2020-043446 IFQ Package.pdf

INVITATION FOR QUOTE/BID

ANNUAL CONTRACT

DATE: October 4, 2021

SENT TO: Qualified Contractors

On the Annual Contract – Low Voltage

SENT FROM: Capital Improvements Division

SENDER: Rocky Roque

PHONE: 561-233-2050

PROJECT NAME: MCCH - Sally Port Gate Installation

PROJECT NUMBER: 2020-043446

Mandatory Pre-Bid Conference. There will be a Mandatory Pre-Bid Meeting at October 19, 2021, located at Main County Courthouse (meet outside of front doors of courthouse), 205 N. Dixie Highway, West Palm Beach, FL at 10:00

AM on October 19, 2021. The purpose of this pre-bid meeting will be to review the requirements for the project described in this Invitation for Quote/Bid. The work is to be done under the terms and conditions of Palm Beach County’s

Annual Contract – Low Voltage as supplemented by this Invitation for

Quote/Bid. You must attend this meeting if you intend to bid this work.

Questions must be e-mailed to FDO-CID-Bids@pbcgov.org at least seven (7) calendar days prior to the bid due date. Only questions received in writing will be responded to regarding this Invitation for Quote/Bid.

Form Rev. 4/13/21 Invitation for Quote/Bid – Nonfederal

Dave Kerner, Mayor

Robert S. Weinroth, Vice Mayor

Maria G. Marino

Gregg K. Weiss

Maria Sachs

Melissa McKinlay

Mack Bernard mailto:FDO-CID-Bids@pbcgov.org

Submitting the Quote/Bid Package

The Quote/Bid Package shall be enclosed in a sealed opaque envelope. The envelope shall be addressed as follows:

Project Name: MCCH - Sally Port Gate Installation

Project Number: 2020-043446

Capital Improvements Division

2633 Vista Parkway

West Palm Beach, Florida 33411

Attention: Bid Submissions

No responsibility will be attached to the Owner for premature opening of or failure to open a quote/bid not properly identified. If the quote/bid is sent by mail, the sealed envelope shall be enclosed in a separate mailing with the notation "SEALED QUOTE/BID ENCLOSED" on the face thereof.

PROJECT NO.: 2020-043446

* DUE: November 18, 2021 by 2:00 PM

* The Quotes/Bids received by this time will be opened at this time at a public meeting at the below address.

RETURN TO: Capital Improvements Division

2633 Vista Parkway

West Palm Beach, FL 33411

Qualification of Contractors. In order to submit a quote/bid in response to this IFQ/B, a contractor must be qualified under the Annual Contract – Low Voltage. A contractor may obtain a Qualification Application for this Annual Contract by sending an email with the

Project # in the subject line to: FDO-CID-Bids@pbcgov.org or call (561) 233-0261.

Qualification applications may also be downloaded from the County’s on-line Vendor Self-

Service (VSS) system at https://pbcvssp.co.palm-beach.fl.us/webapp/vssp/AltSelfService.

The contractor must submit the Qualification Application at least 10 days before the

Quote/Bid Due Date in order for its quote/bid to be considered.

mailto:FDO-CID-Bids@pbcgov.org https://pbcvssp.co.palm-beach.fl.us/webapp/vssp/AltSelfService

1. SCOPE OF WORK: This Quote/Bid is to furnish all material, labor, supervision, permits and supplies necessary and reasonably incidental to install Sally Port gate per the specifications provided by Capital

Improvements Division in the Invitation for Quote/Bid at Attachment “C” and/or available at the pre-bid meeting held on October 19, 2021. Work is to be done under the terms and conditions of Palm Beach

County’s Annual Contract – Low Voltage, and pursuant to the conditions of the Work Order, both of which are incorporated into the Contract Documents by reference.

2. SCHEDULE OF TIME FOR COMPLETION. The time of completion for this Project will be as follows: The Contractor shall substantially complete the work within sixty (60) calendar days from permit issuance.

3. LIQUIDATED DAMAGES. Liquidated Damages are $80/day for failure to achieve certification of

Substantial Completion within the Work Order time or approved extension thereof.

4. BID SECURITY AND PUBLIC CONSTRUCTION BOND. Bid Security and Public Construction

Bond are required for this Project in accordance with Section 5.2 of the Instructions to Bidders of the Annual

Contract as follows:

Bid Security. If Bid is $200,000 or over, this Bid shall be accompanied by a Bid Security (in the form of, at Bidder's option, cashier's check, certified check, money order or Bid Bond in favor of the County) in the amount of at least five percent (5%) of the bid price, see Section 5.2.2 of the

Instructions to Bidders of the Annual Contract for detailed requirements regarding Bid Security.

Public Construction Bond. If Bid is $200,000 or over (or if cumulative open work orders are

$200,000 or over), then prior to execution of a Work Order, and not later than fourteen (14) calendar days after notification from Owner, the successful Bidder shall furnish a Public

Construction Bond in the amount of 100% of the Work Order and Guarantee, see Section 5.2.3 of the Instructions to Bidders of the Annual Contract for detailed requirements regarding the Public

Construction Bond and Guarantee.

5. Equal Business Opportunity Program. Section 5.3 of the Instruction to Bidders of the Annual Contract sets out the requirements of the County’s Equal Business Opportunity Program. All Bidders are required to submit with their bid the appropriate EBO Program schedules. EBO Schedules to be submitted with the quote/bid are as follows:

a) Schedule 1 - List of All Proposed Subcontractors, including S/M/WBE Participation. A completed Schedule 1 shall list the names of all subcontractors, including S/M/WBE subcontractors, intended to be used in performance of the Work Order, if awarded. This schedule shall also be used if an S/M/WBE prime bidder is performing any work and/or using any subcontractors.

b) Schedule(s) 2 - Letter(s) of Intent to Perform as a Subcontractor, including S/M/WBE Subcontractors. A Schedule 2 for each subcontractor, including each S/M/WBE subcontractor, listed on Schedule 1, shall be completed and executed by the proposed subcontractor. The type of Work to be performed by each subcontractor and the dollar value or percentage shall also be specified. Additional copies may be made as needed. A completed Schedule 2 is a binding agreement between the prime contractor and the subcontractor and should be treated as such.

Attachment “A” identifies the affirmative procurement initiatives (APIs) applicable to this Invitation for Quote/Bid.

If Bidder is unable to comply with the API requirements (Attachment “A” hereto), such Bidder shall submit a request for a waiver or partial waiver at least (7) days prior to the quote/bid due date If

Bidder requests a waiver from an API from the Office of EBO at least 7 days prior to the quote/bid due date, then the quote/bid due date will be extended pending the outcome of a waiver request.

Additionally, if the waiver is granted, the solicitation will be amended accordingly and the due date extended again.

6. Failure to Provide the Required Documents after Notification of Award. If after Notification of award from the County, the successful Bidder does not provide within 14 Days of Notification the signed

Work Order, the Public Construction Bond and Guarantee (when required), and the required certificates of insurance, the County may: 1. Call in the bid security when provided; 2. Cancel the notification of recommended award and award the project to the next responsive, responsible low bidder; 3. Terminate this Annual Contract for cause; 4. Suspend or debar the Bidder from bidding on future projects for a period of two (2) years, in accordance with the Palm Beach County Purchasing Ordinance; and/or 5. Pursue any and all remedies available against the Bidder for damages resulting from its failure to enter into a Work

Order and provide all required documents within 14 Days after notification.

7. CONTRACT AMENDMENTS. The Annual Contract is amended as follows: NONE.

Form Rev. 4/13/21 Bid Form - NonFederal

BID FORM

PROJECT NAME: MCCH - Sally Port Gate Installation

IN ORDER TO BE DEEMED RESPONSIVE TO THIS INVITATION FOR QUOTE/BID,

THE QUOTE/BID PACKAGE MUST CONTAIN:

a) This Quote/Bid Form completed and executed.

b) EBO Schedules 1 and 2 completed and executed.

c) Bid Security. (If the bid is $200,000 or more).

d) Signed Addenda, if any issued

THE FOLLOWING MUST BE COMPLETED AND SIGNED BY CONTRACTOR

1. TOTAL QUOTE/BID AMOUNT $ ____________

Written amount ____________

2. Bidder commits to achieving the APIs applicable to this solicitation as designated on Attachment

A and as submitted on its EBO Schedules 1 and 2.

3. Is the Bidder a Palm Beach County certified S/M/WBE? Yes_____ No_____

4. Commercial Non-Discrimination Certification. The undersigned Bidder hereby certifies and agrees that the following information is correct: In preparing its response to this Solicitation, the

Bidder has considered all proposals submitted from qualified, potential Subcontractors and suppliers, and has not engaged in "discrimination" as defined in the County’s Commercial

Nondiscrimination Policy as set forth in Resolution 2017-1770 as amended, to wit: discrimination in the solicitation, selection or commercial treatment of any Subcontractor, vendor, supplier or commercial customer on the basis of race, color, national origin, religion, ancestry, sex, age, marital status, familial status, sexual orientation, gender identity or expression, disability, or genetic information, or on the basis of any otherwise unlawful use of characteristics regarding the vendor's, supplier's or commercial customer's employees or owners; provided that nothing in this policy shall be construed to prohibit or limit otherwise lawful efforts to remedy the effects of discrimination that have occurred or are occurring in the County’s relevant marketplace of Palm

Beach County. Without limiting the foregoing, "discrimination" also includes retaliating against any person or other entity for reporting any incident of "discrimination." Without limiting any other provision of the solicitation, it is understood and agreed that, if this certification is false, such false certification will constitute grounds for the County to reject the bid submitted by the Bidder for this Solicitation, and to terminate any contract awarded based on the response. As part of its bid, the Bidder shall provide to the County a list of all instances within the immediate past four (4) years where there has been a final adjudicated determination in a legal or administrative proceeding in the State of Florida that the Bidder discriminated against its Subcontractors, vendors, suppliers or commercial customers, and a description of the status or resolution of that complaint, including any remedial action taken. As a condition of submitting a bid to the County, the Bidder agrees to

Form Rev. 4/13/21 Bid Form - NonFederal comply with the County’s Commercial Nondiscrimination Policy as described in Resolution 2017-

1770 as amended.

5. The Bidder shall be bound by the terms of its Bid for a period of one hundred twenty (120) calendar Days from the date of the bid opening and may not withdraw its Bid within that time period. If the County issues a Notification from Owner within the above 120-Day period, then the

Bidder will be bound by the Bid as submitted. If the County fails to issue a Notification from

Owner to the successful Bidder within the above identified 120-Day period, the successful bidder will not be required to honor its bid unless otherwise agreed to by both parties. County anticipates, but does not guarantee, the award of a Work Order and written notice to proceed within ninety (90) calendar Days of Notification from Owner, absent the filing of a timely bid protest.

6. It is agreed that the undersigned has received all addenda complete as issued by the County and that related costs are included in the bid submitted. The undersigned acknowledges receipt of said addenda as follows:

Addendum # dated Addendum# dated

Addendum # dated Addendum# dated

The undersigned has included the signed addenda, if issued, in its bid package.

7. The undersigned does hereby declare that the Bid covers all expenses of every kind incidental to the completion of said Work in accordance with the Contract Documents, including all claims that may arise through damages or other causes whatsoever. The undersigned does hereby declare that it shall make no claim on account of any variation from any estimate in the quantities of Work to be done, nor on account of any misunderstanding or misconception of the nature of the Work to be done or the grounds, subsurface conditions, or place where the Work is to be done.

QUOTE/BID PROVIDED BY:

Contractor Name

Date Signature

Print Name and Title

Quote/Bid Must Contain Original Signatures. No Copies or Emailed/Faxed Quotes/Bids Will

Be Accepted

REVISED 02/28/2019

OEBO SCHEDULE 1

LIST OF PROPOSED CONTRACTOR/CONSULTANT AND SUBCONTRACTOR/SUBCONSULTANT PARTICIPATION

SOLICITATION/PROJECT/BID NAME: _________________________________________ SOLICITATION/PROJECT/BID No.: ______________________________________

NAME OF PRIME RESPONDENT/BIDDER: ADDRESS: _________________________________________________________

CONTACT PERSON: _______________________________________________________ PHONE NO.: ___________________________ E-MAIL:______________________

SOLICITATION OPENING/SUBMITTAL DATE: ___________________________________ DEPARTMENT: ______________________________________________________

PLEASE LIST THE DOLLAR AMOUNT OR PERCENTAGE OF WORK TO BE COMPLETED BY THE PRIME CONTRACTOR/CONSULTANT ON THIS PROJECT.

PLEASE ALSO LIST THE DOLLAR AMOUNT OR PERCENTAGE OF WORK TO BE COMPLETED BY ALL SUBCONTRACTORS/SUBCONSULTANTS ON THE

PROJECT.

(Check all Applicable Categories) Non-SBE M/WBE SBE DOLLAR AMOUNT OR PERCENTAGE OF WORK

Name, Address and Phone Number Minority/Women Small

Business Business Black Hispanic Women Caucasian Other (Please Specify)

1.

2.

3.

4.

5.

(Please use additional sheets if necessary) Total ___ _____ __ ______ _________ _________ _________

Total Bid Price $________________________________________ Total SBE - M/WBE Participation _____________

I hereby certify that the above information is accurate to the best of my knowledge: ____________________________________________________________ ______________________________________ Signature Title

Note: 1. The amount listed on this form for a Subcontractor/subconsultant must be supported by price or percentage listed on the properly executed Schedule 2 or attached signed proposal.

2. Firms may be certified by Palm Beach County as an SBE and/or an M/WBE. If firms are certified as both an SBE and/or M/WBE, please indicate the dollar amount under the appropriate category.

3. Modification of this form is not permitted and will be rejected upon submittal.

Prime:

Subcontractor(s) if any:

THearn Highlight

OEBO LETTER OF INTENT – SCHEDULE 2

Revised 09/17/2019

A completed Schedule 2 is a binding document between the Prime Contractor/consultant and a Subcontractor/subconsultant (for any tier) and should be treated as such. The Schedule 2 shall contain bolded language indicating that by signing the Schedule 2, both parties recognize this Schedule as a binding document. All Subcontractors/subconsultants, including any tiered Subcontractors/subconsultants, must properly execute this document. Each properly executed Schedule 2 must be submitted with the bid/proposal.

SOLICITATION/PROJECT NUMBER: ________________________________________________________________________________

SOLICITATION/PROJECT NAME: __________________________________________________________________________________

Prime Contractor: ___________________________________________Subcontractor:______________________________________ (Check box(s) that apply) � SBE � WBE � MBE � M/WBE � Non-S/M/WBE Date of Palm Beach County Certification (if applicable):_______________.

The undersigned affirms they are the following (select one from each column if applicable):

Column 1 Column 2 Column 3

� Male � Female � African-American/Black � Asian American � Caucasian American � Supplier � Hispanic American � Native American

S/M/WBE PARTICIPATION – S/M/WBE Primes must document all work to be performed by their own work force on this form. Failure to submit a properly executed Schedule 2 for any S/M/WBE participation may result in that participation not being counted. Specify in detail, the scope of work to be performed or items supplied with the dollar amount and/or percentage for each work item. S/M/WBE credit will only be given for the areas in which the S/M/WBE is certified. A detailed proposal may be attached to a properly executed Schedule 2.

Line Item

Item Description Unit Price Quantity/ Units

Contingencies/ Allowances

Total Price/Percentage

The undersigned Subcontractor/subconsultant is prepared to self-perform the above-described work in conjunction with the aforementioned project at the following total price or percentage:

Print Name of Prime Print Name of Subcontractor/subconsultant

By: _____________________________________________ By: ________________________________________________

Authorized Signature Authorized Signature

Print Name Print Name

Title Title

Date: ___________________________________________ Date: ______________________________________________

If the undersigned intends to subcontract any portion of this work to another Subcontractor/subconsultant, please list the business name and the amount below accompanied by a separate properly executed Schedule 2.

Price or Percentage:

Name of 2nd/3rd tier Subcontractor/subconsultant

Highlight

SAMPLE

Form Rev 4/1/21 Attachment A for Asbestos Abatement, Low Voltage(9/12/16-9/12/21)

ATTACHMENT “A”

[for Asbestos Abatement, Low Voltage(9/12/16-9/12/21)]

AFFIRMATIVE PROCUREMENT INITIATIVES (APIs) FOR CONSTRUCTION

PROCUREMENT

The API(s) approved for this project are selected below by ☒. Fillable pdfs of all EBO forms can be found on the OEBO website at http://discover.pbcgov.org/oebo/Pages/Compliance-

Programs.aspx. Also, see the EBO Ordinance and Countywide PPM CW-O-043 for further information on APIs.

__X__ SBE Price Preference For Single Trade Construction

The work orders under this contract shall be awarded to the lowest, responsive, responsible bidder unless a certified SBE’s bid is within ten percent (10%) of the lowest non-SBE bid, in which case the award shall be made to the certified SBE bidder. Construction contracts where there are no opportunities for subcontracting (i.e.

single trade), may include a provision requiring awards of the contract to be made to the lowest responsive, responsible respondent or bidder unless a certified SBE’s bid is within ten (10) percent of the lowest non-small business bid, in which case the award shall be made to the certified small business bidder submitting the lowest responsive, responsible bid at the price that it bid.

http://discover.pbcgov.org/oebo/Pages/Compliance-Programs.aspx http://discover.pbcgov.org/oebo/Pages/Compliance-Programs.aspx

Form Rev. 4/13/21 Bid Bond - NonFederal

IFQ/B ATTACHMENT B

Include Attachment B if bid is $200,000 or more

DATE:

BID BOND

STATE OF FLORIDA

COUNTY OF PALM BEACH

KNOW ALL MEN BY THESE PRESENTS: That we, (hereinafter called "Principal"), and

(hereinafter called "Surety") are held and firmly bound unto Palm Beach County, a Political Subdivision in the State of Florida, by and through its Board of

County Commissioners, (hereinafter called "County") in the sum of

Dollars,($ ), (which sum is at least 5% of the bid price), lawful money of the United States of America, for the payment of which sum will and truly to be made, we bind ourselves, our heirs, executors, administrators and successors, jointly and severally, firmly be these presents;

WHEREAS, the "Principal" contemplates submitting or has submitted a bid to the Board of County

Commissioners, Palm Beach County, Florida, for furnishing and paying for all necessary labor materials, equipment, machinery, tools, apparatus, services, all state workmen's compensation and unemployment compensation taxes incurred in the performance of the Contract, means of transportation for and complete

Construction of: MCCH - Sally Port Gate Installation, Project Number 2020-043446, in the County of

Palm Beach, State of Florida; and

WHEREAS, it was a condition precedent to the submission of said bid that a certified check cashier's check, money order or bid bond in the amount of five percent (5%) of the base bid be submitted with said bid as a guarantee that the bidder would, if given a Notification from Owner, enter into a written contract with the

County, and furnish a public construction bond in an amount equal to one hundred (100%) of the total

Contract, within fourteen (14) consecutive calendar days after the County issues the Notification from

Owner.

NOW THEREFORE, THE CONDITIONS OF THIS OBLIGATION ARE SUCH that, if the bid of the "Principal" herein is accepted and said "Principal", within fourteen (14) consecutive calendar days after written notice being given of such acceptance, (i) enter into a written contract with the County and (ii) furnishes a public construction contract bond in the amount equal to one hundred percent (100%) of the total contract amount and in a form satisfactory to the County, then this obligation shall be void. If the

Principal fails to complete (i) and (ii) above, the sum herein stated shall be due and payable to the "County", and the "Surety" herein agrees to pay said sum immediately upon demand of the "County", in good and lawful money of the United States of America, as liquidated damages for failure of said "Principal".

Bid Bond Must Contain Original Signatures. No Copies Will Be Accepted.

Form Rev. 4/13/21 Bid Bond - NonFederal

DATE:

IN WITNESS WHEREOF, the said as "Principal" herein, has caused these presents to be signed in its name, by its

, and attested by its under the corporate seal, and the said as "Surety" herein, has caused these presents to be signed in its name, by its

, and attested by its corporate Seal, this day of , A.D., 20 .

ATTEST:

Print Name

TITLE:

(SEAL)

(Contractor Name)

By:

(Signature)

Print Name and Title:

ATTEST:

Print Name

TITLE:

(SEAL)

(Surety Name)

By:

(Signature)

Print Name and Title:

Bid Bond Must Contain Original Signatures. No Copies Will Be Accepted.

IFQ/B ATTACHMENT C

PROJECT REQUIREMENTS

Annual Contract – Low Voltage

Contact: Rocky Roque, Capital Improvements Division Phone: (561) 233-2050 Project Title: MCCH - Sally Port Gate Installation Project #: 2020-043446 Project Location: 205 North Dixie Hwy, West Palm Beach, FL

1. GENERAL

a. The work covered by this Request for Quote consists of, but is not limited to, the furnishing of all labor, equipment, devices, tools, materials, transportation, professional services, supervision, drawings, permitting and all miscellaneous requirements to perform all operations necessary to accomplish the work set forth below and shall be considered part of the Scope of Work.

b. Please reference the Annual Contract – Low Voltage for additional requirements.

c. Work to be completed during the hours of 7:00 am to 5:00 pm, Monday through

Friday.

d. Contractor shall contact the Project Manager, within seventy-two (72) hours of

Notice to Proceed to establish scheduling etc. required for project implementation.

e. Work to be completed within sixty (60) days from permit issuance. Permit application, if required, is to be submitted by Contractor within five (5) days of Notice to Proceed and due diligence exercised to address all Building Department comments.

f. Liquidated damages will accrue in the amount of $80 per day.

g. The Contractor will provide a Certificate of Occupancy or Certificate of Completion, as appropriate, obtained from the proper Building official, prior to processing of final payment.

h. Contractor is responsible for obtaining all measurements during the site inspection.

2. SCOPE OF WORK

a. Provide and Install as a turnkey project a new vehicular control system complete with movable gates, motors, four (4) loop detectors, photoelectric reflective sensors with hood, motor controllers, and all associated infrastructure to support and integrate to existing OnGuard GUI system as shown in Exhibits “1” and “2”.

b. Provide and Install Pedestal Pro- model:72-9C-D (or PBC approved equal) with Lando- model:CS-20X14E (or PBC approved equal) housings at entry and exit.

c. Provide and Install two (2) Lenel Reader Boards Dual Reader Interface Module model:DRI-LNL-1320 (or PBC approved equal).

d. Provide and Install two (2) HID model: RPK40 (or PBC approved equal) Card Readers and Commend Video Intercoms model: ES931ACW (or PBC approved equal), one on each pedestal.

e. Provide and Install Awid model: LR-3000 (or PBC approved equal) UHF Long Range Reader on each pedestal, as shown on Exhibit “3”.

f. New equipment shall interface with existing card access and intercom infrastructure and include new icons with OPEN/STOP/CLOSE options on the OnGuard GUI system as well as separate control station for gate with OPEN/STOP/CLOSE options in Detention Command Center Room # CBD05.

g. All accessories required to make a complete turn-key system are to be included.

3. SUBMITTALS

All submittals shall be sent to the Project Manager for approval. This includes, but is not limited to, products to be used, methods of installation and requests for information and/or clarification. All submittals must be made by the Contractor and must include all details necessary for the Project Manager and Palm Beach County to make any necessary determinations. A transmittal form must be included which clearly requests data or information and deviations from the contract requirements for which approval is being requested. Failure to provide sufficient information will result in the rejection of the submittal. Where the specifications do not specify a brand name product or where a substitution of a product is not specifically prohibited, the Contractor shall submit their selected products for approval by the Project Manager. Such submittals shall include as much detail, and in a format, as required by the Project Manager, so as to allow the Project Manager to evaluate the proposed substitution.

4. MATERIALS

a. All material shall meet or exceed Florida Building Code and product submittals shall be reviewed and approved by the Owner’s Representative prior to ordering.

b. Materials shall be delivered in their original, unopened packages, and protected from exposure to the elements. Damaged or deteriorated materials shall not be used.

5. TEMPORARY PROTECTION

The Contractor shall protect all workers, staff and the general public from injury. The Contractor shall coordinate and schedule all work with the Project Manager.

6. PROJECT CONDITIONS

Contractor is to coordinate all space and security requirements with the Project Manager. A construction schedule shall be submitted for review and approval prior to pre-construction meeting, including a start date, substantial completion date, and work plan defining which openings will be scheduled on what day. The Contractor shall conduct all work so as to cause the least interference possible with the normal activities of the operations of the facility and surrounding areas. Any damage caused by Contractor (including landscaping and irrigation) shall be the responsibility of the Contractor to repair and return to its original state.

7. PREPARATION

It shall be the responsibility of the Contractor to prep the site at the construction locations.

8. EXAMINATION

Report to the Project Manager, in writing, any imperfections, unacceptable conditions and/or corrections required to be made before commencing work. Any items not identified, documented and reported to PBC in writing, will become part of the contractors’ scope. All other items identified in writing, if approved, shall result in a change order.

9. INSTALLATION

All materials shall be installed in strict accordance with Manufacturer’s written instructions and recommendations. All work shall be done in conformance with applicable Federal, State and Local codes, and established standards.

10. WARRANTY

Contractor warrants all equipment, materials and labor furnished or performed against defects in design, materials and workmanship for a period of twelve (12) months from substantial completion.

11. CLEAN UP

Remove all waste materials, tools and equipment from job site daily. Thoroughly clean the entire job area prior to requesting final inspection.

12. SECURITY

All bidders must have badged employees as identified below prior to commencement of work.

This project is subject to: [ ] Critical Facilities Background Check

[X] CJI Facilities Background Check [ ] No Background Check

EXHIBIT "1"

Textbox DISCLOSURE WARNING. THIS DOCUMENT IS EXEMPT AND CONFIDENTIAL UNDER SEC. 119.071, FLORIDA STATUTES. ANY ENTITY OR PERSONS RECEIVING SUCH INFORMATION SHALL MAINTAIN THE EXEMPT STATUS OF THE INFORMATION UNLESS OTHERWISE AUTHORIZED BY THE COUNTY.

THESE DOCUMENTS SHALL NOT BE DISTRIBUTED, LOANED OR COPIED WITHOUT THE WRITTEN PERMISSION OF THE COUNTY IN ACCORDANCE WITH THE RELEVANT PROVISIONS OF FLORIDA LAW. THE COUNTY MUST BE ADVISED IMMEDIATELY AS TO ANY CHANGES IN CUSTODIAN FROM THOSE PERSONS LISTED IN CORRESPONDENCE FOR ORIGINAL DISTRIBUTION, IF THE DOCUMENTS ARE LOST OR STOLEN, OR IF THERE IS IMPROPER DISCLOSURE OR UNAUTHORIZED USE OF THE INFORMATION IN THE DOCUMENT. UPON COMPLETION OF USE, WORK, PROJECT, OR CONTRACT, THE CONTRACTOR/CONSULTANT SHALL SHRED OR BURN ANY DUPLICATE RECORDS.

Textbox

DISCLOSURE WARNING. THIS DOCUMENT IS EXEMPT AND CONFIDENTIAL UNDER SEC. 119.071, FLORIDA STATUTES. ANY ENTITY OR PERSONS RECEIVING SUCH INFORMATION SHALL MAINTAIN THE EXEMPT STATUS OF THE INFORMATION UNLESS OTHERWISE AUTHORIZED BY THE COUNTY.

THESE DOCUMENTS SHALL NOT BE DISTRIBUTED, LOANED OR COPIED WITHOUT THE WRITTEN PERMISSION OF THE COUNTY IN ACCORDANCE WITH THE RELEVANT PROVISIONS OF FLORIDA LAW. THE COUNTY MUST BE ADVISED IMMEDIATELY AS TO ANY CHANGES IN CUSTODIAN FROM THOSE PERSONS LISTED IN CORRESPONDENCE FOR ORIGINAL DISTRIBUTION, IF THE DOCUMENTS ARE LOST OR STOLEN, OR IF THERE IS IMPROPER DISCLOSURE OR UNAUTHORIZED USE OF THE INFORMATION IN THE DOCUMENT. UPON COMPLETION OF USE, WORK, PROJECT, OR CONTRACT, THE CONTRACTOR/CONSULTANT SHALL SHRED OR BURN ANY DUPLICATE RECORDS.

DISCLOSURE WARNING. THIS DOCUMENT IS EXEMPT AND CONFIDENTIAL UNDER SEC. 119.071, FLORIDA STATUTES. ANY ENTITY OR PERSONS RECEIVING SUCH INFORMATION SHALL MAINTAIN THE EXEMPT STATUS OF THE INFORMATION UNLESS OTHERWISE AUTHORIZED BY THE COUNTY.

THESE DOCUMENTS SHALL NOT BE DISTRIBUTED, LOANED OR COPIED WITHOUT THE WRITTEN PERMISSION OF THE COUNTY IN ACCORDANCE WITH THE RELEVANT PROVISIONS OF FLORIDA LAW. THE COUNTY MUST BE ADVISED IMMEDIATELY AS TO ANY CHANGES IN CUSTODIAN FROM THOSE PERSONS LISTED IN CORRESPONDENCE FOR ORIGINAL DISTRIBUTION, IF THE DOCUMENTS ARE LOST OR STOLEN, OR IF THERE IS IMPROPER DISCLOSURE OR UNAUTHORIZED USE OF THE INFORMATION IN THE DOCUMENT. UPON COMPLETION OF USE, WORK, PROJECT, OR CONTRACT, THE CONTRACTOR/CONSULTANT SHALL SHRED OR BURN ANY DUPLICATE RECORDS.

DISCLOSURE WARNING. THIS DOCUMENT IS EXEMPT AND CONFIDENTIAL UNDER SEC. 119.071, FLORIDA STATUTES. ANY ENTITY OR PERSONS RECEIVING SUCH INFORMATION SHALL MAINTAIN THE EXEMPT STATUS OF THE INFORMATION UNLESS OTHERWISE AUTHORIZED BY THE COUNTY.

THESE DOCUMENTS SHALL NOT BE DISTRIBUTED, LOANED OR COPIED WITHOUT THE WRITTEN PERMISSION OF THE COUNTY IN ACCORDANCE WITH THE RELEVANT PROVISIONS OF FLORIDA LAW. THE COUNTY MUST BE ADVISED IMMEDIATELY AS TO ANY CHANGES IN CUSTODIAN FROM THOSE PERSONS LISTED IN CORRESPONDENCE FOR ORIGINAL DISTRIBUTION, IF THE DOCUMENTS ARE LOST OR STOLEN, OR IF THERE IS IMPROPER DISCLOSURE OR UNAUTHORIZED USE OF THE INFORMATION IN THE DOCUMENT. UPON COMPLETION OF USE, WORK, PROJECT, OR CONTRACT, THE CONTRACTOR/CONSULTANT SHALL SHRED OR BURN ANY DUPLICATE RECORDS.

AWID's LR-3000™ Long-Range Reader is an Ultra-High-Frequency (UHF) tag and card reader used in RFID applications like gate access for vehicles and physical access for people. Its electronics and antenna are integrated in a single compact enclosure.

The LR-3000 is optimally designed for Automatic Vehicle Identification (AVI) and

Access Control applications such as gate control in a parking facility. It also provides identification and access for people at doorways, wheelchairs at elevators, and gurneys in hospital entrances. The LR-3000 Reader assures security by use of AWID's proprietary encryption for communications between the reader and its UHF vehicle tags and hand-held cards. The LR-3000 reader has two LEDs – steady red to indicate

DC power, and blinking green when a tag is presented. The LR-3000 reader is suitable for outdoor applications; it may be installed with exposure to the environment.

FEATURES

∙ Longer reading distance ...

Up to 25 feet between reader and tag

· Small, attractive reader ...

Single unit with antenna, 9.8"x9.8"x1.3"

· Easy reader installation ...

No reader programming, simple wiring

· Wide selection of credentials ...

Varied vehicle tags and hand-held cards

· Unlimited tag or card life ...

Passive, battery-free credentials

· Data output to fit the system ...

Selectable read repeat rate

· No interference between readers, and no cross-reading between lanes ...

Programmable RF field strength

· RF transmission only as needed ...

Optional buried loop arms the RF circuit

· LED status indicators ...

Red for power, green for tag reading

· LR-3000 mixes with other readers ...

Same code format as proximity readers

· Easy interfacing to control systems ...

Both Wiegand and RS-232 data output

· Complies with certifications ...

FCC Part 15; IC; RoHS

· Ideal upgrade from old systems ...

Hands-free car ID; cards for people ID

· Eliminates stop-and-wait entry ...

Cars may continue moving past reader

· No need to add protective housing ...

Protection class IP65 for outdoor sites

· Easy to buy and own ...

Installer needs no FCC registration

The LR-3000 offers price:performance advantage over conventional long-range proximity card and active-tag RF systems. The LR-3000 can be combined with

AWID's uAxcess door access readers, allowing the same hand-held card to be used for both vehicle parking access at the gate, and door access for people in the building.

The LR-3000 operates in the license-free 902-928 MHz UHF band. It combines effective UHF technology with economical passive tags and cards, field-programmable read repeat rate and RF field strength, and simultaneous Wiegand and

RS-232 data outputs. It can be interfaced with all standard access control and AVI systems. The LR-3000 offers an impressive combination of single-unit construction, small size, and attractive appearance. Tag reading distance is commonly up to 25 feet and sometimes more depending on reader mounting, credential type and environment.

LR-3000

UHF Long-Range Reader

EXHIBIT "3"

LR-3000™

UHF Long-Range Reader

OPERATING CHARACTERISTICS

Reading Distance:

Tags and cards, up to 25 feet (7.6 meters)

Frequency Band:

902 to 928 MHz; Frequency Hopping technology

Antenna Output:

Circular-polarized RF field

Indicators:

2 LEDs -- Red for power; Green for tag reading

Power Supply: Separate for each long-range reader

7 to 15 volts DC, linear rated, regulated output

At 12 VDC, rated for 2 amperes or more

Separate, independent, dedicated to each reader

Communications Protocols:

Wiegand and RS-232, simultaneous outputs

Code Formats:

Determined by AWID's tags & cards; 26 to 50 bits

Cables: All cables MUST be overall-shielded

Power -- 2 conductors, 18 gauge, shielded

Data -- 3 conductors, 22 gauge, shielded

Stranded, color-coded, not twisted pairs

Up to 500 feet for Wiegand; 75 feet for RS-232

Field-Programmable Features:

Read repeat rate; RF power level

PHYSICAL CHARACTERISTICS

Dimensions:

9.8 x 9.8 x 1.3 inches (25 x 25 x 3.3 cm)

Weight:

38.4 oz (1.09 kg)

Material (Color):

ABS enclosure (white); aluminum back-plate

Cable (Integrated with Reader):

10 conductors, 32 inches (81 cm) long

Overall shielded, plastic jacket

Mounting (Supplied by Installer):

Pan-and-tilt adjustable aiming, min. 6 inches long

ENVIRONMENT

Operating Temperature:

-35°C to +65°C (-31°F to +150°F)

Operating Humidity:

0% to 95% non-condensing

Protection Class:

IP65 Weatherproof

Avoiding Interference:

Optimize reader performance by avoiding sources of RF – fluorescent and other arc lighting, UHF transmitters, other UHF readers.

CERTIFICATION

FCC Part 15; IC; RoHS; ETL

18300 Sutter Blvd, Morgan Hill, CA 95037

Tel: (408) 825-1100 Fax: (408) 782-7402 http://www.awid.com

ACCESSORIES AND SUPPLIES

· LR-reader test/demo kit -- A requirement for all installers. An effective way to demonstrate the

LR-3000, to prove its operation, to measure its performance, to locate tags, and to aim the reader.

A one-time purchase for installers.

· Power supply -- Each LR-3000 requires a separate, independent, dedicated power supply.

Ask AWID for specifications. AWID offers PS-123.3A-0-0 plug-in DC module.

· Cable for power and data -- Correct cable assures good reader performance. Ask AWID for specifications.

· Mounting devices -- Ask your supplier about poles, posts, pedestals, clamps, arms, etc.

· System components -- Ask your supplier about the access control package, gates, vehicle sensors, bollards, traffic barriers, and other components.

· Installation and operation -- Download additional information from www.AWID.com.

CREDENTIAL OPTIONS

· Vehicle-mounting tags -- For permanent or movable applications, inside or outside vehicles.

Types are tags for Windshield (WS-UHF), Rearview Mirror (RV), Sunvisor (VT), Sideview Mirror

(SV) and Metal-Mount (MT-UHF); also Portable tag (PT), Hangtag (HT), and Supertag (ST).

· Hand-held cards -- For presenting to reader. Cards: Clamshell (CS-UHF) and Graphics (GR-UHF).

Tags: Keytag (KT-UHF) and Hangtag (HT). Use these cards and tags with uAxcess readers.

Ask AWID about tag selection and mounting methods.

DISCLAIMER: Specifications are subject to change without notice. AWID reserves the right to make changes to improve performance without impacting form, fit or function. The LR-3000 model designations are Trademarks of Applied Wireless Identifications Group, Inc.

All other trademarks are property of their respective owners.

HOME (/) / CREDENTIALS (/AC-PRODUCTS/CREDENTIALS) / LR/UHFYOU ARE HERE:

LR/UHF

LR/UHF

(/credentials/credentials-lr-uhf/559-lr-ws-uhf)

WINDSHIELD TAG

• Adheres permanently inside windshield

• Reading distance up to 25 feet (7.6 meters)

• Batteries not needed - passive tag technology

• Secure - for one-time use - shows tampering

READ MORE: WS-UHF (/CREDENTIALS/CREDENTIALS-LR-UHF/559-LR-WS-UHF)

WS-UHF (/credentials/credentials-lr-uhf/559-lr-ws-uhf)

RV-UHF (/credentials/credentials-lr-uhf/557-rv-uhf)

Page 1 of 4LR/UHF

7/20/2020http://awid.com/credentials/credentials-lr-uhf

(/credentials/credentials-lr-uhf/557-lr-rv-uhf)

REARVIEW MIRROR TAG

• Adheres permanently on shell of rear-view mirror

• Reading distance up to 20 feet (6.1 meters)

• Suitable for other locations, even outside vehicles

• Secure – for one-time use – shows tampering

READ MORE: RV-UHF (/CREDENTIALS/CREDENTIALS-LR-UHF/557-RV-UHF)

METAL-MOUNT TAG

• Attaches to metal surface, or any other material

• Reading distance up to 15 feet (4.6 meters)

• Fastened by screws, rivets, adhesive, cable ties, et

• For cars, trucks, wheelchairs, forklifts, containers

MT-UHF (/credentials/credentials-lr-uhf/556-mt-uhf)

SV-UHF (/credentials/credentials-lr-uhf/598-sv-uhf)

Page 2 of 4LR/UHF

(/credentials/credentials-lr-uhf/598-lr-sv-uhf)

SIDEVIEW MIRROR TAG

• Adheres permanently on shell of side-view mirror

• Reading distance up to 25 feet (7.6 meters)

• Out of sight on bottom edge of outside mirror

• Secure - tag is disabled when removed

(/credentials/credentials-lr-uhf/599-pt-uhf)

PORTABLE TAG

• Use like a toll highway tag inside vehicles

• Reading distance up to 15 feet (4.6 meters)

• Attach by hook-and-loop strip, move to other cars

• Use with readers installed above or beside lane

PT-UHF (/credentials/credentials-lr-uhf/599-pt-uhf)

Page 3 of 4LR/UHF www.commend.comDatasheet Version 1.0/0110 | Errors and omissions excepted | Products may change in the interest of technical improvements without notice. P 1 | 4

Datasheet

3 Gang IoIP (Intercom over IP) Tamper/Weather resistant substation connects directly to IP networks. It can be used where additional wiring is inconvenient and both attractive appearance and extreme durability are important.

ES931ACW

–– Direct network connection with Static or Dynamic IP –– Full open duplex communications –– Power over Ethernet (POE) supported –– Rugged 11 gauge stainless steel faceplate –– True tamper resistant construction –– Rugged call button –– Weather resistant –– Sensitive electret microphone –– Mounts in industry standard 3 gang switch backbox –– Mic Open LED –– Full Supervision (speaker, microphone, station electro-nics, cable, network)

–– Wide angle camera (up/down angle adjustable)

ES3GBB

–– 3 gang backbox –– powder coated gray

ES3GRH

–– 3 gang rain hood –– powder coated gray

ES931ACW

3 Gang IoIP Substation ES931ACW www.commend.com

Operating temperature range: -25°C to +50°C (-13°F to 122°F)

Storage temperature range: -25°C to +50°C (-13°F to 122°F)

Relative Humidity: up to 95% not condensing

Call button: Possibility for connection of 3 single buttons

Microphone input: for electret microphone or dynamic microphone

Mic Input: nominal level 2.8 mV on 3.3 kW (Mic-feeding voltage 2.5 V)

Connection for loudspeaker: 2.5 W at 4W / 1.5 W at 8W

LS-Output: max 3.5Veff (LS-Pot max, Vol. 9)

Ext. microphone,loudspeaker: Possibility for connection of e.g. headset, handset

EP Output: max 850 mVeff (Vol. 9), Ri = 200W EM Input: nominal level 14mV on 3.3W

( Mic-feeding voltage 2.5V)

Line input: for feed-in of audio (e.g.music, radio conference)

Line-Input: nominal level 0 dBu 0.775 V at 10 kW

Amplifier: Built-in amplifier class “D” with 2.5 W

Status indication: Possibility for connection of a LED 6 mA

Inputs: 3 inputs for floating contacts (recognizes 5 input states)

Outputs: 2 relay outputs (changeover contacts) 30 V / 1 A: 100,000 make-and-break cycles

Frequency range: 50 - 16,000 Hz (depending on connected loudspeaker)

Connection: pluggable screw terminals -IP Uplink/Downlink: shielded RJ45 modular jacks -Expansion plug for e.g. EB2E2AHE

Cabling: min. Cat. 5

Power supply: 12-24 VAC or 15-35 VDC, 500 mA or PoE

PoE (power over ethernet): IEEE 802.3af standard Power consumption of the terminal device:

Class 0 (0.44 W to 12.95 W)

Protocol: IoIP-Protocol based on UDP/IP

Data rate: 2 x 10/100 MBit/s (full / half duplex)

Measurements: 6.56 x 4.93 see drawing page 3 benefits

• Communication via data networks- no additional cabling required

control of barriers

tion is possible

• Supports DSP-functionlities such as Open Duplex®, Audio

Monitoring, Loudspeaker-/Microphone Surveillance, etc.

configuration line length in lan The maximum line length of Cat 5 cabling in a LAN is 100 m (328

ft) - e.g. from switch to ET908.

Datasheet Version 1.0/0110 | Errors and omissions excepted | Products may change in the interest of technical improvements without notice. P 2 | 4

Datasheet

Technical Data – Benefits

Extent of Supply

• Intercom Terminal camera Technical data Model Axis M3114-R: 1 MP / HDTV 720p

Image Sensor 1/4“ progressive scan RGB CMOS

Lens 2.9 mm: 80° view*, F2.0 M12 mount *horizontal angle of view

Light sensitivity 1 - 100000 lux, F2.0

Shutter time 1/24 500 s to 1/6 s

Camera angle adjustment Vertical tilt 0 - 30 °

Video compression H.264 (MPEG-4 Part 10/AVC) Motion jpeg

Power Power over Ethernet IEEE 802.3af Class 1, max.

3.2W

Connectors RJ-45 variants: rugged, female RJ-45 10BASE-T/100 BASE-TX M12 variants:rugged female, All connectors support Power over Ethernet

Precautions / mounting info

• When opening the stations ESD precautions must be observed.

• The stations may only be opened by authorized service engineers.

• Do not expose the station to extreme temperature (below -25°C or above +50°C / -13°F to +122°F)

• The stations are designed especially for building into Ameri-can “3 gang” double deep switch boxes. Box and mounting screws are not included in the extent of supply.

• For stations to be mounted in outdoor areas, the screws must be closed with a sealing compound.

intercom technical data

System Requirements:

*Intercom station will detect as ET908 in programming software www.commend.comDatasheet Version 1.0/0110 | Errors and omissions excepted | Products may change in the interest of technical improvements without notice. P 3 | 4

Datasheet

Installation Connection diagram www.commend.comDatasheet Version 1.0/0110 | Errors and omissions excepted | Products may change in the interest of technical improvements without notice. P 4 | 4

DatasheetDatasheet aUstRIa CROatIa seRBIa sLOVeNIa

RUssIa

Commend Österreich Gmbh tel. +43-1-715 30 79 www.commend.at

FRaNCe Commend France s.a.s.

tel. +33-149 18 16 40 www.commend.fr

NetheRLaNDs BeLGIUM

Commend Nederland B.V.

tel. +31-76-200 01 00 www.commend.nl

ItaLY Commend Italia s.r.l.

tel. +39-035-95 39 63 www.commend.it sWeDeN NORWaY FINLaND

DeNMaRK IsLaND

JNt sound system aB tel. +46-8-99 30 60 www.jnt.se

GeRMaNY LUXeMBOURG

RUssIa schneider Intercom Gmbh tel. +49-211-88285-333 www.schneider-intercom.de

POLaND C&C Partners telecom sp.z o.o.

tel. +48-65-525 55 55 www.ccpartners.pl

UNIteD KINGDOM IReLaND

Commend UK Ltd tel. +44-1279-45 75 10 www.commend.co.uk sWItZeRLaND Commend aG tel. +41-44-955 02 22 www.commend.ch europe aUstRaLIa NeW ZeaLaND

Commend australia tel. +61-3-9755-3947 www.commend.com.au

Oceania sINGaPORe Commend Business hub asia Isolectra Far east Pte. Ltd tel. +65-6272-2371 www.commend.com.sg

ChINa Commend Business hub China Isolectra China tel. +86-21-52 13 19 28 www.isolectra.com.cn

MaLaYsIa Commend Business hub Malaysia Isolectra (M) sdn Bhd tel. +603-7846-9988 www.isolectra.com.my asia

IsRaeL sberlophone Ltd tel. + 972-4-834 10 32 www.sberlophone.co.il

Middle east

Usa CaNaDa

LatIN aMeRICa

Commend Inc.

tel. +1-201-529-2425 www.commendusa.com america

Commend International Gmbh tel. +43-662-85 62 25 www.commend.com

Other countries sLOVaKIa CZeChIa

Commend slovakia spol. s r.o.

tel. +421-2-58 10 10 40 www.commend.sk sPaIN PORtUGaL

Commend Iberica s.L.

tel. +34-91-395 24 98 www.commend.es

COMMeND a strong Partner Network | Worldwide

Pedestal

Brand Name: PEDESTAL PRO Manufacturer: Pedestal PRO Manufacturer Part Number: 72-9C-D Product Model : 72-9C-D Product Type: Mounting Pole

UPC 855614007293

Weight: 45 lbs

Color: Black Wrinkle Depth: 13" Height: 72" Weight (Approximate): 45 lb

Device Support •Access Control System •Camera •Card Reader •Intercom System •Keypad •Telephone Entry System

HOUSNG, LANDSCPE, 20X14X6, BLK

Pedestal Pro, Llc

Model #: LANDO-CS-20X14-E

PHYSICAL ACCESS SOLUTIONS

hidglobal.com multiCLASS SE® Readers

HIGHLY ADAPTABLE AND SECURE HIGH FREQUENCY

ACCESS CONTROL SOLUTION

� Powerfully Secure – Provides layered security beyond the card media for added protection to identity data using SIOs.

� Adaptable – Interoperable with a growing range of technologies and form factors including mobile devices utilizing Seos™.

� Interoperable – Open Supervised Device Protocol (OSDP) for secure, bidirectional communication.

� Streamlined Migration – Simultaneous support for 125 kHz HID Prox®, AWID and EM4102 for seamless migration; field programmable for secure upgrades and extended lifecycle.

POWERFULLY SECURE:

� Multi-Layered Security – Ensures data authenticity and privacy through the multi-layered security of HID’s SIO.

� EAL5+ Certified Secure Element Hardware – Provides tamper-proof protection of keys/cryptographic operations.

HIGHLY ADAPTABLE:

card technologies.

� Upgradeable Hardware Connection – Allows all Wiegand-based communication readers to expand communication capabilities to OSDP, Hi-O and other bidirectional protocols.

� Field Programmable Readers – Provides secure upgrades for migration and extended lifecycle.

� Customization and management from a central location – Enables organization to make changes and manage all attached OSDP readers over RS485 wiring.

SUSTAINABILITY AND MANAGEMENT:

� Intelligent Power Management (IPM) – Reduces reader power consumption by as much as 75% compared to standard operating mode.

� Recycled Content – Contributes toward building LEED credits.

INTEROPERABLE:

� SIO Media Mapping – Simplifies deployment of third-party objects to multiple types of credentials.

DESFire EV1 credentials.

HID Global’s iCLASS SE® platform goes beyond the traditional smart card model to offer a secure, standards-based and flexible platform that has become the new benchmark for highly adaptable, interoperable and secure access control solutions.

multiCLASS SE® readers simplify migration from legacy technologies with support 125 kHz for HID Prox, Indala, AWID and EM4102, and provide customers the assurance that their existing investments can be leveraged to enhance their system as business requirements change. The technology-independent readers also support iCLASS® Seos™ and iCLASS SE credential platforms, as well as standard iCLASS, MIFARE and

MIFARE DESFire EV1 with custom data models…