2073FJ_Engineering_Instructions.pdf

REV: ENGINEERING DATA REQUIREMENTS

(ATTACHMENT “A”)

NOTE: MILITARY SPECIFICATIONS / STANDARDS WILL NOT BE FURNISHED IN THE BID SET.

1. THE FOLLOWING INSTRUCTIONS ARE FURNISHED FOR THE MANUFACTURE OF:

RIB, AIRFOIL A-10

2. PART NUMBER:

160D612105-13

3. NATIONAL STOCK NUMBER:

1560-01-227-2073 FJ

PREPARED BY:

Ezekiel Smith

OFFICE SYMBOL:

416 SCMS/GUEAB

DATE:

20210528

HILL AFB FORM 462 Page 1 of 1

4. THE FOLLOWING SPECIFICATIONS/STANDARDS, ETC. WILL BE USED IN LIEU OF THE DATA INDICATED. THE SUPERSEDED DATA

WILL NOT BE FURNISHED UNLESS SO INDICATED.

5. CONTRACTOR IS RESPONSIBLE TO COMPLETELY RESEARCH THESE MANUALS, SPECIFICATIONS, AND STANDARDS AND FULLY

UNDERSTAND THE REQUIREMENTS NECESSARY FOR MANUFACTURE OF COMPONENT PARTS AND ASSEMBLIES. ALL DEVIATIONS, MINOR AND MAJOR, FROM THE ENGINEERING DRAWING PACKAGE SHALL BE SUBMITTED TO THE 416 SCMS/GUEAB A-10 STRUCTURAL SYSTEMS ENGINEERING OR OO-ALC/GHAEB A-10 MECHANICAL SYSTEMS ENGINEERING DEPENDING ON THE

APPLICABLE SYSTEM.

6. WHEN MILITARY DOCUMENTS LISTED IN THE ENGINEERING DRAWING ARE CANCELLED THEY SHALL BE REPLACED BY THE

INDUSTRY EQUIVALENT DOCUMENT SPECIFIED ON THE MILITARY DOCUMENT'S CANCELLATION NOTICE. THIS APPLIES TO THE ORIGINAL AIRCRAFT MANUFACTURER'S SPECIFICATIONS THAT ARE CITED IN THE DRAWING, AS WELL. THE CHARACTERISTICS OF TYPE, GRADE, CLASS, ETC. SPECIFIED IN THE CANCELLED MILITARY DOCUMENT SHALL BE MAINTAINED OR EXCEED THOSE CHARACTERISTICS WHEN APPLYING THE INDUSTRY EQUIVALENT DOCUMENT(S). WHEN THERE IS NO LISTED REPLACEMENT THE CONTRACTOR SHALL REQUEST AND RECOMMEND A SUBSTITUTE DOCUMENT FROM THE 416 SCMS/GUEAB STRUCTURAL SYSTEMS ENGINEERING OR THE OO-ALC/GHAEB A-10 MECHANICAL SYSTEMS ENGINEERING THROUGH THE GOVERNMENT

CONTRACTING OFFICIAL DEPENDING ON THE APPLICABLE SYSTEM.

7. USE OF NORTHROP GRUMMAN SPECIFICATION Z-R701 IN CONJUNCTION WITH MIL-STD-130 IS MANDATORY TO ENSURE THE

PROPER MARKING OF THE PARTS. (Z-R701 HAS UNLIMITED DATA RIGHTS IN JEDMICS)

8. "IUID" (ITEM UNIQUE IDENTIFIER) IS REQUIRED IAW MIL-STD-130. SPECIFIC INSTRUCTIONS FOR MARKING METHODS, LOCATION, CONTENT AND FORMAT SHALL BE SPECIFIED BY THE CONTRACTOR AND SUBMITTED TO THE GOVERNMENT FOR APPROVAL PRIOR TO CONTRACT DELIVERY. THE CONTRACTOR MUST DEMONSTRATE THE MARKING DOES NOT ADVERSELY AFFECT ITEM INTEGRITY OR PERFORMANCE AND WILL REMAIN READABLE AND ATTACHED THROUGHOUT THE USEABLE LIFE OF THE ITEM.

9. AS DEFINED BY THE CAD MODEL, THE POSITION TOLERANCE ON THE 5-.2525” DIAMETER HOLES IS .0010” AND THE HOLE

DIAMETER TOLERANCE IS .2525” TO .2530”.

10. 3-D MODELS ARE AVAILABLE AND REQUIRED FOR THE MANUFACTURE OF MULTIPLE COMPONENTS USED IN THIS ASSEMBLY.

NOTE THAT 3-D MODELS ARE NOT AVAILABLE FOR ALL PARTS. WHERE 3-D MODELS ARE REQUIRED AND AVAILABLE, THE ASSOCIATED DRAWING IS NECESSARY FOR NOTES, TOLERANCES AND OTHER APPLICABLE CONFIGURATION DETAILS.

COMPONENTS, HARDWARE, AND OTHER PERTINENT DETAILS MAY NOT BE PRESENT IN ASSEMBLY MODELS; REFER TO THE PARTS LIST AND DRAWING FOR CONFIGURATION DETAILS. 3-D MODELS ARE STORED IN THE TEAMCENTER REPOSITORY.

CONTACT THE APPROPRIATE A-10 DATA CONTROL ORGANIZATION THROUGH THE GOVERNMENT PROCURING AGENCY FOR THE

APPLICABLE FILES.

11. PART NUMBER 160D612105-13 SHALL BE SUPPLIED FULLY ASSEMBLED, NOT DELIVERED AS A KIT.

12. WARNING - THE DOCUMENTS LISTED ON THIS ENGINEERING DATA LIST (EDL) CONTAIN TECHNICAL DATA WHOSE EXPORT IS

RESTRICTIVE BY THE ARMS EXPORT CONTROL ACT (TITLE 22, USC, SECTION 2751, ET SEQ.), OR THE EXPORT ADMINISTRATION ACT OF 1979, AS AMENDED, TITLE 50 U.S.C, APPEND 2401 ET SEQ. VIOLATORS OF THESE EXPORT LAWS ARE SUBJECT TO SEVERE

CRIMINAL PENALTIES.