1240LS25Q0052 GAOA Pleasant Creek Water System Combined Synopsis RFQ.pdf

Solicitation Number: 1240LS25Q0052 GAOA Materials for the Pleasant Creek Water System

(i) This is a combined synopsis/solicitation for commercial items prepared in accordance with the format in subpart 12.6 of the Federal Acquisition Regulation (FAR), as supplemented with additional information included in this notice. This announcement constitutes the only solicitation; proposals are being requested, and a written solicitation will not be issued.

(ii) This solicitation is issued as a Request for Quotation (RFQ).

(iii) The solicitation document and incorporated provisions and clauses are those in effect through Federal Acquisition Circular 2025-04.

(iv) This procurement is set aside for 100% Total Small Business. The NAICS code is 332913 Plumbing Fixture Fitting and Trim Manufacturing and the Small Business Size Standard is 1,000 employees.

(v) Schedule of Items/Price Schedule

Item Supplies/Services Qty Unit of Issue Unit Price Total Price

133400-1 Materials for Utility Box with Water Meter

2 EA $ $

133400-2 Materials for Utility Box with Pressure Reducing Valve

1 EA $ $

221100-1 Potable Water Pipeline, 2” HDPE, 200 PSI with Heat Fusion Joints

5,900 LF $ $

221100-2 Potable Water Pipeline, 3” HDPE, 200 PSI with Heat Fusion Joints

4,500 LF $ $

221100-3 Materials for a 2” Daylight Drain 3 EA $ $

221100-4 Materials for a Pump-Out Drain 1 EA $ $

221102-1 2” Poly Curb Valve and Box 16 EA $ $

221102-2 3” Poly Curb Valve and Box 5 EA $ $

221105-1 Materials for Water Hydrant – Type A, with Pad

6 EA $ $

221105-2 Materials for Water Hydrant – Type B, with Pad

3 EA $ $

221105-3 Materials for a Water Hydrant – Type C, with Pad

1 EA $ $

Additional Items

221200-1 Tank (A) Oak Creek Tank:

Stainless Steel Potable Water Tank – 2,000 Gallons

2 EA $ $

221200-2 Tank (B) Main Spring Tank:

Stainless Steel Potable Water Tank – 4,000 Gallons

1 EA $ $

0014 Delivery 1 LS $ $

Total: $

Indicate ability to deliver by the date listed in section (vii), Y or N:

If unable to delivery by this date, indicate earliest possible award date based on an anticipated award date of 09/17/2025:

Quoter’s Company Information

Company Name (Please Print):

UEI NUMBER from SAM.gov

Printed Name of Company Representative:

Signature of Company Representative:

Date:

Phone Number:

Email Address:

Schedule Notes:

a) Items labeled as optional are not required to be exercised by the government. If exercised, the contractor will be required to perform the optional work in accordance with the terms and conditions of this contract.

b) One award will be made from this solicitation, contractors must submit pricing for all items.

c) EA= Each; LF = Linear Feet.

(vi) Description of Requirement – This Requirement is for Supplies Only.

The salient characteristics of any specified brand name item are those specifications listed in the respective sub-section of this description section. An equal item must meet all specifications listed for that item to be considered equal.

SECTION 010250 - CONSTRUCTION STAKING

SECTION 133402 - UTILITY BOXES

SECTION 221100 - WATER DISTRIBUTION SYSTEMS

SECTION 221102 - CURB VALVES AND BOXES

SECTION 221103 - PLUMBING APPURTENANCES

SECTION 221105 - WATER HYDRANTS

SECTION 221200 - UNDERGROUND WATER STORAGE TANK

USDA FOREST SERVICE, R4

GAOA FISHLAKE CAMPGROUND WATER SYSTEM DEFERRED MTNC PHASE 2 SECTION 133402 -

UTILITY BOXES

PART 1 - GENERAL

1.1 MANHOLES

A. Normal-Traffic Precast Concrete Manholes: ASTM C478, precast, reinforced concrete, of depth indicated, with provision for rubber gasketed joints.

1. Diameter: 48 inches minimum, unless otherwise indicated.

2. Base Section: Open bottom with 5-inch minimum thickness for walls and base riser section.

3. Riser Sections: 5-inch minimum thickness, and lengths to provide depth indicated.

4. Top Section: Eccentric-cone type. Top of cone of size that matches grade rings.

5. Grade Rings: Include maximum of two reinforced-concrete rings, for a maximum height of 6-inches, that match 24-inch-diameter frame and cover.

6. Steps shall be a ½-inch steel rod encapsulated with polypropylene, 12-inch step, 10 inches center to center leg distance x 5 ¾-inches projection, designed for installation into precast concrete. Steps shall be Model PS1 as manufactured by M.

A. Industries, or approved equal.

7. Pipe Connectors: Each pipe connection to manhole shall be made with pipe-to- manhole flexible connector system for use with cored holes in concrete manhole or tank, made of a polyisoprene rubber resilient connector meeting ASTM C-923, with type 304 stainless steel compression clamps. Connector system shall be PSX:Direct Drive in appropriate size as manufactured by Press-Seal Gasket Corporation, or approved equal.

8. Manhole Frames and Covers: Lockable, ASTM A48 CL35, grey iron castings. Watertight bolted and gasketed cover to eliminate infiltration. Cover shall have a minimum of 2 pick bar locations. Frame shall have a minimum 30 ID by minimum 5-inch riser with 3-inch minimum width flange, and minimum 30-inch-diameter cover, sized to fit on manhole top section. Include indented top design with lettering “WATER” cast into cover. Frame and cover shall be 1342 series as manufactured by East Jordan Iron Works, Inc., or approved equal.

9. Mastic Joint Sealant: Preformed flexible joint gasket meeting all requirements of ASTM C990.

Sealant shall be RAM-NEK as manufactured by Henry Company, or approved equal.

10. Non-Shrink Grout: Cement based non-shrink grout, Materflow 713 Plus, by Degussa Building Systems, or approved equal.

1.2 LOCKING MECHANISM

A. Provision shall be made to secure the lid to the box using vandal resistant bolts.

1.3 WELDED WIRE MESH

A. For burrowing rodent control under the box. Galvanized, ½” welded wire mesh, 19 gauge.

1.4 CONCRETE SUPPORTS

A. Plumbing appurtenances shall be supported using concrete blocks under adjustable stands as shown on the Drawings. Blocks and stands shall be approved by the Contracting Officer.

1.5 PLUMBING APPURTENANCES

A. According to Section 221103 “Plumbing Appurtenances.”

END OF SECTION 133402

April 2025

SECTION 221100 - WATER DISTRIBUTION SYSTEMS

1.6 QUALITY ASSURANCE

A. Piping materials shall bear label, stamp, or other markings of specified testing agency.

B. NSF Compliance:

1. Comply with NSF 14 for plastic potable-water-service piping. Include marking "NSF-pw" on piping.

2. Comply with NSF 61 for materials for water-service piping and specialties for domestic water.

1.7 MINIMUM SYSTEM REQUIREMENTS

A. Unless otherwise noted, the minimum working pressure for piping and specialties shall be 160 psig.

1.8 DELIVERY, STORAGE AND HANDLING

A. Deliver piping with factory-applied end caps. Maintain end caps through shipping, storage, and handling to prevent pipe-end damage and to prevent entrance of dirt, debris, and moisture.

B. Protect stored piping from moisture and dirt. Elevate above grade.

C. Protect flanges, fittings, and specialties from moisture and dirt.

D. Store plastic piping protected from direct sunlight. Support to prevent sagging and bending.

PART 2 - PRODUCTS

2.1 GENERAL

A. All waterlines, pipes, and fittings shall be new and unused, of the type, pressure rating or class, and size specified and as shown on the Drawings.

B. HDPE:

1. Pipe, AWWA C901:

a. Material Designation: PE 4710 resin

b. Minimum Cell Classification: ASTM D 3350, 445574C

c. Dimension Ratio and Minimum Pressure Rating: IPS DR9, 250 psig.

2. Fittings:

a. Molded HDPE Fittings: ASTM D 3350, PE 4710 resin, butt-fusion type, made to match HDPE pipe dimensions and class.

b. Insert Fittings: Not allowed.

c. Transition Fittings to non-HDPE Pipe: Approved by HDPE pipe manufacturer. Compression-type fittings are not allowed.

3. Pipe Larger than 3-inch Diameter: Provide in 40-foot lengths rather than in rolls.

4. Pipe and Fittings 4-inch Diameter and Larger: Conform to AWWA C906 in addition to above requirements.

C. Galvanized Steel: ASTM A53, Schedule 40, threaded ends meeting ASME B1.20.1.

USDA FOREST SERVICE, R4

GAOA FISHLAKE CAMPGROUND WATER SYSTEM DEFERRED MTNC PHASE 2 SECTION 221102 -

CURB VALVES AND BOXES

PART 3 - PRODUCTS

3.1 CURB VALVES AND BOXES

A. Valves: Valves shall be the same nominal size as the line in which they are installed or as indicated on the Drawings.

1. Valve Operating Wrenches: Steel, tee-handle with one pointed end, stem of length to operate deepest buried valve, and end matching curb valve. Furnish one valve operating wrench or shut-off rod with every five (or fraction thereof) curb boxes installed, as indicated on the Drawings.

a. Valve Operating Extension for Poly Valves: Polyethylene or PVC, with adapter to fit valve, extend to within 4 inches of ground level.

2. Poly Valves

a. NSF Approved (Potable water systems only)

b. Valves 4-Inch and Larger: AWWA C906.

c. Valves Smaller Than 4-inch: Similar quality to AWWA C906.

d. Opening (Bore): Full.

e. Dimension Ratio and Pressure Rating: Same as pipe in which the valve is installed

f. Model: Poly-Water Valves, as manufactured by Nordstrom Audco Inc., or an approved equal.

B. Curb Boxes:

1. Lids: Lockable, with pentagon-type bolt, compatible with valve box; labeled “WATER” or “SEWER” respectively.

2. Pentagon Lid Keys: Furnish one key with every five (or fraction thereof) curb boxes installed.

3. Curb Boxes for Poly Valves:

a. Design: Slider or screw type, Buffalo pattern.

b. Bottom Sections: Compatible with valve.

c. For 1-Inch Valves: 2-1/2-Inch shaft, Series 200 or 250 Plastic Boxes, with #002 bottom sections, as manufactured by Bingham and Taylor or an approved equal.

d. For 2-Inch Through 6-Inch Valves: 5-1/4-Inch shaft, Series 500 Plastic Boxes, as manufactured by Bingham and Taylor or an approved equal.

1) Bottom Sections for 2” or 3” Valves: #104

2) Bottom Sections for 4” Valves: #105

3) Bottom Sections for 6” Valves: #108

END OF SECTION 221102

USDA FOREST SERVICE, R4

GAOA FISHLAKE CAMPGROUND WATER SYSTEM DEFERRED MTNC PHASE 2 SECTION 221103 -

PLUMBING APPURTENANCES

PRODUCTS

3.2 GENERAL

A. All plumbing appurtenances shall be new and unused, of the type, pressure rating or class, and size specified and as show on the Drawings.

3.3 WATER METER

A. Description: AWWA C700, displacement-type, low-lead bronze main case, NSF-61 certified.

Register flow in gallons unless cubic feet are indicated.

B. Model: 1” Low Lead SR as manufactured by Sensus Metering Systems, or an approved equal.

3.4 BALL VALVE

A. Description: Bronze, 400 psi, threaded NPT end connections.

B. Model: LFB6000 Lead Free Ball Valve as manufactured by Watts Regulator, or an approved equal.

3.5 GLOBE VALVE

A. Description: Threaded, 150 psi, union bonnet, renewable composition disc with integral seat, with bronze body.

B. Model: Powell Class 150 as manufactured by Wm. Powell Company, or No. 7, as manufactured by the Crane Company, Chicago, or an approved equal.

3.6 HOSE BIBB

A. Description: Rough brass finish, male inlet, 3/4-inch hose thread outlet.

B. Model: Manufactured by Arrowhead Brass Products, Chicago Faucet Company, or an approved equal.

1. Vacuum Breaker: Model #LF8A Lead Free, ASSE 1011, Non-removable vacuum breaker, as manufactured by Watts Regulator Company, or an approved equal.

2. Hose: Provide 5-foot length of 3/4-inch plastic hose for connection to vacuum breaker.

3.7 CHECK VALVE

A. Description: Bronze, AWWA C508, swing-check type with 125-psig working-pressure rating, threaded ends, screwed-in cap, renewable brass disc and resilient seat. Include interior coating according to AWWA C550 and ends to match piping.

B. Model: Figure No. 578 as manufactured by Powell Company, or an approved equal.

3.8 UNION

A. Description: Female type, malleable iron, 150 pound, with ground brass to iron seat.

B. Model: Manufactured by Crane Company, or an approved equal.

3.9 PRESSURE GAUGE

A. Description: 2-inch diameter or larger, 0 to 200 psi range, with brass movement, steel case and bottom mounting with NPS 0.25 threads. Include 1/4” ball valve for gauge isolation.

B. Model: Ashcroft Model 1000 or 1005 as manufactured by Dresser Industries, or an approved equal

3.10 SAMPLE TAP

A. Description: Brass, 1/2-inch hose bib with male inlet and smooth-nosed outlet.

B. Model: P/N 301PE as manufactured by Arrowhead Brass, or an approved equal.

3.11 WYE-STRAINER

A. Description: 125 psi minimum working pressure, semi-steel or bronze body with threaded ends, with brass plug in blow-off connection and removable stainless steel #30 mesh screen.

B. Model: Style B or F, as manufactured by O. C. Keckley Company, or Model: P/N LF777S, as manufactured by Watts Regulator Company, or an approved equal.

3.12 PRESSURE TANK

A. Description: Pneumatic.

1. Total Volume: 2 gallons.

2. Maximum Acceptance Factor: 0.45.

3. Precharge Pressure: 20 psi or according to the Drawings.

4. Meets NSF/ANSI 61.

5. Maximum Working Pressure: 150 psig.

B. Model: Well-X-Trol WX-101 as manufactured by Amtrol, Inc. or an approved equal.

3.13 PIPE AND FITTINGS

A. Galvanized Steel: ASTM A53, Schedule 40, threaded ends meeting ASME B1.20.1.

1. Fittings: Threaded, ASTM A 338.

3.14 PRESSURE RELIEF VALVE FOR USE WITH PRESSURE-REGULATING VALVES

A. Description: Direct acting, spring loaded, diaphragm type pressure relief valve.

B. Pressure Range: 20 to 105 psi

C. Size: 3/4-inch

D. Model: 55F as manufactured by Cla-Val Company, or an approved equal.

3.15 PRESSURE REGULATING VALVE FOR DISTRIBUTION SYSTEM PIPELINES

A. Description

1. Valve Size: 1 inch

2. Pattern: Globe

3. End: Threaded, NPT, ANSI B2.1.

4. Outlet Pressure Range: 20 to 105 psi

5. Min. Continuous Flow: 1 GPM

6. Max. Continuous Flow: 55 GPM

7. Max. Intermittent Flow: 68 GPM

8. Temperature Range: Water to 180 deg F.

9. Rated Working (Inlet) Pressure: 250-psig or greater.

10. Accessories:

a. With direct-action pilot valve

b. With Flow Strainer on inlet

c. Inlet Pressure Gauge (0-150 psi)

d. Outlet Pressure Gauge (0-150 psi)

e. CV Flow Control (Opening)

11. Coating: Epoxy coated interior and exterior

B. Model: 90-01-ASPKC as manufactured by Cla-Val Company, or an approved equal.

C. Substitutions for this model could have substantial effects on the hydraulic performance of the water system.

3.16 SUPPORTS FOR PIPES AND APPURTENANCES

A. Description: Galvanized steel framing system, pipe clamps and hangers.

B. Manufacturer: Unistrut Corporation or an approved equal. END OF

SECTION 221103

GAOA FISHLAKE CAMPGROUND WATER SYSTEM DEFERRED MTNC PHASE 2 SECTION 221105 -

WATER HYDRANTS

PART 1 - GENERAL

1.1 SUMMARY

A. Provides for furnishing hydrants as follows:

1. Type A: A self-closing faucet.

2. Type B: A self-closing faucet and hose bibb with backflow preventer.

3. Type C: Two hose bibbs, upper bibb with vacuum breaker, lower bibb with backflow preventer.

1.2 DELIVERY, STORAGE, AND HANDLING

A. Products shall be kept free from damage during delivery, storage, and handling. Protect from dirt and moisture during storage.

1.3 QUALITY ASSURANCE

A. NSF Compliance:

1. All products in contact with potable water shall comply with NSF 61 Annex G. All pipes, fittings, fixtures, solder and flux shall meet the 0.25% maximum lead content rules for all wetted components.

PART 2 - PRODUCTS

2.1 GENERAL MATERIALS

A. Lumber: S4S, Redwood, construction grade, meeting requirements of Redwood Inspection Service.

B. Lumber: S4S, Cedar, No. 1

C. Stain: Moorwood solid color stain as manufactured by Benjamin Moore & Co. or an approved equal.

1. Color: Forest Service “Brown.” Contractor shall submit color sample to the Contracting Officer for approval.

D. Framing Anchors: 16 gage, galvanized, 3-1/4 inches high with 1-1/4 inch long flanges

1. Model: GA2 model angle connector, as manufactured by Simpson Strong, or an approved equal.

E. Galvanized Steel Drain Grate

1. Design: 1/2” x 2” on-center press-locked close mesh, ADA compliant, hot-dipped galvanized steel, and 1-1/2” depth with welded lugs. Length and width shall be as shown on the Drawings.

2. Model: 8-P-2 as manufactured by Alabama Metal Industries Corporation (AMICO), or an approved equal.

2.2 FOREST SERVICE STANDARD HYDRANTS (TYPES A, B & C)

A. Pipe and Fittings: As specified in Section 221100 “Water Distribution System.”

1. Galvanized Steel Pipe and Fittings: Schedule 40.

B. Plumbing Appurtenances

1. Self-Closing Faucet

a. Design: 1/2-inch, plain end, chrome or rough brass finish, self-closing lever handle, ADA compliant, certified lead-free.

b. Model: 6252EHLF, as manufactured by Haws Corporation, or an approved equal.

2. Hose Bibb

a. Design: 1/2-inch FIP, rough brass finish, loose key lockshield, with backflow preventer, certified lead-free.

b. Model: 253BFPLK “No Kink”, as manufactured by Arrowhead Brass Products, Inc., or an approved equal.

c. Provide two operating keys for first five hydrants, then one additional key for each additional five hydrants.

3. Stop Valve

a. Design: 3/4-inch curb valve, with removable key, FIP thread and drain.

b. Model: Mark II H-10284 as manufactured by the Mueller Company, or an approved equal.

c. Provide two operating keys for first five hydrants, then one additional key for each additional five hydrants.

4. Backflow Preventer

a. Design: 1/2-inch, ASSE 1024, CSA B64.6, bronze-bodied, dual check.

b. Model: Series 7, as manufactured by Watts Regulator Company, or an approved equal.

c. Location: Attach to lower hose bibb, as shown on the Drawings.

5. Vacuum Breaker

a. Design: ASSE 1011, Brass body, anti-siphon, non-removeable, 3/4-inch HTF inlet, 3/4-inch HTM outlet.

b. Model: 8A, as manufactured by Watts Regulator, or an approved equal.

PART 3 - EXECUTION

3.1 FOREST SERVICE STANDARD HYDRANT INSTALLATION

A. Fabricate hydrant post, frame, sump, grate and pad as shown on the Drawings.

B. Wood Posts: Cut and drill to required lengths and chamfer, as shown on the Drawings. All exposed corners shall be lightly rounded and the surfaces finished smooth. Apply two coats of stain to portion of post that will be above ground.

C. Stain finishes on the post, if damaged during installation, shall be touched up or repaired. Stain shall not be spattered on the pipe and fittings.

3.2 GENERAL INSTRUCTIONS

A. Pipe and Fittings: Pipe and fittings shall be watertight. If any appurtenances are not rated for the pressure required for pressure testing the pipelines, ensure hydrant will be isolated from the pipeline during pressure testing.

END OF SECTION 221105

GAOA FISHLAKE CAMPGROUND WATER SYSTEM DEFERRED MTNC PHASE 2 SECTION 221200 -

UNDERGROUND WATER STORAGE TANK

PART 1 - GENERAL

1. Submit Storage tank shop Drawings, include the following (fabrication of the tank shall begin after shop Drawings have been approved by the Contracting Officer):

a. Access opening and cover fabrication, location, dimensions, and methods of connection.

b. Nozzle fabrication, location, and methods of connection.

c. Ladder location, dimensions, and methods of connection.

2. Storage tank manufacturer’s data sheets and installation instructions.

3. Certification from tank manufacturer that the tank, ladder, access opening, and nozzles were manufactured with materials conforming to the requirements of NSF 61.

4. Certification from the tank manufacturer that the tank was tested by the manufacturer at the factory and meets the design criteria specified.

5. Flexible Connectors.

6. Stainless Steel Tanks: Paint manufacturer literature for exterior coatings including name, general type, solids by volume, and recommended dry film thickness.

7. Operation and Maintenance Data: Storage tank and related accessories.

1.2 QUALITY ASSURANCE

A. NSF Compliance:

1. The storage tank, ladder, nozzles and all other components in contact with potable water shall be manufactured with materials conforming to the requirements of NSF 61 Annex G.

2. All pipes, fittings, fixtures, solder and flux shall meet the 0.25% maximum lead content rules for all wetted components.

1.3 STAINLESS STEEL WATER STORAGE TANK

A. Available Manufacturers (or an approved equal):

1. Rule Steel Tanks, Inc.

2. Continental Steel Works, Inc.

B. Design Criteria:

1. The shop fabricated water storage tank shall be a cylindrical horizontal stainless steel water storage tank constructed of welded 304 or 316 stainless steel meeting ASTM A167 or ASTM A240 with the following thickness (see Table 1):

Table 1 – Steel Plate Thickness

Capacity of Tank Steel Plate Thickness

1,000 to 3,999 gallons 3/16 inch

4,000 to 11,999 gallons 1/4 inch

12,000 to 30,000 gallons 3/8 inch

2. The tank shall be constructed in accordance with Underwriter’s Laboratories, Inc., UL 58 and with NSF 61. Exceptions to UL 58: The tank shall have wedge bar lids as shown on the drawings rather than bolt down lids. The tank need not be UL approved or have the UL label.

3. Exterior Coating

a. Coating: Corchem 247 coal tar epoxy, as manufactured by Corchem Corporation, or an approved equal.

b. Surface Preparation: Round off sharp edges and rough welds. Surfaces must be clean, dry and free of any rust, dirt, chalk, grease, oil, etc. All surfaces shall be blasted with abrasive grit to near-white in accordance with the Society of Protective Coatings Standard SSPC-SP 10.

c. Application: Exterior surfaces shall be given two coats, 15 mil wet, 8 mil minimum thickness dry, for a total minimum dry thickness of 16 mil. The dry film thickness shall be verified in the presence of the Contracting Officer with a magnetic gauge in accordance with SSPC-PA 2. Test equipment shall be furnished by the Contractor.

4. External Hydrostatic Pressure and Burial Depth: Tank shall be designed to withstand burial in ground with 7 feet of saturated soil overburden over the top of the tank, with a safety factor of 5:1 against general buckling.

5. Tank shall support accessory equipment such as ladders, submersible pumps, liquid level probes, etc.

6. The tank shall be fabricated with the correct number of threaded openings of the proper sizes to accommodate the pipes, valves, and controls as shown on the drawings.

7. Tank shall be vented to atmospheric pressure, as the tank is not a pressure vessel.

1.4 ACCESSORIES

A. Access Openings and Covers

1. Access opening cover or lid shall be insect proof, overlapping, and water tight with O-ring and/or gasket. The lid must extend down the frame at least two inches and must cover the entire opening. Provide a locking device.

2. Identification: Label access opening cover or lid with sign reading “DANGER – CONFINED SPACE, ENTER BY PERMIT ONLY” or other similar language approved by the Contracting Officer. Sign must be permanently mounted in a clearly visible location on the access opening cover.

3. Lock will be supplied and installed by the Forest Service.

B. Ladder

1. NSF 61

2. Welded 304 or 316 stainless steel (ASTM A167 or A240).

3. Provide ladder extending from the top of the access opening to the bottom of the tank as shown on the Drawings.

4. The ladder shall have the ability to expand and contract without stressing the tank walls.

5. Dimensions: Minimum width of 12 inches and maximum rung spacing of 12 inches.

6. Ladder design shall meet all applicable federal and state standards, including

Occupational and Safety Health Administration (OSHA).

C. Nozzles and Flanges

1. NSF 61

2. Material:

a. Stainless Steel Tanks: Stainless Steel

3. Tanks shall be furnished with all nozzles, flanges, and other appurtenances as shown on the Drawings.

4. Threads on nozzles shall be standard NPT.

D. Lifting Lugs

1. Lifting lugs shall be provided as recommended by the manufacturer and shall be an integral part of the tank.

E. Flexible Connectors

1. Install one flexible connector on all 4-inch diameter and larger HDPE pipes within 3 feet of the tank flange

2. Provide connectors as described above for each pipe connected to the tank, including the inlet, outlet, overflow and vent pipes.

3. Design: NSF 61, gasketed, sleeve-type design, with diameter to properly fit the pipe, suitable for direct-bury application.

4. Model: Dresser-style coupling as distributed by World Wide Metric, Inc. or an approved equal.

1.5 BAGGED ANODES (FOR STAINLESS STEEL TANKS)

1. The steel tank shall be installed with magnesium anode packs according to Table 2.

Table 2

Storage

Capacity

(Gallon)

Number of Anode

Packs

Less than 2,000 1

2,000 to 4,000 2

4,001 to 8,000 3

Greater than 8,000 4

2. Anode: High pure magnesium each having a plated steel core with 14 feet of #12 THHN insulated lead wire attached with silver solder; packaged, having backfill mixture consisting of 75% gypsum, 20% western bentonite, and 5% sodium sulfate.

3. Model: 17-pound CPAN-08-HP17, as manufactured by Clay and Bailey Manufacturing Company, or an approved equal.

1.6 VENT

A. Galvanized steel pipe vent turned down with a non-corrosive, No. 24 galvanized steel wire insect screen on turned down end. Transition to galvanized pipe 12” below grade. Pipe shall meet the requirements of Section 221100 “Water Distribution System.”

1.7 CURB VALVES AND BOXES

A. Curb Valves and Boxes shall be according to Section 221102 “Curb Valves and Boxes.”

1.8 FILTER FABRIC

1.9 LIQUID LEVEL SENSORS (PROBES) AND FLOAT SWITCHES

A. Liquid level sensors or probes and float switches shall be as shown on the Drawings.

B. Support Bracket: The flange required for the liquid sensors hub shall be an integral part of the tank or shall be manufactured and installed as required by the tank manufacturer.

C. Electrical Entrance: Electrical entrance for the floats shall be an integral part of the tank access opening or shall be manufactured and installed as required by the tank manufacturer. The access opening penetration shall be:

1. Located 6-inches minimum above final grade and where box with floats will not interfere with climbing the ladder.

2. ½-inch IMC or RSC conduit, threaded both ends.

a. Install a conduit supported NEMA Type 4X ABS Enclosure, minimum 4”x2”x2” high, capable of two 1/2-inch conduit entrances in bottom for float connections, on access interior side.

b. Exterior side shall electrical connections shall be with a 90-degree elbow to LFMC or LFNC long enough to provide for +2-inches and -4-inches of movement relative to metal conduit stub-up at access cover. See specification 260533.

3. Sealed waterproof around the penetration on both sides and including enclosure.

4. Able to support 500 pounds on exterior of access without damage.

1.10 GRADE LEVEL ACCESS BOX

A. Boxes to be made of plastic or other non-corroding material, listed for the location installed.

1.11 NON-MODULATING FLOAT VALVE

A. Description: Hydraulically operated diaphragm float valve, with cast-iron or bronze body; with stainless steel, bronze or monel working parts, renewable valve seat and adjustable float; size and pressure rating as shown on the Drawings. The valve shall open fully at a pre-set low float level, flow at a full rate until reaching the pre-set high float level, and then close drip-tight without slamming.

B. Model: No. 124-01 Non-Modulating Float Valve with No. CF1-C1 Float Control, as manufactured by Cal-Val Company, or an approved equal.

END OF SECTION 221200

SEPTEMBER 2020

(vii) Date(s) and Place(s) of Delivery and Acceptance/Location

10/15/2025; 207 South Main Street Teasdale, UT 84773

CLAUSES:

(viii) FAR 52.252-2 Clauses Incorporated by Reference (FEB 1998)

This contract incorporates one or more clauses by reference, with the same force and effect as if they were given in full text. Upon request, the Contracting Officer will make their full text available. Also, the full text of a clause may be accessed electronically at this/these address(es):

Federal Acquisition Regulation (FAR): https://www.acquisition.gov/browse/index/far (Clauses are located at FAR part 52 and begin with 52)

Department of Agriculture Acquisition Regulation (AGAR):https://www.acquisition.gov/agar (Clauses are located at AGAR part 452 and begin with 452) https://www.acquisition.gov/browse/index/far https://www.acquisition.gov/far/part-52 https://www.acquisition.gov/agar https://www.acquisition.gov/agar/part-452-solicitation-provisions-and-contract-clauses

Deviations to clauses may be viewed at: USDA FAR Class Deviations

Clauses Incorporated by Reference:

(ix) FAR 52.212-4 Contract Terms and Conditions – Commercial Products and Commercial Services

(NOV 2023)

Addenda to FAR 52.212-4:

FAR 52.204-13 System for Award Management Maintenance (OCT 2018) FAR 52.204-18 Commercial and Government Entity Code Maintenance (AUG 2020) FAR 52.242-15 Stop-Work Order (AUG 1989) FAR 52.242-17 Government Delay of Work (APR 1984) FAR 52.249-8 Default (Fixed-Price Supply and Service)(APR 1984) AGAR 452.204-70 Modification for Contract Closeout

(x) FAR 52.212-5 Contract Terms and Conditions Required to Implement Statutes or Executive Orders – Commercial Products and Commercial Services (JAN 2025) (DEVIATION FEB 2025)

(a) The Contractor shall comply with the following Federal Acquisition Regulation (FAR) clauses, which are incorporated in this contract by reference, to implement provisions of law or Executive orders applicable to acquisitions of commercial products and commercial services:

(1) FAR 52.203-19, Prohibition on Requiring Certain Internal Confidentiality Agreements or Statements (JAN 2017) (section 743 of Division E, Title VII, of the Consolidated and Further Continuing Appropriations Act, 2015 (Pub. L. 113-235) and its successor provisions in subsequent appropriations acts (and as extended in continuing resolutions)).

(2) FAR 52.204-23, Prohibition on Contracting for Hardware, Software, and Services Developed or Provided by Kaspersky Lab Covered Entities (DEC 2023) (Section 1634 of Pub. L. 115-91).

(3) FAR 52.204-25, Prohibition on Contracting for Certain Telecommunications and Video Surveillance Services or Equipment. (NOV 2021) (Section 889(a)(1)(A) of Pub. L. 115-232).

(4) FAR 52.209-10, Prohibition on Contracting with Inverted Domestic Corporations (NOV 2015).

(5) FAR 52.232-40, Providing Accelerated Payments to Small Business Subcontractors (MAR

2023) (31 U.S.C. 3903 and 10 U.S.C. 3801).

(6) FAR 52.233-3, Protest After Award (AUG 1996) (31 U.S.C. 3553).

(7) FAR 52.233-4, Applicable Law for Breach of Contract Claim (OCT 2004) (Public Laws 108-77 and 108-78 (19 U.S.C. 3805 note)).

(b) The Contractor shall comply with the FAR clauses in this paragraph (b) that the Contracting Officer has indicated as being incorporated in this contract by reference to implement provisions of law or Executive orders applicable to acquisitions of commercial products and commercial services:

☐ (1) FAR 52.203-6, Restrictions on Subcontractor Sales to the Government (JUN 2020), with

Alternate I (NOV 2021) (41 U.S.C. 4704 and 10 U.S.C. 4655).

☐ (2) FAR 52.203-13, Contractor Code of Business Ethics and Conduct (NOV 2021) (41 U.S.C.

3509)).

☐ (3) FAR 52.203-15, Whistleblower Protections under the American Recovery and

Reinvestment Act of 2009 (Jun 2010) (Section 1553 of Pub. L. 111-5). (Applies to contracts funded by the American Recovery and Reinvestment Act of 2009.)

☒ (4) FAR 52.203-17, Contractor Employee Whistleblower Rights (NOV 2023) (41 U.S.C. 4712);

this clause does not apply to contracts of DoD, NASA, the Coast Guard, or applicable elements of the intelligence community—see FAR 3.900(a).

☒ (5) FAR 52.204-10, Reporting Executive Compensation and First-Tier Subcontract Awards

(Jun 2020) (Pub. L. 109-282) (31 U.S.C. 6101 note).

☐ (6) [Reserved].

https://www.usda.gov/about-usda/general-information/staff-offices/departmental-administration/office-contracting-and-procurement-ocp/usda-far-class-deviations https://www.acquisition.gov/far/52.203-19#FAR_52_203_19 https://www.acquisition.gov/far/52.204-23#FAR_52_204_23 https://www.acquisition.gov/far/52.204-25#FAR_52_204_25 https://www.acquisition.gov/far/52.209-10#FAR_52_209_10 https://www.acquisition.gov/far/52.232-40#FAR_52_232_40 https://www.govinfo.gov/link/uscode/31/3903 https://www.govinfo.gov/link/uscode/10/3801 https://www.acquisition.gov/far/52.233-3#FAR_52_233_3 http://uscode.house.gov/browse.xhtml;jsessionid=114A3287C7B3359E597506A31FC855B3 https://www.acquisition.gov/far/52.233-4#FAR_52_233_4 http://uscode.house.gov/browse.xhtml;jsessionid=114A3287C7B3359E597506A31FC855B3 https://www.acquisition.gov/far/52.203-6#FAR_52_203_6 http://uscode.house.gov/browse.xhtml;jsessionid=114A3287C7B3359E597506A31FC855B3 https://www.govinfo.gov/link/uscode/10/4655 https://www.acquisition.gov/far/52.203-13#FAR_52_203_13 http://uscode.house.gov/browse.xhtml;jsessionid=114A3287C7B3359E597506A31FC855B3 http://uscode.house.gov/browse.xhtml;jsessionid=114A3287C7B3359E597506A31FC855B3 https://www.acquisition.gov/far/52.203-15#FAR_52_203_15 https://www.acquisition.gov/far/52.203-17#FAR_52_203_17 https://www.govinfo.gov/link/uscode/41/4712 https://www.acquisition.gov/far/3.900#FAR_3_900 https://www.acquisition.gov/far/52.204-10#FAR_52_204_10 http://uscode.house.gov/view.xhtml?req=granuleid:USC-prelim-title31-section6101&num=0&edition=prelim

☐ (7) FAR 52.204-14, Service Contract Reporting Requirements (OCT 2016) (Pub. L. 111-117, section 743 of Div. C).

☐ (8) FAR 52.204-15, Service Contract Reporting Requirements for Indefinite-Delivery

Contracts (OCT 2016) (Pub. L. 111-117, section 743 of Div. C).

☒ (9) FAR 52.204-27, Prohibition on a ByteDance Covered Application (JUN 2023) (Section

102 of Division R of Pub. L. 117-328).

☐ (10) FAR 52.204-28, Federal Acquisition Supply Chain Security Act Orders—Federal Supply

Schedules, Governmentwide Acquisition Contracts, and Multi-Agency Contracts. (Dec 2023) (Pub. L. 115–390, title II)

☒ (11)(i) FAR 52.204-30, Federal Acquisition Supply Chain Security Act Orders—Prohibition

(Dec 2023) (Pub. L. 115–390, title II)

☐ (ii) Alternate I (Dec 2023) of FAR 52.204-30.

☒ (12) FAR 52.209-6, Protecting the Government’s Interest When Subcontracting with

Contractors Debarred, Suspended, or Proposed for Debarment, or Voluntarily Excluded. (JAN 2025) (31 U.S.C. 6101 note).

☐ (13) FAR 52.209-9, Updates of Publicly Available Information Regarding Responsibility

Matters (OCT 2018) (41 U.S.C. 2313).Updates of Publicly Available Information Regarding Responsibility Matters (Oct 2018) (41 U.S.C. 2313).

☐ (14) [Reserved].

☐ (15) FAR 52.219-3, Notice of HUBZone Set-Aside or Sole-Source Award (OCT 2022) (15

U.S.C. 657a).

☐ (16) FAR 52.219-4, Notice of Price Evaluation Preference for HUBZone Small Business

Concerns (OCT 2022) (if the offeror elects to waive the preference, it shall so indicate in its offer) (15 U.S.C. 657a).

☐ (17) [Reserved]

☒ (18) (i) FAR 52.219-6, Notice of Total Small Business Set-Aside (NOV 2020) (15 U.S.C. 644).

☐ (ii) Alternate I (Mar 2020) of FAR 52.219-6.

☐ (19) (i) FAR 52.219-7, Notice of Partial Small Business Set-Aside (NOV 2020) (15 U.S.C.

644).

☐ (ii) Alternate I (Mar 2020) of FAR 52.219-7.

☐ (20) FAR 52.219-8, Utilization of Small Business Concerns (JAN 2025) (15 U.S.C. 637(d)(2) and (3)).

☐ (21) (i) FAR 52.219-9, Small Business Subcontracting Plan (JAN 2025) (15 U.S.C. 637(d)(4)).

☐ (ii) Alternate I (Nov 2016) of FAR 52.219-9.

☐ (iii) Alternate II (Nov 2016) of FAR 52.219-9.

☐ (iv) Alternate III (Jun 2020) of FAR 52.219-9.

☐ (v) Alternate IV (JAN 2025) of FAR 52.219-9.

☐ (22) (i) FAR 52.219-13, Notice of Set-Aside of Orders (MAR 2020) (15 U.S.C. 644(r)).

☐ (ii) Alternate I (MAR 2020) of FAR 52.219-13.

☐ (23) FAR 52.219-14, Limitations on Subcontracting (OCT 2022) (15 U.S.C. 637s).

☐ By the end of the base term of the contract and then by the end of each subsequent option period; or

☐ By the end of the performance period for each order issued under the contract.

☐ (24) FAR 52.219-16, Liquidated Damages—Subcontracting Plan (SEP 2021) (15 U.S.C.

637(d)(4)(F)(i)).

☐ (25) FAR 52.219-27, Notice of Set-Aside for, or Sole-Source Award to, Service-Disabled

Veteran-Owned Small Business (SDVOSB) Concerns Eligible Under the SDVOSB Program (FEB 2024) (15 U.S.C. 657f).

https://www.acquisition.gov/far/52.204-14#FAR_52_204_14 https://www.acquisition.gov/far/52.204-15#FAR_52_204_15 https://www.acquisition.gov/far/52.204-27#FAR_52_204_27 https://www.acquisition.gov/far/52.204-28#FAR_52_204_28 https://www.govinfo.gov/link/plaw/115/public/390 https://www.acquisition.gov/far/52.204-30#FAR_52_204_30 https://www.govinfo.gov/link/plaw/115/public/390 https://www.acquisition.gov/far/52.204-30#FAR_52_204_30 https://www.acquisition.gov/far/52.209-6#FAR_52_209_6 http://uscode.house.gov/view.xhtml?req=granuleid:USC-prelim-title31-section6101&num=0&edition=prelim https://www.acquisition.gov/far/52.209-9#FAR_52_209_9 http://uscode.house.gov/view.xhtml?req=granuleid:USC-prelim-title41-section2313&num=0&edition=prelim https://www.acquisition.gov/far/52.219-3#FAR_52_219_3 http://uscode.house.gov/view.xhtml?req=granuleid:USC-prelim-title15-section637a&num=0&edition=prelim http://uscode.house.gov/view.xhtml?req=granuleid:USC-prelim-title15-section637a&num=0&edition=prelim https://www.acquisition.gov/far/52.219-4#FAR_52_219_4 http://uscode.house.gov/browse.xhtml;jsessionid=114A3287C7B3359E597506A31FC855B3 https://www.acquisition.gov/far/52.219-6#FAR_52_219_6 http://uscode.house.gov/browse.xhtml;jsessionid=114A3287C7B3359E597506A31FC855B3 https://www.acquisition.gov/far/52.219-6#FAR_52_219_6 https://www.acquisition.gov/far/52.219-7#FAR_52_219_7 http://uscode.house.gov/browse.xhtml;jsessionid=114A3287C7B3359E597506A31FC855B3 http://uscode.house.gov/browse.xhtml;jsessionid=114A3287C7B3359E597506A31FC855B3 https://www.acquisition.gov/far/52.219-7#FAR_52_219_7 https://www.acquisition.gov/far/52.219-8#FAR_52_219_8 http://uscode.house.gov/browse.xhtml;jsessionid=114A3287C7B3359E597506A31FC855B3 https://www.acquisition.gov/far/52.219-9#FAR_52_219_9 http://uscode.house.gov/browse.xhtml;jsessionid=114A3287C7B3359E597506A31FC855B3 https://www.acquisition.gov/far/52.219-9#FAR_52_219_9 https://www.acquisition.gov/far/52.219-9#FAR_52_219_9 https://www.acquisition.gov/far/52.219-9#FAR_52_219_9 https://www.acquisition.gov/far/52.219-9#FAR_52_219_9 https://www.acquisition.gov/far/52.219-13#FAR_52_219_13 http://uscode.house.gov/browse.xhtml;jsessionid=114A3287C7B3359E597506A31FC855B3 https://www.acquisition.gov/far/52.219-13#FAR_52_219_13 https://www.acquisition.gov/far/52.219-14#FAR_52_219_14 http://uscode.house.gov/browse.xhtml;jsessionid=114A3287C7B3359E597506A31FC855B3 https://www.acquisition.gov/far/52.219-16#FAR_52_219_16 http://uscode.house.gov/browse.xhtml;jsessionid=114A3287C7B3359E597506A31FC855B3 http://uscode.house.gov/browse.xhtml;jsessionid=114A3287C7B3359E597506A31FC855B3 https://www.acquisition.gov/far/52.219-27#FAR_52_219_27 http://uscode.house.gov/browse.xhtml;jsessionid=114A3287C7B3359E597506A31FC855B3

☒ (26) (i) FAR 52.219-28, Postaward Small Business Program Re-representation (JAN 2025

(15 U.S.C. 632(a)(2)).

☐ (ii) Alternate I (MAR 2020) of FAR 52.219-28.

☐ (27) FAR 52.219-29, Notice of Set-Aside for, or Sole-Source Award to, Economically

Disadvantaged Women-Owned Small Business Concerns (OCT 2022) (15 U.S.C. 637(m)).

☐ (28) FAR 52.219-30, Notice of Set-Aside for, or Sole-Source Award to, Women-Owned Small

Business Concerns Eligible Under the Women-Owned Small Business Program (OCT 2022) (15 U.S.C. 637(m).

☐ (29) FAR 52.219-32, Orders Issued Directly Under Small Business Reserves (MAR 2020)

(15 U.S.C. 644(r)).

☐ (30) FAR 52.219-33, Nonmanufacturer Rule (SEP 2021) (15 U.S.C. 637(a)(17)).

☒ (31) FAR 52.222-3, Convict Labor (JUN 2003) (E.O.11755).

☒ (32) FAR 52.222-19, Child Labor-Cooperation with Authorities and Remedies (JAN 2025)

(E.O. 13126).[

☐ (33) [Reserved]

☐ (34) [Reserved]

☒ (35) (i) FAR 52.222-35, Equal Opportunity for Veterans (JUN 2020) (38 U.S.C. 4212).

☐ (ii) Alternate I (JUL 2014) of FAR 52.222-35.

☒ (36) (i) FAR 52.222-36, Equal Opportunity for Workers with Disabilities (JUN

2020) (29 U.S.C. 793).

☐ (ii) Alternate I (Jul 2014) of FAR 52.222-36.

☒ (37) FAR 52.222-37, Employment Reports on Veterans (JUN 2020) (38 U.S.C. 4212).

☐ (38) FAR 52.222-40, Notification of Employee Rights Under the National Labor Relations

Act (Dec 2010) (E.O. 13496).

☒ (39) (i) FAR 52.222-50, Combating Trafficking in Persons (NOV 2021) (22 U.S.C. chapter 78 and E.O. 13627).

☐ (ii) Alternate I (Mar 2015) of 52.222-50 ( 22 U.S.C. chapter 78 and E.O. 13627).

☐ (40) FAR 52.222-54, Employment Eligibility Verification (JAN 2025) (Executive Order 12989).

(Not applicable to the acquisition of commercially available off-the-shelf items or certain other types of commercial products or commercial services as prescribed in FAR 22.1803.)

☐ (41) (i) FAR 52.223-9, Estimate of Percentage of Recovered Material Content for EPA–

Designated Items (May 2008) (42 U.S.C. 6962(c)(3)(A)(ii)). (Not applicable to the acquisition of commercially available off-the-shelf items.)

☐ (ii) Alternate I (MAY 2008) of FAR 52.223-9 (42 U.S.C. 6962(i)(2)(C)). (Not applicable to the acquisition of commercially available off-the-shelf items.)

☐ (42) FAR 52.223-11, Ozone-Depleting Substances and High Global Warming Potential

Hydrofluorocarbons (MAY 2024) (42 U.S.C. 7671, et seq.).

☐ (43) FAR 52.223-12, Maintenance, Service, Repair, or Disposal of Refrigeration Equipment and Air Conditioners (MAY 2024) (42 U.S.C. 7671, et seq.).

☐ (44) FAR 52.223-20, Aerosols (MAY 2024) (42 U.S.C. 7671, et seq.).

☐ (45) FAR 52.223-21, Foams (MAY 2024) (42 U.S.C. 7671, et seq.).

☒ (46) FAR 52.223-23, Sustainable Products and Services (MAY 2024) (DEVIATION FEB 2025)

(7 U.S.C. 8102, 42 U.S.C. 6962, 42 U.S.C. 8259b, and 42 U.S.C. 7671l).

☐ (47) (i) FAR 52.224-3 Privacy Training (JAN 2017) (5 U.S.C. 552 a).

☐ (ii) Alternate I (Jan 2017) of FAR 52.224-3.

☒ (48) (i) FAR 52.225-1, Buy American-Supplies (OCT 2022) (41 U.S.C. chapter 83).

☐ (ii) Alternate I (Oct 2022) of 52.225-1

☐ (49) (i) FAR 52.225-3, Buy American-Free Trade Agreements-Israeli Trade Act (NOV 2023)

(19 U.S.C. 3301 note, 19 U.S.C. 2112 note, 19 U.S.C. 3805 note, 19 U.S.C. 4001 note, 19 https://www.acquisition.gov/far/52.219-28#FAR_52_219_28 http://uscode.house.gov/browse.xhtml;jsessionid=114A3287C7B3359E597506A31FC855B3 https://www.acquisition.gov/far/52.219-28#FAR_52_219_28 https://www.acquisition.gov/far/52.219-29#FAR_52_219_29 http://uscode.house.gov/browse.xhtml;jsessionid=114A3287C7B3359E597506A31FC855B3 https://www.acquisition.gov/far/52.219-30#FAR_52_219_30 http://uscode.house.gov/browse.xhtml;jsessionid=114A3287C7B3359E597506A31FC855B3 https://www.acquisition.gov/far/52.219-32#FAR_52_219_32 https://www.govinfo.gov/content/pkg/USCODE-2018-title15/html/USCODE-2018-title15-chap14A-sec644.htm https://www.acquisition.gov/far/52.219-33#FAR_52_219_33 https://www.govinfo.gov/content/pkg/USCODE-2018-title15/html/USCODE-2018-title15-chap14A-sec637.htm https://www.acquisition.gov/far/52.222-3#FAR_52_222_3 https://www.acquisition.gov/far/52.222-19#FAR_52_222_19 https://www.federalregister.gov/executive-order/13126 https://www.usda.gov/sites/default/files/documents/far-class-deviation-regarding-new-trade-agreements-thresholds.pdf https://www.acquisition.gov/far/52.222-35#FAR_52_222_35 http://uscode.house.gov/view.xhtml?req=granuleid:USC-prelim-title38-section4212&num=0&edition=prelim https://www.acquisition.gov/far/52.222-35#FAR_52_222_35 https://www.acquisition.gov/far/52.222-36#FAR_52_222_36 http://uscode.house.gov/view.xhtml?req=granuleid:USC-prelim-title29-section793&num=0&edition=prelim https://www.acquisition.gov/far/52.222-36#FAR_52_222_36 https://www.acquisition.gov/far/52.222-37#FAR_52_222_37 http://uscode.house.gov/view.xhtml?req=granuleid:USC-prelim-title38-section4212&num=0&edition=prelim https://www.acquisition.gov/far/52.222-40#FAR_52_222_40 https://www.acquisition.gov/far/52.222-50#FAR_52_222_50 http://uscode.house.gov/browse.xhtml;jsessionid=114A3287C7B3359E597506A31FC855B3 https://www.acquisition.gov/far/52.222-50#FAR_52_222_50 http://uscode.house.gov/browse.xhtml;jsessionid=114A3287C7B3359E597506A31FC855B3 https://www.acquisition.gov/far/52.222-54#FAR_52_222_54 https://www.federalregister.gov/executive-order/12989 https://www.acquisition.gov/far/22.1803#FAR_22_1803 https://www.acquisition.gov/far/52.223-9#FAR_52_223_9 http://uscode.house.gov/browse.xhtml;jsessionid=114A3287C7B3359E597506A31FC855B3 https://www.acquisition.gov/far/52.223-9#FAR_52_223_9 http://uscode.house.gov/browse.xhtml;jsessionid=114A3287C7B3359E597506A31FC855B3 https://www.acquisition.gov/far/52.223-11#FAR_52_223_11 https://www.govinfo.gov/link/uscode/42/7671 https://www.acquisition.gov/far/52.223-12#FAR_52_223_12 https://www.govinfo.gov/link/uscode/42/7671 https://www.acquisition.gov/far/52.223-20#FAR_52_223_20 https://www.govinfo.gov/link/uscode/42/7671 https://www.acquisition.gov/far/52.223-21#FAR_52_223_21 https://www.govinfo.gov/link/uscode/42/7671 https://www.acquisition.gov/far/52.223-23#FAR_52_223_23 https://www.govinfo.gov/link/uscode/7/8102 https://www.govinfo.gov/link/uscode/42/6962 https://www.govinfo.gov/link/uscode/42/8259b https://www.govinfo.gov/link/uscode/42/7671l https://www.acquisition.gov/far/52.224-3#FAR_52_224_3 https://www.acquisition.gov/far/52.224-3#FAR_52_224_3 https://www.acquisition.gov/far/52.225-1#FAR_52_225_1 http://uscode.house.gov/browse.xhtml;jsessionid=114A3287C7B3359E597506A31FC855B3 https://www.acquisition.gov/far/52.225-3#FAR_52_225_3 https://www.govinfo.gov/link/uscode/19/3301 https://www.govinfo.gov/link/uscode/19/2112 https://www.govinfo.gov/link/uscode/19/3805 https://www.govinfo.gov/link/uscode/19/4001

U.S.C. chapter 29 (sections 4501-4732), Public Law 103-182, 108-77, 108-78, 108-286, 108- 302, 109-53, 109-169, 109-283, 110-138, 112-41, 112-42, and 112-43.

☐(ii) Alternate I [Reserved]

☐(iii) Alternate II (JAN 2025) of FAR 52.225-3.

☐(iv) Alternate III (FEB 2024) of FAR 52.225-3.

☐(v) Alternate IV (OCT 2022) of FAR 52.225-3.

☐ (50) FAR 52.225-5, Trade Agreements (NOV 2023) (19 U.S.C. 2501, et seq., 19 U.S.C. 3301 note).

☒ (51) FAR 52.225-13, Restrictions on Certain Foreign Purchases (FEB 2021) (E.O.’s, proclamations, and statutes administered by the Office of Foreign Assets Control of the Department of the Treasury).

☐ (52) FAR 52.225-26, Contractors Performing Private Security Functions Outside the United

States (Oct 2016) (Section 862, as amended, of the National Defense Authorization Act for Fiscal Year 2008; 10 U.S.C. Subtitle A, Part V, Subpart G Note).

☐ (53) FAR 52.226-4, Notice of Disaster or Emergency Area Set-Aside (Nov 2007) (42 U.S.C.

5150).

☐ (54) FAR 52.226-5, Restrictions on Subcontracting Outside Disaster or Emergency Area

(NOV 2007) (42 U.S.C. 5150).

☒ (55) FAR 52.226-8, Encouraging Contractor Policies to Ban Text Messaging While Driving

(MAY 2024) (E.O. 13513).

☐ (56) FAR 52.229-12, Tax on Certain Foreign Procurements (FEB 2021).

☐ (57) FAR 52.232-29, Terms for Financing of Purchases of Commercial Products and

Commercial Services (NOV 2021) (41 U.S.C. 4505, 10 U.S.C. 3805).

☐ (58) FAR 52.232-30, Installment Payments for Commercial Products and Commercial

Services (NOV 2021) (41 U.S.C. 4505, 10 U.S.C. 3805).

☒ (59) FAR 52.232-33, Payment by Electronic Funds Transfer-System for Award Management

(OCT2018) (31 U.S.C. 3332).

☐ (60) FAR 52.232-34, Payment by Electronic Funds Transfer-Other than System for Award

Management (Jul 2013) (31 U.S.C. 3332).

☐ (61) FAR 52.232-36, Payment by Third Party (MAY 2014) (31 U.S.C. 3332).

☐ (62) FAR 52.239-1, Privacy or Security Safeguards (AUG 1996) (5 U.S.C. 552a).

☒ (63) FAR 52.240-1, Prohibition on Unmanned Aircraft Systems Manufactured or Assembled by American Security Drone Act-Covered Foreign Entities (Nov 2024) (Sections 1821-1826, Pub. L. 118-31, 41 U.S.C. 3901 note prec.).

☐ (64) FAR 52.242-5, Payments to Small Business Subcontractors (JAN

2017) (15 U.S.C. 637(d)(13)).

☐ (65) (i) FAR 52.247-64, Preference for Privately Owned U.S.-Flag Commercial Vessels (NOV

2021) (46 U.S.C. 55305 and 10 U.S.C. 2631).

☐ (ii) Alternate I (Apr 2003) of FAR 52.247-64.

☐ (iii) Alternate II (Nov 2021) of FAR 52.247-64.

(c) The Contractor shall comply with the FAR clauses in this paragraph (c), applicable to commercial services, that the Contracting Officer has indicated as being incorporated in this contract by reference to implement provisions of law or Executive orders applicable to acquisitions of commercial products and commercial services:

☐ (1) FAR 52.222-41, Service Contract Labor Standards (AUG 2018) (41 U.S.C. chapter67).

☐ (2) FAR 52.222-42, Statement of Equivalent Rates for Federal Hires (MAY 2014) (29 U.S.C.

206 and 41 U.S.C. chapter 67).

☐ (3) FAR 52.222-43, Fair Labor Standards Act and Service Contract Labor Standards-Price

Adjustment (Multiple Year and Option Contracts) (AUG 2018) (29 U.S.C. 206 and 41 U.S.C. chapter 67).

https://www.acquisition.gov/far/52.225-3#FAR_52_225_3 https://www.acquisition.gov/far/52.225-3#FAR_52_225_3 https://www.acquisition.gov/far/52.225-3#FAR_52_225_3 https://www.acquisition.gov/far/52.225-5#FAR_52_225_5 http://uscode.house.gov/view.xhtml?req=granuleid:USC-prelim-title19-section2501&num=0&edition=prelim http://uscode.house.gov/view.xhtml?req=granuleid:USC-prelim-title19-section3301&num=0&edition=prelim https://www.acquisition.gov/far/52.225-13#FAR_52_225_13 https://www.acquisition.gov/far/52.225-26#FAR_52_225_26 https://www.acquisition.gov/far/52.226-4#FAR_52_226_4 http://uscode.house.gov/browse.xhtml;jsessionid=114A3287C7B3359E597506A31FC855B3 http://uscode.house.gov/browse.xhtml;jsessionid=114A3287C7B3359E597506A31FC855B3 https://www.acquisition.gov/far/52.226-5#FAR_52_226_5 http://uscode.house.gov/browse.xhtml;jsessionid=114A3287C7B3359E597506A31FC855B3 https://www.acquisition.gov/far/52.226-8#FAR_52_226_8 https://www.federalregister.gov/executive-order/13513 https://www.acquisition.gov/far/52.229-12#FAR_52_229_12 https://www.acquisition.gov/far/52.232-29#FAR_52_232_29 http://uscode.house.gov/browse.xhtml;jsessionid=114A3287C7B3359E597506A31FC855B3 https://www.govinfo.gov/link/uscode/10/3805 https://www.acquisition.gov/far/52.232-30#FAR_52_232_30 http://uscode.house.gov/browse.xhtml;jsessionid=114A3287C7B3359E597506A31FC855B3 https://www.govinfo.gov/link/uscode/10/3805 https://www.acquisition.gov/far/52.232-33#FAR_52_232_33 http://uscode.house.gov/view.xhtml?req=granuleid:USC-prelim-title31-section3332&num=0&edition=prelim https://www.acquisition.gov/far/52.232-34#FAR_52_232_34 http://uscode.house.gov/browse.xhtml;jsessionid=114A3287C7B3359E597506A31FC855B3 https://www.acquisition.gov/far/52.232-36#FAR_52_232_36 http://uscode.house.gov/browse.xhtml;jsessionid=114A3287C7B3359E597506A31FC855B3 https://www.acquisition.gov/far/52.239-1#FAR_52_239_1 http://uscode.house.gov/view.xhtml?req=granuleid:USC-prelim-title5-section552a&num=0&edition=prelim https://www.acquisition.gov/far/52.240-1#FAR_52_240_1…