and Specification WS10319 Rev A upon delivery to the Government.

3.2.2. Overhaul First Article Requirements for Direct Current Motor (P/N 2907650) (CLIN 0001)

3.2.2.1. If the Contractor HAS NOT performed duties described in this SOW to include manufacturing and/or overhaul the MK-82 Director Direct Current Motor (P/N 2907650) within the last five (5) years, the Contractor shall overhaul three (3) DC Motors IAW SOW Paragraph 3.2.3 and shall test the motors IAW SOW Paragraph 3.2.4.

3.2.2.2. All First Article testing shall have a Government witness.

3.2.2.3. All CLIN 0001 deliverables will be subjected to MK-82 Director Factory Acceptance Testing

(FAT) where assets will be installed on a MK-82 Director asset upon delivery to the

3.2.3. Overhaul Requirements for Direct Current Motor (P/N 2907650)

3.2.3.1. When subassemblies are received for overhaul, the Contractor shall perform an initial inspection and test IAW Paragraph 3.2.4 of the assembly or subassembly. (CLIN 0002). All discrepancies beyond the scope of a standard overhaul shall be documented in an Evaluation Report (CDRL A002) with accompanying documenting photograph(s). After initial inspection and test of the subassembly, the Contractor shall disassemble the subassembly. The Contractor shall perform detailed inspections, tests, and/or measurements of all parts not already designated as mandatory replacement items as part of a MK-82 Director DC Motor Level 1 Overhaul. Items that require repairs and/or replacement beyond a standard overhaul (paragraph 3.2.3.3, Level II through Level VI), are defined as extensive overhauls. Repairs not within the scope of an extensive overhaul, are defined as supplemental repairs. The Contractor shall document these non-mandatory repairs/replacement parts, which fail inspections, tests, and/or measurements, on the evaluation report and designate the failed parts as supplemental repairs. The Contractor shall include a Firm Fixed Price (FFP) for the labor and materials required for the parts deemed as needing supplemental repairs.

3.2.3.2. A MK-82 Director DC Motor Standard Overhaul, Level I (CLIN 0003), shall include the replacement of all common hardware (screws, nuts, bolts, dowels, and washers); sealing items such as gaskets, O-rings, seals, etc.; are mandatory replacement items for subassembly overhauls. Replacement of bearings, external connectors, cosmetic repairs, physical repairs, coating removal and coating/plating application (where applicable); and replacement of brushes and associated brush springs as well as removal of commutator wear to restore concentricity of commutator diameter are also required for standard overhaul. The Contractor shall provide and install new identification plates and warning labels as applicable with the same stamped information as the original plates/labels. The Contractor shall use rivets to install new identification plates and warning labels. Parts which are known to have exceeded 75% of their life expectancy based on historical reliability data shall be replaced or repaired.

3.2.3.2.1. All external surfaces shall be processed IAW Procedure TW272-AE-PRO-110R2.

3.2.3.2.2. Surfaces identified as ‘M’ within Drawing 2907650 Rev AC and all internal surfaces are considered critical surfaces and shall only be addressed in corrosion areas IAW Procedure TW272-AE-PRO-110R2 Paragraph 3-2.3.1. These surfaces shall be pretreated IAW Procedure TW272-AE-PRO-110R2 Paragraph 3-2.3.2.1.

3.2.3.3. A subassembly extensive overhaul, is in addition to a Level I overhaul and/or subsequent repairs not part of a standard overhaul as required to include:

3.2.3.3.1. MK-82 Director DC Motor Level II Overhaul (CLIN 0004) – Electric Brake Repairs.

3.2.3.3.2. MK-82 Director DC Motor Level III Overhaul (CLIN 0005) – Severe Corrosion Repairs to include replacement of housing components and cleaning/repairs to electrical connections damaged by presence of corrosion.

3.2.3.3.3. MK-82 Director DC Motor Level IV Overhaul (CLIN 0006) – Oil Intrusion Repairs to include cleansing of armature windings and electrical components.

3.2.3.3.4. MK-82 Director DC Motor Level V Overhaul (CLIN 0007) – Minor Rotor/Stator Repairs, partial magnet replacement, field coil repairs, partial armature winding repairs, and yoke repairs.

3.2.3.3.5. MK-82 Director DC Motor Level VI Overhaul (CLIN 0008) – Major Rotor/Stator Repairs to include complete magnet replacement, field coil replacement, rewinding of armature, yoke replacement, and commutator replacement.

3.2.3.4. The Contractor shall provide Evaluation Reports (CDRL A002) to the Government for each subassembly submitted for overhaul. The Contractor shall overhaul motors which have no repair requirements beyond Level I overhauls. For subassemblies which require extensive overhaul and/or supplemental repairs above and beyond the Level I overhaul shall NOT be overhauled until the Government approves the evaluation report. If the Government does not approve the evaluation report, the Contractor shall take disposition actions for the motor in accordance with the Government’s evaluation report response. When the Government approves evaluation reports, the Contractor shall execute the Level I overhaul and/or the supplemental repair (Level II through Level VI). The supplemental repair portion of the effort shall be charged to the supplemental repair Contract Line Item Number, CLIN 0022.

3.2.3.5. The Contractor shall perform a Level I overhaul and extensive overhaul (Level II through

Level VI) on MK-82 Director Direct Current Motor, P/N 2907650 as directed by orders and in accordance with Paragraph 3.2.3. The Contractor shall test the subassembly upon completion of the Level I overhaul, extensive overhaul (Level II through Level VI) and/or supplemental repair if required and approved in accordance with Paragraph 3.2.4 of this SOW.

3.2.4. Testing Requirements for Direct Current Motor (P/N 2907650)

3.2.4.1. Contractor shall test all motors IAW inspection classification of specification number

WS10319A Paragraph 4.2.b. and 4.2.2.

3.2.4.2. Contractor shall provide all reports/data per specification number WS10319A Paragraph 4.6.

(CDRL A003)

3.2.4.3. The aforementioned requirements apply and shall be performed for every overhauled motor, as stated.

3.2.5. Component Certifications for Direct Current Motor (P/N 2907650)

3.2.5.1. As specified in the drawing specifications of each assemblies’ components, Certificate of Conformance shall be delivered to the Government with each order with the exception of overhauled assets. Replaced components must be accompanied with a Certificate of Conformance. (CDRL A004)

3.2.5.2. Contractor shall inspect each manufactured item and/or purchased item against drawings/specifications and shall provide a Certificate of Compliance to document conformance of each hardware item/component with item drawings/specifications. The Contractor shall provide a hard copy of the Certificate of Compliance with each motor produced IAW with this SOW to be shipped with the motor. Contractor shall make electronic copies of the Certificate of Compliance available to the Government upon request. (CDRL A005)

3.2.6. New Manufacturing of Direct Current Motor (P/N 2907650)

3.2.6.1. First Article Requirement for Direct Current Motor (P/N 2907650) (CLIN 0009)

3.2.6.1.1. If the Contractor HAS NOT performed duties described in this SOW to include manufacturing and/or overhaul of the MK-82 Director Direct Current Motor (P/N 2907650) within the last five (5) years, the Contractor shall manufacture a new DC Motor IAW Specification WS10319A Paragraph 3.1 and SOW Paragraph 3.2.6.2 for Government inspection testing.

3.2.6.1.2. Contractor shall test all assets IAW inspection classification of specification

WS10319A Paragraph 4.2.a and 4.2.1.

3.2.6.1.3. Contractor shall provide all reports/data per SOW Paragraph 3.2.3.

3.2.6.1.4. Contractor shall provide all reports/data per Specification WS10319A Paragraph 4.7.

3.2.6.1.5. Contractor shall provide all reports/data per Specification WS10319A Paragraph 4.8.

3.2.6.1.6. All First Article Testing (FAT) shall have a Government witness.

3.2.6.1.7. All MK-82 newly manufactured motors delivered to the Government will be installed in a MK-82 Director and tested IAW the MK-82 Director Factory Acceptance Testing (FAT).

3.2.6.2. Manufacturing of Direct Current Motor (P/N 2907650) (CLIN 0010)

3.2.6.2.1. The Contractor shall manufacture MK-82 Director Direct Current Motors, P/N 2907650 per the drawing specification 10001-2907650 and Specification WS10319A and provided test documentation IAW Paragraph 3.2.3 of this SOW as applicable.

3.3. SPS-49 Antenna Elevation Drive Direct Current Motor Requirements (P/N 914104)

3.3.1. General Requirements

3.3.1.1. All SPS-49 Antenna Elevation Drive DC Motors overhauled or manufactured shall meet

Drawing 914104 Rev M, Drawing 914321 Rev D, and Repair Manual SE110-A2-MMD-010 Chapter 9 and Appendix C upon delivery to the Government.

3.3.2. Overhaul First Article Requirements for Direct Current Motor Requirements (P/N

914104) (CLIN 0011)

3.3.2.1. If the Contractor HAS NOT performed duties described in this SOW to include manufacturing and/or overhaul the SPS-49 Elevation Drive Direct Current Motor (P/N 914104) within the last five (5) years, the Contractor shall overhaul one (1) DC Motors IAW SOW Paragraph 3.3.3 and test IAW SOW Paragraph 3.3.4.

3.3.2.2. All First Article testing shall have a Government witness.

3.3.2.3. The overhauled assets will be subjected to SPS-49 Pedestal Antenna Factory Acceptance Testing (FAT) when the assets will be installed on a SPS-49 Pedestal Antenna asset upon delivery to the

3.3.3. Overhaul Requirements for Direct Current Motor Requirements (P/N 914104)

3.3.3.1. When subassemblies are received for overhaul, the Contractor shall perform an initial inspection and test IAW Paragraph 3.3.4. (CLIN 0012) All discrepancies beyond the scope of a standard overhaul shall be documented in an Evaluation Report (CDRL A002) with accompanying documenting photograph(s). After initial inspection and test of the subassembly, the Contractor shall perform disassembly, cleaning, and assessment IAW SE110-A2-MMD-010 Manual Sections II (9-2 Disassembly), III (9-3 Cleaning and Examination), Table 9.3, and Appendix C.

During cleaning, the Contractor shall remove all sealant from exterior casing and hardware. The Contractor shall perform detailed inspections, tests, and/or measurements of all parts not already designated as mandatory replacement items as part of a standard overhaul. Items which require repairs and replacement beyond an AN/SPS-49 Pedestal DC Motor Level I Overhaul (Level I) and extensive overhaul (AN/SPS-49 Pedestal DC Motor Level II Overhaul through AN/SPS-49 Pedestal DC Motor Level VI Overhaul) are defined as supplemental repairs. The Contractor shall document these non-mandatory repairs/replacement components which fail inspections, tests, and/or measurements on the evaluation report and designate the failed items as required replacement items and include a Firm Fixed Price (labor and materials) for replacement of those items.

3.3.3.2. An AN/SPS-49 Pedestal DC Motor Level I Overhaul (CLIN 0013), includes: the replacement of all components that are identified as mandatory (marked by asterisk “*”) in Tables 9-4, 9-5, 9-6, and Figure 9-3 of Repair Manual SE110-A2-MMD-010; and IAW Drawing 914104 and Specification 914321.

3.3.3.2.1. TABLE 1 of SOW Paragraph 7 denotes a Standard Overhaul parts kit.

3.3.3.3. The Contractor shall replace tachometer brushes, J1 and J2 connectors/pins, and associated hardware parts that are identified as non-mandatory in Table 9-4, 9-5, 9-6, and Figure 9-3 of Repair Manual SE110-A2-MMD-010; and IAW Drawing 914104 and Specification 914321.

3.3.3.4. If the tachometer brush holder assembly and tachometer stator assembly currently installed is not model M35000-003 and M35002-301, the Contractor shall replace the tachometer brush holder assembly and tachometer stator assembly with model M35000-003 and M35002-301.

3.3.3.5. All external surfaces shall be processed IAW 89 TRP 12 9240 per Paragraph 4.4.1 Blasting and

Paragraph 4.1.1. Paint Requirements.

3.3.3.6. All internal surfaces within Drawing 914104 Rev M are considered critical surfaces and shall only be addressed in corrosion areas IAW Procedure TW272-AE-PRO-110R2 Paragraph 3-2.3.1.

These surfaces shall be pretreated IAW Procedure TW272-AE-PRO-110R2 Paragraph 3-2.3.2.1.

3.3.3.7. The Contractor shall provide and install new identification plates and warning labels with the same stamped information as the original plates/labels removed during motor evaluation. The Contractor shall use rivets to install new identification plates and warning labels.

3.3.3.8. A subassembly extensive overhaul, is in addition to a standard overhaul and/or subsequent repairs not part of a standard overhaul as required to include:

3.3.3.8.1. AN/SPS-49 Pedestal DC Motor Level II Overhaul (CLIN 0014) – DC Motor Brush

Holder Assembly. The Contractor shall replace the DC elevation drive motor brush holder assembly and associated hardware parts that are identified as non-mandatory in Table 9-4, 9- 6, and Figure 9-3 (item number 35) of Specification SE110-A2-MMD-010; and IAW Drawing 914104 and Specification 914321.

3.3.3.8.2. AN/SPS-49 Pedestal DC Motor Level III Overhaul (CLIN 0015) –Rotor/Stator Repairs.

The Contractor shall complete partial magnet replacement, field coil repairs, partial armature winding repairs, and yoke repairs.

3.3.3.8.3. AN/SPS-49 Pedestal DC Motor Level IV Overhaul (CLIN 0016) – Armature Assembly.

The Contractor shall replace the armature assembly and associated hardware parts that are identified as non-mandatory in Table 9-4, 9-5, 9-6, and Figure 9-3 (item number 27) of Specification SE110-A2-MMD-010; and IAW Drawing 914104; and Specification 914321.

3.3.3.8.4. AN/SPS-49 Pedestal DC Motor Level V Overhaul (CLIN 0017) – Frame Assembly. The

Contractor shall replace the frame assembly and associated hardware parts that are identified as non-mandatory in Table 9-4, 9-5, 9-6, and Figure 9-3 (item number 55) of Specification SE110-A2-MMD-010; and IAW Drawing 914104 and Specification 914321.

3.3.3.8.5. AN/SPS-49 Pedestal DC Motor Level VI Overhaul (CLIN 0018) – Back End Bracket. The

Contractor shall replace the back-end bracket and associated hardware parts that are identified as non-mandatory in Table 9-4, 9-5, 9-6, and Figure 9-3 (item number 44) of Specification SE110-A2-MMD-010; and IAW Drawing 914104 and Specification 914321.

3.3.3.9. The Contractor shall provide evaluation reports (A002) to the Government for each motor submitted for overhaul. The Contractor shall overhaul motors which have no repair requirements beyond a Level I overhaul. Motors which have extensive overhaul and/or supplemental repair requirements that fall within a Level II through Level VI overhaul shall NOT be overhauled until the Government approves the evaluation report. If the Government does not approve the evaluation report, the Contractor shall take disposition actions for the subassembly in accordance with the Government’s evaluation report response. When the Government approves evaluation reports, the Contractor shall execute the Level II through Level VI overhauls. The supplemental repair portion of the effort shall be charged to the supplemental repair Contract Line Item Number, CLIN 0021.

3.3.3.10. The Contractor shall perform a Level I overhaul and Level II through Level VI overhaul on

SPS-49 Elevation Drive DC Motors as directed by orders and in accordance with Paragraph

3.3.3. The Contractor shall test the subassembly upon completion of the overhauls in accordance with Paragraph 3.3.4 of this SOW.

3.3.4. Testing Requirements for Direct Current Motor Requirements (P/N 914104)

3.3.4.1. Contractor shall test all assets IAW Specification SE110-A2-MMD-010, Chapter 9, Section 6 Paragraph 9-6 Post Reassembly Testing.

3.3.4.2. Contractor shall provide all reports/data per Specification SE110-A2-MMD-010 Section 6 Paragraph 9-6-1.

3.3.4.2.1. Exception to locked motor shaft during test: Test will be conducted using a dynamometer, and motor loaded between 30.5-31.5 amps. This requirement is in lieu of the 100amp locked rotor requirement.

3.3.4.3. Contractor shall provide all reports/data per Specification SE110-A2-MMD-010 Section 6

Paragraph 9-6-2.

3.3.4.4. Contractor shall provide all reports/data per Specification SE110-A2-MMD-010 Section 6 Paragraph 9-6-3.

3.3.4.5. Contractor shall provide all reports/data per Specification SE110-A2-MMD-010 Section 6

Paragraph 9-6-4.

3.3.4.6. Contractor shall provide all reports/data per Specification SE110-A2-MMD-010 Section 6 Paragraph 9-6-5.

3.3.4.7. Contractor shall provide all reports/data per Specification SE110-A2-MMD-010 Section 6

Paragraph 9-6.6.

3.3.4.8. Contractor shall provide all reports/data per Specification SE110-A2-MMD-010 Section 6 Paragraph 9-6-7.

3.3.4.9. Contractor shall provide all reports/data per Specification SE110-A2-MMD-010 Section 6

Paragraph 9-6-8.

3.3.4.10. The aforementioned requirements apply and shall be performed for every overhauled motor, as stated.

3.3.4.11. Test report for each overhauled asset shall show all test results in table type format comparing test values with corresponding performance requirements, difference (in percentage), allowed tolerance, and pass or fail rating. The Contractor’s test report shall identify the serial number of the refurbished motor and a hard copy of the test report shall accompany the DC Elevation Drive Motor when returned to the Government. (CDRL A003)

3.3.4.12. All SPS-49 motors overhauled and delivered to the Government will be installed in a SPS-49

Pedestal and tested IAW the SPS-49 Factory Acceptance Testing (FAT).

3.3.5. New Manufacturing of Direct Current Motor (P/N 914104)

3.3.5.1. First Article Requirement for Direct Current Motor (P/N 914104) (CLIN 0019)

3.3.5.1.1. If the Contractor HAS NOT performed duties described in this SOW to include manufacturing and/or overhaul SPS-49 Antenna Elevation Drive DC Motor within the last five (5) years, the Contractor shall manufacture a new DC Motor IAW the specification outlined in 914321 Rev D and drawing 914104 Rev M and SOW Paragraph 3.3.6. for Government inspection testing.

3.3.5.1.2. Contractor shall test all assets IAW inspection classification of specification of Specification

914321.

3.3.5.1.3. Contractor shall provide all reports/data per SOW Paragraph 3.3.4.

3.3.5.1.4. Contractor shall provide all reports/data per Specification 914321.

3.3.5.1.5. All First Article Testing (FAT) shall have a Government witness.

3.3.5.1.6. All newly manufactured SPS-49 motors delivered to the Government will be installed in a SPS-49 Pedestal and tested IAW the SPS-49 Factory Acceptance Testing (FAT).

3.3.5.2. Manufacturing of Direct Current Motor (P/N 914104) (CLIN 0020)

3.3.5.2.1. The Contractor shall manufacture SPS-49 Antenna Elevation Drive DC Motor, P/N 914104 per the Specification 914321 and provide testing documentation IAW Paragraph 3.3.4 of this SOW as applicable.

3.3.6. Component Certifications for Direct Current Motor (P/N 914104)

3.3.6.1. As specified in the drawing specifications of each assemblies’ components, a Certificate of

Conformance shall be delivered to the Government with each order with the exception of overhauled assets. Replaced components must be accompanied with a Certificate of Conformance. (CDRL A004)

3.3.6.2. The Contractor shall inspect each manufactured item and/or purchased item against drawings/specifications and shall provide a Certificate of Compliance to document conformance of each hardware item/component with item drawings/specifications. The Contractor shall provide a hard copy of the Certificate of Compliance with each item produced IAW with this SOW to be shipped with the asset. Contractor shall make electronic copies of the Certificate of Compliance available to the Government upon request. (CDRL A005)

4. GOVERNMENT FURNISHED PROPERTY

4.1. Procurement Integrated Enterprise Environment (PIEE) GFP Module Reporting

& Accountability

4.1.1. All Government Furnished Property (GFP) is property of the U.S. Government and shall not be transferred to any individual or agency, public or private, without the express written approval of the originating Contracting Officer except as required for the specific performance of tasks under this contract/order. Accountability for Government Property under this contract/order shall be managed in accordance with FAR Part 45, DFARS Part 245 and DFARS PGI Part 245, as well as the Government Property clauses in the contract/order whether acquired by the prime or subcontractors (Contractor Acquired Property), provided by the Government, or received directly from another commercial source as a deliverable from a Government issued contract.

4.1.2. Receipt Reporting- FAR 52.245-1(f)(1)(ii) requires the Contractor to report receipt of all

GFP. Reporting of Government Furnished Property (DFARS 252.211-7007(f)) and DoDI 4161.02, Accountability and Management of Government Contract Property Instruction requires that Contractors, as part of the required receipt of any Government property, report to the DoD IUID Registry using WAWF, DLMS transactions, or direct update of the registry. Contractors shall ensure appropriate accountable property records are maintained utilizing the data reported in the DoD IUID Registry and its integral GFP Module in the Procurement Integrated Enterprise Environment (PIEE).

At the time of reporting receipt of GFP in the GFP Module, the Contractor will also send an email notification to cran_gfpaccounta.fct@navy.mil to ensure the NSWC Crane Property Management Division is notified.

4.1.3. GFP Reporting- The Contractor shall provide data deliverables IAW the listed CDRLs by contract and contract order number (if applicable) to provide accountability for all Government furnished property that has been provided in support of the contract. The report shall include the fields required by the Data Item Description noted in the CDRL, DFARS 252.211-7007 and DFARS PGI 245.103-72 for the purpose of accountability.

4.2. Government Furnished Information (GFI)

4.2.1. The documents/drawings owned by the Government and listed in Section 2 of this SOW will be provided at the beginning of this contract. Military and Commercial Specification will not be provided.

4.3. Government Furnished Materiel (GFM)

4.3.1. The Government will provide AN/SPS-49 Elevation Drive DC Motors and MK-82 Director DC

Motors as required for evaluation, overhaul, and supplemental repair. (CDRL A006)

4.3.2 The Government will provide Parts Kits as stated in Paragraph 4.3.2.3 below.

4.3.3 GFM provided will be identified on a GFP attachment for each delivery order, as applicable.

4.3.4 The Contactor shall maintain a complete listing of all serial managed operating materials and supplies where title is vested to the Government.

4.3.2. Parts Kits for SPS-49 Direct Current Motors (P/N 914104)

4.3.2.1. The Contractor shall be provided with twenty-four (24) Parts Kits that contain all parts listed in

TABLE I. The Contractor shall utilize these parts as a rotatable pool to eliminate procurement lead time though out the life of the contract. The Contractor shall utilize these parts to build and expend each Parts Kit, such that it is completely used in its entirety during the execution of overhauls on each Direct Current Elevation Drive Motor. The Contractor shall replenish the Kits by the end of each Delivery Order to eliminate future production delays as a result of awaiting parts. The Contractor shall provide a GFP/GFM report with the status of the Parts Kits. (CDRL A006)

4.3.2.2. The Contractor shall stock parts and or consumables that have a shelf life in a manner that results in minimal disposal of the items due to shelf-life expiration.

4.3.2.3. The Parts Kits are considered Government Furnished Materiel. The same quantity of Kits acquired at contract start shall be returned to the Government at contract conclusion. The parts shall be packaged and marked with the part number, part name, quantity, kit name, and item number in accordance with MILSTD-129R.

4.4. Government Furnished Equipment (GFE)

4.4.1. The Government will not provide equipment for this requirement.

5. DATA DELIVERABLES

5.1. The Contractor shall submit the following data deliverables in accordance with the requirements listed in the Contractor Data Requirements Lists (CDRL’s).

CDRL: A001

DID Number: DI-MISC-80508B DID Title: Technical Report-Study/Services DID Sub-Title: Engineering Change Proposal SOW Paragraph: 3.1.7

CDRL: A002

DID Number: DI-NDTI-80809B DID Title: Test/Inspection Report DID Sub-Title: Evaluation Report SOW Paragraph: 3.2.3.4, 3.3.3.9

CDRL: A003

DID Number: DI-NDTI-80809B DID Title: Test/Inspection Report DID Sub-Title: Unit Test/Inspection Report SOW Paragraph: 3.2.4.2, 3.3.4.11

CDRL: A004

DID Number: DI-MISC-80809B DID Title: Certificate of Conformance SOW Paragraph: 3.2.5.1, 3.3.6.1

CDRL: A005

DID Number: DI-MISC-81356A DID Title: Certificate of Compliance SOW Paragraph: 3.2.5.2, 3.3.6.2

CDRL: A006

DID Number: DI-MGMT-80441D DID Title: Government Property (GP) Inventory Report SOW Paragraph: 4.3.1, 4.3.2.1

CDRL: A007

DID Number: DI-MGMT-81989 DID Title: Critical Defect Investigation Report SOW Paragraph: 6.1.3

6. SPECIAL CONDITIONS

6.1. Quality

6.1.1. Quality Program- the Contractor shall have a quality program that is ISO 9001-2015 compliant or meets the following requirements: monitor and control critical processes; continuously improve processes; establish mechanisms for performance feedback; and maintain an effective Root Cause Analysis and corrective action system.

6.1.2. Quality Assurance- the Contractor shall ensure each final manufactured or overhauled motor meets all specifications IAW the applicable drawings and subsequent referenced documents. The Contractor shall ensure that only approved parts and processes were used to fulfill requirements of this SOW. All assets shall be Government inspected and accepted at destination.

6.1.3. If a motor fails pre-inspection, during acceptance testing, or in the fleet, a Root Cause Analysis

Report shall be documented once the Contractor receives the unit. This Root Cause Analysis should document the failure, cause of failure, corrective action, and path forward to prevent the failure in the future. This Root Cause Analysis shall document the failures in a detailed manner answering why the motor failed, how the motor failed and corrective action with photographic evidence.

(CDRL A007)

6.2. Counterfeit Parts and Materiel

6.2.1. Counterfeit materiel is a serious threat to the safety and operational effectiveness of DoD systems.

The Contractor (and Subcontractors at all levels) shall implement a risk mitigation process when obtaining critically or high-risk materiel in accordance with Paragraph (6.2.1.1. and 6.2.1.2) below:

6.2.1.1. If the materiel is currently in production or currently available, the materiel shall be obtained only from authorized sources. Authorized sources are the original manufacturer, a source with the express written authority of the original manufacturer or current design activity, or an authorized aftermarket manufacturer.

6.2.1.2. If the materiel is not in production or currently available from authorized sources, the materiel shall be obtained from suppliers that meet appropriate counterfeit avoidance criteria. Counterfeit avoidance criteria can be found in Industry Standards – SAE AS5553A; SAE AS6081; SAE AS6174; and SAE AS6301.

6.2.2. Contractors shall notify the Contracting Officer when critical or high-risk materiel cannot be obtained from an authorized source. The Contractor shall take mitigating actions to authenticate the materiel if purchased from another source. The Contractor shall report instances of counterfeit and suspect counterfeit materiel to the Contracting Officer and the Government Industry Data Exchange Program (GIDEP) as soon as the Contractor becomes aware of the issue.

7. APPLICABLE TABLES

TABLE 1. SPS-49 DC MOTOR STANDARD OVERHAUL KIT PARTS LIST

Nomenclature P/N Per Kit Qty OEM Cage

Tachometer Brush C-9246 4 71310

Ball Bearing 825-05-0224-0 1 46175

Ball Bearing 825-03-0324-0 1 46175

Connector Gasket 626-18-3286-0 1 46175

Connector Gasket 626-18-3287-0 1 46175

Hand Hole Cover Gasket 626-18-3288-0 4 46175

Motor Brush 619-43-1517-0 4 46175

Tachometer Cover Gasket 626-18-3289-0 1 46175

Warning Plate 827-05-0201-0 1 46175

Identification Plate 827-06-0434-0 1 46175

Identification Plate 827-06-0435-0 1 46175

Connector J1 MS3402D18-1P 1 96906

Connector J2 MS3402D22-22P 1 96906

Thermal Protector S1 878-06-6700-0 1 46175

Thermal Protector S2 878-06-6800-0 1 46175

Screw, Pan Head, Cross-Recessed MS51957-63 30 96906

Washer, Lock Spring MS35338-138 30 96906

Washer, Flat MS15795-846 20 96906

Washer, Sealing NAS1598C4R 20 96906

Screw, Cap, Hexagon Socket Head MS16995-41 4 96906

Screw, Cap, Hexagon Socket Head MS16995-53 3 96906

Washer, Lock Spring MS35338-139 8 96906

Washer, Lock Spring MS35338-135 12 96906

Screw, Pan Head, Cross-Recessed MS51957-19 8 96906

Screw, Drive, Round Head MS21318-27 6 96906

Nut, Plain Hexagon MS35691-2 2 96906

Motor Brush 619-43-1517 4 46175

Screw, Cap, Socket MS16995-52 5 96906

Thermal Protector S1 876-06-6700 1 46175

Screw Pan Head, Cross-Recessed MS51957-13 4 96906

Nut, Hexagon MS35649-244 4 96906

Thermal Protector S2 878-06-6800 1 46175

TABLE 2. SPS-49 DC MOTOR TECHNICAL DATA PACKAGE

Drawing Number Title

00P11276-0001 BEARING

00T11276-0000 SHAFT

00X11276-0100 BREAING BRKT CASTING

00X11276-0101 BREAING BRKT MACHINED

00X11276-0200 FRONT BRG BRKT CASTING

00X11276-0201 Rev A FRONT BRG BRKT MACHINE

00X11276-0201 FRONT BRG BRKT MACHINE

08T11276-0014 FRONT END BEARING INSERT

08T11276-0113 CORE MACHINED

10P11276-0001 CONNECTOR J1

10P11276-0002 CONNECTOR J2

10T11276-0001 BEARING SPACER

10T11276-0002 GASKET

10T11276-0003 GASKET

10T11276-0004 HAND HOLE COVER GASKET

10T11276-0006 TACHOMETER COVER GASKET

12T11276-0001 END CAP

14P11276-0001 THERMAL PROTECTOR S1

14P11276-0002 THERMAL PROTECTOR S2

14T11276-0100 ODE END PLATE

14T11276-0200 DE END PLATE

180L11276-0001 OUTLINE DRAWING

19T11276-0001 STATOR WEDGE

20P11276-0000 MAGNET SASTOR CORE

25T11276-0101 YOKE BRUSH HOLDER ASSEMBLY

20T11276-0001 TACHOMETER COVER

26X11276-0100 MOUNTING RING CASTING

26X11276-0101 MOUNTING RING MACHINING

27S11276-0000 BRUSH HOLDER ASSEMBLY

40P11276-0001 WOUND MACHINED ARMATURE

40P11276-0002 TACH. BRUSH HOLDER ASSY.

40P11276-0003 TACH. STATOR ASSEMBLY

50P11276-0001 FLATWASHER, #8

50P11276-0002 FLATWASHER, #10

50P11276-0004 HEX NUT, #8-32

50P11276-0005 SHCS, #10-24

50P11276-0006 DRIVE SCREW, ROUND HEAD

50P11276-0007 SCREW, PAN HEAD #4-40

50P11276-0008 SCREW, PAN HEAD #4-40

50P11276-0009 SEALING WASHER, #12

50P11276-0012 SELF-LOCKING NUT, HEXAGON

50P11276-0013 PAN-HEADED SLOTTED SCREW

50P11276-…