Revised_Attachment_3_Description_of_Work_and_Drawings_4.15.19Rev1.pdf

AutoCAD SHX Text GENERAL NOTES: 1. FOR THIS PROJECT STANDARD SPECIFICATIONS FOR CONSTRUCTION OF ROADS AND BRIDGES ON FEDERAL HIGHWAY FOR THIS PROJECT STANDARD SPECIFICATIONS FOR CONSTRUCTION OF ROADS AND BRIDGES ON FEDERAL HIGHWAY PROJECTS AND SPECIAL PROJECT SPECIFICATIONS WILL BE USED, HEREINAFTER REFERRED TO AS FP-14. 2. STORAGE OF ALL EQUIPMENT ON SITE WILL BE AT THE PURCHASER'S RISK AND AT A LOCATION STORAGE OF ALL EQUIPMENT ON SITE WILL BE AT THE PURCHASER'S RISK AND AT A LOCATION APPROVED BY THE COR. 3. CONSTRUCTION EQUIPMENT SHALL BE CONFINED TO THE ROADWAY, UNLESS OTHERWISE APPROVED BY THE COR. CONSTRUCTION EQUIPMENT SHALL BE CONFINED TO THE ROADWAY, UNLESS OTHERWISE APPROVED BY THE COR. 4. ALL EXCAVATION IS CONSIDERED TO BE UNCLASSIFIED REGARDLESS OF MATERIAL TYPE ENCOUNTERED. ALL EXCAVATION IS CONSIDERED TO BE UNCLASSIFIED REGARDLESS OF MATERIAL TYPE ENCOUNTERED. 5. CONTRACTOR SHALL BE RESPONSIBLE FOR DAMAGE AND EXCESSIVE WEAR OF NATIONAL FOREST ROADS DUE TO CONTRACTOR SHALL BE RESPONSIBLE FOR DAMAGE AND EXCESSIVE WEAR OF NATIONAL FOREST ROADS DUE TO TRANSPORTATION OF CONTRACT EQUIPMENT AND OR MATERIALS. 6. CONTRACTOR SHALL BE RESPONSIBLE FOR THE DIVERSION OF WATER DURING ALL CULVERT INSTALLATIONS WHERE WATER CONTRACTOR SHALL BE RESPONSIBLE FOR THE DIVERSION OF WATER DURING ALL CULVERT INSTALLATIONS WHERE WATER IS PRESENT. 7. EACH CULVERT'S LOCATION AND LENGTH SHALL BE FIELD VERIFIED BY THE CONTRACTOR AND APPROVED BY THE COR EACH CULVERT'S LOCATION AND LENGTH SHALL BE FIELD VERIFIED BY THE CONTRACTOR AND APPROVED BY THE COR PRIOR TO ORDERING. 8. WOODY MATERIAL CUT DURING CULVERT INSTALLATION SHALL BE WINDROWED ALONG FILL SLOPE EXCEPT IN SPECIFIED WOODY MATERIAL CUT DURING CULVERT INSTALLATION SHALL BE WINDROWED ALONG FILL SLOPE EXCEPT IN SPECIFIED AREAS. 9. EXISTING CULVERTS TO BE REMOVED ARE THE PROPERTY OF THE CONTRACTOR AND SHALL BE REMOVED FROM NATIONAL EXISTING CULVERTS TO BE REMOVED ARE THE PROPERTY OF THE CONTRACTOR AND SHALL BE REMOVED FROM NATIONAL FOREST LANDS AND DISPOSED OF PROPERLY. 10. FILL SLOPE= 1V:1H, CUT SLOPE=1.3V:1H, OR AS STAKED BY THE COR. FILL SLOPE= 1V:1H, CUT SLOPE=1.3V:1H, OR AS STAKED BY THE COR. 11. WOODY MATERIAL GREATER THAN 2" IN DIAMETER OR LONGER THAN 3' SHALL NOT BE INCORPORATED INTO CONSTRUCTED WOODY MATERIAL GREATER THAN 2" IN DIAMETER OR LONGER THAN 3' SHALL NOT BE INCORPORATED INTO CONSTRUCTED FILLS. 12. DEPTHS OF MATERIALS TO BE COMPACTED ARE GIVEN AS FINAL COMPACTED DEPTHS. DEPTHS OF MATERIALS TO BE COMPACTED ARE GIVEN AS FINAL COMPACTED DEPTHS. 13. THE CONTRACTOR IS RESPONSIBLE FOR ALL TRAFFIC CONTROL INCLUDING TEMPORARY SIGNING AND PROTECTION OF THE THE CONTRACTOR IS RESPONSIBLE FOR ALL TRAFFIC CONTROL INCLUDING TEMPORARY SIGNING AND PROTECTION OF THE PUBLIC. SIGNAGE BEYOND THOSE SHOWN ON THE DRAWINGS MAY BE REQUIRED. 14. TRAFFIC CONTROL SIGNS SHALL CONFORM TO MUTCD SPECIFICATIONS. TRAFFIC CONTROL SIGNS SHALL CONFORM TO MUTCD SPECIFICATIONS. 15. ALL DRAINAGE FEATURES ON PORTIONS OF ROADWAY TO RECEIVE WORK SHALL DRAIN. ALL DRAINAGE FEATURES ON PORTIONS OF ROADWAY TO RECEIVE WORK SHALL DRAIN. 16. ALL RIPRAP SHALL BE MACHINE PLACED, NOT SIDECAST OR END DUMPED.

AutoCAD SHX Text GENERAL NOTES: PAY ITEMS 1. CONTRACTOR IS RESPONSIBLE FOR PROTECTION OF ALL SURVEY STAKES AND MONUMENTS, QUALITY CONTROL, AND SAMPLING AND TESTING. CONTRACTOR IS RESPONSIBLE FOR PROTECTION OF ALL SURVEY STAKES AND MONUMENTS, QUALITY CONTROL, AND SAMPLING AND TESTING. NO SEPARATE PAYMENT WILL BE MADE. 2. CLEARING REQUIRED FOR CONSTRUCTION, RECONSTRUCTION, MAINTENANCE, INSTALLATION OF OUTLET DITCHES, CULVERT INSTALLATIONS, RIPRAP CLEARING REQUIRED FOR CONSTRUCTION, RECONSTRUCTION, MAINTENANCE, INSTALLATION OF OUTLET DITCHES, CULVERT INSTALLATIONS, RIPRAP PLACEMENT, IS INCIDENTAL TO THAT WORK REQUIREMENT AND NO SEPARATE PAYMENT WILL BE MADE. 20101 WASTE MATERIAL FROM CLEARING AND GRUBBING SHALL BE DISPOSED OF BY WINDROWING ALONG FILL SLOPE WHERE POSSIBLE. WASTE MATERIAL FROM CLEARING AND GRUBBING SHALL BE DISPOSED OF BY WINDROWING ALONG FILL SLOPE WHERE POSSIBLE. CLEARED MATERIAL SHALL BE SCATTERED WHERE WINDROWING NOT POSSIBLE. 20401 ANY EXCESS MATERIAL FROM EXCAVATION SHALL BE WASTED IN AN AREA APPROVED BY THE COR. ANY EXCESS MATERIAL FROM EXCAVATION SHALL BE WASTED IN AN AREA APPROVED BY THE COR. 20419 DITCH CONSTRUCTION INCLUDES ROADSIDE AND LEADOFF DITCH CONSTRUCTION. TYPE OF DITCH TO BE CONSTRUCTED IS SPECIFIED IN DITCH CONSTRUCTION INCLUDES ROADSIDE AND LEADOFF DITCH CONSTRUCTION. TYPE OF DITCH TO BE CONSTRUCTED IS SPECIFIED IN THE DESCRIPTIONS OF WORK. 30307 IN ADDITION TO THE WORK DESCRIBED IN THE SPECIFICATION, THIS ITEM ALSO INCLUDES CLEANING ALL DITCHES, RECONDITIONING CATCH IN ADDITION TO THE WORK DESCRIBED IN THE SPECIFICATION, THIS ITEM ALSO INCLUDES CLEANING ALL DITCHES, RECONDITIONING CATCH BASINS, OUTLET DITCHES, LEADOFF DITCHES, AND CULVERT INLETS. ALL WORK SHALL BE IN ACCORDANCE WITH THE TYPICAL SECTIONS AND DRAWINGS. RECONDITIONING OF ROAD OR DITCH LINES SHALL NOT UNDERCUT BACKSLOPE. WHERE UNDERCUT CUT SLOPES ARE PRESENT, THE BACKSLOPE (CUT-SLOPE) SHALL BE RESHAPED AND SEEDED. 60201 CLEARING AND SLOPE ROUNDING REQUIRED FOR CULVERT INSTALLATION IS INCIDENTAL TO CULVERT INSTALLATION. CONSTRUCTION OF CLEARING AND SLOPE ROUNDING REQUIRED FOR CULVERT INSTALLATION IS INCIDENTAL TO CULVERT INSTALLATION. CONSTRUCTION OF OUTLET DITCHES ARE INCIDENTAL TO CULVERT INSTALLATION AND NO SEPARATE PAYMENT WILL BE MADE. IN SIDEHILL SECTIONS, THE CONTRACTOR SHALL CONSTRUCT THE CULVERT CATCH BASIN AS SHOWN IN THE CATCH BASIN DETAILS ON IN SIDEHILL SECTIONS, THE CONTRACTOR SHALL CONSTRUCT THE CULVERT CATCH BASIN AS SHOWN IN THE CATCH BASIN DETAILS ON SHEET 26 AND RECONDITION 50' OF EXISTING DITCH LINE ON BOTH SIDES OF THE INSTALLATION. THIS WORK WILL BE INCIDENTAL TO THIS ITEM.

AutoCAD SHX Text SEEDING NOTES: 1. SEED ALL DISTURBED AREAS, INCLUDING THE ROAD. NO DISTURBED AREAS WILL BE LEFT WITHOUT SEED ALL DISTURBED AREAS, INCLUDING THE ROAD. NO DISTURBED AREAS WILL BE LEFT WITHOUT SEEDING FOR MORE THAN 15 DAYS AND IN NO CASE MORE THAN 14 DAYS AFTER WORK HAS CEASED. 2. SEEDING MIXTURES SHALL BE AS FOLLOWS: SEEDING MIXTURES SHALL BE AS FOLLOWS: APRIL 1 - SEPTEMBER 30 CREEPING RED FESCUE 30 LBS PER ACRE 30 LBS PER ACRE MILLET 30 LBS PER ACRE 30 LBS PER ACRE RYE 30 LBS PER ACRE 30 LBS PER ACRE 3. FERTILIZER SHALL BE 17-17-17 APPLIED AT 500 LBS. PER ACRE FERTILIZER SHALL BE 17-17-17 APPLIED AT 500 LBS. PER ACRE 4. AGRICULTURAL LIME SHALL BE APPLIED AT 2,000 LBS. PER ACRE AGRICULTURAL LIME SHALL BE APPLIED AT 2,000 LBS. PER ACRE 5. MULCH SHALL BE APPLIED AT 2,000 LBS. PER ACRE MULCH SHALL BE APPLIED AT 2,000 LBS. PER ACRE 6. DISTURBED OR NEWLY CONSTUCTED SLOPES WITHIN 25' OF STREAM COURSE SHALL BE DISTURBED OR NEWLY CONSTUCTED SLOPES WITHIN 25' OF STREAM COURSE SHALL BE IMMEDIATELY PROTECTED BY SEEDING WITH 10 LBS. PER AC. ANNUAL RYEGRASS AND 10 LBS. PER AC. TALL FESCUE AND COVERING WITH STRAW MULCH AND SMALL LIMBS. THIS ADDITIONAL SEEDING SHALL BE DONE THE SAME DAY AS THE DISTURBANCE (WHETHER COMPLETED OR NOT)

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

U.S. DEPARTMENT OF AGRICULTURE FOREST SERVICE REGION 8

AutoCAD SHX Text

GENERAL NOTES

NATIONAL FORESTS IN NORTH CAROLINA PISGAH NATIONAL FOREST PISGAH RANGER DISTRICT PISGAH ROAD WORK 2019

AutoCAD SHX Text

AutoCAD SHX Text

U.S. DEPARTMENT OF AGRICULTURE FOREST SERVICE REGION 8

AutoCAD SHX Text

NFSR 297, TURKEY PEN ROAD DESCRIPTION OF WORK

NATIONAL FORESTS IN NORTH CAROLINA PISGAH NATIONAL FOREST PISGAH RANGER DISTRICT PISGAH ROAD WORK 2019

AutoCAD SHX Text

AutoCAD SHX Text

U.S. DEPARTMENT OF AGRICULTURE FOREST SERVICE REGION 8

AutoCAD SHX Text

NFSR 297, TURKEY PEN ROAD DESCRIPTION OF WORK

NATIONAL FORESTS IN NORTH CAROLINA PISGAH NATIONAL FOREST PISGAH RANGER DISTRICT PISGAH ROAD WORK 2019

AutoCAD SHX Text

AutoCAD SHX Text

U.S. DEPARTMENT OF AGRICULTURE FOREST SERVICE REGION 8

AutoCAD SHX Text

NFSR 475B, HEADWATER ROAD DESCRIPTION OF WORK

NATIONAL FORESTS IN NORTH CAROLINA PISGAH NATIONAL FOREST PISGAH RANGER DISTRICT PISGAH ROAD WORK 2019

AutoCAD SHX Text

AutoCAD SHX Text

U.S. DEPARTMENT OF AGRICULTURE FOREST SERVICE REGION 8

AutoCAD SHX Text

NFSR 475B, HEADWATER ROAD DESCRIPTION OF WORK

NATIONAL FORESTS IN NORTH CAROLINA PISGAH NATIONAL FOREST PISGAH RANGER DISTRICT PISGAH ROAD WORK 2019

AutoCAD SHX Text

AutoCAD SHX Text

U.S. DEPARTMENT OF AGRICULTURE FOREST SERVICE REGION 8

AutoCAD SHX Text

NFSR 477, AVERY CREEK ROAD DESCRIPTION OF WORK

NATIONAL FORESTS IN NORTH CAROLINA PISGAH NATIONAL FOREST PISGAH RANGER DISTRICT PISGAH ROAD WORK 2019

AutoCAD SHX Text

AutoCAD SHX Text

U.S. DEPARTMENT OF AGRICULTURE FOREST SERVICE REGION 8

AutoCAD SHX Text

NFSR 477, AVERY CREEK ROAD DESCRIPTION OF WORK

NATIONAL FORESTS IN NORTH CAROLINA PISGAH NATIONAL FOREST PISGAH RANGER DISTRICT PISGAH ROAD WORK 2019

AutoCAD SHX Text

AutoCAD SHX Text

U.S. DEPARTMENT OF AGRICULTURE FOREST SERVICE REGION 8

AutoCAD SHX Text

NFSR 479, BENT CREEK ROAD DESCRIPTION OF WORK

NATIONAL FORESTS IN NORTH CAROLINA PISGAH NATIONAL FOREST PISGAH RANGER DISTRICT PISGAH ROAD WORK 2019

AutoCAD SHX Text

AutoCAD SHX Text

U.S. DEPARTMENT OF AGRICULTURE FOREST SERVICE REGION 8

AutoCAD SHX Text

NFSR 479, BENT CREEK ROAD DESCRIPTION OF WORK

NATIONAL FORESTS IN NORTH CAROLINA PISGAH NATIONAL FOREST PISGAH RANGER DISTRICT PISGAH ROAD WORK 2019

AutoCAD SHX Text

AutoCAD SHX Text

U.S. DEPARTMENT OF AGRICULTURE FOREST SERVICE REGION 8

AutoCAD SHX Text

NFSR 5000, WASH CREEK ROAD DESCRIPTION OF WORK

NATIONAL FORESTS IN NORTH CAROLINA PISGAH NATIONAL FOREST PISGAH RANGER DISTRICT PISGAH ROAD WORK 2019

AutoCAD SHX Text

AutoCAD SHX Text

U.S. DEPARTMENT OF AGRICULTURE FOREST SERVICE REGION 8

AutoCAD SHX Text

NFSR 5000, WASH CREEK ROAD DESCRIPTION OF WORK

NATIONAL FORESTS IN NORTH CAROLINA PISGAH NATIONAL FOREST PISGAH RANGER DISTRICT PISGAH ROAD WORK 2019

AutoCAD SHX Text

AutoCAD SHX Text

U.S. DEPARTMENT OF AGRICULTURE FOREST SERVICE REGION 8

AutoCAD SHX Text

NFSR 142, HENDERSONVILLE RESERVOIR ROAD DESCRIPTION OF WORK

NATIONAL FORESTS IN NORTH CAROLINA PISGAH NATIONAL FOREST PISGAH RANGER DISTRICT PISGAH ROAD WORK 2019

AutoCAD SHX Text

AutoCAD SHX Text

U.S. DEPARTMENT OF AGRICULTURE FOREST SERVICE REGION 8

AutoCAD SHX Text

NFSR 142, HENDERSONVILLE RESERVOIR ROAD DESCRIPTION OF WORK

NATIONAL FORESTS IN NORTH CAROLINA PISGAH NATIONAL FOREST PISGAH RANGER DISTRICT PISGAH ROAD WORK 2019

AutoCAD SHX Text

AutoCAD SHX Text

U.S. DEPARTMENT OF AGRICULTURE FOREST SERVICE REGION 8

AutoCAD SHX Text

NFSR 471, CATHEY'S CREEK ROAD DESCRIPTION OF WORK

NATIONAL FORESTS IN NORTH CAROLINA PISGAH NATIONAL FOREST PISGAH RANGER DISTRICT PISGAH ROAD WORK 2019

AutoCAD SHX Text

AutoCAD SHX Text

U.S. DEPARTMENT OF AGRICULTURE FOREST SERVICE REGION 8

AutoCAD SHX Text

NFSR 471, CATHEY'S CREEK ROAD DESCRIPTION OF WORK

NATIONAL FORESTS IN NORTH CAROLINA PISGAH NATIONAL FOREST PISGAH RANGER DISTRICT PISGAH ROAD WORK 2019

AutoCAD SHX Text

AutoCAD SHX Text

U.S. DEPARTMENT OF AGRICULTURE FOREST SERVICE REGION 8

AutoCAD SHX Text

NFSR 471, CATHEY'S CREEK ROAD DESCRIPTION OF WORK

NATIONAL FORESTS IN NORTH CAROLINA PISGAH NATIONAL FOREST PISGAH RANGER DISTRICT PISGAH ROAD WORK 2019

AutoCAD SHX Text

AutoCAD SHX Text

U.S. DEPARTMENT OF AGRICULTURE FOREST SERVICE REGION 8

AutoCAD SHX Text

NFSR 475, DAVIDSON RIVER ROAD DESCRIPTION OF WORK

NATIONAL FORESTS IN NORTH CAROLINA PISGAH NATIONAL FOREST PISGAH RANGER DISTRICT PISGAH ROAD WORK 2019

AutoCAD SHX Text

AutoCAD SHX Text

U.S. DEPARTMENT OF AGRICULTURE FOREST SERVICE REGION 8

AutoCAD SHX Text

NFSR 450, FRYING PAN ROAD DESCRIPTION OF WORK

NATIONAL FORESTS IN NORTH CAROLINA PISGAH NATIONAL FOREST PISGAH RANGER DISTRICT PISGAH ROAD WORK 2019

AutoCAD SHX Text

AutoCAD SHX Text

U.S. DEPARTMENT OF AGRICULTURE FOREST SERVICE REGION 8

AutoCAD SHX Text

NFSR 809, LOWER COVE CREEK ROAD DESCRIPTION OF WORK

NATIONAL FORESTS IN NORTH CAROLINA PISGAH NATIONAL FOREST PISGAH RANGER DISTRICT PISGAH ROAD WORK 2019

AutoCAD SHX Text

AutoCAD SHX Text

U.S. DEPARTMENT OF AGRICULTURE FOREST SERVICE REGION 8

AutoCAD SHX Text

NFSR 229, PILOT KNOB ROAD DESCRIPTION OF WORK

NATIONAL FORESTS IN NORTH CAROLINA PISGAH NATIONAL FOREST PISGAH RANGER DISTRICT PISGAH ROAD WORK 2019

AutoCAD SHX Text

AutoCAD SHX Text

U.S. DEPARTMENT OF AGRICULTURE FOREST SERVICE REGION 8

AutoCAD SHX Text

NFSR 229, PILOT KNOB ROAD DESCRIPTION OF WORK

NATIONAL FORESTS IN NORTH CAROLINA PISGAH NATIONAL FOREST PISGAH RANGER DISTRICT PISGAH ROAD WORK 2019

AutoCAD SHX Text

AutoCAD SHX Text

U.S. DEPARTMENT OF AGRICULTURE FOREST SERVICE REGION 8

AutoCAD SHX Text

NFSR 229, PILOT KNOB ROAD DESCRIPTION OF WORK

NATIONAL FORESTS IN NORTH CAROLINA PISGAH NATIONAL FOREST PISGAH RANGER DISTRICT PISGAH ROAD WORK 2019

AutoCAD SHX Text

AutoCAD SHX Text

U.S. DEPARTMENT OF AGRICULTURE FOREST SERVICE REGION 8

AutoCAD SHX Text

NFSR 229, PILOT KNOB ROAD DESCRIPTION OF WORK

NATIONAL FORESTS IN NORTH CAROLINA PISGAH NATIONAL FOREST PISGAH RANGER DISTRICT PISGAH ROAD WORK 2019

CULVERT OUTLET PROTECTION

AutoCAD SHX Text

CULVERT

AutoCAD SHX Text NOTES: 1. RIPRAP SHALL BE PLACED BEFORE OR DURING CULVERT INSTALLATION. RIPRAP SHALL BE PLACED BEFORE OR DURING CULVERT INSTALLATION. 2. SHAPE PAD TO BE FLAT / LEVEL FOR ITS WIDTH TO DISPERSE SEDIMENT EVENLY. SHAPE PAD TO BE FLAT / LEVEL FOR ITS WIDTH TO DISPERSE SEDIMENT EVENLY. 3. GEOTEXTILE FABRIC REQUIRED FOR TYPE A OUTLET PROTECTION IS INCIDENTAL TO RIP GEOTEXTILE FABRIC REQUIRED FOR TYPE A OUTLET PROTECTION IS INCIDENTAL TO RIP RAP PLACEMENT.

AutoCAD SHX Text

DIAMETER

AutoCAD SHX Text

ROAD SURFACE

AutoCAD SHX Text

RIPRAP SHALL EXTEND TO CMP INLET INVERT ELEVATION

AutoCAD SHX Text

CULVERT INLET PROTECTION ELEVATION VIEW

AutoCAD SHX Text

EXTEND RIPRAP TO GROUND LINE

AutoCAD SHX Text

SHOULDER ELEVATION

AutoCAD SHX Text

STREAM BED

AutoCAD SHX Text

FILL

AutoCAD SHX Text

SLOPE VARIES

AutoCAD SHX Text Donny

AutoCAD SHX Text Alan

AutoCAD SHX Text Greg

AutoCAD SHX Text Kelly

AutoCAD SHX Text Frank

AutoCAD SHX Text Sharon

AutoCAD SHX Text

CULVERT INLET PROTECTION SECTION PROFILE VIEW

AutoCAD SHX Text 18"

AutoCAD SHX Text

NOTE: RIPRAP QUANTITIES VARY SEE DESCRIPTION OF WORK

AutoCAD SHX Text

END VIEW

AutoCAD SHX Text

PROFILE VIEW

AutoCAD SHX Text

TYPE 1-A GEOTEXTILE FABRIC

AutoCAD SHX Text

ROAD SURFACE

AutoCAD SHX Text

SHOULDER ELEVATION

AutoCAD SHX Text

KEYED RIPRAP CLASS 2

AutoCAD SHX Text

KEYED RIPRAP CLASS 2

AutoCAD SHX Text

NATURAL GROUND

AutoCAD SHX Text

KEYED RIPRAP CLASS 2

AutoCAD SHX Text

%%UDITCH CHECK DAMS

AutoCAD SHX Text

RAILROAD BALLAST

AutoCAD SHX Text B

AutoCAD SHX Text B

AutoCAD SHX Text

RAILROAD BALLAST

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

FLOW

AutoCAD SHX Text

SECTION B-B

AutoCAD SHX Text

ROCK CHECK DAM

AutoCAD SHX Text

2" RAILROAD BALLAST IN AGGREGATE SURFACED SECTIONS OF ROADWAY.

AutoCAD SHX Text

CUT SLOPE

AutoCAD SHX Text

ROADWAY

AutoCAD SHX Text CONSTRUCTION OF DITCH BLOCKS IS INCIDENTAL TO DITCH CONSTRUCTION. DITCH BLOCK SPACING IS SPECIFIED IN THE DESCRIPTION OF WORK.

AutoCAD SHX Text 1:1

AutoCAD SHX Text 2:1

AutoCAD SHX Text

ROADSIDE DITCH SECTION

AutoCAD SHX Text

SLOPE VARIABLE, CONSTRUCT AS STAKED

AutoCAD SHX Text

TYPICAL FRENCH DRAIN SECTION D-D VIEW

AutoCAD SHX Text

TYPICAL FRENCH DRAIN CROSS SECTION VIEW

AutoCAD SHX Text

EXCAVATE AND CONSTRUCT SLOPE USING 6" THICK 3" STONE TO MATCH EXISTING GRADE.

AutoCAD SHX Text 2:1

AutoCAD SHX Text

WRAPPED IN TYPE I GEOTEXTILE

AutoCAD SHX Text D

AutoCAD SHX Text D

AutoCAD SHX Text

TYPE I GEOTEXTILE

AutoCAD SHX Text

CLEAN RAILROAD BALLAST

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

U.S. DEPARTMENT OF AGRICULTURE FOREST SERVICE REGION 8

AutoCAD SHX Text

DRAINAGE TYPICALS

NATIONAL FORESTS IN NORTH CAROLINA PISGAH NATIONAL FOREST PISGAH RANGER DISTRICT PISGAH ROAD WORK 2019

AutoCAD SHX Text

TYPICAL INSTALLATION WITH OUTLET DITCH CROSS SECTION VIEW

AutoCAD SHX Text

CULVERT OUTLET SET BELOW NATURAL GROUND WITH RIPRAP OUTLET PROTECTION

AutoCAD SHX Text

OUTLET "V" DITCH PICTORIAL VIEW

AutoCAD SHX Text

CMP GRADE (+) 1% CUT SLOPE 1 :112:1

AutoCAD SHX Text

2:1 SLOPE

AutoCAD SHX Text

FLOW

AutoCAD SHX Text

EXISTING GROUND

AutoCAD SHX Text

BOTTOM WIDTH MAY VARY WHEN CATCH BASIN IS CONSTRUCTED IN NATURAL DRAINAGE

AutoCAD SHX Text

DITCH WIDTH

AutoCAD SHX Text

SLOPE RATIO AS STAKED

AutoCAD SHX Text 2:1

AutoCAD SHX Text

CULVERT

AutoCAD SHX Text SLOPE RATIO AS STAKED, MINIMUM SLOPE IS SLOPE OF INCOMING DITCH + 1% WHERE PRACTICABLE

AutoCAD SHX Text TOP OF CATCH BASIN CUT SLOPE BOTTOM OF CATCH BASIN CUT SLOPE NORMAL TOP OF CUT SLOPE

AutoCAD SHX Text

EDGE OF ROAD

AutoCAD SHX Text

DITCH BLOCK HEIGHT 6" BELOW SUBGRADE

AutoCAD SHX Text

CULVERT

AutoCAD SHX Text

PLAN VIEW TYPICAL DITCH RELIEF CULVERT

AutoCAD SHX Text NOTES: MATERIAL REMOVED IN THE MAINTENANCE, RECONDITIONING, & CLEANING OF CATCH BASINS & CULVERTS SHALL NOT BE DEPOSITED ON / OR ABOVE CUT SLOPES. MATERIAL MAY BE DEPOSITED NOT BE DEPOSITED ON / OR ABOVE CUT SLOPES. MATERIAL MAY BE DEPOSITED BE DEPOSITED ON / OR ABOVE CUT SLOPES. MATERIAL MAY BE DEPOSITED ON FILL SLOPE TO A DEPTH OF NOT MORE THAN 4 INCHES WHEN APPROVED BY THE CONTRACTING NOT MORE THAN 4 INCHES WHEN APPROVED BY THE CONTRACTING MORE THAN 4 INCHES WHEN APPROVED BY THE CONTRACTING OFFICER. OTHERWISE ALL MATERIAL SHALL BE REMOVED FROM NATIONAL FOREST LANDS IN A LEGAL MANNER OR USED ELSEWHERE AS APPROVED BY THE CONTRACTING OFFICER.

AutoCAD SHX Text

DITCH BLOCK WHERE REQUIRED

AutoCAD SHX Text

FLOW

AutoCAD SHX Text

SECTION A-A DITCH RELIEF CULVERT

AutoCAD SHX Text

SLOPE VARIABLE, CONSTRUCT AS STAKED

AutoCAD SHX Text

SLOPE ROUNDING

AutoCAD SHX Text

DITCH BLOCK

AutoCAD SHX Text

CODY

AutoCAD SHX Text

TYPE 1-A GEOTEXTILE FABRIC

AutoCAD SHX Text

KEYED RIPRAP CLASS 2

AutoCAD SHX Text

CULVERT INLET/OUTLET DITCH TYPICAL

AutoCAD SHX Text Not to Scale

AutoCAD SHX Text A

AutoCAD SHX Text A

AutoCAD SHX Text

FILL SLOPE 1 :1 12:1 OR AS STAKED

AutoCAD SHX Text

WASTE MATERIAL DOWN SLOPE SIDE

AutoCAD SHX Text

ROAD SHOULDER

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

U.S. DEPARTMENT OF AGRICULTURE FOREST SERVICE REGION 8

AutoCAD SHX Text

DRAINAGE TYPICALS 2

NATIONAL FORESTS IN NORTH CAROLINA PISGAH NATIONAL FOREST PISGAH RANGER DISTRICT PISGAH ROAD WORK 2019

AutoCAD SHX Text

OUTLET PROTECTION, SEE NOTE 2

AutoCAD SHX Text

TYPICAL CULVERT FILL SECTION INSTALLATION

AutoCAD SHX Text

SLOPE VARIABLE, CONSTRUCT AS STAKED

AutoCAD SHX Text

BACKFILL, SEE NOTE 1

AutoCAD SHX Text NOTES: 1. BACKFILL ALL CULVERTS WITH SUITABLE MATERIAL APPROVED BY THE CONTRACTING OFFICER. PLACE IN 6-INCH LAYERS, USING BACKFILL ALL CULVERTS WITH SUITABLE MATERIAL APPROVED BY THE CONTRACTING OFFICER. PLACE IN 6-INCH LAYERS, USING COMPACTION METHOD B, IN ACCORDANCE WITH FP-14, 209 STRUCTURE EXCAVATION AND BACKFILL. 2. REFER TO DESCRIPTION OF WORK FOR OUTLET PROTECTION LOCATIONS. REFER TO CULVERT OUTLET PROTECTION SHEET FOR REFER TO DESCRIPTION OF WORK FOR OUTLET PROTECTION LOCATIONS. REFER TO CULVERT OUTLET PROTECTION SHEET FOR CONSTRUCTION INFORMATION. 3. CAMBER ALL CULVERTS AS SHOWN IN CAMBER TYPICAL WITH MAXIMUM CAMBER UNDER CENTER OF FILL. CAMBER ALL CULVERTS AS SHOWN IN CAMBER TYPICAL WITH MAXIMUM CAMBER UNDER CENTER OF FILL. 4. PROVIDE FOR A 25' TRANSITION DITCH INTO INLET OF CULVERT. PROVIDE FOR A 25' TRANSITION DITCH INTO INLET OF CULVERT. 5. ALL EXCAVATION AND TRENCHING OPERATIONS SHALL CONFORM TO OSHA REQUIREMENTS. ALL EXCAVATION AND TRENCHING OPERATIONS SHALL CONFORM TO OSHA REQUIREMENTS. 6. DO NOT OPERATE ANY HEAVY EQUIPMENT OVER ANY CULVERT UNTIL IT HAS BEEN PROPERLY BACKFILLED WITH A MINIMUM OF DO NOT OPERATE ANY HEAVY EQUIPMENT OVER ANY CULVERT UNTIL IT HAS BEEN PROPERLY BACKFILLED WITH A MINIMUM OF 1.5-FOOT COVER. 7. CULVERTS SHALL BE INSTALLED AS STAKED, WITH A MINIMUM OF 8% SLOPE WHERE POSSIBLE. CULVERTS SHALL BE INSTALLED AS STAKED, WITH A MINIMUM OF 8% SLOPE WHERE POSSIBLE. 8. THE MINIMUM LENGTH OF A SINGLE PIPE SECTION FOR ANY INSTALLATION SHALL NOT BE LESS THAN 10 L.F. THE MINIMUM LENGTH OF A SINGLE PIPE SECTION FOR ANY INSTALLATION SHALL NOT BE LESS THAN 10 L.F. 9. FIELD CUTTING OF CULVERT IS NOT PERMITTED UNLESS APPROVED BY THE CONTRACTING OFFICER. WHERE SPELTER COATING HAS FIELD CUTTING OF CULVERT IS NOT PERMITTED UNLESS APPROVED BY THE CONTRACTING OFFICER. WHERE SPELTER COATING HAS BEEN BRUISED OR BROKEN IN THE SHOP, DURING SHIPPING, OR BY FIELD CUTTING REPAIRS SHALL BE IN ACCORDANCE WITH AASHTO M36.

AutoCAD SHX Text

TYPICAL CMP ROUND CULVERT SECTION

AutoCAD SHX Text

12" MINIMUM COVER

AutoCAD SHX Text

TYPICAL CMP ARCH CULVERT SECTION

AutoCAD SHX Text

COMPACT UNDER HAUNCHES

AutoCAD SHX Text

MINIMUM OF 4' + D OR SPAN

AutoCAD SHX Text

MINIMUM EXCAVATION LIMITS

AutoCAD SHX Text

BACKFILL, SEE NOTE 1

AutoCAD SHX Text

MIN. OF 2' + D OR SPAN

AutoCAD SHX Text

UNSUITABLE FOUNDATION

AutoCAD SHX Text

ROCK FOUNDATION

AutoCAD SHX Text

BEDDING, FP-03, 704.02

AutoCAD SHX Text

MIN.

AutoCAD SHX Text

MIN.

AutoCAD SHX Text

MIN.

AutoCAD SHX Text

MIN.

AutoCAD SHX Text

BACKFILL, SEE NOTE 1

AutoCAD SHX Text

TYPICAL BEDDING

AutoCAD SHX Text

BEDDING, FP-03, 704.02

AutoCAD SHX Text

CULVERT AFTER INSTALLATION

AutoCAD SHX Text

TYPICAL CAMBER CROSS SECTION VIEW

AutoCAD SHX Text

CULVERT AFTER SETTLEMENT

AutoCAD SHX Text CAMBER SHALL BE ON A CURVE WITH NO POINT ALONG THE CULVERT BEING HIGHER THAN THE INVERT AT THE INLET MINIMUM CAMBER 1% OF PIPE LENGTH INTRODUCE CAMBER UNDER CENTER OF FILL TO PROVIDE FOR SETTLEMENT

AutoCAD SHX Text 2:1

AutoCAD SHX Text

DO NOT RAISE OUTLET ABOVE STREAM GRADE

AutoCAD SHX Text

TYPICAL STREAM CHANNEL CULVERT INSTALLATION

AutoCAD SHX Text 2:1

AutoCAD SHX Text Not to Scale

AutoCAD SHX Text 1 :112:1

AutoCAD SHX Text

NATURAL STREAM CHANNEL

AutoCAD SHX Text Not to Scale

AutoCAD SHX Text

ROADWAY TYPICALS

AutoCAD SHX Text Not to Scale

AutoCAD SHX Text Not to Scale

AutoCAD SHX Text

FOUNDATION FILL REFER TO FP-03 704.01

AutoCAD SHX Text

12" MINIMUM COVER

AutoCAD SHX Text 2:1

AutoCAD SHX Text

INVERT

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

U.S. DEPARTMENT OF AGRICULTURE FOREST SERVICE REGION 8

AutoCAD SHX Text

CULVERT INSTALLATION TYPICALS

NATIONAL FORESTS IN NORTH CAROLINA PISGAH NATIONAL FOREST PISGAH RANGER DISTRICT PISGAH ROAD WORK 2019

AutoCAD SHX Text

TEMPORARY STRAW SILT CHECKS

AutoCAD SHX Text

TEMPORARY SEDIMENT TRAP SECTION

AutoCAD SHX Text

FILTER FABRIC MIRAFI 140NL OR EQUAL

AutoCAD SHX Text

2"X2"X3' STAKES TO BE LEVEL WITH TOP OF BALE

AutoCAD SHX Text

WOODEN STAKES

AutoCAD SHX Text

LOOSE ROCK

AutoCAD SHX Text

FILTER FABRIC MIRAFI 140NL OR EQUAL

AutoCAD SHX Text

DRAINAGE CHANNEL

AutoCAD SHX Text

TEMPORARY STRAW SEDIMENT TRAP PLAN VIEW

AutoCAD SHX Text

DRAINAGE CHANNEL

AutoCAD SHX Text

ORIGINAL GROUND

AutoCAD SHX Text

KEY INTO THE GROUND 6" MINIMUM

AutoCAD SHX Text NOTES: 1. SEDIMENT BASIN. SEDIMENT BASIN. A. ALL SEDIMENT BASIN CUT AND FILL SLOPES SHALL BE 2:1 OR FLATTER. B. ALL DISTURBED AREAS SHALL BE SEEDED ACCORDING TO APPLICABLE SPECIFICATIONS. C. CLEARING LIMITS SHALL BE APPROVED BY THE CONTRACTING OFFICER PRIOR TO CONSTRUCTION. C. CLEARING LIMITS SHALL BE APPROVED BY THE CONTRACTING OFFICER PRIOR TO CONSTRUCTION. D. MATERIAL FROM EXCAVATION SHALL BE USED TO CONSTRUCT BERM AS SHOWN OR SHALL BE INCORPORATED INTO THE ROAD BED AS APPROVED BY CONTRACTING OFFICER. 2. SILT FENCE. SILT FENCE. A. THE SKIRT TO BE ANCHORED IN A TRENCH 8" DEEP AND 4" WIDE WITH BACKFILL COMPACTED. B. SILT FENCE SHALL BE PREFABRICATED WITH 1- " SQUARE HARDWOOD POSTS, MIRAFI SILT FENCE OR " SQUARE HARDWOOD POSTS, MIRAFI SILT FENCE OR EQUAL. C. INSTALL AS NEEDED FOR EROSION CONTROL OR AS DIRECTED BY THE CONTRACTING OFFICER. 3. TEMPORARY SEDIMENT TRAP. TEMPORARY SEDIMENT TRAP. A. TO BE INSTALLED AT END OF DIVERSION DITCH. B. FILTER FABRIC SHALL BE KEYED INTO GROUND AT A DEPTH OF 8" AND COMPACTED BY HAND TAMPING. C. SEDIMENT TRAPS SHALL BE PLACED PRIOR TO EXCAVATION AND REMOVED AS DIRECTED BY CONTRACTING OFFICER. D. USE A MINIMUM OF 4 BALES FOR EACH TRAP. E. LOOSE ROCKS SHALL BE APPROPRIATE SIZE TO RETAIN FABRIC IN PLACE. LOOSE ROCKS SHALL BE APPROPRIATE SIZE TO RETAIN FABRIC IN PLACE. 4. SEDIMENT CONTROL MEASURES TO BE USED AT LOCATIONS REQUIRED BY THE EROSION CONTROL PLAN, SEDIMENT CONTROL MEASURES TO BE USED AT LOCATIONS REQUIRED BY THE EROSION CONTROL PLAN, AS SHOWN ON THESE PLANS, AND/OR AS DIRECTED BY THE CONTRACTING OFFICER.

AutoCAD SHX Text

GROUND LEVEL

AutoCAD SHX Text 1- " X 1- " POSTS @ 7'-8" 12" X 1- " POSTS @ 7'-8" 12" POSTS @ 7'-8" @ 7'-8" 7'-8" CENTER-TO-CENTER TYPICAL

AutoCAD SHX Text

MIRAFI 100X

AutoCAD SHX Text

SECTION

AutoCAD SHX Text

ELEVATION

AutoCAD SHX Text

FLOW

AutoCAD SHX Text

SILT FENCE DETAILS

AutoCAD SHX Text

DRAWINGS NOT TO SCALE

AutoCAD SHX Text

STRAW BALES

AutoCAD SHX Text

SEDIMENT BASIN PLAN VIEW

AutoCAD SHX Text

SEDIMENT BASIN SECTION A-A

AutoCAD SHX Text

BERM

AutoCAD SHX Text A

AutoCAD SHX Text A

AutoCAD SHX Text

OUTLET DITCH

AutoCAD SHX Text

TOE OF SLOPE

AutoCAD SHX Text

MINIMUM ROCK SIZE 12 CUBIC FOOT

AutoCAD SHX Text

MIRAFI 100X

AutoCAD SHX Text

COMPACTED BACKFILL

AutoCAD SHX Text

BALES TO BUTT TOGETHER

AutoCAD SHX Text

SECTION

AutoCAD SHX Text

PLAN

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

U.S. DEPARTMENT OF AGRICULTURE FOREST SERVICE REGION 8

AutoCAD SHX Text

EROSION CONTROL TYPICALS

NATIONAL FORESTS IN NORTH CAROLINA PISGAH NATIONAL FOREST PISGAH RANGER DISTRICT PISGAH ROAD WORK 2019

WING DITCH TYPICAL

AutoCAD SHX Text NOTE: 1. SEE DESCRIPTION OF WORK FOR WING DITCH SEE DESCRIPTION OF WORK FOR WING DITCH LENGTH & STATION OF WIND DITCH

AutoCAD SHX Text

DOWNGRADE

AutoCAD SHX Text 1.5:1

AutoCAD SHX Text

ROAD

AutoCAD SHX Text

DRAWINGS NOT TO SCALE

AutoCAD SHX Text

DOWNGRADE

AutoCAD SHX Text

ELEVATION DROP ACROSS THE ROLLING DIP SHALL BE 6"

AutoCAD SHX Text

ROLLING DIP PERSPECTIVE VIEW

AutoCAD SHX Text

CREST OF ROLLING DIP

AutoCAD SHX Text

BOTTOM OF ROLLING DIP

AutoCAD SHX Text

PLAN VIEW

AutoCAD SHX Text -4%

AutoCAD SHX Text

ORIGINAL GRADE

AutoCAD SHX Text

ROLLING DIP PROFILE

AutoCAD SHX Text

ROLLING DIP WITH ARMORING

AutoCAD SHX Text

CREST OF ROLLING DIP

AutoCAD SHX Text -4%

AutoCAD SHX Text

ORIGINAL GRADE

AutoCAD SHX Text

ARMORING MATERIAL (SEE NOTE 2)

AutoCAD SHX Text

DOWNGRADE

AutoCAD SHX Text

CLASS B RIPRAP

AutoCAD SHX Text

ROLLING DIP WITH SLOPE PROTECTION

AutoCAD SHX Text

ROLLING DIP WITH OUTLET-DITCH

AutoCAD SHX Text

DOWNGRADE

AutoCAD SHX Text 1.5:1

AutoCAD SHX Text

* SEE DESCRIPTION OF WORK

AutoCAD SHX Text

SUBGRADE

AutoCAD SHX Text

TYPICAL ROAD SURFACE

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

U.S. DEPARTMENT OF AGRICULTURE FOREST SERVICE REGION 8

AutoCAD SHX Text

ROLLING DIP TYPICALS

NATIONAL FORESTS IN NORTH CAROLINA PISGAH NATIONAL FOREST PISGAH RANGER DISTRICT PISGAH ROAD WORK 2019

AutoCAD SHX Text

NATURAL GROUND

AutoCAD SHX Text

ROADBED

AutoCAD SHX Text

TOE OF FILL

AutoCAD SHX Text

SLOPE VARIES

AutoCAD SHX Text

NATURAL GROUND

AutoCAD SHX Text

CLEARING DETAIL FOR DITCHED ROADWAY

AutoCAD SHX Text

ALL DEBRIS FROM CLEARING SHALL BE WINDROWED ALONG THE TOE OF FILL SLOPE

AutoCAD SHX Text

TO TOP OF SLOPE FOR DISTANCE UP TO 10'

AutoCAD SHX Text

TO TOE OF SLOPE FOR DISTANCE UP TO 10'

AutoCAD SHX Text ALL VEGETATION IN ROADBED SHALL BE CLEARED AND GRUBBED. ALL OTHER VEGETATION WITHIN THE CLEARING LIMITS SHALL BE CUT TO WITHIN 6 INCHES OF GROUND LEVEL WITHIN ROADWAY AND WITHIN STATED LIMITS ON FILL AND CUT SLOPES.

AutoCAD SHX Text

NATURAL GROUND

AutoCAD SHX Text

TOE OF FILL

AutoCAD SHX Text

SLOPE VARIES

AutoCAD SHX Text

ALL DEBRIS FROM CLEARING SHALL BE WINDROWED ALONG THE TOE OF FILL SLOPE

AutoCAD SHX Text

TO TOP OF SLOPE FOR DISTANCE UP TO 10'

AutoCAD SHX Text

TO TOE OF SLOPE FOR DISTANCE UP TO 10'

AutoCAD SHX Text

CLEARING DETAIL FOR OUTSLOPED ROADWAY

AutoCAD SHX Text 3%

AutoCAD SHX Text 3%

AutoCAD SHX Text 3:1

AutoCAD SHX Text 3:1

AutoCAD SHX Text 3%

AutoCAD SHX Text 3%

AutoCAD SHX Text 1.3(V):1(H)

AutoCAD SHX Text

1(V):1(H) MAXIMUM

AutoCAD SHX Text 3%

AutoCAD SHX Text

ABC STONE

AutoCAD SHX Text

ROADBED

AutoCAD SHX Text

1(V):1(H) MAXIMUM

AutoCAD SHX Text

SEE DESCRIPTION OF WORK

AutoCAD SHX Text 3:1

AutoCAD SHX Text 3%

AutoCAD SHX Text

1.3(V):1(H) MAXIMUM

AutoCAD SHX Text ALL VEGETATION IN ROADBED SHALL BE CLEARED AND GRUBBED. ALL OTHER VEGETATION WITHIN THE CLEARING LIMITS SHALL BE CUT TO WITHIN 6 INCHES OF GROUND LEVEL WITHIN ROADWAY AND WITHIN STATED LIMITS ON FILL AND CUT SLOPES.

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

U.S. DEPARTMENT OF AGRICULTURE FOREST SERVICE REGION 8

AutoCAD SHX Text

ROADWAY TYPICALS

NATIONAL FORESTS IN NORTH CAROLINA PISGAH NATIONAL FOREST PISGAH RANGER DISTRICT PISGAH ROAD WORK 2019