2241455_Addendum 1 08.20.2026.pdf

TOWN OF QUEENSBURY – WEST END PARK IMPROVEMENTS

LaBella Project No. 2241455

Addendum 1

August 20, 2026

A. Bidding Requirements

1. Attached are the revised sheets G-002 NOTES, C110 SITE PREPARATION PLANS, AND C530

SITE DETAILS. Please incorporate these sheets into your bid package.

a) G002 NOTES: Revise PLANTING NOTES #6 to read ”Topsoil: Provide 4” depth imported topsoil in all lawn and planting areas..

b) C110 SITE PREPARATION PLANS:

i. Revise notes pertaining to stripping and stockpiling topsoil on plan 1/C110 Base Bid Site Preparation Plan – Park Improvements and 2/C110 Alternates Site Preparation Plan to read “ REMOVE EXISTING LAWN IN DISTURBANCE LIMITS.”

ii. Omit Temporary Soil Stockpile from plan 1/C110 Base Bid Site Preparation Plan

– Park Improvements and 2/C110 Alternates Site Preparation Plan

iii. Add following note to 1/C110 Base Bid Site Preparation Plan – Park Improvements and 2/C110 Alternates Site Preparation Plan: “SOIL MATERIAL

EXCAVATED TO INSTALL SITE IMPROVEMENTS SHALL BE LOADED, HAULED

AWAY AND DISPOSED OF OFF-SITE IN A MANNER TO MINIMIZE SITE

DISTURBANCE.”

c) C530 SITE DETAILS: Omit detail 3/C530 Temporary Soil Stockpile Detail.

2. Attached is the revised specification, 329300 “PLANTS” Please incorporate this specification into your bid package.

a) Revise Specification 329300 PART 2, Section 2.5 PLANTING SOIL, Item A. to read, “Topsoil: As indicated in specification section 329120.”

B. Written and Verbal Questions and Responses – not applicable

329300-1 PLANTS

SECTION 329300

PLANTS

PART 1 - GENERAL

1.1 RELATED DOCUMENTS

A. Drawings and general provisions of the Contract, including General and Supplementary

Conditions and Division 01 Specification Sections, apply to this Section.

1.2 SUMMARY

A. Section Includes:

1. Plants.

2. Planting soil.

3. Tree stabilization.

B. Related Requirements:

1. Earthwork: Section 310000.

2. Topsoil: Section 329120

3. Seeding: Section 329219.

1.3 DEFINITIONS

A. Backfill: The earth used to replace or the act of replacing earth in an excavation.

B. Balled and Burlapped Stock: Plants dug with firm, natural balls of earth in which they were grown, with a ball size not less than diameter and depth recommended by ANSI Z60.1 for type and size of plant required; wrapped with burlap, tied, rigidly supported, and drum laced with twine with the root flare visible at the surface of the ball as recommended by ANSI Z60.1.

C. Balled and Potted Stock: Plants dug with firm, natural balls of earth in which they are grown and placed, unbroken, in a container. Ball size is not less than diameter and depth recommended by ANSI Z60.1 for type and size of plant required.

D. Container-Grown Stock: Healthy, vigorous, well-rooted plants grown in a container, with a well-established root system reaching sides of container and maintaining a firm ball when removed from container. Container shall be rigid enough to hold ball shape and protect root mass during shipping and be sized according to ANSI Z60.1 for type and size of plant required.

E. Finish Grade: Elevation of finished surface of planting soil.

F. Manufactured Topsoil: Soil produced off-site by homogeneously blending mineral soils or sand with stabilized organic soil amendments to produce topsoil or planting soil.

329300-2 PLANTS

G. Pesticide: A substance or mixture intended for preventing, destroying, repelling, or mitigating a pest. Pesticides include insecticides, miticides, herbicides, fungicides, rodenticides, and molluscicides. They also include substances or mixtures intended for use as a plant regulator, defoliant, or desiccant. Some sources classify herbicides separately from pesticides.

H. Pests: Living organisms that occur where they are not desired or that cause damage to plants, animals, or people. Pests include insects, mites, grubs, mollusks (snails and slugs), rodents

(gophers, moles, and mice), unwanted plants (weeds), fungi, bacteria, and viruses.

I. Planting Area: Areas to be planted.

J. Planting Soil: Existing, on-site soil; imported soil; or manufactured soil that has been modified with soil amendments and perhaps fertilizers to produce a soil mixture best for plant growth.

K. Plant; Plants; Plant Material: These terms refer to vegetation in general, including trees, shrubs, vines, ground covers, ornamental grasses, bulbs, corms, tubers, or herbaceous vegetation.

L. Root Flare: Also called "trunk flare." The area at the base of the plant's stem or trunk where the stem or trunk broadens to form roots; the area of transition between the root system and the stem or trunk.

M. Stem Girdling Roots: Roots that encircle the stems (trunks) of trees below the soil surface.

N. Subgrade: The surface or elevation of subsoil remaining after excavation is complete, or the top surface of a fill or backfill before planting soil is placed.

1.4 ACTION SUBMITTALS

A. Product Data: For each type of product.

1. Plant Materials: Include quantities, sizes, quality, and sources for plant materials.

B. Samples for Verification: For each of the following:

1. Organic Mulch: 1-pint volume of each organic mulch required; in sealed plastic bags labeled with composition of materials by percentage of weight and source of mulch. Each

Sample shall be typical of the lot of material to be furnished; provide an accurate representation of color, texture, and organic makeup.

1.5 INFORMATIONAL SUBMITTALS

A. Qualification Data: For landscape Installer. Include list of similar projects completed by

Installer demonstrating Installer's capabilities and experience. Include project names, addresses, and year completed, and include names and addresses of owners' contact persons.

B. Product Certificates: For each type of manufactured product, from manufacturer, and complying with the following:

329300-3 PLANTS

1. Manufacturer's certified analysis of standard products.

C. Pesticides and Herbicides: Product label and manufacturer's application instructions specific to

Project.

D. Sample Warranty: For special warranty.

1.6 QUALITY ASSURANCE

A. Installer Qualifications: Engage an experienced Installer who has completed five or more landscaping projects similar in material, design, value, and extent to that indicated for this

Project and with a record of successful grass and landscape establishment.

1. Installer’s Field Supervision: Require Installer to maintain an experienced full-time supervisor on the Project site during times that grass planting and landscaping are in progress. Field supervisor shall have had a supervisory role on a minimum of five projects of comparable scope.

B. Provide quality, size, genus, species, and variety of plants indicated, complying with applicable requirements in ANSI Z60.1.

C. Measurements: Measure according to ANSI Z60.1. Do not prune to obtain required sizes.

1. Trees and Shrubs: Measure with branches and trunks or canes in their normal position.

Take height measurements from or near the top of the root flare for field-grown stock and container-grown stock. Measure main body of tree or shrub for height and spread; do not measure branches or roots tip to tip. Take caliper measurements 6 inches above the root flare for trees up to 4-inch caliper size, and 12 inches above the root flare for larger sizes.

D. Plant Material Observation: Landscape Architect may observe plant material either at place of growth or at site before planting for compliance with requirements for genus, species, variety, cultivar, size, and quality. Landscape Architect may also observe trees and shrubs further for size and condition of balls and root systems, pests, disease symptoms, injuries, and latent defects and may reject unsatisfactory or defective material at any time during progress of work.

Remove rejected trees or shrubs immediately from Project site.

1. Notify Landscape Architect of sources of planting materials seven days in advance of delivery to site.

1.7 DELIVERY, STORAGE, AND HANDLING

A. Packaged Materials: Deliver packaged materials in original, unopened containers showing weight, certified analysis, name and address of manufacturer, and indication of compliance with state and Federal laws if applicable.

B. Bulk Materials:

329300-4 PLANTS

1. Do not dump or store bulk materials near structures, utilities, walkways and pavements, or on existing turf areas or plants.

2. Provide erosion-control measures to prevent erosion or displacement of bulk materials;

discharge of soil-bearing water runoff; and airborne dust reaching adjacent properties, water conveyance systems, or walkways.

3. Accompany each delivery of bulk materials with appropriate certificates.

C. Do not prune trees before delivery. Protect bark, branches, and root systems from sun scald, drying, wind burn, sweating, whipping, and other handling and tying damage. Do not bend or bind-tie trees in such a manner as to destroy their natural shape. Provide protective covering of plants during shipping and delivery. Do not drop plants during delivery and handling.

D. Handle planting stock by root ball.

E. Apply antidesiccant to trees using power spray to provide an adequate film over trunks (before wrapping), branches, stems, twigs, and foliage to protect during digging, handling, and transportation.

1. If deciduous trees are moved in full leaf, spray with antidesiccant at nursery before moving and again two weeks after planting.

F. Wrap trees with burlap fabric over trunks, branches, stems, twigs, and foliage to protect from wind and other damage during digging, handling, and transportation.

G. Deliver plants after preparations for planting have been completed, and install immediately. If planting is delayed more than six hours after delivery, set plants and trees in their appropriate aspect (sun, filtered sun, or shade), protect from weather and mechanical damage, and keep roots moist.

1. Heel-in bare-root stock. Soak roots that are in less than moist condition in water for two hours. Reject plants with dry roots.

2. Set balled stock on ground and cover ball with soil, peat moss, sawdust, or other acceptable material.

3. Do not remove container-grown stock from containers before time of planting.

4. Water root systems of plants stored on-site deeply and thoroughly with a fine-mist spray.

Water as often as necessary to maintain root systems in a moist, but not overly wet condition.

1.8 FIELD CONDITIONS

A. Field Measurements: Verify actual grade elevations, service and utility locations, irrigation system components, and dimensions of plantings and construction contiguous with new plantings by field measurements before proceeding with planting work.

B. Interruption of Existing Services or Utilities: Do not interrupt services or utilities to facilities occupied by Owner or others unless permitted under the following conditions and then only after arranging to provide temporary services or utilities according to requirements indicated:

329300-5 PLANTS

1. Notify Landscape Architect no fewer than two days in advance of proposed interruption of each service or utility.

2. Do not proceed with interruption of services or utilities without Architect's written permission.

C. Planting Restrictions: Plant during one of the following periods. Coordinate planting periods with maintenance periods to provide required maintenance from date of Substantial Completion.

1. Spring Planting: March 15th to June 1st

2. Fall Planting: August 15th to October 15th

D. Weather Limitations: Proceed with planting only when existing and forecasted weather conditions permit planting to be performed when beneficial and optimum results may be obtained. Apply products during favorable weather conditions according to manufacturer's written instructions and warranty requirements.

E. Coordination with Turf Areas (Lawns): Plant trees, shrubs, and other plants after finish grades are established and before planting turf areas unless otherwise indicated.

1. When planting trees, shrubs, and other plants after planting turf areas, protect turf areas, and promptly repair damage caused by planting operations.

1.9 WATER SUPPLY FOR LANDSCAPE ESTABLISHMENT AND MAINTENANCE

A. The Contractor shall be responsible for furnishing and supplying water for all turf and planting areas until final project acceptance.

B. If the Contractor utilizes the Owner’s water supply during the landscape establishment and maintenance period, the Contractor shall be responsible to pay all usage fees and costs associated with the water usage.

1.10 WARRANTY

A. Special Warranty: Installer agrees to repair or replace plantings and accessories that fail in materials, workmanship, or growth within specified warranty period.

1. Failures include, but are not limited to, the following:

a. Death and unsatisfactory growth, except for defects resulting from abuse, lack of adequate maintenance, or neglect by Owner.

b. Structural failures including plantings falling or blowing over.

2. Warranty Periods: From date of one year after Substantial Completion and acceptance of entire project:

a. Plant Material: 12 months.

3. Include the following remedial actions as a minimum:

329300-6 PLANTS

a. Immediately remove dead plants and replace unless required to plant in the succeeding planting season.

b. Replace plants that are more than 25 percent dead or in an unhealthy condition at end of warranty period.

c. A limit of one replacement of each plant is required except for losses or replacements due to failure to comply with requirements.

d. Provide extended warranty for period equal to original warranty period, for replaced plant material.

PART 2 - PRODUCTS

2.1 TREE AND SHRUB MATERIAL

A. General: Furnish nursery-grown trees and shrubs conforming to ANSI Z60.1, with healthy root systems developed by transplanting or root pruning. Provide well-shaped, fully branched, healthy, vigorous stock free of disease, insects, eggs, larvae, and defects such as knots, sun scald, injuries, abrasions, and disfigurement.

B. Grade: Provide trees and shrubs of sizes and grades conforming to ANSI Z60.1 for type of trees and shrubs required. Trees and shrubs of a larger size may be used if acceptable to Owner’s

Representative, with a proportionate increase in size of roots or balls.

C. Label each tree and shrub with securely attached, waterproof tag bearing legible designation of botanical and common name.

2.2 INORGANIC SOIL AMENDMENTS

A. Lime: ASTM C 602, agricultural liming material containing a minimum of 80 percent calcium carbonate equivalent and as follows:

1. Class: T, with a minimum of 99 percent passing through No. 8 sieve and a minimum of

75 percent passing through No. 60 sieve.

2. Class: O, with a minimum of 95 percent passing through No. 8 sieve and a minimum of

55 percent passing through No. 60 sieve.

3. Provide lime in form of ground dolomitic limestone.

B. Agricultural Gypsum: Minimum 90 percent calcium sulfate, finely ground with 90 percent passing through No. 50 sieve.

2.3 ORGANIC SOIL AMENDMENTS

A. Compost: Well-composted, stable, and weed-free organic matter, pH range of 5.5 to 8; moisture content 35 to 55 percent by weight; 100 percent passing through 1-inch sieve; soluble salt content of 5 to 10 decisiemens/m; not exceeding 0.5 percent inert contaminants and free of substances toxic to plantings; and as follows:

329300-7 PLANTS

1. Organic Matter Content: 50 to 60 percent of dry weight.

2. Feedstock: Agricultural, food, or industrial residuals; biosolids; yard trimmings; or source-separated or compostable mixed solid waste.

2.4 FERTILIZERS

A. Slow-Release Fertilizer: Granular or pelleted fertilizer or slow-release tablets consisting of 50 percent water-insoluble nitrogen, phosphorus, and potassium in the following composition:

1. Composition: 20 percent nitrogen, 10 percent phosphorous, and 5 percent potassium, by weight.

2. Composition: Nitrogen, phosphorous, and potassium in amounts recommended in topsoil reports from a qualified soil-testing laboratory.

2.5 PLANTING SOIL

A. Topsoil: As indicated in specification section 329120. Provide from existing stockpiles of surface soil stripped from the project site and approved by the Engineer/Landscape Architect.

Provide imported topsoil if existing on-site surface soil is not available in sufficient quantity to meet project needs.

B. Planting Soil: Mix in bulk on site prior to placement or amend individual planting pits in undisturbed areas. Planting soil shall consist of by volume:

1. (1) One part Compost

2. (4) Four parts Topsoil

2.6 MULCH

A. Mulch: Free from deleterious materials and suitable as a top dressing of trees and shrubs, consisting of one of the following:

1. Type: Shredded hardwood.

2. Size Range: 2 inches maximum, 1/2 inch minimum.

3. Color: Natural.

2.7 PESTICIDES

A. General: Pesticide registered and approved by the EPA, acceptable to authorities having jurisdiction, and of type recommended by manufacturer for each specific problem and as required for Project conditions and application. Do not use restricted pesticides unless authorized in writing by authorities having jurisdiction.

B. Pre-Emergent Herbicide (Selective and Nonselective): Effective for controlling the germination or growth of weeds within planted areas at the soil level directly below the mulch layer.

dcarr Cloud

329300-8 PLANTS

C. Post-Emergent Herbicide (Selective and Nonselective): Effective for controlling weed growth that has already germinated.

2.8 MISCELLANEOUS PRODUCTS

A. Antidesiccant: Water-insoluble emulsion, permeable moisture retarder, film forming, for trees.

Deliver in original, sealed, and fully labeled containers and mix according to manufacturer's written instructions.

B. Burlap: Non-synthetic, biodegradable.

PART 3 - EXECUTION

3.1 EXAMINATION

A. Examine areas to receive plants, with Installer present, for compliance with requirements and conditions affecting installation and performance of the Work.

1. Verify that no foreign or deleterious material or liquid such as paint, paint washout, concrete slurry, concrete layers or chunks, cement, plaster, oils, gasoline, diesel fuel, paint thinner, turpentine, tar, roofing compound, or acid has been deposited in soil within a planting area.

2. Verify that plants and vehicles loaded with plants can travel to planting locations with adequate overhead clearance.

3. Suspend planting operations during periods of excessive soil moisture until the moisture content reaches acceptable levels to attain the required results.

4. Uniformly moisten excessively dry soil that is not workable or which is dusty.

B. If contamination by foreign or deleterious material or liquid is present in soil within a planting area, remove the soil and contamination as directed by Landscape Architect and replace with new planting soil.

C. Proceed with installation only after unsatisfactory conditions have been corrected.

3.2 PREPARATION

A. Protect structures, utilities, sidewalks, pavements, and other facilities and turf areas and existing plants from damage caused by planting operations.

B. Lay out individual tree locations and areas for multiple plantings. Stake locations, outline areas, adjust locations when requested, and obtain Landscape Architect's acceptance of layout before excavating or planting. Make minor adjustments as required.

C. Wrap trees and shrubs with burlap fabric over trunks, branches, stems, twigs, and foliage to protect from wind and other damage during digging, handling, and transportation.

329300-9 PLANTS

3.3 SPREADING PLANTING SOIL

A. Perform planting soil spreading operations only during dry weather.

B. To insure a proper bond with the existing soil, harrow or otherwise loosen the subgrade to a depth of 6 inches before spreading planting soil.

C. Spread planting soil directly upon prepared subgrade to a specified in section 329120 ‘Topsoil’ after natural settlement in areas to be planted. Smooth out unsightly variations, bumps, ridges, and depressions which will hold water. Remove stones, litter, or other objectionable material.

Finished surfaces shall conform to the contour lines and elevations indicated on the drawings or fixed by the Owner’s Representative

3.4 SPREADING LIMESTONE

A. Provide limestone soil amendment only per the recommendations of topsoil analysis tests results and at rates directed for the establishment of woody plantings. Spread ground limestone evenly over the top-soiled surface. Incorporate limestone within the top 2 inches of soil prior to finish raking.

3.5 PLANTING AREA ESTABLISHMENT

A. Perform topsoil spreading operations only during dry weather.

B. Loosen subgrade of planting areas to a minimum depth of 4 inches. Remove stones larger than 1 inch in any dimension and sticks, roots, rubbish, and other extraneous matter and legally dispose of them off Owner's property.

1. Spread planting soil to specified in section 329300 ‘Topsoil’ but not less than required to meet finish grades after natural settlement. Do not spread if planting soil or subgrade is frozen, muddy, or excessively wet.

a. Spread approximately one-half the thickness of planting soil over loosened subgrade. Mix thoroughly into top 2 inches of subgrade. Spread remainder of planting soil.

C. Finish Grading: Grade planting areas to a smooth, uniform surface plane with loose, uniformly fine texture. Roll and rake, remove ridges, and fill depressions to meet finish grades.

D. Before planting, obtain Landscape Architect's acceptance of finish grading; restore planting areas if eroded or otherwise disturbed after finish grading.

3.6 EXCAVATION FOR TREES AND SHRUBS

A. Planting Pits: Excavate planting pits as indicated on the Drawings.

329300-10 PLANTS

1. Do not excavate deeper than depth of the root ball, measured from the root flare to the bottom of the root ball.

2. If area under the plant was initially dug too deep, add soil to raise it to the correct level and thoroughly tamp the added soil to prevent settling.

3. Maintain supervision of excavations during working hours.

B. Backfill Soil: Subsoil and topsoil removed from excavations may not be used as backfill soil unless otherwise indicated.

C. Obstructions: Notify Landscape Architect if unexpected rock or obstructions detrimental to trees or shrubs are encountered in excavations.

D. Drainage: Notify Landscape Architect if subsoil conditions evidence unexpected water seepage or retention in tree or shrub planting pits.

E. Fill excavations with water and allow to percolate away before positioning trees and shrubs.

3.7 TREE AND SHRUB PLANTING

A. Inspection: Before planting, verify that root flare is visible at top of root ball according to

ANSI Z60.1. If root flare is not visible, remove soil in a level manner from the root ball to where the top-most root emerges from the trunk. After soil removal to expose the root flare, verify that root ball still meets size requirements.

B. Roots: Remove stem girdling roots and kinked roots. Remove injured roots by cutting cleanly;

do not break.

C. Balled and Burlapped Stock: Set each plant plumb and in center of planting pit or trench with root flare 1 inch above adjacent finish grades.

1. Backfill: Planting soil.

2. After placing some backfill around root ball to stabilize plant, carefully cut and remove burlap, rope, and wire baskets from tops of root balls and from sides, but do not remove from under root balls. Remove pallets, if any, before setting. Do not use planting stock if root ball is cracked or broken before or during planting operation.

3. Backfill around root ball in layers, tamping to settle soil and eliminate voids and air pockets. When planting pit is approximately one-half filled, water thoroughly before placing remainder of backfill. Repeat watering until no more water is absorbed.

4. Continue backfilling process. Water again after placing and tamping final layer of soil.

D. Container-Grown Stock: Set each plant plumb and in center of planting pit or trench with root flare 1 inch above adjacent finish grades.

1. Backfill: Planting soil.

2. Carefully remove root ball from container without damaging root ball or plant.

3. Backfill around root ball in layers, tamping to settle soil and eliminate voids and air pockets. When planting pit is approximately one-half filled, water thoroughly before placing remainder of backfill. Repeat watering until no more water is absorbed.

329300-11 PLANTS

4. Continue backfilling process. Water again after placing and tamping final layer of soil.

3.8 TREE AND SHRUB PRUNING

A. Prune, thin, and shape trees, shrubs, and vines according to standard professional horticultural and arboricultural practices. Unless otherwise indicated by Landscape Architect, do not cut tree leaders; remove only injured, dying, or dead branches from trees and shrubs; and prune to retain natural character.

B. Do not apply pruning paint to wounds.

3.9 TREE STABILIZATION

A. Install trunk stabilization as indicated on the contract drawings.

3.10 PLANTING AREA MULCHING

A. Mulch backfilled surfaces of planting areas and other areas indicated.

1. Tree planting pits in Turf Areas: Apply organic mulch ring of 3-inch uniform thickness, with 60-inch radius around trunks or stems. Do not place mulch within 3 inches of trunks or stems.

2. Mulch in Planting Beds: Apply 3-inch uniform thickness of mulch over whole surface of planting area, and finish level with adjacent finish grades. Do not place mulch within 3 inches of trunks or stems.

3.11 PLANT MAINTENANCE

A. Maintain plantings by pruning, cultivating, watering for 60 days, weeding, fertilizing, mulching, restoring planting saucers, adjusting and repairing tree-stabilization devices, resetting to proper grades or vertical position, and performing other operations as required to establish healthy, viable plantings.

B. Fill in, as necessary, soil subsidence that may occur because of settling or other processes.

Replace mulch materials damaged or lost in areas of subsidence.

C. Apply treatments as required to keep plant materials, planted areas, and soils free of pests and pathogens or disease. Use integrated pest management practices when possible to minimize use of pesticides and reduce hazards. Treatments include physical controls such as hosing off foliage, mechanical controls such as traps, and biological control agents.

3.12 PESTICIDE APPLICATION

A. Coordinate applications with Owner's operations and others in proximity to the Work. Notify

Owner before each application is performed.

329300-12 PLANTS

B. Pre-Emergent Herbicides (Selective and Nonselective): Apply to tree, shrub, and ground-cover areas according to manufacturer's written recommendations. Do not apply to seeded areas.

C. Post-Emergent Herbicides (Selective and Nonselective): Apply only as necessary to treat already-germinated weeds and according to manufacturer's written recommendations.

3.13 REPAIR AND REPLACEMENT

A. General: Repair or replace existing or new trees and other plants that are damaged by construction operations, in a manner approved by Landscape Architect.

1. Submit details of proposed pruning and repairs.

2. Perform repairs of damaged trunks, branches, and roots within 24 hours, if approved.

3. Replace trees and other plants that cannot be repaired and restored to full-growth status, as determined by Landscape Architect.

B. Remove and replace trees that are more than 25 percent dead or in an unhealthy condition before the end of the corrections period or are damaged during construction operations that Architect determines are incapable of restoring to normal growth pattern.

1. Provide new trees of same size as those being replaced for each tree of 6 inches or smaller in caliper size.

2. Species of Replacement Trees: Same species being replaced.

3.14 CLEANING AND PROTECTION

A. During planting, keep adjacent paving and construction clean and work area in an orderly condition. Clean wheels of vehicles before leaving site to avoid tracking soil onto roads, walks, or other paved areas.

B. Remove surplus soil and waste material including excess subsoil, unsuitable soil, trash, and debris and legally dispose of them off Owner's property.

C. Protect plants from damage due to landscape operations and operations of other contractors and trades. Maintain protection during installation and maintenance periods. Treat, repair, or replace damaged plantings.

D. After installation and before Substantial Completion, remove nursery tags, nursery stakes, tie tape, labels, wire, burlap, and other debris from plant material, planting areas, and Project site.

3.15 DISPOSAL

A. Remove surplus soil and waste material including excess subsoil, unsuitable soil, trash, and debris and legally dispose of them off Owner's property.

END OF SECTION 329300

W W

W W

W W

UT

OH

W

OH

W

OH

W

OH

W

OH

W

OH

W

OHW

OHW

W

W

W

W

W

W

W

W

W

W

W

W W

W

W W

W W

W

ASPHALT

SWINGSET

OHW

OHW

OHW

OHWOHWOHWOHWOHWOHWOHWOHWOHWOHW

OHW

CHAINLINK FENCE

PLAY GROUNDEQUIPMENT

BASKETBALL COURTASPHALT

PAVILIONCONCRETE

BENCHES

TRASH

ASPHALT

CHAINLINK FENCE

W W

W W

W W

UT

OH

W

OH

W

OH

W

OH

W

OH

W

OH

W

OHW

OHW

W

W

W

W

W

W

W

W

W

W

W

W W

W

W W

W W

W

ASPHALT

SWINGSET

OHW

OHW

OHW

OHWOHWOHWOHWOHWOHWOHWOHWOHWOHW

OHW

CHAINLINK FENCE

PLAY GROUNDEQUIPMENT

BASKETBALL COURTASPHALT

PAVILIONCONCRETE

BENCHES

TRASH

ASPHALT

CHAINLINK FENCE

SITE PREPARATION LEGEND:

RD/DC

DCM/JQ

Revisions

NO: DATE: DESCRIPTION:

1 08/19/2026 Addendum 1

DRAWING NAME:

8/

/2

1:

:1

PM

DRAWING NUMBER:

DATE:

ISSUED FOR:

DRAWN BY:

REVIEWED BY:

PROJECT NUMBER:

© 2024 LaBella Associates

B:

\G

LO

BA

L\ Pr oj ec ts \Q ue en sb ur y, T ow n of \2

W es t E nd

P ar k M as te r P la n De v\

_D ra w in gs \C iv il\

_C

0_

5_

DE

M

O.

dw g

Town of Queensbury 742 Bay Road Queensbury, NY 12804

West End Park Improvements

117 Luzerne Road Queensbury, NY 12804

2241455

ISSUED FOR BID

JULY 31, 2026

It is a violation of New York Education Law Art. 145 Sec.

7209 & Art. 147 Sec. 7307, for any person, unless acting under the direction of a licensed architect, professional engineer, or land surveyor, to alter an item in any way. If an item bearing the seal of an architect, engineer, or land surveyor is altered; the altering architect, engineer, or land surveyor shall affix to the item their seal and notation

"altered by" followed by their signature and date of such alteration, and a specific description of the alteration.

4 British American Boulevard Latham, NY 12110 518-439-8235 labellapc.com

CERTIFICATE OF AUTHORIZATION NUMBER:

PROFESSIONAL ENGINEERING: 018281

LAND SURVEYING: 017976

GEOLOGICAL: 018750

PROJECT NAME:

CLIENT NAME:

E

S IO R

N o.

N C

EX E

T

O

F

E

S

T A

L

K

- 1

W Y

O R

R

M

A

.C

EAP

S C

G L

D O U

D

N AS

AL

C T

HC

O R D c C I

E T

EXP: 01/31/2027

C110

SITE PREPARATION

PLANS

C110

2 ALTERNATES SITE PREPARATION PLAN

SCALE: 1" = 20'

C110

1 BASE BID SITE PREPARATION PLAN - PARK IMPROVEMENTS

SCALE: 1" = 20'

ALTERNATE NO. 1: PARK

IMPROVEMENTS -

ASPHALT CONNECTOR

WALK

ALTERNATE NO. 2:

PLAYGROUND EXPANSION

IMPROVEMENTS

ALTERNATE NO. 3:

BASKETBALL COURT

RESURFACING

AutoCAD SHX Text

CEDAR HEDGE

AutoCAD SHX Text

CEDAR HEDGE

AutoCAD SHX Text

EXISTING TREES REMAIN, PROTECT

AutoCAD SHX Text

TREE PROTECTION FENCING

AutoCAD SHX Text

PAVEMENT SAWCUT LINE

AutoCAD SHX Text

PROJECT BOUNDARY

AutoCAD SHX Text

AutoCAD SHX Text

ORIGINAL SCALE 1"=

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text 20'

AutoCAD SHX Text PRIOR TO ANY WORK ON THE PROJECT SITE THE CONTRACTOR SHALL COORDINATE WITH THE TOWN OF QUEENSBURY AND THE ADJACENT PROPERTY OWNER FOR ANY ACCESS AGREEMENTS THAT MAY BE REQUIRED

AutoCAD SHX Text

AutoCAD SHX Text

ORIGINAL SCALE 1"=

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text 20'

AutoCAD SHX Text

EXISTING FEATURE TO BE REMOVED

AutoCAD SHX Text

NOT IN CONTRACT

AutoCAD SHX Text N.I.C.

AutoCAD SHX Text

WORK LIMITS

AutoCAD SHX Text

EXISTING TREES TO REMAIN AND BE PROTECTED (TYP)

AutoCAD SHX Text

REMOVE EXISTING PLASTIC PERIMETER CURB

AutoCAD SHX Text

REMOVE & RELOCATE EXISTING WASTE RECEPTACLE & SIGN

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

EXISTING ASPHALT PAVEMENT & GRANITE CURBING REMAIN, PROTECT

AutoCAD SHX Text SAWCUT LINE; REMOVE EXISTING ASPHALT PAVEMENT TO INSTALL NEW PIP SURFACE AND FENCE

AutoCAD SHX Text

EXTENTS OF ASPHALT PAVEMENT REMOVAL

AutoCAD SHX Text

TREE PROTECTION, (TYP)

AutoCAD SHX Text

AutoCAD SHX Text C530

AutoCAD SHX Text

REMOVE EXISTING PAVEMENT

AutoCAD SHX Text

PROPERTY LINE = PROJECT BOUNDARY/ WORK LIMITS

AutoCAD SHX Text

PROPERTY LINE = PROJECT BOUNDARY

AutoCAD SHX Text

FENCE LINE = PROJECT BOUNDARY/ WORK LIMITS

AutoCAD SHX Text

EXISTING BENCHES REMAIN, PROTECT

AutoCAD SHX Text

TREE PROTECTION FENCE, (TYP)

AutoCAD SHX Text

AutoCAD SHX Text C530

AutoCAD SHX Text

ALL EXISTING TREES REMAIN, CONTRACTOR TO PROTECT

AutoCAD SHX Text

PROPERTY LINE = PROJECT BOUNDARY/ WORK LIMITS

AutoCAD SHX Text

PROPERTY LINE = PROJECT BOUNDARY

AutoCAD SHX Text

FENCE LINE = PROJECT BOUNDARY/ WORK LIMITS

AutoCAD SHX Text EXISTING OVERHEAD POWER LINES, TELEPHONE-DATA LINES & UTILITY POLES REMAIN, PROTECT

AutoCAD SHX Text

EXISTING SIGN AND TIMBER GUIDERAIL REMAIN, PROTECT

AutoCAD SHX Text

EXISTING ASPHALT WALK REMAINS, PROTECT

AutoCAD SHX Text

EXISTING BASKETBALL COURT AND GOALS REMAIN, PROTECT

AutoCAD SHX Text EXISTING OVERHEAD POWER TRANSMISSION LINES AND POLES ON ADJACENT PROPERTY REMAIN. MAINTAIN CLEARANCE FROM TRANSMISSION INFRASTRUCTURE AT ALL TIMES.

AutoCAD SHX Text EXISTING OVERHEAD POWER TRANSMISSION LINES, POLES & GUYS ON ADJACENT PROPERTY. MAINTAIN CLEARANCE FROM TRANSMISSION INFRASTRUCTURE AT ALL TIMES.

AutoCAD SHX Text

EXISTING WATER LINES & STRUCTURES REMAIN, PROTECT

AutoCAD SHX Text

REMOVE EXISTING PLAY SURFACE

AutoCAD SHX Text

EXISTING TREES REMAIN

AutoCAD SHX Text

EXISTING SIGN REMAINS

AutoCAD SHX Text

REMOVE EXISTING WOOD FIBER MULCH SURFACE INCLUDING SUBBASE

AutoCAD SHX Text

EXISTING SIGN REMAINS

AutoCAD SHX Text EXISTING PLAY EQUIPMENT REMAINS - SWINGS AND PLAY STRUCTURE; PROTECT DURING CONSTRUCTION

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

EXISTING ASPHALT PAVEMENT & GRANITE CURBING REMAIN, PROTECT

AutoCAD SHX Text

ALL EXISTING TREES REMAIN, CONTRACTOR TO PROTECT

AutoCAD SHX Text EXISTING OVERHEAD POWER LINES, TELEPHONE-DATA LINES & UTILITY POLES REMAIN, PROTECT

AutoCAD SHX Text

EXISTING SIGN AND TIMBER GUIDERAIL REMAIN, PROTECT

AutoCAD SHX Text EXISTING OVERHEAD POWER TRANSMISSION LINES AND POLES ON ADJACENT PROPERTY REMAIN. MAINTAIN CLEARANCE FROM TRANSMISSION INFRASTRUCTURE AT ALL TIMES.

AutoCAD SHX Text EXISTING OVERHEAD POWER TRANSMISSION LINES, POLES & GUYS ON ADJACENT PROPERTY. MAINTAIN CLEARANCE FROM TRANSMISSION INFRASTRUCTURE AT ALL TIMES.

AutoCAD SHX Text

EXISTING WATER LINES & STRUCTURES REMAIN, PROTECT

AutoCAD SHX Text

EXISTING TREES REMAIN

AutoCAD SHX Text

TREE PROTECTION, (TYP)

AutoCAD SHX Text

AutoCAD SHX Text C530

AutoCAD SHX Text

EXISTING BASKETBALL GOALS REMAIN, PROTECT

AutoCAD SHX Text

CLEAN & PREPARE EXISTING ASPHALT PAVEMENT FOR RESURFACING

AutoCAD SHX Text

TREE PROTECTION FENCE, (TYP)

AutoCAD SHX Text

AutoCAD SHX Text C530

AutoCAD SHX Text

EXISTING ASPHALT WALK REMAINS, PROTECT

AutoCAD SHX Text

SAWCUT LINE & REMOVE EXISTING ASPHALT PAVEMENT FOR CLEAN EDGE TO MEET NEW WORK

AutoCAD SHX Text PRIOR TO ANY WORK ON THE PROJECT SITE THE CONTRACTOR SHALL COORDINATE WITH THE TOWN OF QUEENSBURY AND THE ADJACENT PROPERTY OWNER FOR ANY ACCESS AGREEMENTS THAT MAY BE REQUIRED

AutoCAD SHX Text

WORK LIMITS, (TYP)

AutoCAD SHX Text

WORK LIMITS, (TYP)

AutoCAD SHX Text

EXISTING BENCHES & SIGNS REMAIN, PROTECT

AutoCAD SHX Text

EXISTING FENCE REMAINS, PROTECT

AutoCAD SHX Text

EXISTING FENCE REMAINS, PROTECT

AutoCAD SHX Text

PREPARE EXISTING ASPHALT PAVEMENT

AutoCAD SHX Text

ALTERNATE WORK AREA

AutoCAD SHX Text

TEMPORARY SOIL STOCKPILE

AutoCAD SHX Text SOIL MATERIAL EXCAVATED TO INSTALL SITE IMPROVEMENTS SHALL BE LOADED, HAULED AWAY AND DISPOSED OF OFF-SITE IN A MANNER TO MINIMIZE SITE DISTURBANCE.

AutoCAD SHX Text SOIL MATERIAL EXCAVATED TO INSTALL SITE IMPROVEMENTS SHALL BE LOADED, HAULED AWAY AND DISPOSED OF OFF-SITE IN A MANNER TO MINIMIZE SITE DISTURBANCE.

CONTROL JOINT

CONSTRUCTION JOINT

EXPANSION JOINT

NOTES:PLAN

CONCRETE PAVEMENT

TOOLED EDGE

NOTES:

CONCRETE PAD

NOTES:

TEMPORARY SOIL STOCKPILE DETAIL

NOTES: SECTION

PERSPECTIVE VIEW

SILT FENCE INSTALLATION DETAIL

NOTES:

CONCRETE WASHOUT AREA

NOTE:

TREE PROTECTION FENCING DETAIL

PIP SAFETY SURFACE - EDGE AT ASPHALT PAVEMENT

NOTES:

NOTES:

POURED IN PLACE SAFETY SURFACE (PIP)

ASPHALT WALK DETAIL

NOTES:

SECTION - ABUTS PAVEMENT

SECTION - ABUTS LAWN

PIP SAFETY SURFACE -

FENCE INSTALLATION AT EDGE

PLAN VIEW

PROFILE

CONSTRUCTION ENTRANCE SPECIFICATIONS:

STABILIZED

CONSTRUCTION ACCESS DETAIL

C530

SITE DETAILS

RD/DC

DCM/JQ

Revisions

NO: DATE: DESCRIPTION:

1 08/19/2026 Addendum 1

DRAWING NAME:

8/

/2

1:

:2

PM

DRAWING NUMBER:

DATE:

ISSUED FOR:

DRAWN BY:

REVIEWED BY:

PROJECT NUMBER:

© 2024 LaBella Associates

B:

\G

LO

BA

L\ Pr oj ec ts \Q ue en sb ur y, T ow n of \2

W es t E nd

P ar k M as te r P la n De v\

_D ra w in gs \C iv il\

_C

0_

5_

SI

TE

D

ET

AI

L.

dw g

Town of Queensbury 742 Bay Road Queensbury, NY 12804

West End Park Improvements

117 Luzerne Road Queensbury, NY 12804

2241455

ISSUED FOR BID

JULY 31, 2026

It is a violation of New York Education Law Art. 145 Sec.

7209 & Art. 147 Sec. 7307, for any person, unless acting under the direction of a licensed architect, professional engineer, or land surveyor, to alter an item in any way. If an item bearing the seal of an architect, engineer, or land surveyor is altered; the altering architect, engineer, or land surveyor shall affix to the item their seal and notation

"altered by" followed by their signature and date of such alteration, and a specific description of the alteration.

4 British American Boulevard Latham, NY 12110 518-439-8235 labellapc.com

CERTIFICATE OF AUTHORIZATION NUMBER:

PROFESSIONAL ENGINEERING: 018281

LAND SURVEYING: 017976

GEOLOGICAL: 018750

PROJECT NAME:

CLIENT NAME:

E

S IO R

N o.

N

CEX E

T

O

F

E

S

T A

L

K

- 1

W Y

O R

R

M

A

.C

EAP

S C

G L

D O U

D

N AS

AL

C T

HC

O R D c C I

E T

EXP: 01/31/2027

AutoCAD SHX Text

1. MATERIAL AND METHODS OF CONSTRUCTION SHALL MATERIAL AND METHODS OF CONSTRUCTION SHALL BE IN CONFORMANCE WITH THE NEW YORK WITH THE NEW YORK STATE DEPARTMENT OF TRANSPORTATION (NYSDOT) STANDARD SPECIFICATIONS FOR CONSTRUCTION AND MATERIALS, DATED "CURRENT VERSION", AND ALL ADDENDA THERE TO. 2. ALL CONCRETE SHALL BE 4,500 CONCRETE. ALL CONCRETE SHALL BE 4,500 CONCRETE. 4,500 CONCRETE. CONCRETE. CONCRETE MATERIALS, PLACEMENT, AND CONSTRUCTION SHALL CONFORM WITH SECTION SECTION 500 OF THE ABOVE REFERENCED NYSDOT OF THE ABOVE REFERENCED NYSDOT STANDARD SPECIFICATIONS. 3. REINFORCING STEEL FOR CONCRETE SHALL REINFORCING STEEL FOR CONCRETE SHALL CONFORM WITH SECTION 556 - REINFORCING STEEL FOR CONCRETE STRUCTURES OF THE ABOVE REFERENCED NYSDOT STANDARD SPECIFICATIONS AND AS SPECIFICALLY CALLED OUT IN THE DRAWINGS. 4. ALL EXPOSED SURFACES SHALL HAVE A BROOM ALL EXPOSED SURFACES SHALL HAVE A BROOM TEXTURED FINISH & TOOLED EDGES. TOOL SHALL PROVIDE MAX 1-1/2" WIDE SMOOTH TROWEL FINISH AT JOINT. 5. EXPANSION JOINTS SHALL BE LOCATED A EXPANSION JOINTS SHALL BE LOCATED A MAXIMUM OF 20' ON CENTER, OR AS INDICATED ON PLANS. 6. JOINTS SHALL NOT BE SAW CUT. JOINTS SHALL NOT BE SAW CUT. 7. EXPOSED CONCRETE SURFACES SHALL BE EXPOSED CONCRETE SURFACES SHALL BE TREATED WITH "SUREBOND" 1100 RESIN-BASED, "SUREBOND" 1100 RESIN-BASED, WATER EMULSION CONCRETE CURING COMPOUND, , OR EQUAL. RATE AND METHOD OF APPLICATION SHALL BE IN ACCORDANCE WITH MANUFACTURER'S RECOMMENDATIONS. 8. SUBBASE MATERIAL SHALL CONFORM WITH SUBBASE MATERIAL SHALL CONFORM WITH SECTION 304 OF THE ABOVE REFERENCED NYSDOT OF THE ABOVE REFERENCED NYSDOT STANDARD. 9. WHERE IT IS NECESSARY TO PLACE FILL FOR WHERE IT IS NECESSARY TO PLACE FILL FOR PURPOSE OF BRINGING THE SUBGRADE ELEVATION UP TO A SPECIFIED GRADE, THE FILL MATERIAL PLACED SHALL BE IN ACCORDANCE WITH SECTION 203-EXCAVATION AND EMBANKMENT OF THE ABOVE REFERENCED NYSDOT STANDARD SPECIFICATIONS. 10. ALL WORK SHALL CONFORM WITH SECTION ALL WORK SHALL CONFORM WITH SECTION SECTION 608-SIDEWALK, DRIVEWAYS, AND BICYCLE PATHS -SIDEWALK, DRIVEWAYS, AND BICYCLE PATHS OF THE ABOVE REFERENCED NYSDOT STANDARD SPECIFICATIONS. 11. ALL WORK SHALL CONFORM WITH AASHTO ALL WORK SHALL CONFORM WITH AASHTO GEOMETRIC DESIGN OF HIGHWAYS AND STREET 2011, ICC A117.1 2009. OR LATEST EDITION. 12. SIDEWALK WIDTH SHOWN ON THE PLANS IS TO BE SIDEWALK WIDTH SHOWN ON THE PLANS IS TO BE MEASURED FROM THE BACK OF THE CURB. 13. SIDEWALKS SHALL HAVE A CROSS SLOPE OF 1.5% SIDEWALKS SHALL HAVE A CROSS SLOPE OF 1.5% 1.5% MAX. UNLESS OTHERWISE NOTED ON PLAN. 14. INSTALL EXPANSION JOINT WITH PREMOLDED INSTALL EXPANSION JOINT WITH PREMOLDED RESILIENT JOINT FILLER & SEALANT AT ALL EXISTING SIDEWALKS, CURBS, FIXED OBJECTS, ETC., INCLUDING THOSE PLACED ON PREVIOUS DAYS.

AutoCAD SHX Text X

AutoCAD SHX Text X

AutoCAD SHX Text X

AutoCAD SHX Text X

AutoCAD SHX Text X

AutoCAD SHX Text X

AutoCAD SHX Text X

AutoCAD SHX Text X

AutoCAD SHX Text X

AutoCAD SHX Text X

AutoCAD SHX Text X

AutoCAD SHX Text X

AutoCAD SHX Text X

AutoCAD SHX Text X

AutoCAD SHX Text X

AutoCAD SHX Text X

AutoCAD SHX Text X

AutoCAD SHX Text X

AutoCAD SHX Text X

AutoCAD SHX Text X

AutoCAD SHX Text X

AutoCAD SHX Text X

AutoCAD SHX Text X

AutoCAD SHX Text X

AutoCAD SHX Text

CONCRETE

AutoCAD SHX Text

CONCRETE

AutoCAD SHX Text

SCALE:

AutoCAD SHX Text C

AutoCAD SHX Text

AutoCAD SHX Text

NOT TO SCALE

AutoCAD SHX Text

6X6-W2.9XW2.9 W.W.F. (SEE NOTE NOTE 3)

AutoCAD SHX Text TOOLED JOINT 5' MAX O.C EACH WAY. OR AS SHOWN ON PLANS (1/4"R x 3/4"DEEP)

AutoCAD SHX Text COMPACTED SUBGRADE OR COMPACTED SELECT GRANULAR FILL AS REQUIRED TO BRING SUBGRADE TO CORRECT GRADE. (SEE NOTE NO. 9)

AutoCAD SHX Text

SEE NOTE 1414

AutoCAD SHX Text EXPANSION JOINT WITH PREMOLDED RESILIENT JOINT FILLER AND SEALANT 20' MAX O.C. OR AS INDICATED ON PLANS

AutoCAD SHX Text COMPACTED SUBGRADE OR COMPACTED SELECT GRANULAR FILL AS REQUIRED TO BRING SUBGRADE TO CORRECT GRADE. (SEE NOTE NO. 9)

AutoCAD SHX Text COMPACTED SUBGRADE OR COMPACTED SELECT GRANULAR FILL AS REQUIRED TO BRING SUBGRADE TO CORRECT GRADE. (SEE NOTE NO. 9)

AutoCAD SHX Text TOOLED EDGE (1/4"R x 3/4"DEEP)

AutoCAD SHX Text 6x6-W2.9xW2.9 W.W.F. (SEE NOTE 3)

AutoCAD SHX Text

1/4"R TOOLED EDGE TYPICAL

AutoCAD SHX Text

6X6-W2.9XW2.9 W.W.F. (SEE NOTE NOTE 3)

AutoCAD SHX Text

TOOLED EDGE WITH 1/4"R AND SEALER

AutoCAD SHX Text

1/4"R TYPICAL

AutoCAD SHX Text

BROOM-TEXTURED FINISH (TYP)

AutoCAD SHX Text 1/4"Rx3/4"DEEP TOOLED EDGE

AutoCAD SHX Text

CONTROL JOINTS

AutoCAD SHX Text

CONCRETE SIDEWALK

AutoCAD SHX Text

TYPICAL SPACING FOR EXPANSION JOINT

AutoCAD SHX Text C

AutoCAD SHX Text C

AutoCAD SHX Text

CONCRETE SIDEWALK

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

CONTROL JOINTS 5'MAX O.C. EACH WAY O.C. EACH WAY

AutoCAD SHX Text

EXISTING SIDEWALK OR FIXED OBJECT

AutoCAD SHX Text

SEE NOTE 1414

AutoCAD SHX Text

1. WHERE IT IS NECESSARY TO PLACE FILL FOR PURPOSE OF BRINGING THE WHERE IT IS NECESSARY TO PLACE FILL FOR PURPOSE OF BRINGING THE SUBGRADE ELEVATION UP TO A SPECIFIED GRADE, THE FILL MATERIAL PLACED SHALL BE IN CONFORMANCE WITH SECTION 203- EXCAVATION AND EMBANKMENT SECTION 203- EXCAVATION AND EMBANKMENT - EXCAVATION AND EMBANKMENT OF THE ABOVE REFERENCED NYSDOT STANDARD SPECIFICATIONS.

AutoCAD SHX Text 6x6-W2.9x2.9 WWF

AutoCAD SHX Text 6" OF 4,500 CONCRETE NYSDOT STANDARD OF 4,500 CONCRETE NYSDOT STANDARD 4,500 CONCRETE NYSDOT STANDARD CONCRETE NYSDOT STANDARD SPECIFICATIONS SECTIONS NO. 500 AND 608SECTIONS NO. 500 AND 608

AutoCAD SHX Text 12" COURSE OF NYSDOT SUBBASE COURSE COURSE OF NYSDOT SUBBASE COURSE TYPE 2 NYSDOT STANDARD SPECIFICATIONS SECTION 304. COMPACTED TO 95% MODIFIED . COMPACTED TO 95% MODIFIED PROCTOR

AutoCAD SHX Text GEOTEXTILE MIRAFI 140N FOR SUBGRADE STABILIZATION NYSDOT STANDARD SPECIFICATIONS SECTION 207SECTION 207

AutoCAD SHX Text COMPACTED SUBGRADE OR COMPACTED SELECT GRANULAR FILL AS REQUIRED TO BRING SUBBASE TO CORRECT GRADE. SEE NOTE.

AutoCAD SHX Text

3" MIN

AutoCAD SHX Text

6" MIN

AutoCAD SHX Text

SCALE:

AutoCAD SHX Text C

AutoCAD SHX Text

AutoCAD SHX Text

NOT TO SCALE

AutoCAD SHX Text

MIN. SLOPE

AutoCAD SHX Text

MIN. SLOPE

AutoCAD SHX Text

SLOPE OR LESS

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

1. AREA CHOSEN FOR STOCKPILING OPERATIONS SHALL BE DRY AND STABLE. 2. MAXIMUM SLOPE OF STOCKPILE SHALL BE 1V:2H. MAXIMUM SLOPE OF STOCKPILE SHALL BE 1V:2H. 3. UPON COMPLETION OF SOIL STOCKPILING, EACH PILE SHALL UPON COMPLETION OF SOIL STOCKPILING, EACH PILE SHALL BE SURROUNDED WITH SILT FENCING, THEN STABILIZED WITH VEGETATION OR COVERED. 4. SEE SPECIFICATIONS FOR INSTALLATION OF SILT FENCE.SEE SPECIFICATIONS FOR INSTALLATION OF SILT FENCE.

AutoCAD SHX Text

AutoCAD SHX Text C530

AutoCAD SHX Text

SCALE:

AutoCAD SHX Text C

AutoCAD SHX Text

AutoCAD SHX Text

NOT TO SCALE

AutoCAD SHX Text

SILT FENCE

AutoCAD SHX Text

AutoCAD SHX Text

1. WOVEN WIRE FENCE TO BE FASTENED SECURELY TO FENCE POSTS WITH WIRE TIES WOVEN WIRE FENCE TO BE FASTENED SECURELY TO FENCE POSTS WITH WIRE TIES OR STAPLES. POSTS SHALL BE STEEL "T" OR "U" TYPE OR HARDWOOD. 2. FILTER FABRIC TO BE FASTENED SECURELY TO WOVEN WIRE FENCE WITH TIES FILTER FABRIC TO BE FASTENED SECURELY TO WOVEN WIRE FENCE WITH TIES SPACED EVERY 24" AT TOP AND MID SECTION. FENCE SHALL BE WOVEN WIRE, 6" MAX MESH OPENING. 3. WHEN TWO SECTIONS OF FILTER FABRIC ADJOIN EACH OTHER THEY SHALL BE WHEN TWO SECTIONS OF FILTER FABRIC ADJOIN EACH OTHER THEY SHALL BE OVERLAPPED BY 6" AND FOLDED. 4. MAINTENANCE SHALL BE PERFORMED AS NEEDED AND MATERIALS REMOVED WHEN MAINTENANCE SHALL BE PERFORMED AS NEEDED AND MATERIALS REMOVED WHEN "BULGES" DEVELOP IN THE SILT FENCE. 5. MAXIMUM DRAINAGE AREA FOR OVERLAND FLOW TO A SILT FENCE SHALL NOT MAXIMUM DRAINAGE AREA FOR OVERLAND FLOW TO A SILT FENCE SHALL NOT EXCEED 1/4 ACRE PER 100 FEET OF FENCE. 6. SILT FENCE SHALL BE USED WHERE EROSION COULD OCCUR IN THE FORM OF SILT FENCE SHALL BE USED WHERE EROSION COULD OCCUR IN THE FORM OF SHEET EROSION. 7. SILT FENCE SHALL NOT BE USED WHEN A CONCENTRATION OF WATER IS FLOWING SILT FENCE SHALL NOT BE USED WHEN A CONCENTRATION OF WATER IS FLOWING TO THE BARRIER. 8. MAXIMUM ALLOWABLE SLOPE LENGTHS CONTRIBUTING RUN-OFF TO A SILT FENCE MAXIMUM ALLOWABLE SLOPE LENGTHS CONTRIBUTING RUN-OFF TO A SILT FENCE ARE: SLOPE STEEPNESS MAXIMUM SLOPE LENGTH(FT) 2:1 25 3:1 50 4:1 75 5:1 OR FLATTER 100

AutoCAD SHX Text

EMBED FILTER FABRIC MIN 6" INTO GROUND

AutoCAD SHX Text 20"

AutoCAD SHX Text 20"

AutoCAD SHX Text

MIN.

AutoCAD SHX Text 16"

AutoCAD SHX Text 16"

AutoCAD SHX Text

MIN.

AutoCAD SHX Text

10'MAX CENTER TO CENTER

AutoCAD SHX Text

6" MIN

AutoCAD SHX Text

FLOW

AutoCAD SHX Text

SCALE:

AutoCAD SHX Text C

AutoCAD SHX Text

AutoCAD SHX Text

NOT TO SCALE

AutoCAD SHX Text

36" MIN FENCE POST

AutoCAD SHX Text MIRAFI 100X PREFABRICATED PREFABRICATED SILT FENCE WITH POSTS OR APPROVED EQUIVALENT

AutoCAD SHX Text

WOVEN WIRE FENCE (MIN. 14 GAUGE W/ MAX. 6" MESH SPACING)

AutoCAD SHX Text

36" MIN FENCE POSTS, DRIVEN MIN 16" INTO GROUND

AutoCAD SHX Text

UNDISTURBED GROUND

AutoCAD SHX Text

TAMPED BACKFILL

AutoCAD SHX Text

EXCAVATED TRENCH

AutoCAD SHX Text

FLOW

AutoCAD SHX Text

10' MIN.

AutoCAD SHX Text

10' MIN.

AutoCAD SHX Text 30"±

AutoCAD SHX Text

AGGREGATE

AutoCAD SHX Text

TRUCKS

AutoCAD SHX Text

ALL CONCRETE

AutoCAD SHX Text

WASHOUT HERE

AutoCAD SHX Text

SHALL

AutoCAD SHX Text 18"

AutoCAD SHX Text 12"

AutoCAD SHX Text

SIGN SHALL BE PLACED

AutoCAD SHX Text

IN A PROMINENT LOCATION

AutoCAD SHX Text

AT WASHOUT AREA

AutoCAD SHX Text

%%UTYPICAL SECTION

AutoCAD SHX Text

%%UPLAN

AutoCAD SHX Text

%%UWASHOUT SIGN

AutoCAD SHX Text

12" MIN

AutoCAD SHX Text

1. CONTAINMENT MUST BE STRUCTURALLY SOUND CONTAINMENT MUST BE STRUCTURALLY SOUND AND LEAK FREE AND CONTAIN ALL LIQUID WASTES. 2. CONTAINMENT DEVICES MUST BE OF SUFFICIENT CONTAINMENT DEVICES MUST BE OF SUFFICIENT QUANTITY OR VOLUME TO COMPLETELY CONTAIN THE LIQUID WASTES GENERATED. 3. WASHOUT MUST BE CLEANED OR NEW WASHOUT MUST BE CLEANED OR NEW FACILITIES CONSTRUCTED AND READY TO USE ONCE WASHOUT IS 75% FULL. THIS INCLUDES REPLACEMENT OF THE 10 MIL POLYETHLENE SHEETING.

AutoCAD SHX Text

4. WASHOUT AREA(S) SHALL BE INSTALLED IN A WASHOUT AREA(S) SHALL BE INSTALLED IN A LOCATION EASILY ACCESSIBLE BY CONCRETE TRUCKS. 5. ONE OR MORE AREAS MAY BE INSTALLED ON ONE OR MORE AREAS MAY BE INSTALLED ON THE CONSTRUCTION SITE AND MAY BE RELOCATED AS CONSTRUCTION PROGRESSES. 6. AT LEAST WEEKLY, REMOVE ACCUMULATION OF AT LEAST WEEKLY, REMOVE ACCUMULATION OF SAND AND AGGREGATE AND DISPOSE OF PROPERLY.

AutoCAD SHX Text

SEASONAL HIGH GROUNDWATER TABLE

AutoCAD SHX Text

SCALE:

AutoCAD SHX Text C

AutoCAD SHX Text

AutoCAD SHX Text

NOT TO SCALE

AutoCAD SHX Text

10 MIL POLYETHYLENE SHEETING

AutoCAD SHX Text ANCHOR BALES WITH (2) 2"x2"x4' STAKES PER BALE

AutoCAD SHX Text

BALES TO BUTT

AutoCAD SHX Text

BLACK LETTERS ON WHITE BACKGROUND

AutoCAD SHX Text

GALVANIZED "U" CHANNEL POST

AutoCAD SHX Text

FINISH GRADE

AutoCAD SHX Text

EXISTING GRADE

AutoCAD SHX Text

6" MIN EMBEDMENT (TYPICAL)

AutoCAD SHX Text

WOOD STAKE (TYPICAL)

AutoCAD SHX Text

10 MIL POLYETHYLENE SHEETING

AutoCAD SHX Text

STRAW BALE (TYPICAL)

AutoCAD SHX Text

BINDING WIRE

AutoCAD SHX Text

6" MIN DEPTH AGGREGATE ALL AROUND

AutoCAD SHX Text

36" MIN.

AutoCAD SHX Text

%%USECTIONAL ELEVATION

AutoCAD SHX Text

30" MIN.

AutoCAD SHX Text

EXISTING GRADE

AutoCAD SHX Text

%%UPLAN

AutoCAD SHX Text

SEE LANDSCAPING PLAN FOR ADDITIONAL TREE PROTECTION NOTES.

AutoCAD SHX Text

METAL FENCE POST

AutoCAD SHX Text

ORANGE CONSTRUCTION FENCING SECURELY FASTENED TO POSTS (TYP.)

AutoCAD SHX Text

DRIVE POSTS MIN. 30" IN GROUND

AutoCAD SHX Text

DRIP LINE OF TREE

AutoCAD SHX Text

SCALE:

AutoCAD SHX Text R

AutoCAD SHX Text

AutoCAD SHX Text

NOT TO SCALE

AutoCAD SHX Text

SCALE:

AutoCAD SHX Text R

AutoCAD SHX Text

AutoCAD SHX Text

NOT TO SCALE

AutoCAD SHX Text

1. POURED IN PLACE SURFACE STANDARD OF QUALITY = "NO FAULT POURED IN PLACE SURFACE STANDARD OF QUALITY = "NO FAULT SAFETY EPDM SURFACING" OR APPROVED EQUAL 2. COLOR: EQUAL MIX TAN, GREEN & BLACKCOLOR: EQUAL MIX TAN, GREEN & BLACK

AutoCAD SHX Text

12" MIN. POURED IN PLACE EPDM WEAR SURFACE

AutoCAD SHX Text

ADJACENT ASPHALT

AutoCAD SHX Text

3.75" MIN. POURED IN PLACE IMPACT LAYER

AutoCAD SHX Text

6" COURSE OF SUBBASE COURSE TYPE 2, COMPACTED TO 95% MODIFIED PROCTOR

AutoCAD SHX Text

STABLIZATION FABRIC

AutoCAD SHX Text COMPACTED SUBGRADE OR COMPACTED SELECT GRANULAR FILL AS REQUIRED TO BRING SUBBASE TO CORRECT GRADE

AutoCAD SHX Text

SAWCUT CLEAN EDGE IN ASPHALT

AutoCAD SHX Text COMPACTED SUBGRADE OR COMPACTED SELECT GRANULAR FILL AS REQUIRED TO BRING SUBBASE TO CORRECT GRADE.

AutoCAD SHX Text 12"

AutoCAD SHX Text 6"

AutoCAD SHX Text

STABILIZATION FABRIC

AutoCAD SHX Text 6" COURSE OF SUBBASE COURSE OF SUBBASE COURSE TYPE 2. COMPACTED TO 95% MODIFIED PROCTOR

AutoCAD SHX Text

3 " POURED IN PLACE IMPACT LAYER12" POURED IN PLACE IMPACT LAYER

AutoCAD SHX Text

12" POURED IN PLACE EPDM WEAR SURFACE

AutoCAD SHX Text

1. POURED IN PLACE SURFACE STANDARD OF QUALITY = "NO FAULT POURED IN PLACE SURFACE STANDARD OF QUALITY = "NO FAULT SAFETY EPDM SURFACING" OR APPROVED EQUAL 2.