2-4-C-35-24 OLATHE PILOT PROJECT BID DOC FINAL.pdf

City of Olathe, Kansas Signage & Wayfinding Plan for Parks, Trails, and Unique Places:

Pilot Project (Frontier Park) Bid Document

AUGUST 27, 2025 | FINAL

PREPARED BY

TABLE OF CONTENTS

Fabricator Performance & Material Requirements

Bid Requirements

Typography, Color, & Symbols

Sign Family

Design Intents

Sign Location Plan & Message Schedule

FABRICATOR PERFORMANCE & MATERIAL REQUIREMENTS

This document has been assembled by Tangram Design, LLC (Tangram) for the City of Olathe, Kansas (Owner) with the expectation that the fabricator shall meet the following quality and performance requirements. The acceptance of these drawings by the Fabricator constitutes agreement to comply with the following conditions. The Owner will hold the Fabricator to these requirements as part of their contract obligations. The City of Olathe may establish a price agreement for future projects, contingent upon the contractor’s satisfactory performance on this project.

1.0 GENERAL

1.1 Proprietary Information Non-Disclosure Agreement

The ideas, designs, arrangements, plans, and related content within this document are the intellectual property of Tangram and are provided solely for the purposes of bidding and fabrication of the signage for the Owner. These designs may not be reused, reproduced, or adapted by the Fabricator for any other purpose without prior written approval from both the Owner and Tangram.

Additionally, any images or representations of the design work in this document used by the Fabricator for promotional, portfolio, or publication purposes must include proper credit indicating Tangram as the Designer and Olathe as the Owner. The Owner may impose additional restrictions or requirements, which the Fabricator is also responsible for observing.

1.2 Design Intent Drawings

The “design intent” drawings contained in this document are for the sole purpose of expressing visual design intent and are not intended for construction purposes. All aspects of fabrication, installation, and any resulting working drawings, shop drawings, submittals and contract documents are the responsibility of the Fabricator. Within the design intent drawings:

Prior to execution of the contract, Fabricator shall carefully review all the Contract Documents, Design Intent Drawings, Specifications, and/or instructions for any conflicts or ambiguities. Fabricator will identify any conflicts or ambiguities in writing to Owner and Tangram prior to execution of the agreement.

2.0 PRE-FABRICATION REQUIREMENTS

2.1 Proposal

The Fabricator shall base their proposal on the performance of all items of service including labor, operations, materials, accessories, incidentals, services and equipment indicated, specified, mentioned, scheduled or implied to complete fabrication and installation of the specified work. Full compliance with the these Fabricator Performance and Material Requirements will be required.

Fabricator proposes and agrees to perform all work and/or services as specified in the bid and design intent documents for the prices and within the times indicated in the bid and in accordance with the other terms and conditions of the Contract. Fabricator does not consider that any further examinations, investigations, explorations, tests, studies, specifications, or data is necessary for the determination of this bid for performance of the work and/or services. Fabricator is satisfied as to the general, local and site conditions that may affect cost, progress, and performance of the work and/or services.

It is the responsibility of each Fabricator to verify the availability of material(s), delivery schedules, fabrication and manufacturing schedules and other pertinent data prior to submission of their proposal; and the responsibility of the successful respondent to provide same after award of the project. It is the responsibility of the respondent to notify the Owner immediately if material(s) specified are discontinued, replaced, or not available for an extended period of time. The Owner reserves the right to charge back additional costs, including but not limited to, freight, special handling, and purchase price difference due to delays, etc., to the successful respondent when items are not supplied as proposed.

The Fabricator is encouraged to make recommendations for specific changes if they will improve the quality or cost-effectiveness of fabrication while preserving Tangram’s visual design intent. However, any such recommendations must be approved in writing by the Owner and Tangram at the time of bid. Should the Fabricator be contracted based on a proposal that assumes substitutions that have not been properly approved, the Fabricator shall be responsible for providing all elements as originally indicated at their own expense.

Fabricator has given the Owner and Tangram written notice of all conflicts, errors, ambiguities or discrepancies that the respondent has discovered in the bid documents, and the written resolution thereof by the Owner and Tangram is acceptable to respondent. The bid documents are generally sufficient to indicate and convey understanding of all terms and conditions for the performance of the work and/ or services for which this bid is submitted.

2.2 Performance

The Fabricator shall and will, in good quality manner, do and perform all work and furnish all supplies and materials, machinery, equipment, facilities, and means, except as herein otherwise expressly specified, necessary or proper to perform and complete all the work required, within the time specified. The Fabricator shall furnish, erect, maintain, and remove such construction plant and such temporary works as may be required. The Fabricator shall observe, comply with, and be subject to all terms, conditions, requirements, and limitations of the contract and specifications, and shall do, carry on, and complete the entire work to the satisfaction of the Owner.

Fabricators are expected to examine all Drawings, Specifications, instructions and/or requirements of this design intent document and corresponding documents. Failure to do so will be at the respondent’s risk. All referenced documents must be considered in preparation of Fabricator’s proposal. The Owner and Tangram assume no responsibility for errors or misinterpretations resulting from the use of the bid or design intent documents.

2.3 Subcontracting

The Fabricator may utilize the services of specialty subcontractors on those parts of the work that under normal contracting practices are performed by specialty fabricators. The Fabricator must be able to perform a majority of the work at their own facility. Subcontractors shall have a supportive role to the project and should not individually or collectively have a higher percentage of work to perform than the Fabricator. The Fabricator shall be as fully responsible to the Owner for the acts and omissions of their subcontractors, and of persons either directly or indirectly employed by them, as the Fabricator is for the acts or omissions of persons directly employed by the Fabricator.

2.4 Shop Drawings

The Fabricator shall submit for review and approval shop drawings of all fabricated items, product data and samples to the Owner and Tangram. This submission shall consist of detailed drawings that indicate all materials, finishes, construction details, lighting requirements, installation details, and artwork, including locations of all material seams. Drawings shall include elevations, plans, sections, and notes as required to clearly convey fabrication intent.

Tangram shall advise and review all shop drawing submittals for fidelity and conformance with the design intent drawings. Upon review, the Fabricator shall make all requested revisions and resubmit as required. A complete set of approved shop drawings must be received from both the Owner and Tangram before production may begin. Required submittals must be issued in adequate time to coordinate a two week review and approval process without delaying the project schedule.

2.5 Paint Samples

Paint and samples must be supplied to the Owner and Tangram for review and approval to ensure the color matches the approved colors.

Paint samples must include all paint layers that would be used on the final product (i.e. primer, topcoat, clear coat etc.) and be applied to the actual material that it is specified to be applied to in the document. Paint, vinyl samples and shop drawings are to be reviewed and approved by the Owner before full fabrication shall commence. If final product does not meet quality standards during the punch-list review, the sign type may have to be fixed or replaced.

3.0 FABRICATION & INSTALLATION REQUIREMENTS

3.1 Permitting & Regulation Compliance

The Fabricator is responsible for securing and paying for all permits, insurances, inspections, and tests required by governmental agencies.

The Fabricator is also responsible for verifying and ensuring compliance with all ADA, OSHA, environmental regulations, and all other applicable governing code requirements. Fabrication of signage shall be designed to meet local building codes including ASCE 7, Basic Wind speed of 130mph. All required resolutions or revisions to construction details must be approved by the Owner and Tangram prior to production.

3.2 Structural Requirements

The Fabricator shall follow Tangram’s drawings for exterior visual appearance, but designs of internal structure, engineered connections, mounting assemblies, and foundations are by the Fabricator. Structural design shall utilize self-supportive framing and prevent irregularities in exposed surfaces. The Fabricator shall provide the Owner and Tangram with calculations for all structural members and foundations and they must be sealed by certified engineers registered in the state of installation, prior to fabrication. The Fabricator shall provide the Owner and Tangram with a list of support and/or blocking requirements, and approximate weights for each element as required after final shop drawing approval. The Fabricator’s installation responsibilities include the provision of any required footings, anchor bolts, or fastenings.

All point-of-connection coordination is the responsibility of the Fabricator.

3.3 Labeling

Visible labels, manufacturer’s or otherwise, code permitting, shall not appear on any completed element. The placement of any required labels must be approved by the Owner prior to application and installation.

3.4 Artwork & Fonts

Tangram will provide the Fabricator with layout guidelines and electronic artwork as required, however all final copy layouts are the responsibility of the Fabricator. The Fabricator shall legally acquire, at their own expense, all project fonts from the specified distributors, as necessary. Tangram will not provide copies of licensed fonts.

The artwork in the design intents is not final. The final placement of the type must match the final artwork provided by Tangram. All letter forms shall match the final artwork and be aligned to maintain a base line parallel to the sign format. Margins must be maintained as specified by type grids in the drawings.

3.5 On-Site Coordination and Installation

All installation will be coordinated with the Owner. No installation shall be permitted without sign-off of construction and final location approval through the Owner. The Fabricator shall field verify all measurements indicated on drawings to establish correctness.

Project is located in Olathe, KS. Fabricator shall examine the site prior to executing this agreement so as to reasonably ascertain the nature of the work and the various conditions affecting the work. All locations shown in the enclosed location plans are approximate. The Fabricator is responsible for field verification and coordination of all final locations. The Fabricator shall notify the Owner and Tangram of any discrepancies between Tangram’s drawings, location plans, or message schedule, and field conditions prior to sign fabrication. All required resolutions or revisions to construction details or installation processes must be approved by the Owner and Tangram prior to production.

The Fabricator shall keep the site reasonably free from debris, trash and construction wastes resulting from the performance of the work.

The Fabricator shall be responsible for cleaning up all work areas upon the completion of work on a daily basis. Upon completion of the work, Fabricator shall remove all debris, trash, construction wastes, materials, equipment, machinery and tools arising from the work. All finish surfaces at the base of the sign (lawn, mulch, brick, etc.) shall be repaired to match existing finish grade.

All installed items shall be left in a clean and as-new condition. The Fabricator shall be fully responsible for the security and quality of all equipment, materials, and installed components until they have been reviewed and accepted by the Owner. All installations are to be level and plumb or will not be accepted. Immediately after erection, clean bolted connections and abraced areas of shop paint. Paint exposed areas with same paint of finish used for shop painting. If marred areas cannot be adequately touched up on site, the sign will be returned to the shop for controlled refinishing.

3.6 Inspection

At all reasonable times, Fabricator shall provide sufficient facilities for inspection of the work by Owner or Tangram at the site and at all locations where portions of the work are in progress or various stages of completion. When appropriate portions of the work are ready for inspection, Fabricator shall notify Owner and Tangram.

3.7 Safety

The Fabricator recognizes the importance of performing the work in a safe manner so as to prevent damage, injury or loss to (i) all individuals at the site, whether working or visiting, (ii) the work, including materials and equipment incorporated into the work or stored on-site or off-site, (iii) the work of others on the project, and (iv) all other property at the site or adjacent thereto. Fabricator assumes responsibility for implementing and monitoring all safety precautions and programs related to the performance of the work.

The Fabricator shall be responsible for providing barricade or protective coverings as necessary to safeguard the public and property during the performance and duration of their work. The Fabricator shall be fully responsible for any injuries to the public or damage to the buildings, site, and adjacent objects during installation.

4.0 MATERIAL STANDARDS

All materials, hardware, and finishes used to fabricate any and all components shall be new (i.e. not previously used or operated in any other application) from the most recent manufacturer’s production supply and free from any defects impairing strength, durability or appearance.

All letters forms shall be aligned to maintain a base line parallel to the sign format. Margins must be maintained as specified by type grids in the drawings.

4.1 Metals

Metals shall be the best commercial quality for the purposes specified and free from defects impairing strength, durability, or appearance.

All joints must be welded, filled, ground and sanded smooth prior to painting to insure an uniform surface. All sheet metal shall have brake formed edges with radii not greater than sheet thickness. All metals must be treated to prevent corrosion and staining of other finishes.

All aluminum & steel materials must be thoroughly sanded to remove oxidation and primed prior to painting to insure maximum paint adhesion.

4.2 Fasteners

All exposed fasteners shall be tamper-proof, resistant to oxidation and other corrosion, and painted to match adjacent surfaces. Concealed fasteners must be resistant to oxidation and other corrosion to prevent staining of other finishes. Nuts and bolts used on the footers and breakaway bases are to be anti-corrosive and galvanized.

4.3 Paints & Finishes

All paints and finishes shall match exactly the color, finish, and texture noted. The fabricator is to apply primer, top coat, and clear coat to all painted surfaces as follows. Use LVA117 as needed to speed up the drying process.

1. Matthews Paint 74-350/351 VOC Chrome Free Wash Primer

2. Matthews Paint Ultra Low VOC Topcoat.

3. Matthews Paint LV 228 Satin Clear Coat.

Unless otherwise noted, all pretreats, primers, coatings, and finishes shall be applied in strict accordance with the paint manufacturer’s specifications to provide the highest level of ultraviolet light resistance, weatherability, and overall longevity for both the materials indicated, and the environmental conditions of the final install locations. A polyurethane clear coating shall be applied to seal the paint and preserve the surface from wear and oxidation. All painted and wood surfaces shall be applied with Matthews Paint 42 228SP clear coat, satin finish.

Paints & finishes shall be warranted against color fading, UV damage, cracking, peeling, blistering, and other defects in materials or workmanship for a minimum of five years from date of Owner’s acceptance. All paints shall be evenly applied without pinholes, scratches, orange peeling, application marks, and other imperfections. Workmanship with finishes and formation of letters shall conform to the highest standards of the trade.

4.4 Izone Imaging

All panels must provide ultraviolet light resistance, weatherability, and overall longevity. Panels shall be warranted to withstand high traffic and extreme weather for a minimum of ten years from date of the Owner’s acceptance.

All Izone Imaging panels are to be supplied by Izone Imaging, contact Michael Dean (888) 464-9663.

If Izone materials are unavailable or an alternative high pressure laminate (HPL) product of equal or superior value is proposed by the Fabricator, the substitution must be submitted for review and approved by the Owner. Samples of the proposed product (matching the specified color and finish outlined in this document) must be submitted to the Owner for review and approval prior to final approval of the alternative product.

5.0 PROJECT COMPLETION

5.1 Review & Punch List

The Fabricator shall notify both the Owner and Tangram in writing when all work is completed. Upon notice, Tangram will review all work according to their contract with the Owner and prepare a punch list outlining incomplete or unsatisfactory items. The repair or replacement of work outlined on the punch list shall be coordinated between the Fabricator and the Owner. Fabricator shall correct any of the work that is found not to be in conformance at their own expense.

5.2 Correction of Work

All work, all materials whether incorporated in the work or not, all processes of manufacture, and all methods of construction shall be at all times and places subject to the inspection of the Owner and Tangram who shall be the final judge of the quality and suitability of the work, materials, processes of manufacture, and methods of construction for the purposes of which they are used. Should they fail to meet the Owner and Tangram’s approval, they shall be forthwith reconstructed, made good, replaced and/or corrected, as the case may be, by the Fabricator at the Fabricator’s expense. Rejected material shall immediately be removed from the site. If, in the opinion of the Owner and Tangram, it is undesirable to replace any defective or damaged materials, or to reconstruct or correct any portion of the work injured or not performed in accordance with the contract documents, the compensation to be paid to the Fabricator shall be reduced by such amounts as in the judgment of the Owner shall be equitable.

5.3 Final Deliverables

Upon the Owner’s acceptance of the work, the Fabricator shall provide the Owner with a complete service and maintenance manual for all products and finishes installed under their contract. This manual shall include, but is not limited to, product specifications such as manufacturer information, contact names and addresses, warranty information, technical data, and routine maintenance recommendations.

5.4 Warranties

All warranty periods shall begin on the date of the Owner’s acceptance of the work. All warranties shall include the materials and labor required to replace defective components. All installed elements shall be warranted against manufacturer defects for a minimum of one year, and all installed elements shall be warranted against defects in installation or workmanship for a minimum of three years.

SIGN TYPES

SIGN TYPE DESCRIPTION QUANTITY

A.3A* Freestanding Park Identification (Double-Sided) 2

C.1 Freestanding Parking Identification 4

D.1* Freestanding Directory 1

E.1* Freestanding Pedestrian Directional 1

F.1* Freestanding Trail Identification 1

F.2 Freestanding Trail Identification & Directional 1

G.1* Freestanding Mile Marker 5

H.2 Wall/Fence Mounted Field Identification 2

H.3 Pole Mounted Shelter Identification 2

*A full-scale prototype is required for this sign type. If approved, the prototype will be considered as part of the total quantity. Quantity shown includes prototype.

TYPOGRAPHY, COLORS,

& SYMBOLS

• These drawings are intended to illustrate design intent only and are not for construction. All final engineering and conditions of the project are the responsibility of the fabricator.� Shop drawings by the fabricator must be submitted for approval, prior to proceeding with fabrication.

• The quality of fit and finish on the final product must meet or exceed the requirements of these design intent documents. Any variations to design, materials, or fabrication methods must be approved by the Owner and Tangram.

• Colors shown are for reference only and are subject to the limitations of the printing process.

Refer to referenced color systems contained within these drawings for actual specifications.

• Scaled examples shown are for reference only, and do not necessarily reflect actual site conditions. Detailed site surveys are required prior to fabrication and installation.

• All locations shown are approximate. All final locations are to be determined during pre-installation site walk-thrus, prior to sign fabrication and must be approved by Owner.

• Messages shown in these drawings are for general reference only. Refer to message schedules for actual required messages.�

T A

N G

R A

M D

E S

IG

N

,L L

C

S A

N T

A F

E D

R

IV

E

U N

IT

D

E N

V E

R

C O

L O

R A

D O

-8

C L I E N T

City of Olathe, Kansas

P R O J E C T

D O C U M E N T I S S U E

S H E E T T I T L E

S H E E T N U M B E R

27 August 2025

Signage & Wayfinding Plan for Parks, Trails, and Unique Places:

Pilot Project (Frontier Park)

ABCDEFGHIJKLMNOPQRSTUVWXYZ

abcdefghijklmnopqrstuvwxyz 1234567890&?

LATO REGULAR – IDENTIFICATION SIGNAGE

ABCDEFGHIJKLMNOPQRSTUVWXYZ

abcdefghijklmnopqrstuvwxyz 1234567890&?

LATO BOLD – IDENTIFICATION SIGNAGE

ABCDEFGHIJKLMNOPQRSTUVWXYZ

abcdefghijklmnopqrstuvwxyz 1234567890&?

LATO BLACK – IDENTIFICATION & WAYFINDING SIGNAGE

Typography

• These drawings are intended to illustrate design final engineering and conditions of the project are the responsibility of the fabricator.� Shop drawings by the fabricator must be submitted for approval, prior to proceeding with fabrication.

• The quality of fit and finish on the final product must meet or exceed the requirements of these design intent documents. Any variations to design, materials, or fabrication methods must be approved by the Owner and Tangram.

• Colors shown are for reference only and are subject to the limitations of the printing process.

Refer to referenced color systems contained within these drawings for actual specifications.

• Scaled examples shown are for reference only, and do not necessarily reflect actual site conditions. Detailed site surveys are required prior to fabrication and installation.

• All locations shown are approximate. All final locations are to be determined during pre-installation site walk-thrus, prior to sign fabrication and must be approved by Owner.

• Messages shown in these drawings are for general reference only. Refer to message schedules for actual required messages.�

T A

N G

R A

M D

E S

IG

N

,L

S A

N T

A F

E D

R

IV

E

U N

IT

D

E N

V E

R

C O

L O

R A

D O

-8

C L I E N T

City of Olathe, Kansas

P R O J E C T

D O C U M E N T I S S U E

S H E E T T I T L E

S H E E T N U M B E R

27 August 2025

Signage & Wayfinding Plan for Parks, Trails, and Unique Places:

Pilot Project (Frontier Park)

ABCDEFGHIJKLMNOPQRSTUVWXYZ

abcdefghijklmnopqrstuvwxyz 1234567890&?

ABCDEFGHIJKLMNOPQRSTUVWXYZ

abcdefghijklmnopqrstuvwxyz 1234567890&?

CLEARVIEW ADA CONDENSED MEDIUM – WAYFINDING SIGNAGE

CLEARVIEW HWY 2-B – WAYFINDING SIGNAGE

P2: Matthews Paint (MP) Black Stallion MP33653, Satin Finish

P1: Matthews Paint (MP) Czech Flag Blue MP02306, Satin Finish

Faux Corten P3: Matthews Paint (MP) Verizon White MP27386, Satin Finish

Reflective Vinyl: 3M™ Scotchlite™ Reflective Graphic Film 680-10 (White)

Opaque Vinyl: 3M™ Scotchcal Electrocut Opaque Film 7725-10 (White)

Typography & Colors

• These drawings are intended to illustrate design final engineering and conditions of the project are the responsibility of the fabricator.� Shop drawings by the fabricator must be submitted for approval, prior to proceeding with fabrication.

• The quality of fit and finish on the final product must meet or exceed the requirements of these design intent documents. Any variations to design, materials, or fabrication methods must be approved by the Owner and Tangram.

• Colors shown are for reference only and are subject to the limitations of the printing process.

Refer to referenced color systems contained within these drawings for actual specifications.

• Scaled examples shown are for reference only, and do not necessarily reflect actual site conditions. Detailed site surveys are required prior to fabrication and installation.

• All locations shown are approximate. All final locations are to be determined during pre-installation site walk-thrus, prior to sign fabrication and must be approved by Owner.

• Messages shown in these drawings are for general reference only. Refer to message schedules for actual required messages.�

T A

N G

R A

M D

E S

IG

N

,L

S A

N T

A F

E D

R

IV

E

U N

IT

D

E N

V E

R

C O

L O

R A

D O

-8

C L I E N T

City of Olathe, Kansas

P R O J E C T

D O C U M E N T I S S U E

S H E E T T I T L E

S H E E T N U M B E R

27 August 2025

Signage & Wayfinding Plan for Parks, Trails, and Unique Places:

Pilot Project (Frontier Park)

Restroom Picnic Area Hiking

BaseballPlayground Soccer

Walking

Biking

SYMBOLS

These are the various symbols that will be used in the pilot project wayfinding signage system.

Graphic Elements

SIGN FAMILY

• These drawings are intended to illustrate design final engineering and conditions of the project are the responsibility of the fabricator.� Shop drawings by the fabricator must be submitted for approval, prior to proceeding with fabrication.

• The quality of fit and finish on the final product must meet or exceed the requirements of these design intent documents. Any variations to design, materials, or fabrication methods must be approved by the Owner and Tangram.

• Colors shown are for reference only and are subject to the limitations of the printing process.

Refer to referenced color systems contained within these drawings for actual specifications.

• Scaled examples shown are for reference only, and do not necessarily reflect actual site conditions. Detailed site surveys are required prior to fabrication and installation.

• All locations shown are approximate. All final locations are to be determined during pre-installation site walk-thrus, prior to sign fabrication and must be approved by Owner.

• Messages shown in these drawings are for general reference only. Refer to message schedules for actual required messages.�

T A

N G

R A

M D

E S

IG

N

,L

S A

N T

A F

E D

R

IV

E

U N

IT

D

E N

V E

R

C O

L O

R A

D O

-8

C L I E N T

City of Olathe, Kansas

P R O J E C T

D O C U M E N T I S S U E

S H E E T T I T L E

S H E E T N U M B E R

27 August 2025

Signage & Wayfinding Plan for Parks, Trails, and Unique Places:

Pilot Project (Frontier Park)

Sign Family

A.3A Freestanding Park Identification C.1 Freestanding Parking Identification D.1 Freestanding Directory

F.1 Freestanding Trail Identification F.2 Freestanding Trail Identification and Directional

G.1 Freestanding Mile Marker H.2 Wall/Fence Mounted Field Identification

H.3 Pole Mounted Shelter Identification

E.1 Freestanding Pedestrian Directional

Frontier Park 15501 Indian Creek Pkwy

P Parking

Frontier Park

Frontier Park

MILE

Indian Creek Trail

Indian Creek Trail

MILE

15.5

Baseball

Field Frontier Park

Indian Creek Library

Indian Creek Trail

Restroom 2.5 mi

2.5 mi

Bell Cultural Events Center 3 mi

Black Bob Park

Field 1

Fields 2,3,4,5

Soccer Fields 6,7,8,9

Batting Cages

Mill Creek

3 min

4 min

4 min

6 min

6 min

Shelter

DESIGN INTENTS

• These drawings are intended to illustrate design final engineering and conditions of the project are the responsibility of the fabricator.� Shop drawings by the fabricator must be submitted for approval, prior to proceeding with fabrication.

• The quality of fit and finish on the final product must meet or exceed the requirements of these design intent documents. Any variations to design, materials, or fabrication methods must be approved by the Owner and Tangram.

• Colors shown are for reference only and are subject to the limitations of the printing process.

Refer to referenced color systems contained within these drawings for actual specifications.

• Scaled examples shown are for reference only, and do not necessarily reflect actual site conditions. Detailed site surveys are required prior to fabrication and installation.

• All locations shown are approximate. All final locations are to be determined during pre-installation site walk-thrus, prior to sign fabrication and must be approved by Owner.

• Messages shown in these drawings are for general reference only. Refer to message schedules for actual required messages.�

T A

N G

R A

M D

E S

IG

N

,L

S A

N T

A F

E D

R

IV

E

U N

IT

D

E N

V E

R

C O

L O

R A

D O

-8

C L I E N T

City of Olathe, Kansas

P R O J E C T

D O C U M E N T I S S U E

S H E E T T I T L E

S H E E T N U M B E R

27 August 2025

Signage & Wayfinding Plan for Parks, Trails, and Unique Places:

Pilot Project (Frontier Park)

1 Plan View

SCALE: 1/2" = 1'

3 Side View 1

SCALE: 1/2" = 1'

2 Front Elevation

SCALE: 1/2" = 1'

4 Backside Elevation

SCALE: 1/2" = 1'

5 Inner Frame Elevation

SCALE: 1/2" = 1'

Frontier Park 15501 Indian Creek Pkwy

Frontier Park 15501 Indian Creek Pkwy 15501 Indian Creek Pkwy

Pg. 15

Frontier Park

Concrete Footer The size and depth of the concrete footer shall be determined by the fabricator. The footers must be certified by engineers registered in the state of Kansas.

9' 0"

8' 0"

9' 6"

Faux Corten Panel Placement

Blue Panel Placement

Inset Tube

Inset TubeRectangle Tube 4 x 6" aluminum rectangle tubes welded to the rectangle posts.

Paint P2.

2.125"

Rectangle Post 4 x 6" Rectangle aluminum post to be direct buried.

Paint P2.

Faux Corten Panel 1/4" Aluminum panel with faux corten finish.

The panel is mechanically attached to the rectangle posts and inner frame with countersunk screws.

Sign Panel 1/8" Breakform aluminum panels mechanically attached to the faux corten panel with countersunk screws. Paint P1.

Type and graphics to be 3M™ Scotchlite™ Reflective Graphic Film 680-10 (White)

Logo 1/4" Aluminum circular panels mechanically attached to the faux corten panel with hidden fasteners. Paint P1. Graphics to be 3M™ Scotchlite™ Reflective Graphic Film 680-10 (White). Final logo to be determined.

Park Symbols 1/4" Aluminum circular panels mechanically attached to the faux corten panel with hidden fasteners. Paint P1. Graphics to be 3M™ Scotchlite™ Reflective Graphic Film 680-10 (White). Final park symbols to be determined based on location/park.

4" 4.5" 1' 6"4.75"

6"

1' 10"

6"

2' 5"

3' 6"

4.75"

5' 2.75"

1' 8.75"

2' 4"

3' 1"

5' 5"5' 2.75"

6"

9' 6"

3" 9' 0" 3"

6" 8' 0" 6"

4"

2.125"

2' 10"

8' 6"

2" 2" 2"

C L 6" 8' 6" 6"

11" 6.5"

A.3A Freestanding Park Identification (Double-Sided)

• These drawings are intended to illustrate design final engineering and conditions of the project are the responsibility of the fabricator.� Shop drawings by the fabricator must be submitted for approval, prior to proceeding with fabrication.

• The quality of fit and finish on the final product must meet or exceed the requirements of these design intent documents. Any variations to design, materials, or fabrication methods must be approved by the Owner and Tangram.

• Colors shown are for reference only and are subject to the limitations of the printing process.

Refer to referenced color systems contained within these drawings for actual specifications.

• Scaled examples shown are for reference only, and do not necessarily reflect actual site conditions. Detailed site surveys are required prior to fabrication and installation.

• All locations shown are approximate. All final locations are to be determined during pre-installation site walk-thrus, prior to sign fabrication and must be approved by Owner.

• Messages shown in these drawings are for general reference only. Refer to message schedules for actual required messages.�

T A

N G

R A

M D

E S

IG

N

,L

S A

N T

A F

E D

R

IV

E

U N

IT

D

E N

V E

R

C O

L O

R A

D O

-8

C L I E N T

City of Olathe, Kansas

P R O J E C T

D O C U M E N T I S S U E

S H E E T T I T L E

S H E E T N U M B E R

27 August 2025

Signage & Wayfinding Plan for Parks, Trails, and Unique Places:

Pilot Project (Frontier Park)

1 Panel Attachment Details

SCALE: 3" = 1'

2 Sign Panel Details

SCALE: 1" = 1'

3 Faux Corten Panel Details

SCALE: 1" = 1'

Frontier Park 15501 Indian Creek Pkwy

0.25"

0.125"

0.25"

0.125"4.5"

4"

Rectangle Post 4 x 6" Rectangle aluminum post.

Paint P2.

Faux Corten Panel 1/4" Aluminum panel with faux corten finish. The panel is mechanically attached to the rectangle posts and inner frame with countersunk screws.

Sign Panel 1/8" Breakform aluminum panels mechanically attached to the faux corten panel with countersunk screws. Paint P1.

Type and graphics to be 3M™ Scotchlite™ Reflective Graphic Film 680-10 (White).

Inset Tube Aluminum square 2" x 2" tube inset 2" into the negative space between the breakform panels.

Inset tube mechanically attached to the inner frame. Paint P1.

0.125"

2"

4.75"

Font: Lato Black

Font: Lato Regular Countersunk screw locations

4.5"

2"

7.5"

6"

8"

1' 9"

9' 0"

3' 6"

6" 11"

3"

6.5" 2" 6.5" 2" 6.5" 2" 6.5" 2" 6.5" 2" 6.5" 6"

2" 6.75"

• These drawings are intended to illustrate design final engineering and conditions of the project are the responsibility of the fabricator.� Shop drawings by the fabricator must be submitted for approval, prior to proceeding with fabrication.

• The quality of fit and finish on the final product must meet or exceed the requirements of these design intent documents. Any variations to design, materials, or fabrication methods must be approved by the Owner and Tangram.

• Colors shown are for reference only and are subject to the limitations of the printing process.

Refer to referenced color systems contained within these drawings for actual specifications.

• Scaled examples shown are for reference only, and do not necessarily reflect actual site conditions. Detailed site surveys are required prior to fabrication and installation.

• All locations shown are approximate. All final locations are to be determined during pre-installation site walk-thrus, prior to sign fabrication and must be approved by Owner.

• Messages shown in these drawings are for general reference only. Refer to message schedules for actual required messages.�

T A

N G

R A

M D

E S

IG

N

,L

S A

N T

A F

E D

R

IV

E

U N

IT

D

E N

V E

R

C O

L O

R A

D O

-8

C L I E N T

City of Olathe, Kansas

P R O J E C T

D O C U M E N T I S S U E

S H E E T T I T L E

S H E E T N U M B E R

27 August 2025

Signage & Wayfinding Plan for Parks, Trails, and Unique Places:

Pilot Project (Frontier Park)

4 5

2 3

1 Sign Panel Assembly Detail- Double Sided

SCALE: NTS

4 x 6" Rectangle tubes are to be welded together to create the inner frame.

Circular aluminum panels mechanically attached to the faux corten panel.

Faux corten panels mechanically attached to the front and back of the inner frame.

Blue breakformed panels & inset tubes mechanically attached to the faux corten panels on the front and back of the structure.

• These drawings are intended to illustrate design final engineering and conditions of the project are the responsibility of the fabricator.� Shop drawings by the fabricator must be submitted for approval, prior to proceeding with fabrication.

• The quality of fit and finish on the final product must meet or exceed the requirements of these design intent documents. Any variations to design, materials, or fabrication methods must be approved by the Owner and Tangram.

• Colors shown are for reference only and are subject to the limitations of the printing process.

Refer to referenced color systems contained within these drawings for actual specifications.

• Scaled examples shown are for reference only, and do not necessarily reflect actual site conditions. Detailed site surveys are required prior to fabrication and installation.

• All locations shown are approximate. All final locations are to be determined during pre-installation site walk-thrus, prior to sign fabrication and must be approved by Owner.

• Messages shown in these drawings are for general reference only. Refer to message schedules for actual required messages.�

T A

N G

R A

M D

E S

IG

N

,L

S A

N T

A F

E D

R

IV

E

U N

IT

D

E N

V E

R

C O

L O

R A

D O

-8

C L I E N T

City of Olathe, Kansas

P R O J E C T

D O C U M E N T I S S U E

S H E E T T I T L E

S H E E T N U M B E R

27 August 2025

Signage & Wayfinding Plan for Parks, Trails, and Unique Places:

Pilot Project (Frontier Park)

1 Plan View

SCALE: 1/2" = 1'

3 Side View 1

SCALE: 1/2" = 1'

2 Front Elevation

SCALE: 1/2" = 1'

5 Inner Frame Elevation

SCALE: 1/2" = 1'

4 Backside Elevation

SCALE: 1/2" = 1'

Pg. 18

P Parking

Frontier Park

Inset Tube

Concrete Footer The size and depth of the concrete footer shall be determined by the fabricator. The footers must be certified by engineers registered in the state of Kansas.

1.625"

Corten Panel Placement

4"

9' 7"

5" 1' 9.5"

2' 2.5"

5"

9' 2"

1' 6"

Rectangle Post 3 x 5" Rectangle aluminum post.

Paint P2.

Sign Panel 1/8" Breakform aluminum panel mechanically attached to the faux corten panel with countersunk screws. Paint P1.

Type and graphics to be 3M™ Scotchlite™ Reflective Graphic Film 680-10 (White).

Faux Corten Panel 1/4" Aluminum panel with faux corten finish. The panel is mechanically attached to the rectangle posts and inner frame with countersunk screws. Backside of panel painted P1. Type to be 3M™ Scotchlite™ Reflective Graphic Film 680-10 (White).

Breakaway Base KDOT approved breakaway base.

See page 30 for more details.

Rectangle Tube 3 x 5" aluminum rectangle tube welded to the rectangle post.

Paint P2.

9' 8"

3' 0"

6' 8"

2" 1' 8" 2"

2.5" 2' 0"

2' 2.5"

3.5"

1.625"

9' 4"

3"

3.5"3"

9' 9.625"

2' 6"

6' 10.625"

4"

Inset Tube

Blue Panel Placement

1.5" 2" 2"

C.1 Freestanding Parking Identification

• These drawings are intended to illustrate design final engineering and conditions of the project are the responsibility of the fabricator.� Shop drawings by the fabricator must be submitted for approval, prior to proceeding with fabrication.

• The quality of fit and finish on the final product must meet or exceed the requirements of these design intent documents. Any variations to design, materials, or fabrication methods must be approved by the Owner and Tangram.

• Colors shown are for reference only and are subject to the limitations of the printing process.

Refer to referenced color systems contained within these drawings for actual specifications.

• Scaled examples shown are for reference only, and do not necessarily reflect actual site conditions. Detailed site surveys are required prior to fabrication and installation.

• All locations shown are approximate. All final locations are to be determined during pre-installation site walk-thrus, prior to sign fabrication and must be approved by Owner.

• Messages shown in these drawings are for general reference only. Refer to message schedules for actual required messages.�

T A

N G

R A

M D

E S

IG

N

,L

S A

N T

A F

E D

R

IV

E

U N

IT

D

E N

V E

R

C O

L O

R A

D O

-8

C L I E N T

City of Olathe, Kansas

P R O J E C T

D O C U M E N T I S S U E

S H E E T T I T L E

S H E E T N U M B E R

27 August 2025

Signage & Wayfinding Plan for Parks, Trails, and Unique Places:

Pilot Project (Frontier Park)

P Parking

Frontier Park

1 Panel Attachment Details

SCALE: 3" = 1'

2 Corten Panel Details

SCALE: 1 1/2" = 1'

3 Sign Panel Details

SCALE: 1 1/2" = 1'

0.125"

0.125" 0.25"

0.125"

Rectangle Post 3 x 5" Rectangle aluminum post.

Paint P2.

Faux Corten Panel 1/4" Aluminum panel with faux corten finish. The panel is mechanically attached to the rectangle posts and inner frame with countersunk screws. Backside of panel painted P1.

1.5"

2.5"

3"

3.25"

Font: Lato Black

Font: Lato Black

Font: Lato Bold

2"

3.1875"

1.25"

2'

3'

4"

3"

4.5"

1' 1.5"

5"

1' 8"

Countersunk screw locations

4.125"4"

3.5"

2' 6"

Sign Panel 1/8" Breakform aluminum panel mechanically attached to the faux corten panel with countersunk screws. Paint P1.

Type and graphics to be 3M™ Scotchlite™ Reflective Graphic Film 680-10 (White)

Inset Tube Aluminum rectangle 2" x 1.5" tube inset 2" into the negative space between the breakform panel. Inset tube mechanically attached to the inner frame.

Paint P1.

C.1 Freestanding Parking

• These drawings are intended to illustrate design final engineering and conditions of the project are the responsibility of the fabricator.� Shop drawings by the fabricator must be submitted for approval, prior to proceeding with fabrication.

• The quality of fit and finish on the final product must meet or exceed the requirements of these design intent documents. Any variations to design, materials, or fabrication methods must be approved by the Owner and Tangram.

• Colors shown are for reference only and are subject to the limitations of the printing process.

Refer to referenced color systems contained within these drawings for actual specifications.

• Scaled examples shown are for reference only, and do not necessarily reflect actual site conditions. Detailed site surveys are required prior to fabrication and installation.

• All locations shown are approximate. All final locations are to be determined during pre-installation site walk-thrus, prior to sign fabrication and must be approved by Owner.

• Messages shown in these drawings are for general reference only. Refer to message schedules for actual required messages.�

T A

N G

R A

M D

E S

IG

N

,L

S A

N T

A F

E D

R

IV

E

U N

IT

D

E N

V E

R

C O

L O

R A

D O

-8

C L I E N T

City of Olathe, Kansas

P R O J E C T

D O C U M E N T I S S U E

S H E E T T I T L E

S H E E T N U M B E R

27 August 2025

Signage & Wayfinding Plan for Parks, Trails, and Unique Places:

Pilot Project (Frontier Park)

3 Side View 1

SCALE: 3/4" = 1'

4 Backside Elevation- Single Sided

SCALE: 3/4" = 1'

1 Plan View

SCALE: 3/4" = 1'

2 Front Elevation

SCALE: 3/4" = 1'

Frontier Park

Pg. 20

Concrete Footer The size and depth of the concrete footer shall be determined by the fabricator. The footers must be certified by engineers registered in the state of Kansas.

1' 0"

4' 0"

4' 5"

2.5" 4' 5" 2.5"

6"

6"

5" Rectangle Post 3 x 5" Rectangle aluminum post to be direct buried.

Paint P2.

HPL Directory Panel 1/4” iZONE High Pressure Laminate (HPL) panel with 90 degree corners mechanically attached to the sign panel with countersunk screws.

Artwork for the map is to be provided by Olathe.

Sign Panel 1/8" Breakform aluminum panel mechanically attached to the faux corten panel with countersunk screws. Paint P1. Type and graphics to be 3M™ Scotchlite™ Reflective Graphic Film 680-10 (White).

Logo 1/4" Aluminum circular panels mechanically attached to the faux corten panel with hidden fastners. Paint P1. Graphics to be 3M™ Scotchlite™ Reflective Graphic Film 680-10 (White).

Final logo to be determined.

Faux Corten Panel 1/4" Aluminum panel with faux corten finish. The panel is mechanically attached to the rectangle posts and inner frame with countersunk screws.

Backside of panel painted P1.

Type and graphics to be 3M™ Scotchlite™ Reflective Graphic Film 680-10 (White).

6' 9" 6' 9"

5"

2.125"

4' 10"

3"

5"

3.5"

3"2.5" 4' 0" 2.5"

3' 7"

3' 4.25"

2.125"

4' 2"

2' 7"

6' 11.125"

3.5" Inset Tube

D.1 Freestanding Directory

• These drawings are intended to illustrate design final engineering and conditions of the project are the responsibility of the fabricator.� Shop drawings by the fabricator must be submitted for approval, prior to proceeding with fabrication.

• The quality of fit and finish on the final product must meet or exceed the requirements of these design intent documents. Any variations to design, materials, or fabrication methods must be approved by the Owner and Tangram.

• Colors shown are for reference only and are subject to the limitations of the printing process.

Refer to referenced color systems contained within these drawings for actual specifications.

• Scaled examples shown are for reference only, and do not necessarily reflect actual site conditions. Detailed site surveys are required prior to fabrication and installation.

• All locations shown are approximate. All final locations are to be determined during pre-installation site walk-thrus, prior to sign fabrication and must be approved by Owner.

• Messages shown in these drawings are for general reference only. Refer to message schedules for actual required messages.�

T A

N G

R A

M D

E S

IG

N

,L

S A

N T

A F

E D

R

IV

E

U N

IT

D

E N

V E

R

C O

L O

R A

D O

-8

C L I E N T

City of Olathe, Kansas

P R O J E C T

D O C U M E N T I S S U E

S H E E T T I T L E

S H E E T N U M B E R

27 August 2025

Signage & Wayfinding Plan for Parks, Trails, and Unique Places:

Pilot Project (Frontier Park)

1 Inner Frame Elevation

SCALE: 3/4" = 1'

Blue Panel Placement

C L

Frontier Park

Corten Panel Placement

Rectangle Tube 3 x 5" aluminum rectangle tube welded to the rectangle post. Paint P2.

3 Sign Panel Details

SCALE: 1" = 1'

4 Faux Corten Panel Details

SCALE: 1" = 1'

2 Panel Attachment Details

SCALE: 3" = 1'

0.125"

0.125"

0.125"

0.25"

Rectangle Post 3 x 5" Rectangle aluminum post to be direct buried.

Paint P2.

Sign Panel 1/8" Breakform aluminum panel mechanically attached to the faux corten panel with countersunk screws. Paint P1.

Type and graphics to be 3M™ Scotchlite™ Reflective Graphic Film 680-10 (White)

Faux Corten Panel 1/4" Aluminum panel with faux corten finish.

The panel is mechanically attached to the rectangle posts and inner frame with countersunk screws.

Backside of panel painted P1.

HPL Directory Panel 1/4” iZONE High Pressure Laminate (HPL) panel with 90 degree corners mechanically attached to the sign panel with countersunk screws.

Artwork for the map is to be provided by Olathe.

2"

2.625"

4.625"4.75"

3"

3.25"

Font: Lato Black

5" 4' 0" 5"

5"

2' 11.5"

5."

2' 11.5"

2"

2.5"

2" 0.75"

2' 4"

0.75"

7"

3.5"

3' 7"

4'

2.25"

6"

3" 6"

4' 2"

4' 5"

Countersunk screw locations

Inset Tube Aluminum square 2" x 2" tube inset 2" into the negative space between the breakform panel.

Inset tube mechanically attached to the inner frame. Paint P1.

2" 2" 2"

Inset Tube

3.625"

D.1 Freestanding Directory

• These drawings are intended to illustrate design final engineering and conditions of the project are the responsibility of the fabricator.� Shop drawings by the fabricator must be submitted for approval, prior to proceeding with fabrication.

• The quality of fit and finish on the final product must meet or exceed the requirements of these design intent documents. Any variations to design, materials, or fabrication methods must be approved by the Owner and Tangram.

• Colors shown are for reference only and are subject to the limitations of the printing process.

Refer to referenced color systems contained within these drawings for actual specifications.

• Scaled examples shown are for reference only, and do not necessarily reflect actual site conditions. Detailed site surveys are required prior to fabrication and installation.

• All locations shown are approximate. All final locations are to be determined during pre-installation site walk-thrus, prior to sign fabrication and must be approved by Owner.

• Messages shown in these drawings are for general reference only. Refer to message schedules for actual required messages.�

T A

N G

R A

M D

E S

IG

N

,L

S A

N T

A F

E D

R

IV

E

U N

IT

D

E N

V E

R

C O

L O

R A

D O

-8

C L I E N T

City of Olathe, Kansas

P R O J E C T

D O C U M E N T I S S U E

S H E E T T I T L E

S H E E T N U M B E R

27 August 2025

Signage & Wayfinding Plan for Parks, Trails, and Unique Places:

Pilot Project (Frontier Park)

1 Plan View

SCALE: 1/2" = 1'

3 Side View 1

SCALE: 1/2" = 1'

2 Front Elevation

SCALE: 1/2" = 1'

5 Inner Frame Elevation

SCALE: 1/2" = 1'

4 Backside Elevation

SCALE: 1/2" = 1'

Black Bob Park

Field 1

Fields 2,3,4,5

Soccer Fields 6,7,8,9

Batting Cages

Mill Creek

3 min

4 min

4 min

6 min

6 min

Corten Panel Placement

Rectangle Tube 3 x 6" aluminum rectangle tube welded to the rectangle post.

Paint P2.

Concrete Footer The final size and depth of the concrete footer shall be determined by the fabricator.

1.875"1.875"

Pg. 22

10' 3"

4"

Sign Panel 1/8" Breakform aluminum panel mechanically attached to the faux corten panel with countersunk screws. Paint P1. Type and graphics to be 3M™ Scotchlite™ Reflective Graphic Film 680-10 (White).

Breakaway Base KDOT approved breakaway base.

See page 30 for more details.

10' 3"

2' 6"

9' 11"

6" 2' 7.125"

3' 1.5"

3' 1"

3" 2' 10"

Faux Corten Panel 1/4" Aluminum panel with faux corten finish. The panel is mechanically attached to the rectangle posts and inner frame with countersunk screws. Backside of panel painted P1. Type to be 3M™ Scotchlite™ Reflective Graphic Film 680-10 (White).

6"

9' 9"

3.5"

Rectangle Post 3 x 6" Rectangle aluminum post to be direct buried.

Paint P2.

3" 1' 6"3.5"

3"

2.625"

3' 2.875"

6' 10.75"

4"

2.625"

3' 7"

6' 8" (If located over a pedestrian pathway change to 7')

10' 5.625"

Inset Tube

Blue Panel Placement

Inset Tube

E.1 Freestanding Pedestrian Directional

• These drawings are intended to illustrate design final engineering and conditions of the project are the responsibility of the fabricator.� Shop drawings by the fabricator must be submitted for approval, prior to proceeding with fabrication.

• The quality of fit and finish on the final product must meet or exceed the requirements of these design intent documents.