141 60 10 Vibrating Oscilating Roller.docx

Specification No. 141-60-10

Specification No. 141-60-10

Specifications for a Self-Propelled, Vibrating and Oscillating Type Tandem Roller

State of Illinois Department of Transportation Bureau of Business Services Specifications for a Self-Propelled, Vibrating and Oscillating Type Tandem Roller April 2020 This specification and questionnaire covers a self-propelled Vibrating and Oscillating Type Tandem Roller for use in Department of Transportation highway maintenance operations. The Department of Transportation is specifying acceptable units by required features and accessories as outlined below.

Each bidder shall submit with their bid two sets of descriptive literature and specifications describing all the equipment and options proposed. This information shall be clearly marked to indicate the make, model, and accessories proposed to be furnished.

Bidders quoting on other-than-specified equipment must submit with their bid written proof of the following:

· The manufacturer of the equipment proposed has been actively involved in the manufacture of the equipment called for in the Proposal for a period of not less than 5 years.

· Parts and service for the equipment proposed are readily available to the State of Illinois.

It is the responsibility of each bidder to complete and return this questionnaire with the bid.

Unless otherwise specified, the proposed equipment shall be complete in all parts and ready for immediate use upon delivery.

Bidders are advised to carefully read these specifications as changes have been made since the last solicitation issue.

Proposed with this Bid:

The Illinois Department of Transportation reserves the right to waive minor informalities, deficiencies or technical variances which by their nature are restrictive to a given manufacturer, if in its’ judgement, it would be in the best interest of the State to do so and it would not prejudice the rights of other bidders.

Serviceability will be a factor in award. Successful bidder shall either be able to provide service after purchase or shall indicate other qualified service facilities able to service equipment, within a reasonable period of time at agency locations. Bidder shall provide documentation and enumerating service locations. A Review of the bidder's ability to provide prompt parts and service to the State of Illinois and in particular to the delivery location, will be considered in determining award.

Bids will only be accepted from established manufacturers or their authorized dealers. Any dealer submitting a bid hereby guarantees that it is an authorized dealer of the manufacturer and that the manufacturer has agreed to supply the dealer with all quantities of products required by the dealer in fulfillment of its obligations under any resultant contract with the State. Bidder must submit authorized dealer letter upon request.

Warranty:

Unless otherwise specified, Manufacturers’ standard warranty shall be provided. Bidder shall attach copies of warranty with their bid. Warranty shall commence at the Illinois Department of Transportation in-service date. If any equipment fails to conform to the warranties during the applicable warranty period, the Vendor or Manufacturer will adjust, repair or replace the equipment at no charge to the Department as soon as possible upon notice from the Department. Equipment shall be repaired on-site and will be performed at no additional cost to the Department.

The Vendor may provide or perform warranty service at a dealer location within the Districts geographic region if on-site repair is not possible. Vendor shall facilitate pickup and delivery of equipment at Vendor's cost if warranty repair(s) are made off-site during the warranty period. The contract Vendor is responsible for any failure of their allied or sub-contractors’ fulfillment of said warranties. Failure to provide this service shall result in a “Complaint to Vendor” that could affect future bid awards.

Delivery:

It will be the responsibility of the successful vendor to guarantee delivery within the quoted time and to require allied manufacturers or suppliers to complete the installation of auxiliary equipment in accordance with the quoted delivery time.

Failure to comply with the quoted delivery time because of delays resulting from the inability of suppliers of allied equipment such as bodies, snowplows, spreaders, etc., may be reason to refuse to consider similar items from those suppliers on future bids.

All equipment provided by the Vendor and the sub-contractor(s) shall be fully operational when delivery is made. Any noted defects at the time of delivery shall be addressed by Vendor in the first 30 days of in-service.

Bidder/Vendor acknowledges the requirements above. Yes |_| No |_|

Note: If the equipment proposed exceeds the minimums called for in the specification please do not mark NO. Mark Yes and explain with a short comment on how it exceeds.

The unit shall include the following standard or optional accessories and equipment:

Vibration/Oscillation system:

Tandem style dual drum roller with hydrostatic drive. The unit shall be capable of both vibration and oscillation type compaction. The vibration and oscillation functions shall be manually or automatically switched separately. The vibration and oscillation frequencies shall be displayed and adjustable from the operator’s station. This type of system is a key factor in the scope of work this unit will perform.

Complies: |_| Yes |_| No Please describe system:

Weight and Dimensions:

The unit shall have a maximum loaded weight of 27,000 lbs. and a minimum operating weight of 19,000 lbs.

Minimum overall width shall be 70”.

Minimum total overall length of unit shall be 180”.

Drums:

Front and rear drums shall be steel with machine finished, chamfered edges and include full width scrapers. If available, the drum edges shall be lighted for low light operations.

Complies: |_| Yes |_| No Front /Rear drums shall be a minimum of 47" in diameter and a minimum 66" in width.

Water Spray System:

Water spray system with front and rear tanks, minimum capacity of 200 gal.

The water tank and spray bars shall be non-corroding. The water spray system shall include a filtration system that is field serviceable to reduce downtime of the machine. The unit shall be equipped with industry standard moisture mat belting to evenly disperse the sprayed water on the drums. The tanks shall include left and right filler caps and a centralized drain system to allow complete draining of system for storage.

The water system shall provide operator controlled or preselected option for pressurized water to the fan spray nozzles. The water flow control shall be provided and controlled from the operator’s control station. A water level indicator shall be provided.

Complies: |_| Yes |_| No The nozzles shall be visible and field serviceable by hand to help with cleaning or maintenance. Special tools shall not be needed to change the nozzles.

Engine:

The roller shall be provided with a current production liquid cooled diesel engine meeting the following:

· Minimum 110 HP

· Dry style air cleaner

· Fuel filter water separator

· 12-volt electrical system

· Alternator/regulator

· Maintenance free battery

· Tier 4F Emissions

Component provided:

The unit shall have a minimum 40-gallon fuel tank capacity.

Complies: |_| Yes |_| No Drivetrain:

The drivetrain shall be fully hydrostatic, with infinite variable control of both direction and speed.

Complies: |_| Yes |_| No The drum drive motors shall be low speed high torque type with low and high-speed capability.

Complies: |_| Yes |_| No The speed shall be infinitely variable with a travel speed of approximately 7 mph and approximate working speed of 4 mph.

The unit shall be equipped with a parking brake and emergency stop switch located in the operator’s station.

Complies: |_| Yes |_| No

Operator’s Station:

The operator’s station shall have a safe, comfortable, rotating seat with a minimum of 150-degree rotation. The seat shall include a safety lap belt. The operator’s station shall allow the operator to face forward or sideways to have full view of both drums. Rear view mirrors shall be included.

The operator shall have unobstructed view of the drums and their edges.

Complies: |_| Yes |_| No

The propulsion lever, steering wheel, parking and secondary brake, and horn shall be within convenient reach of the operator from either position.

Complies: |_| Yes |_| No

The following gauges or indicators shall be provided in the operator’s station:

Hour meter Voltmeter Fuel level Engine oil pressure Engine coolant temperature Engine air filter restriction Hydraulic oil filter restriction Water level Asphalt temperature gauge

A neutral start safety switch is required.

Complies: |_| Yes |_| No The operator’s platform area shall include a roll over protection system (ROPS) and falling objects protection system (FOPS). The operator’s platform shall include safety railings, skid resistant surfaces and hand holds for entering and exiting the operator’s station.

Complies: |_| Yes |_| No Steering:

Control provided by an automotive style steering component.

Complies: |_| Yes |_| No Steering shall be full hydrostatic power with an inside turning radius of approximately 220”.

The steering angle shall be +/- 30 and oscillation +/- 10.

Complies: |_| Yes |_| No Electrical:

The unit shall be equipped with a main battery disconnect that will disable entire electrical system.

Complies: |_| Yes |_| No |_| Not Available Lighting: The unit shall be equipped with LED Amber warning beacon, turn signals, flashers, and drum lighting. High intensity work/driving lights shall be included for nighttime or low light paving operations. All lighting shall be controlled from the operator’s station.

Back up alarm: The unit shall include a weatherproof back up alarm. Noise levels should not exceed open cab OHSA standards in the operator’s station.

Complies: |_| Yes |_| No Finish:

All exterior surfaces normally powder coated or painted shall be the manufacturer’s standard color.

Warranty:

Full coverage warranty for a minimum 12 months shall be provided. The warranty shall be the standard maximum coverage warranty offered with no additional charges. The bidder shall attach a copy of warranty with the bid.

Preparation:

This machine is to be delivered in first-class operating condition with acceptance subject to Department of Transportation approval.

Complies: Yes |_| No |_| The unit shall be delivered oiled, greased, serviced and ready for operation.

Complies: Yes |_| No |_| General:

Three copies of all operator’s manuals, parts lists, and warranty information shall be provided at time of delivery to each district receiving one or more units.

Complies: Yes |_| No |_| One set of service manuals shall be provided to each delivery location.

Complies: Yes |_| No |_| Note: The manuals, parts lists, and service or shop manuals listed above may be furnished on CD/DVD or flash drive in lieu of paper.

Training:

Instruction shall be performed by qualified factory or dealer personnel covering the operation, routine service and maintenance of the machine shall be provided upon delivery. The training shall be for all personnel in the assigned headquarters location of the machine. More than a single day may be required to satisfy this requirement.

Complies: Yes |_| No |_|

Note: This is not a sales call. Training not meeting IDOT expectations will generate a “Complaint-to-Vendor” that would affect award recommendations for future quotations.

Requirements Covering Items Detailed Above:

All equipment cataloged as standard or safety related shall be furnished and in place and shall be included in the purchase price of the unit. Any parts, tools, and/or accessories not specifically called for but required for proper operation shall be provided.

Complies: |_| Yes |_| No The component parts of the unit shall be of proper size and design to safely withstand maximum stresses imposed by a capacity load, and the manufacturer's rated loads for all component parts shall not be exceeded when the unit is so loaded.

Complies: |_| Yes |_| No Repair Parts and Service:

Since continuous operation of this excavator is of the utmost importance and sometimes of an emergency nature, it is necessary that the successful bidder be in a position to render prompt parts and service within the State of Illinois.

The vendor or manufacturer of the unit which is considered for award shall, at the request of the State of Illinois, demonstrate this equipment within the receiving District in the State of Illinois in the presence of authorized State personnel to prove out any features which may be in question.

Complies: Yes |_| No |_| Bid Package:

If not quoting in BidBuy, bidders will need to send two copies of each of the following with their bid response.

a) Specification Questionnaire

b) Descriptive Literature Picture is for visual reference only.

image1.png