20Q0050_ RFQ_I.pdf

To: Prospective Offerers

Embassy of the United States of America

Lima, Peru

July 21, 2020

Subject: RFQ 19PES020Q00S0 - Preventive Maintenance of Chillers

Enclosed is a Request for Quotation for Preventive Maintenance of the Chillers of the U.S. Embassy in Lima, Peru. If you would like to submit a quotation, follow the instructions in Section 3 of the solicitation, complete the required portions of the attached document, and submit it to the address shown below.

Questions in English can be submitted to rivascr@state.gov until August 4, 2020 by COB. Responses will be publicized in the Governement Point of Entry, Beta SAM by August 7, 2020.

For a proposal to be considered, you must complete and submit the following:

Volume 1:

SF-1449

Section 1 - Price

Volume 2:

Section 3 - Information as requested under Solicitation Provisions

Section 5 -Representations and Certifications including proof of a Defense Base Act insurance

(DBA)and an active registration in the System for Award Management (SAM)

The U.S. Government intends to award a contract to the responsible company submitting an acceptable quotation at the lowest price. We intend to award a contract based on initial quotations, without holding discussions, although we may hold discussions with companies in the competitive range if there is a need to do so.

Your proposal must be submitted by email, with the RFQ number in the subject, to Mr. Paul Kopecki, Contracting Officer, KopeckiP@state.gov and Mr. Christian Rivas, RivasCR@state.gov , on or before 10:00 a.m. on August 21, 2020, (local date and time). No quotations will be accepted after this date and time.

Paul Kopecki

Contracting Officer

Enclosure: As Stated

TABLE OF CONTENTS

Section 1 - The Schedule

SF 1449 cover sheet

Continuation To SF-1449, RFQ Number 19PE5020Q0050, Prices, Block 23

Continuation To SF-1449, RFQ Number 19PE5020Q0050, Schedule Of Supplies/Services, Block 20 Performance Work Statement

Section 2 - Contract Clauses

Contract Clauses

Addendum to Contract Clauses - FAR and DOSAR Clauses not Prescribed in Part 12

Section 3 - Solicitation Provisions

Solicitation Provisions

Addendum to Solicitation Provisions - FAR and DOSAR Provisions not Prescribed in Part 12

Section 4 - Evaluation Factors

Evaluation Factors

Addendum to Evaluation Factors - FAR and DOSAR Provisions not Prescribed in Part

Section 5 - Representations and Certifications

Offeror Representations and Certifications

Addendum to Offeror Representations and Certifications - FAR and DOSAR Provisions not Prescribed in Part 12

AUTORIZED FOR LOCAL REPRODUCTION STANDARD FORM 1449 (REV. 02/2012)

PREVIOUS EDITION IS NOT USABLE Computer Generated Prescribed by GSA - FAR (48 CFR) 53.212

SOLICITATION/CONTRACT/ORDER FOR COMMERCIAL ITEMS

OFFEROR TO COMPLETE BLOCKS 12, 17, 23, 24, & 30

1. REQUISITION NUMBER

PR9211206

PAGE 1 OF 455 PAGES

2. CONTRACT NO. 3. AWARD/ EFFECTIVE

DATE

4. ORDER NUMBER 5. SOLICITATION NUMBER

19PE5020Q0050

6. SOLICITATION ISSUE DATE

07/21/2020

7. FOR SOLICITATION

INFORMATION CALL:

a. NAME Christian R Rivas

b. TELEPHONE NUMBER(No collect calls)

(511) 618-2192

8. OFFER DUE DATE/ LOCAL TIME

08/21/2020 / 10:00 hrs

9. ISSUED BY CODE PE500 10. THIS ACQUISITION IS X UNRESTRICTED OR SET ASIDE: % FOR:

SMALL BUSINESS WOMEN-OWNED SMALL BUSINESS

HUBZONE SMALL

BUSINESS

(WOSB) ELLIGIBLE UNDER THE WOMEN-OWNED

SMALL BUSINESS PROGRAM NAICS:

EDWOSB EMERGING SMALL BUSINESS

AMERICAN EMBASSY LIMA

Ave. Lima Polo Cdra 2 Monterrico ATTN: GSO/Procurement Lima

PERU

SERVICE-DISABLED

VETERAN-OWNED

SMALL BUSINESS 8 (A) SIZE STANDARD:

13b. RATING11. DELIVERY FOR FOB DESTINAT-

TION UNLESS BLOCK IS

MARKED

SEE SCHEDULE

12. DISCOUNT TERMS 13a. THIS CONTRACT IS A

RATED ORDER UNDER

DPAS (15 CFR 700)

14. METHOD OF SOLICITATION

RFQ IFB RFP

15. DELIVER TO CODE 16. ADMINISTERED BY CODE

AMERICAN EMBASSY LIMA

Ave. Lima Polo Cdra 2 Monterrico ATTN: GSO/Procurement Lima

PERU

AMERICAN EMBASSY LIMA

Ave. Lima Polo Cdra 2 Monterrico ATTN: GSO/Procurement Lima

PERU

CODE FACILITY

CODE

17a. CONTRACTOR/

OFFERER

TELEPHONE NO.

18a. PAYMENT WILL BE MADE BY

AMERICAN EMBASSY LIMA

Ave. Lima Polo Cdra 2 Monterrico ATTN: Financial Management Office (FMO) Lima

PERU

CODE

17b. CHECK IF REMITTANCE IS DIFFERENT AND PUT SUCH ADDRESS IN

OFFER

18b. SUBMIT INVOICES TO ADDRESS SHOWN IN BLOCK 18a UNLESS BLOCK

BELOW IS CHECKED SEE ADDENDUM

19.

ITEM NO.

20.

SCHEDULE OF SUPPLIES/SERVICES

21.

QUANTITY

22.

UNIT

23.

UNIT PRICE

24.

AMOUNT

(Use Reverse and/or Attach Additional Sheets as Necessary)

25. ACCOUNTING AND APPROPRIATION DATA 26. TOTAL AWARD AMOUNT (For Govt. Use Only)

27a.SOLICITATION INCORPORATES BY REFERENCE FAR 52.212-1, 52.212-4. FAR 52.212-3 AND 52.212-5 ARE ATTACHED. ADDENDA ARE ARE NOT ATTACHED

27b.CONTRACT/PURCHASE ORDER INCORPORATES BY REFERENCE FAR 52.212-4. FAR 52.212-5 IS ATTACHED. ADDENDA ARE ARE NOT ATTACHED

28. CONTRACTOR IS REQUIRED TO SIGN THIS DOCUMENT AND RETURN _ __ COPIES

TO ISSUING OFFICE. CONTRACTOR AGREES TO FURNISH AND DELIVER ALL ITEMS

SET FORTH OR OTHERWISE IDENTIFIED ABOVE AND ON ANY ADDITIONAL SHEETS

SUBJECT TO THE TERMS AND CONDITIONS SPECIFIED HEREIN.

29. AWARD OF CONTRACT: REF. _ _______________ OFFER DATED

_ __________. YOUR OFFER ON SOLICITATION (BLOCK 5), INCLUDING ANY

ADDITIONS OR CHANGES WHICH ARE SET FORTH HEREIN, IS ACCEPTED AS

TO ITEMS:

30a. SIGNATURE OF OFFEROR/CONTRACTOR 31a. UNITED STATES OF AMERICA (SIGNATURE OF CONTRACTING OFFICER)

30b. NAME AND TITLE OF SIGNER (Type or print) 30c. DATE SIGNED 31b. NAME OF CONTRACTING OFFICER (Type or print) 31c. DATE SIGNED

X

X X

ITEM NO. 20.

SCHEDULE OF SUPPLIES/SERVICES

21.

QUANTITY

22.

UNIT

23.

UNIT PRICE

24.

AMOUNT

32a. QUANTITY IN COLUMN 21 HAS BEEN

RECEIVED INSPECTED ACCEPTED, AND CONFORMS TO THE CONTRACT, EXCEPT AS NOTED: _______________________________

32b. SIGNATURE OF AUTHORIZED GOVERNMENT

REPRESENTATIVE

32c. DATE 32d. PRINTED NAME AND TITLE OF AUTHORIZED GOVERNMENT

REPRESENTATIVE

32e. MAILING ADDRESS OF AUTHORIZED GOVERNMENT REPRESENTATIVE 32f. TELEPHONE NUMBER OF AUTHORIZED GOVERNMENT REPRESENTATIVE

32g. E-MAIL OF AUTHORIZED GOVERNMENT REPRESENTATIVE

33. SHIP NUMBER 34. VOUCHER NUMBER 35. AMOUNT VERIFIED

CORRECT FOR

36. PAYMENT 37. CHECK NUMBER

PARTIAL FINAL COMPLETE PARTIAL FINAL

38. S/R ACCOUNT NO. 39. S/R VOUCHER NO. 40. PAID BY

41.a. I CERTIFY THIS ACCOUNT IS CORRECT AND PROPER FOR PAYMENT 42a. RECEIVED BY (Print) 41b. SIGNATURE AND TITLE OF CERTIFYING OFFICER 41C. DATE

42b. RECEIVED AT (Location)

42c. DATE REC’D (YY/MM/DD) 42d. TOTAL CONTAINERS

STANDARD FORM 1449 (REV. 2/2012) BACK

Solicitation to provide annual preventive maintenance service to the Embassy Chillers according to the attached Statement of Work and related documents.

The Period of Performance is for a base year and three (3) one-year options.

1 all

2 | P a g e

SECTION 1 - THE SCHEDULE

CONTINUATION TO SF-1449

RFQ NUMBER 19PE5020Q0050

PRICES, BLOCK 23

1. SCOPE OF SERVICES

The Contractor shall provide services for the Preventive Maintenance of the two (02) Water Cooled Centrifugal Chillers and two (02) Air Cooled screw Chillers located in the Chancery and Annex buildings respectively within the U.S. Embassy premises in Lima in accordance with the Performance Work Statement and the attachments contained in this document.

The price listed below shall include all labor, materials, overhead, profit and applicable taxes. In consideration of satisfactory performance of all schedule services required under this contract, the contractor shall be paid a firm fixed-price for all services.

The Contractor shall provide the services for the base period of the contract at the rates shown in paragraph 3 and any option years exercised by the Government.

2. PERIOD OF PERFORMANCE

a) The performance period of this contract is from the start date in the Notice to Proceed and continuing for 12 months, with 3 (three) one-year options to renew. The initial period of performance includes any transition period authorized under the contract.

b) The Government may extend this contract for up to three (3) additional 12-month periods in accordance with the option clause in Section II. 52.217-9, Option to Extend the Term of the Contract, which also specifies the total duration of this contract. See also Section II, FAR 52.217- 8, Option to Extend Services, for up to an additional six months of optional performance, if required by the Government.

3. PRICING

3.1 The Contractor shall provide professional services, labor and materials on a firm fixed-price in US Dollars.

3.2 The Contractor shall furnish all equipment, supervision, labor, supplies, services and materials necessary comply with the Performance Work Statement. All work shall be performed in accordance with these specifications and subject to the terms and conditions of this contract.

3 | P a g e

3.3 The rates below include all costs associated with providing preventive maintenance services in accordance with the attached scope of work, and the manufacturer’s warranty including materials, labor, insurance (see FAR 52.228-3 and 52.228-5), overhead, profit and GST (if applicable).

The Contractor shall provide one (1) service during a period of 12 months.

Base year:

Option Year 1:

CLIN Description Quantity of Equipment

Type of services

No. of service

Unit price / service ($)

Total per year

Trane CVHE250 Centrifugal Chillers

02 Annual 01

Trane RTAC 140 Screw Chillers

02 Annual 01

Tech. check reports & Permits

04 Annual 01

Total Base Year

Equipment

Type of services

No. of service

Unit price / service

Total per year

Trane CVHE250 Centrifugal Chillers

02 Annual 01

Trane RTAC 140 Screw Chillers

02 Annual 01

Tech. check reports & Permits

Annual

Total Option Year 1

4 | P a g e

Option Year 2:

Option Year 3:

Gran Total Contract Price plus All option years (including IGV Tax, if applicable)

Base Year Total USD

Option Year 1 Total USD

Option Year 2 Total USD

Option Year 3 Total USD

Grand Total of Base plus All Option Years USD

Equipment

Type of services

No. of service

Unit price / service ($)

Total per year ($)

Trane CVHE250 Centrifugal Chillers

02 Annual 01

Trane RTAC 140 Screw Chillers

02 Annual 01

Tech. check reports &

Total Option Year 2

Equipment

Type of services

No. of service

Unit price / service ($)

Total per year

Trane CVHE250 Centrifugal Chillers

02 Annual 01

Trane RTAC 140 Screw Chillers

02 Annual 01

Tech. check reports &

Total Option Year 3

5 | P a g e

4. VALUE ADDED TAX

Value Added Tax (VAT) is not included in the CLIN rates. Instead, it will be priced as a separate Line Item in the contract and on Invoices. Local law dictates the portion of the contract price that is subject to VAT; this percentage is multiplied only against that portion. It is reflected for each performance period.

6 | P a g e

CONTINUATION TO SF-1449,

RFQ NUMBER 19PE5020Q0050

SCHEDULE OF SUPPLIES/SERVICES, BLOCK 20

PERFORMANCE WORK STATEMENT

1. DESCRIPTION

The US Embassy in Lima requires preventive maintenance services for the two (02) Chancery Water Cooled Centrifugal Chillers and two (02) Annex Air Cooled screw Chillers. These services shall result in all systems being serviced under this agreement being in good operational condition when activated.

1.1. The US Embassy Lima requires the Contractor to maintain the following equipment in a safe, reliable and efficient operating condition. Please see equipment list included in Exhibit A for a more detailed description.

1. Water Cooled Centrifugal Chillers Quantity: 02 each Manufacturer: Trane Model: CVHE250 Serial: L17E02736 & L17E02737 Rated Capacity: 187 TON Location: Room B-33 Chancery Basement

2. Air Cooled Screw Chillers

Manufacturer: Trane Model: RTAC-140 Serial: U19D03341 & U19D03342 Rated Capacity: 140.2 TON Location: Annex Building Penthouse

1.2. The Contractor shall provide all necessary managerial, administrative and direct labor personnel, as well as all transportation, equipment, tools, supplies and materials required to perform inspection, maintenance, and component replacement as required to maintain the systems in accordance with this work statement. Under this Contract the Contractor shall provide the services of trained and qualified technicians to inspect, adjust, and perform scheduled preventive maintenance.

7 | P a g e

1.3. Performance Standards: The chillers shall be clean and in good operating condition upon completion of the service. The preventive maintenance service shall result in the parts of the system serviced being in a condition to operate efficiently and effectively.

2. HOURS OF PERFORMANCE

2.1. The Contractor shall maintain work schedules. The Contractor shall deliver standard services between the hours of 8:00AM and 5:00 PM Monday through Friday. Other works that because of its nature and may cause inconveniences for the occupants of the Mission, shall be done on the same hours, on weekends.

2.2. Contractor must follow all working safety regulations and provide their personnel with appropriate safety equipment like gloves, security shoes, ocular protection, earring protection, falling protection etc... A site meeting will be held to discuss safety issues prior to work commencing.

2.3. Please note that all regulations indicated in the manual USCOE EM-385 Safety Manual which apply to this work, shall be adhered to and followed by all Contractor personnel.

https://www.publications.usace.army.mil/Portals/76/Publications/EngineerManuals/EM_385- 1-1.pdf

2.4. Works shall be done in one chiller of each type at the time avoiding Summer time when both chillers are required for Embassy operations.

2.5. Works shall be done and completed, between July and November, when only one chiller is required to run activities for the Embassy.

3. SCHEDULED PREVENTIVE MAINTENANCE

3.1. General

3.1.1. The Contractor shall perform preventive maintenance as outlined in Exhibit A - STATEMENT OF WORK. The objective of scheduled preventive maintenance is to eliminate system malfunction, breakdown and deterioration when units are activated/running.

3.1.2. The Contractor shall inventory, supply and replace expendable parts (eg, filters, belts, hoses, gaskets) that have become worn due to wear and tear. The Contractor shall maintain a supply of expendable and common parts on site so that these are readily available for normal maintenance to include: hoses, belts, oil, chemicals, coolant, filters (Air, Fuel, Oil), grease, sealant, thermostat, fuses; in addition to the appropriate tools, testing equipment, safety shoes and apparel for technicians, personal protective equipment (hands, hearing, eye protection), MSDS, cleaning material and oil spill containment kits. The contractor shall inventory the supply after each visit and order replacement supplies and have them delivered on site. Maintenance https://www.publications.usace.army.mil/Portals/76/Publications/EngineerManuals/EM_385-1-1.pdf https://www.publications.usace.army.mil/Portals/76/Publications/EngineerManuals/EM_385-1-1.pdf

8 | P a g e materials shall be unused and are to be industry standard and intended for the task to be performed. Parts shall be OEM approved. Refrigerants shall meet the AHRI Standard 700-2015 or most recent AHRI Standards.

3.1.3. Refrigerants, parts and maintenance materials delivered to the post are to be new and unused. Reclaimed refrigerants are not to be delivered to Posts. Reclaimed refrigerants within post compounds are to be retained and stored and may be used if not contaminated. Refrigerants shall be stored in containers clearly indicating the refrigerant type.

3.1.4. Exclusion. This contract does NOT include repair of equipment and replacement of hardware (e.g. bearings, pistons, piston rings, crankshaft, gears.) Hardware replacements will be separately priced out by the Contractor for the Government’s approval and acceptance. The Government has the option to accept or reject the Contractor’s quote for parts and reserves the right to obtain similar spare parts from other competitive sources. If required by the Government, the Contractor shall utilize Government-purchased spare parts, if awarded the work. Such repairs/replacements will be accomplished by a separate purchase order. However, this exclusion does not apply if the repair is to correct damage caused by Contractor negligence.

3.1.5. Replacement/repair of any electronic or electrical parts shall be approved by the Embassy prior to installation of the part.

3.1.6. Stocking of recommended repair parts is at the discretion of the Facility Manager and is dependent upon the nearest location of the Equipment manufacturer, distributor or dealer. A recommended spare parts list shall be obtained by the Contractor from the manufacturer or distributor and provided to the Facility Manager to procure.

3.2. Checklist Approval

The Contractor shall submit to the COR a schedule and description of preventive maintenance tasks which the Contractor plans to perform. The Contractor shall prepare this schedule and task description in a checklist format for the COR’s approval prior to contract work commencement.

3.2.1. The Contractor shall provide trained technicians to perform the service at frequencies stated in Exhibit A and on the equipment called out in this SOW. The technician shall sign off on every item of the checklist and leave a copy of this signed checklist with the COR or the COR's designate after each maintenance visit.

3.2.2. It is the responsibility of the Contractor to perform all manufacturers’ recommended preventive maintenance including preventive maintenance recommended by the manufacturers’ technical manuals for the respective equipment.

3.2.3 Additionally, the maintenance contractor shall obtain and keep at the post O&M binders provided by the manufacturers. These binders shall be placed in a location accessible to post personnel to review as needed.

9 | P a g e

4. PERSONNEL, TOOLS, CONSUMABLE MATERIALS AND SUPPLIES

The Contractor shall provide trained technicians with the appropriate tools and testing equipment for scheduled maintenance, safety inspection, and safety testing as required by this Contract. The Contractor shall provide all of the necessary materials and supplies to maintain, service, inspect and test all the systems to be maintained.

4.1. Contractor furnished materials include but are not limited to appropriate tools, testing equipment, safety shoes and apparel for technicians, hands, hearing and eye protection, MSDS, cleaning material and oil spill containment kit. Expendable/consumable items (e.g. hoses, belts, oil, chemicals, coolant, filters (Air, Fuel, Oil), generator starting batteries, grease, sealant, thermostat, fuse), shall be maintained in the onsite inventory.

4.2. Repairs are not included in this contract.

4.3. Disposal of used oil, fuel, battery and other toxic substances. The Contractor is responsible for proper disposal of toxic/hazardous substances. All material shall be disposed of according to Government and Local law. After proper disposal the contractor must show proof of authorized disposal of these toxic/hazardous substances.

5. SOFTWARE, LICENSES AND PASSWORDS

Copies of any and all software and licenses needed to control or to adjust the communications module shall be given to the post upon completion of the work.

6. DELIVERABLES

Provide a written report in English to Post Facilities Manager containing following:

a) System information (make, model, all devices types)

b) Pass/Fail of each feature and type of component tested. If a device fails, note device type, address and location within Post

c) Any comments on system (or device) condition pertaining to service life and dependability.

d) Full printout of test from system printer

e) Contractor must record all visits in Contractor Visitors Log at FAC Office

10 | P a g e

EXHIBIT A

Statement of Work

I. GENERAL INFORMATION:

The United States Embassy in Lima requires professional services and contractor cost proposals to perform preventive maintenance services of the facility’s Trane Centrifugal Water Cooled Chillers and Trane Air Cooled Screw Chillers

II. PROJECT REQUIREMENTS:

DESCRIPTION OF EQUIPMENT:

Water Cooled Centrifugal Chillers

Manufacturer: Trane Model: CVHE250 Serial: L17E02736 & L17E02737 Rated Capacity: 187 TON Location: Room B-33 Chancery Basement

Air Cooled Screw Chillers

Manufacturer: Trane Model: RTAC-140 Serial: U19D03341 & U19D03342 Rated Capacity: 140.2 TON Location: Annex Building Penthouse

III. GENERAL REQUIREMENTS:

The Contractor under this SOW shall be responsible for labor, tools, and materials required to carry out all preventive maintenance as outlined in this SOW. The Government provides the following documents:

Water Cooled Centrifugal Chillers

Attachment 1: CVHE-SVX02K-EN Installation, Operation and Maintenance Manual

Attachment 2: CVHE250 Parts List

11 | P a g e

Attachment 3: EarthWise™ Purge System with Tracer AdaptiView™ Control for Water-Cooled CenTraVac™ Chillers (PRGD-SVX01*-EN).

Attachment 4: CVHE250 Submittal

Attachment 5: RTAC 140 Installation, Operation & Maintenance

Attachment 6: RTAC 140 Parts List

Attachment 7: RTAC-140 Chiller Submittal

IV. SCOPE OF WORK - - CHILLERS MAINTENANCE

Contractor shall provide all materials, supervision, labor, tools and equipment to perform preventive maintenance. All personnel working in the vicinity shall wear and /or use safety protection while all work is performed. Any questions or injuries shall be brought to the attention of the Post Occupation Safety and Health Officer (POSHO) immediately. Material Safety Data Sheets (MSDS) shall be provided by the Contractor for all HAZMAT materials. Copies shall be provided to the Embassy for approval.

The Contractor shall inventory, supply and replace expendable parts (e.g., filters, belts, hoses, gaskets) that have become worn down due to wear and tear. The Contractor shall maintain a supply of expendable and common parts on site so that these are readily available for normal maintenance to include: hoses, belts, oil, chemicals, coolant, filters (Air, Fuel, Oil), grease,sealant, thermostat, fuses; in addition to the appropriate tools, testing equipment, safety shoes and apparel for technicians, personal protective equipment (hands, hearing, eye protection), MSDS, cleaning material and oil spill containment kits. The contractor should inventory the supply after each visit and order replacement supplies and have them delivered on site. Maintenance materials shall be unused and are to be industry standard and intended for the task to be performed. Parts are to be OEM approved. Refrigerants are to meet the AHRI_Standard_700- 2015 or most recent AHRI Standards.

Refrigerants, parts and maintenance materials delivered to the post are to be new and unused.

Reclaimed refrigerants are not to be delivered to posts. Reclaimed refrigerants within post compounds are to be retained and stored and may be used if not contaminated. Refrigerants shall be stored in containers clearly indicating the refrigerant type.

SAFETY AND SPECIAL INSTRUCTIONS:

1. Follow site safety procedures and supervisor’s instructions.

2. Schedule outage with operating personnel.

3. Use extreme caution when climbing access ladders.

4. Perform applicable lockout/tag out steps of site safety procedures.

5. Lockout and disconnect the main power before tightening the main supply lugs in order to avoid the hazard of electrical shock, which could result in serious personal injury or death.

12 | P a g e

6. Record and report equipment damage or deficiencies.

7. Review and follow the manufacturer’s O&M instructions.

8. Record results in the equipment history log.

9. Allow only qualified personnel to do maintenance work on this equipment.

10. Record results in the equipment history log.

11. Check manufacturer’s specifications for the maximum number of plugged tubes.

12. Allow only qualified personnel to do maintenance work on this equipment.

CHILLERS

MAINTENANCE PROCEDURES:

Water Cooled Centrifugal Chiller:

Annually

1. Disconnect power source and lock out and tag out accordingly. Check electrical wiring and connections; tighten loose connections.

2. Perform the following tests:

Compressor Motor

• Motor continuity.

• Motor meg test.

• Check motor terminals.

• Inspect motor terminal board.

Starter or AFD

• Inspect starter contacts.

• Check all connections per manufacturer specifications.

• Follow all manufacturer recommendations for starter or AFD maintenance.

• Inspect/clean/service the AFD cooling system (water- or air-cooled AFD).

• Record all applicable starter or starter component settings.

Oil System

• Annual oil analysis (follow recommendations).

• Clean and lubricate oil system as required.

• Electrical inspection.

• Pump motor continuity check.

• Run oil pump and check differential oil pressure.

Condenser

• Inspect for fouling and scaling in tubes. Clean tubes as necessary with a proper brush machine

• Check operation of condenser water flow sensing device.

• Factory recommendation to eddy current test tubes every three years.

13 | P a g e

Evaporator

• Inspect for fouling and scaling in tubes. Clean tubes as necessary with a proper brush machine

• Check operation of evaporator water flow sensing device.

• Factory recommendation to eddy current test tubes every three years.

Control Circuits

• Verify control parameters.

• Test appropriate sensors for accuracy.

• Ensure sensors are properly seated in wells with thermopaste installed.

• Check evaporator leaving water temperature low temperature cutout setpoint.

• Condenser high pressure switch check-out.

• Check adjustment and operation of the inlet guide vane actuator.

Leak Test Chiller

• Check purge times and unit performance logs. If warranted, pressure leak test.

• Review oil analysis. If required, submit refrigerant sample for analysis.

• Inspect unit for any signs of refrigerant or oil leakage.

• Check unit for any loose bolts on flange, volutes, or casing.

Purge Unit

• Review the purge Installation, Operation, and Maintenance manual and follow maintenance and/or inspection items identified.

• Review purge pump out data.

• Review overall operation of purge and service as necessary.

Exterior

• Inlet guide vane linkage.

• Clean and touch-up painted surfaces as needed.

• Repair deteriorated, torn, or missing insulation

3. Perform the annual maintenance procedures referred to in Operation and Maintenance Guide: EarthWise™ Purge System with Tracer AdaptiView™ Control for Water-Cooled CenTraVac™ Chillers (PRGD-SVX01*-EN).

4. Submit a sample of the compressor oil to a Trane qualified laboratory for comprehensive analysis.

5. Measure the compressor motor winding resistance to ground; a qualified service technician should conduct this check to ensure that the findings are properly interpreted.

Contact a qualified service organization to leak-test the chiller; this procedure is especially important if the system requires frequent purging.

6. Inspect and clean the ifm efector® flow detection sensors. Use Scotch-Brite® or other non-abrasive material to clean scale; do NOT use steel wool, which could cause the probe to rust.

7. Clean area around equipment

14 | P a g e

8. Document all maintenance and cleaning procedures.

Panel, Electronic Controls:

Annually

1. Clean panel interior.

2. Verify functionality of supported devices.

3. Clean ventilation filter and fan (if applicable).

4. Record and report equipment damage or deficiencies.

5. Record results in the equipment history log

Spare Parts and Expendables Inventory.

There will be a minimum required expendable and common parts, provided by the Embassy, to be maintained on site by the contractor for normal maintenance to include:

Oil refrigerant Trane OIL00022, two 9 gallon buckets

R-123 Refrigerant, one 100 lb/drum

Oil filters, two each

Drier, liquid line filter, two each

Dryer filters for the purgue unit

Goodway Tube Cleaner USA Embassy Lima will provide this equipment for condensers & evaporator cleaning

Chillers Submitals Shown on separate attachment

Air Cooled Screw Chiller:

Weekly These activities and tasks shall be performed by Embassy staff and monitored by the BME Chillers Contractor While unit is running in stable conditions.

1. Check MP pressure for evaporator, condenser and intermediate oil.

2.Observe liquid line sight glass on EXV.

3.If liquid line sight glass has bubbles measure the subcooling entering the EXV. The subcooling should never be less than 4°F under any circumstances.

Important: A clear sightglass alone does not mean that the system is properly charged. Also check the rest of the system operating conditions.

4.Inspect the entire system for unusual conditions and inspect the condenser coils for dirt and debris. If the coils are dirty, refer to coil cleaning.

15 | P a g e

Monthly These activities and tasks shall be performed by Embassy staff and monitored by the BME Chillers Contractor

1. Perform all weekly maintenance procedures.

2. Record the system subcooling.

3. Make any repairs necessary.

Annual These activities and tasks shall be performed by the BME Chillers Contractor

1. Perform all weekly and monthly procedures.

2. Check oil sump oil level while unit is off.

Note: Routine changing of oil is not required. Use an oil analysis to determine condition of oil.

3. Have a qualified laboratory perform a compressor oil analysis to determine system moisture content and acid level. This analysis is a valuable diagnostic tool.

4. Perform a qualified and certified service to leak test the chiller, to check operating and safety controls, and to inspect electrical components for deficiencies.

5. Inspect all piping components for leakage and damage. Clean out any inline strainers.

6. Clean the condenser coils at least once a year or more frequently if the unit is in a “dirty” environment. A clean condenser coil will help to maintain chiller operating efficiency. Follow the detergent manufacturer's instructions to avoid damaging the condenser coils.

7. Replace oil filters and refrigerant dryers as needed.

8. To clean the condenser coils use a soft brush and a sprayer such as a garden pump type or a high-pressure type. A high quality detergent such as Trane Coil Cleaner (Part No.CHM-00255) is recommended.

Note: If detergent mixture is strongly alkaline (pH value greater than 8.5, an inhibitor must be add

Panel, Electronic Controls:

Annually

1. Clean panel interior.

2. Verify functionality of supported devices.

3. Clean ventilation filter and fan (if applicable).

4. Record and report equipment damage or deficiencies

Spare Parts and Expendables Inventory.

There will be a minimum required expendable and common parts to be maintained on site by the contractor for normal maintenance to include:

Oil refrigerant Trane, three 1 gallon buckets

R-134A Refrigerant, one 100 lb/drum

Oil filters, two each

Drier, liquid line filter, two each

END OF STATEMENT OF WORK

16 | P a g e

QUALITY ASSURANCE AND SURVEILLANCE PLAN (QASP)

This plan provides an effective method to promote satisfactory contractor performance. The QASP provides a method for the Contracting Officer's Representative (COR) to monitor Contractor performance, advise the Contractor of unsatisfactory performance, and notify the Contracting Officer of continued unsatisfactory performance. The Contractor, not the Government, is responsible for management and quality control to meet the terms of the contract. The role of the Government is to monitor quality to ensure that contract standards are achieved.

Performance Objective Scope of Work Pages

Performance Threshold

Services.

Performs all Chillers Maintenance Services set forth in the Statement of Work.

6 thru 15

All required services are performed and no more than one (1) customer complaint is received per month.

1. SURVEILLANCE. The COR will receive and document all complaints from Government personnel regarding the services provided. If appropriate, the COR will send the complaints to the Contractor for corrective action.

2. STANDARD. The performance standard is that the Government receives no more than one (1) customer complaint per month. The COR shall notify the Contracting Officer of the complaints so that the Contracting Officer may take appropriate action to enforce the inspection clause (FAR 52.212.4, Contract Terms and Conditions-Commercial Items (May 2001), if any of the services exceed the standard.

3. PROCEDURES.

(a) If any Government personnel observe unacceptable services, either incomplete work or required services not being performed they should immediately contact the COR.

(b) The COR will complete appropriate documentation to record the complaint.

(c) If the COR determines the complaint is invalid, the COR will advise the complainant. The

COR will retain the annotated copy of the written complaint for his/her files.

(d) If the COR determines the complaint is valid, the COR will inform the Contractor and give the Contractor additional time to correct the defect, if additional time is available. The COR shall determine how much time is reasonable.

(e) The COR shall, as a minimum, orally notify the Contractor of any valid complaints.

(f) If the Contractor disagrees with the complaint after investigation of the site and challenges the validity of the complaint, the Contractor will notify the COR. The COR will review the matter to determine the validity of the complaint.

(g) The COR will consider complaints as resolved unless notified otherwise by the complainant.

(h) Repeat customer complaints are not permitted for any services. If a repeat customer complaint is received for the same deficiency during the service period, the COR will contact the Contracting Officer for appropriate action under the Inspection clause.

17 | P a g e

Site Chiller Pictures

Water Cooled Centrifugal Chillers

RM-2 & RM-1 Front View

18 | P a g e

RM-2 Front View

RM-1 Front View

19 | P a g e

RM-1 Back View Evaporator Side

RM-2 Back View Condenser Side

20 | P a g e

RM-1 Back View Condenser Side

21 | P a g e

Chiller 1 Back View

22 | P a g e

Chiller 1 Nameplate

Chiller 2 Nameplate

23 | P a g e

Chiller 1 Back View

Chiller 2 Back View

24 | P a g e

Chiller 1 Compressor 2 of 2

Chiller 2 Compressor 1 of 2

25 | P a g e

Chiller 1 Chilled Water Piping

END OF SITE CHILLER PICTURES

26 | P a g e

SECTION 2 - CONTRACT CLAUSES

FAR 52.212-4 CONTRACT TERMS AND CONDITIONS – COMMERICAL ITEMS (OCT 2018) and

(DEVIATION 2017-02) (JUNE 2017, is incorporated by reference (see SF-1449, Block 27A)

FAR 52.212-5 CONTRACT TERMS AND CONDITIONS REQUIRED TO IMPLEMENT STATUTES OR EXECUTIVE

ORDERS-COMMERCIAL ITEMS (MAR 2020)

(a) The Contractor shall comply with the following Federal Acquisition Regulation (FAR) clauses, which are incorporated in this contract by reference, to implement provisions of law or Executive orders applicable to acquisitions of commercial items:

(1) 52.203-19, Prohibition on Requiring Certain Internal Confidentiality Agreements or Statements (Jan 2017) (section 743 of Division E, Title VII, of the Consolidated and Further Continuing Appropriations Act, 2015 (Pub. L. 113-235) and its successor provisions in subsequent appropriations acts (and as extended in continuing resolutions)).

(2) 52.204-23, Prohibition on Contracting for Hardware, Software, and Services Developed or Provided by Kaspersky Lab and Other Covered Entities (Jul 2018) (Section 1634 of Pub. L. 115-91).

(3) 52.204-25, Prohibition on Contracting for Certain Telecommunications and Video Surveillance Services or Equipment. (Aug 2019) (Section 889(a)(1)(A) of Pub. L. 115-232).

(4) 52.209-10, Prohibition on Contracting with Inverted Domestic Corporations (Nov 2015).

(5) 52.233-3, Protest After Award (Aug 1996) (31 U.S.C. 3553).

(6) 52.233-4, Applicable Law for Breach of Contract Claim (Oct 2004) (Public Laws 108- 77 and 108-78 (19 U.S.C. 3805note)).

(b) The Contractor shall comply with the FAR clauses in this paragraph (b) that the Contracting Officer has indicated as being incorporated in this contract by reference to implement provisions of law or Executive orders applicable to acquisitions of commercial items:

__ (1) 52.203-6, Restrictions on Subcontractor Sales to the Government (Sept 2006), with Alternate I (Oct 1995) (41 U.S.C. 4704 and 10 U.S.C. 2402).

__ (2) 52.203-13, Contractor Code of Business Ethics and Conduct (Oct 2015) (41 U.S.C. 3509)).

https://www.acquisition.gov/content/part-52-solicitation-provisions-and-contract-clauses#i52_203-19 https://www.acquisition.gov/content/part-52-solicitation-provisions-and-contract-clauses#id189A70O0P1N https://www.acquisition.gov/content/part-52-solicitation-provisions-and-contract-clauses#unique_37607080 https://www.acquisition.gov/content/part-52-solicitation-provisions-and-contract-clauses#i1062680 https://www.acquisition.gov/content/part-52-solicitation-provisions-and-contract-clauses#i1048661 http://uscode.house.gov/browse.xhtml;jsessionid=114A3287C7B3359E597506A31FC855B3 https://www.acquisition.gov/content/part-52-solicitation-provisions-and-contract-clauses#i1048698 http://uscode.house.gov/browse.xhtml;jsessionid=114A3287C7B3359E597506A31FC855B3 https://www.acquisition.gov/content/part-52-solicitation-provisions-and-contract-clauses#i1063319 http://uscode.house.gov/browse.xhtml;jsessionid=114A3287C7B3359E597506A31FC855B3 http://uscode.house.gov/browse.xhtml;jsessionid=114A3287C7B3359E597506A31FC855B3 https://www.acquisition.gov/content/part-52-solicitation-provisions-and-contract-clauses#i1063504 http://uscode.house.gov/browse.xhtml;jsessionid=114A3287C7B3359E597506A31FC855B3

27 | P a g e

__ (3) 52.203-15, Whistleblower Protections under the American Recovery and Reinvestment Act of 2009 (June 2010) (Section 1553 of Pub. L. 111-5). (Applies to contracts funded by the American Recovery and Reinvestment Act of 2009.)

(4) 52.204-10, Reporting Executive Compensation and First-Tier Subcontract Awards (Oct 2018) (Pub. L. 109-282) (31 U.S.C. 6101 note).

__ (5) [Reserved].

(6) 52.204-14, Service Contract Reporting Requirements (Oct 2016) (Pub. L. 111-117, section 743 of Div. C).

(7) 52.204-15, Service Contract Reporting Requirements for Indefinite-Delivery Contracts (Oct 2016) (Pub. L. 111-117, section 743 of Div. C).

(8) 52.209-6, Protecting the Government’s Interest When Subcontracting with Contractors Debarred, Suspended, or Proposed for Debarment. (Oct 2015) (31 U.S.C. 6101note).

__ (9) 52.209-9, Updates of Publicly Available Information Regarding Responsibility Matters (Oct 2018) (41 U.S.C. 2313).

__ (10) [Reserved].

__ (11) (i) 52.219-3, Notice of HUBZone Set-Aside or Sole-Source Award (Mar 2020) (15 U.S.C.657a).

__ (ii) Alternate I (Mar 2020) of 52.219-3.

__ (12) (i) 52.219-4, Notice of Price Evaluation Preference for HUBZone Small Business Concerns (Mar 2020) (if the offeror elects to waive the preference, it shall so indicate in its offer) (15 U.S.C. 657a).

__ (ii) Alternate I (Mar 2020) of 52.219-4.

__ (13) [Reserved]

__ (14) (i) 52.219-6, Notice of Total Small Business Set-Aside (Mar 2020) (15 U.S.C.644).

__ (ii) Alternate I (Mar 2020).

__ (iii) Alternate II (Nov 2011).

__ (15) (i) 52.219-7, Notice of Partial Small Business Set-Aside (Mar 2020) (15 U.S.C. 644).

__ (ii) Alternate I (Mar 2020) of 52.219-7.

__ (iii) Alternate II (Mar 2004) of 52.219-7.

https://www.acquisition.gov/content/part-52-solicitation-provisions-and-contract-clauses#i1063607 https://www.acquisition.gov/content/part-52-solicitation-provisions-and-contract-clauses#i1064087 http://uscode.house.gov/view.xhtml?req=granuleid:USC-prelim-title31-section6101&num=0&edition=prelim https://www.acquisition.gov/content/part-52-solicitation-provisions-and-contract-clauses#i1064214 https://www.acquisition.gov/content/part-52-solicitation-provisions-and-contract-clauses#i1064243 https://www.acquisition.gov/content/part-52-solicitation-provisions-and-contract-clauses#i1062590 http://uscode.house.gov/view.xhtml?req=granuleid:USC-prelim-title31-section6101&num=0&edition=prelim https://www.acquisition.gov/content/part-52-solicitation-provisions-and-contract-clauses#i1062651 http://uscode.house.gov/view.xhtml?req=granuleid:USC-prelim-title41-section2313&num=0&edition=prelim https://www.acquisition.gov/content/part-52-solicitation-provisions-and-contract-clauses#i1057314 http://uscode.house.gov/view.xhtml?req=granuleid:USC-prelim-title15-section637a&num=0&edition=prelim https://www.acquisition.gov/content/part-52-solicitation-provisions-and-contract-clauses#i1057314 https://www.acquisition.gov/content/part-52-solicitation-provisions-and-contract-clauses#i1057352 http://uscode.house.gov/browse.xhtml;jsessionid=114A3287C7B3359E597506A31FC855B3 https://www.acquisition.gov/content/part-52-solicitation-provisions-and-contract-clauses#i1057352 https://www.acquisition.gov/content/part-52-solicitation-provisions-and-contract-clauses#i1057393 http://uscode.house.gov/browse.xhtml;jsessionid=114A3287C7B3359E597506A31FC855B3 https://www.acquisition.gov/content/part-52-solicitation-provisions-and-contract-clauses#i1057419 http://uscode.house.gov/browse.xhtml;jsessionid=114A3287C7B3359E597506A31FC855B3 https://www.acquisition.gov/content/part-52-solicitation-provisions-and-contract-clauses#i1057419 https://www.acquisition.gov/content/part-52-solicitation-provisions-and-contract-clauses#i1057419

28 | P a g e

__ (16) 52.219-8, Utilization of Small Business Concerns (Oct 2018) (15 U.S.C. 637(d)(2) and (3)).

__ (17) (i) 52.219-9, Small Business Subcontracting Plan (Mar 2020) (15 U.S.C. 637(d)(4)).

__ (ii) Alternate I (Nov 2016) of 52.219-9.

__ (iii) Alternate II (Nov 2016) of 52.219-9.

__ (iv) Alternate III (Mar 2020) of 52.219-9.

__ (v) Alternate IV (Aug 2018) of 52.219-9

__ (18) 52.219-13, Notice of Set-Aside of Orders (Mar 2020) (15 U.S.C. 644(r)).

__ (19) 52.219-14, Limitations on Subcontracting (Mar 2020) (15 U.S.C.637(a)(14)).

__ (20) 52.219-16, Liquidated Damages-Subcontracting Plan (Jan 1999) (15 U.S.C. 637(d)(4)(F)(i)).

__ (21) 52.219-27, Notice of Service-Disabled Veteran-Owned Small Business Set-Aside (Mar 2020) (15 U.S.C. 657f).

__ (22) (i) 52.219-28, Post Award Small Business Program Rerepresentation (Mar 2020) (15 U.S.C. 632(a)(2)).

(ii) Alternate I (MAR 2020) of 52.219-28.

__ (23) 52.219-29, Notice of Set-Aside for, or Sole Source Award to, Economically Disadvantaged Women-Owned Small Business Concerns (Mar 2020) (15 U.S.C. 637(m)).

__ (24) 52.219-30, Notice of Set-Aside for, or Sole Source Award to, Women-Owned Small Business Concerns Eligible Under the Women-Owned Small Business Program (Mar 2020) (15 U.S.C. 637(m)).

(25) 52.219-32, Orders Issued Directly Under Small Business Reserves (Mar 2020) (15 U.S.C. 644(r)).

(26) 52.219-33, Nonmanufacturer Rule (Mar 2020) (15 U.S.C. 637(a)(17)).

__ (27) 52.222-3, Convict Labor (June 2003) (E.O.11755).

(28) 52.222-19, Child Labor-Cooperation with Authorities and Remedies (Jan 2020) (E.O.13126).

(29) 52.222-21, Prohibition of Segregated Facilities (Apr 2015).

https://www.acquisition.gov/content/part-52-solicitation-provisions-and-contract-clauses#i52_219-8 http://uscode.house.gov/browse.xhtml;jsessionid=114A3287C7B3359E597506A31FC855B3 https://www.acquisition.gov/content/part-52-solicitation-provisions-and-contract-clauses#i52_219-9 http://uscode.house.gov/browse.xhtml;jsessionid=114A3287C7B3359E597506A31FC855B3 https://www.acquisition.gov/content/part-52-solicitation-provisions-and-contract-clauses#i52_219-9 https://www.acquisition.gov/content/part-52-solicitation-provisions-and-contract-clauses#i52_219-9 https://www.acquisition.gov/content/part-52-solicitation-provisions-and-contract-clauses#i52_219-9 https://www.acquisition.gov/content/part-52-solicitation-provisions-and-contract-clauses#i52_219-9 https://www.acquisition.gov/content/part-52-solicitation-provisions-and-contract-clauses#i1057715 http://uscode.house.gov/browse.xhtml;jsessionid=114A3287C7B3359E597506A31FC855B3 https://www.acquisition.gov/content/part-52-solicitation-provisions-and-contract-clauses#i1057730 http://uscode.house.gov/browse.xhtml;jsessionid=114A3287C7B3359E597506A31FC855B3 https://www.acquisition.gov/content/part-52-solicitation-provisions-and-contract-clauses#i1057758 http://uscode.house.gov/browse.xhtml;jsessionid=114A3287C7B3359E597506A31FC855B3 https://www.acquisition.gov/content/part-52-solicitation-provisions-and-contract-clauses#i1057823 http://uscode.house.gov/browse.xhtml;jsessionid=114A3287C7B3359E597506A31FC855B3 https://www.acquisition.gov/content/part-52-solicitation-provisions-and-contract-clauses#i1057874 http://uscode.house.gov/browse.xhtml;jsessionid=114A3287C7B3359E597506A31FC855B3 https://www.acquisition.gov/content/part-52-solicitation-provisions-and-contract-clauses#i1057874 https://www.acquisition.gov/content/part-52-solicitation-provisions-and-contract-clauses#i1057902 http://uscode.house.gov/browse.xhtml;jsessionid=114A3287C7B3359E597506A31FC855B3 https://www.acquisition.gov/content/part-52-solicitation-provisions-and-contract-clauses#i1057947 http://uscode.house.gov/browse.xhtml;jsessionid=114A3287C7B3359E597506A31FC855B3 https://www.govinfo.gov/content/pkg/USCODE-2018-title15/html/USCODE-2018-title15-chap14A-sec644.htm https://www.govinfo.gov/content/pkg/USCODE-2018-title15/html/USCODE-2018-title15-chap14A-sec644.htm https://www.govinfo.gov/content/pkg/USCODE-2018-title15/html/USCODE-2018-title15-chap14A-sec637.htm https://www.acquisition.gov/content/part-52-solicitation-provisions-and-contract-clauses#i1055332 https://www.acquisition.gov/content/part-52-solicitation-provisions-and-contract-clauses#i1055664 https://www.acquisition.gov/content/part-52-solicitation-provisions-and-contract-clauses#i1055713

29 | P a g e

(30) (i) 52.222-26, Equal Opportunity (Sept 2016) (E.O.11246).

__ (ii) Alternate I (Feb 1999) of 52.222-26.

__ (31) (i) 52.222-35, Equal Opportunity for Veterans (Oct 2015) (38 U.S.C. 4212).

__ (ii) Alternate I (July 2014) of 52.222-35.

__ (32) (i) 52.222-36, Equal Opportunity for Workers with Disabilities (Jul 2014) (29 U.S.C.793).

__ (ii) Alternate I (July 2014) of 52.222-36.

__ (33) 52.222-37, Employment Reports on Veterans (Feb 2016) (38 U.S.C. 4212).

__ (34) 52.222-40, Notification of Employee Rights Under the National Labor Relations Act (Dec 2010) (E.O. 13496).

(35) (i) 52.222-50, Combating Trafficking in Persons (Jan 2019) (22 U.S.C. chapter 78 and E.O. 13627).

__ (ii) Alternate I (Mar 2015) of 52.222-50 (22 U.S.C. chapter78 and E.O. 13627).

__ (36) 52.222-54, Employment Eligibility Verification (Oct 2015). (Executive Order 12989). (Not applicable to the acquisition of commercially available off-the-shelf items or certain other types of commercial items as prescribed in 22.1803.)

__ (37) (i) 52.223-9, Estimate of Percentage of Recovered Material Content for EPA– Designated Items (May 2008) (42 U.S.C. 6962(c)(3)(A)(ii)). (Not applicable to the acquisition of commercially available off-the-shelf items.)

__ (ii) Alternate I (May 2008) of 52.223-9 (42 U.S.C. 6962(i)(2)(C)). (Not applicable to the acquisition of commercially available off-the-shelf items.)

__ (38) 52.223-11, Ozone-Depleting Substances and High Global Warming Potential Hydrofluorocarbons (Jun 2016) (E.O. 13693).

__ (39) 52.223-12, Maintenance, Service, Repair, or Disposal of Refrigeration Equipment and Air Conditioners (Jun 2016) (E.O. 13693).

__ (40) (i) 52.223-13, Acquisition of EPEAT®-Registered Imaging Equipment (Jun 2014) (E.O.s 13423 and 13514).

__ (ii) Alternate I (Oct 2015) of 52.223-13.

__ (41) (i) 52.223-14, Acquisition of EPEAT®-Registered Televisions (Jun 2014) (E.O.s 13423 and 13514).

__ (ii) Alternate I (Jun 2014) of 52.223-14.

https://www.acquisition.gov/content/part-52-solicitation-provisions-and-contract-clauses#i1055793 https://www.acquisition.gov/content/part-52-solicitation-provisions-and-contract-clauses#i1055793 https://www.acquisition.gov/content/part-52-solicitation-provisions-and-contract-clauses#i1056230 http://uscode.house.gov/view.xhtml?req=granuleid:USC-prelim-title38-section4212&num=0&edition=prelim https://www.acquisition.gov/content/part-52-solicitation-provisions-and-contract-clauses#i1056230 https://www.acquisition.gov/content/part-52-solicitation-provisions-and-contract-clauses#i1056250 http://uscode.house.gov/view.xhtml?req=granuleid:USC-prelim-title29-section793&num=0&edition=prelim https://www.acquisition.gov/content/part-52-solicitation-provisions-and-contract-clauses#i1056250 https://www.acquisition.gov/content/part-52-solicitation-provisions-and-contract-clauses#i1056265 http://uscode.house.gov/view.xhtml?req=granuleid:USC-prelim-title38-section4212&num=0&edition=prelim https://www.acquisition.gov/content/part-52-solicitation-provisions-and-contract-clauses#i1056304 https://www.acquisition.gov/content/part-52-solicitation-provisions-and-contract-clauses#i1056535 http://uscode.house.gov/browse.xhtml;jsessionid=114A3287C7B3359E597506A31FC855B3 https://www.acquisition.gov/content/part-52-solicitation-provisions-and-contract-clauses#i1056535 http://uscode.house.gov/browse.xhtml;jsessionid=114A3287C7B3359E597506A31FC855B3 https://www.acquisition.gov/content/part-52-solicitation-provisions-and-contract-clauses#i1056753 https://www.acquisition.gov/content/part-22-application-labor-laws-government-acquisitions#i1095479 https://www.acquisition.gov/content/part-52-solicitation-provisions-and-contract-clauses#i1053138 http://uscode.house.gov/browse.xhtml;jsessionid=114A3287C7B3359E597506A31FC855B3 https://www.acquisition.gov/content/part-52-solicitation-provisions-and-contract-clauses#i1053138 http://uscode.house.gov/browse.xhtml;jsessionid=114A3287C7B3359E597506A31FC855B3 https://www.acquisition.gov/content/part-52-solicitation-provisions-and-contract-clauses#i1053180 https://www.acquisition.gov/content/part-52-solicitation-provisions-and-contract-clauses#i1053196 https://www.acquisition.gov/content/part-52-solicitation-provisions-and-contract-clauses#i1053207 https://www.acquisition.gov/content/part-52-solicitation-provisions-and-contract-clauses#i1053207 https://www.acquisition.gov/content/part-52-solicitation-provisions-and-contract-clauses#i1053232 https://www.acquisition.gov/content/part-52-solicitation-provisions-and-contract-clauses#i1053232

30 | P a g e

__ (42) 52.223-15, Energy Efficiency in Energy-Consuming Products (Dec 2007) (42 U.S.C. 8259b).

__ (43) (i) 52.223-16, Acquisition of EPEAT®-Registered Personal Computer Products (Oct 2015) (E.O.s 13423 and 13514).

__ (ii) Alternate I (Jun 2014) of 52.223-16.

(44) 52.223-18, Encouraging Contractor Policies to Ban Text Messaging While Driving (Aug 2011) (E.O. 13513).

__ (45) 52.223-20, Aerosols (Jun 2016) (E.O. 13693).

__ (46) 52.223-21, Foams (Jun 2016) (E.O. 13693).

__ (47) (i) 52.224-3 Privacy Training (Jan 2017) (5 U.S.C.