11579763 REV AA.pdf

DISTRIBUTION STATEMENT A:

APPROVED FOR PUBLIC RELEASE; DISTRIBUTION IS UNLIMITED.

APPLICATION REVISION HISTORY

NEXT ASSY USED ON REV DESCRIPTION DATE APPRVD

AA SEE L20K1011

“INTERPRET DRAWING IN ACCORDANCE WITH SPEC: ASME Y14.100-2004 AND ASME Y14.5M-1994”

ORIGINAL DATE (YYYY-MM-DD) U.S. ARMY

ARMAMENT, RESEARCH, DEVELOPMENT AND ENGINEERING CENTER

BENET LABORATORIES

WATERVLIET, NEW YORK 12189-4000

1987-12-24

PREP TTF PROC

CHK AK MTRL TITLE

GENERAL DATA FOR CONTAINTER CONSTRUCTION

WITH LENGTHWISE SKIDS (PLYWOOD SIDES)

ENGINEER

A. KVANCZ

SUBMITTED

A. KVANCZ SIZE CAGE CODE DRAWING NO.

A 19206 11579763 APPROVED

MORGAN D. LONGMATE SCALE: - WEIGHT: - SHEET: 1 OF 4

THE BOX/PALLET MANUFACTURER SHALL BE AFFILIATED WITH A GRADING AGENCY OF THE AMERICAN LUMBER STANDARD COMMITTEE (ALSC) WOOD PACKING PROGRAM. THE LUMBER SHALL BE HEAT TREATED AND ALSC CERTIFIED. THIS CERTIFICATION MUST ACCOMPANY CONTAINER DELIVERY. ALSC HEAT TREATMENT (BUG FREE) CERTIFICATION SHALL BE LEGIBLE AND PLACED IN THE CENTER OF 3 LOCATIONS, BREECH END AND EACH SIDE, 3 INCHES FROM THE BOTTOM OF THE CONTAINER. PLACE "DO NOT PAINT OVER THIS CERTIFICATION" ABOVE EACH BUG FREE CERTIFICATION STAMP. IT SHALL BE THE CONTRACTOR'S RESPONSIBILITY TO REQUEST CLARIFICATION OF

ANY AND ALL CONFLICTS OR DISCREPANCIES FOUND ON THE CONTAINER DRAWING.

1. WOOD SPECIES: SPECIES OF WOOD SHALL CONFORM TO ASTM D6199 GROUPS II OR III. FLOORING SHALL

CONFORM TO GROUP I OR II.

2. MOISTURE CONTENT: WOOD MEMBERS 2 INCH NOMINAL THICKNESS OR LESS SHALL HAVE A MOISTURE

CONTENT BETWEEN 12% AND 19% AT THE TIME OF FABRICATION.

3. NOMINAL LUMBER: "NOM" FOLLOWING DIMENSIONS ON BILL OF MATERIAL. OR IN THESE NOTES INDICATES NOMINAL LUMBER SIZES AS SPECIFIED IN ASTM D6199. ALL OTHER SIZES ON BILL OF MATERIAL ARE ACTUAL

SIZE.

4. WOOD MEMBERS: ALL WOOD MEMBERS SHALL CONFORM TO REQUIREMENTS OF TABLE III, ASTM D6199, AND SHALL BE S4S (SURFACED FOUR SIDES). SURFACED LUMBER IS DEFINED AS LUMBER THAT IS DRESSED BY RUNNING IT THROUGH A PLANING MACHINE TO ATTAIN SMOOTHNESS AND UNIFORMITY OF SIZE (REFERENCE MIL-HDBK-7) ROUGH CUT OR ROUGH SAWN LUMBER SHALL NOT BE PERMITTED, PARA. 4.2 OF ASTM D6199 SHALL NOT APPLY. WOOD SHALL BE COMPLETELY FREE OF BARK, DECAY AND INSECT HOLES (REFERENCE

WOOD DEFECTS MIL-HDBK-7).

5. ENDS: SHALL CONSIST OF TWO THICKNESSES OF LUMBER AND ONE OF PLYWOOD AS SHOWN ON THE DRAWING. LUMBER SHALL BE 6 TO 12 INCHES NOMINAL WIDTH AND SHALL BE POSITIONED CROSS-GRAIN TO EACH OTHER. THE CENTER LUMBER LAYER SHALL HAVE THE GRAIN RUNNING VERTICAL AS SHOWN. NAILING

SHALL BE IN ACCORDANANCE WITH NAILING PATTERN SKETCH.

6. FLOOR: FLOOR MEMBERS SHALL BE 6 TO 12 INCHES NOMINAL WIDTH AND SHALL BE POSITIONED CROSSWISE TO THE SIDES WITH A 3/8 TO 1/2 INCH SPACE BETWEEN FLOOR BOARDS. FLOOR SHALL BE FASTENED TO THE SKIDS IN ACCORDANCE WITH THE NAILING PATTERN SKETCH, USING NAILS, STEEL WIRE, COMMON OR BOX

200317 RSJ

DESIGN ACTIVITY SIZE CAGE CODE DRAWING NO. REV

U.S. ARMY

ARMAMENT, RESEARCH, DEVELOPMENT AND

ENGINEERING CENTER, BENET LABORATORIES

WATERVLIET, NEW YORK 12189-4000

A 1NUW7 11579763 AA

SCALE: - WEIGHT: - SHEET: 2 OF 4

STYLE, HAVING CEMENT COATING.

7. THE NUMBER OF BOARDS, AS REQUIRED, TO FABRICATE THE FLOOR AND ENDS SHALL BE ACCORDING TO THE

APPLICABLE CONSTRUCTION NOTES AND DIMENSIONS IN THE RESPECTIVE BILL OF MATERIAL.

8. RUBBING STRIPS AND SKID SPACER: END OF RUBBING STRIPS SHALL BE BEVELED HALF-DEPTH AT AN ANGLE OF 45 DEGREES. RUBBING STRIPS SHALL BE ATTACHED TO THE SKIDS WITH TWO PARALLEL ROWS OF NAILS STAGGERED AND SPACED 12 INCHES MAXIMUM IN EACH ROW. SPIRAL (SCREW) OR GROOVED ANNULAR (RING) NAILS WITH A GALVANIZED FINISHED SHALL BE USED. SKID TO SKID SPACERS USE THE SAME NAILS AS

RUBBING STRIPS.

9. SUPPORTS: SUPPORTS FABRICATED FROM TWO OR THREE PIECES OF 3/4 INCH PLYWOOD SHALL BE FASTENED TOGETHER WITH 5d AND 6d NAILS RESPECTIVELY. NAILING PATTERN SHALL BE SIMILAR TO THE NAILING PATTERN SKETCH. NAILS SHALL BE STEEL WIRE, CEMENT COATED OR ETCHED, CONFORMING TO ASTM F1667.

10. COVER AND SIDE SPLICES: SCARF SPLICES FABRICATED IN ACCORDANCE WITH U.S. PRODUCT STANDARD PS-1, SHALL BE UTILIZED TO MAKE ONE PIECE PLYWOOD COVER AND SIDES.

11. PLYWOOD: PLYWOOD SHALL CONFORM TO U.S. PRODUCT STANDARD PS-1, EXTERIOR GRADE A-C. SHEET

GRADE MARKING SHALL INCLUDE THE “PS-1” MARKING.

12. PLYWOOD PANELS: SIDES AND ENDS SHALL BE FASTENED WITH STEEL WIRE NAILS, COMMON OR BOX STYLES, WITH BOTH STYLES HAVING AN ANNULAR GROOVED (RING) OR SPIRAL (SCREW) SHANK WITH A ZINC HOT-DIP GALVANIZED FINISH. NAILING PATTERN FOR FASTENING TO FRAME MEMBERS SHALL BE TWO PARALLEL ROWS, 8 TO 10 INCHES APART IN EACH ROW, IN STAGGERED ROWS. NAILS SHALL NOT BE OVERDRIVEN MORE

THAN 3/16 INCH BELOW PLYWOOD, HAND NAIL IF NECESSARY-HAMMER DIMPLES ACCEPTABLE.

13. A FIXTURE SHALL BE DESIGNED, FABRICATED AND USED IN CUTTING THE PLYWOOD SUPPORT DIAMETERS.

14. PLYWOOD THICKNESS: PLYWOOD THICKNESS SPECIFIED AS 3/4 INCH MAY BE EITHER 3/4 ACTUAL OR 23/32

ACTUAL.

15. NAILS (UNLESS OTHERWISE SPECIFIED): NAILS (COMMERICAL) SHALL BE STEEL WIRE, COMMON OR BOX STYLES, BOTH STYLES HAVING CEMENT COATED SPIRAL OR ANNULAR (RING) SHANKS. NAIL SIZES SHALL BE IN

ACCORDANCE WITH ASTM D7478/D7478M.

16. NAILING: NAILS SHALL BE DRIVEN SO THAT NEITHER THE HEAD, POINT, OR THE CLINCHED PORTION PROJECTS ABOVE THE WOOD SURFACE. CLINCHED NAILS SHALL BE CLINCHED NOT LESS THAN 1/4 INCH. NAILS SHALL NOT BE OVERDRIVEN MORE THAN 3/16 INCH. WHEN CLINCHING OF NAILS IS REQUIRED, CLINCH NAILS TO THE

INSIDE OF THE CONTAINER.

17. GALVANIZED 8d NAILS SHALL BE USED TO NAIL THE CORNER PLATE TO THE END. THE PLYWOOD SIDE SHALL

ALSO BE NAILED TO THE INNER LUMBER END PIECE EVERY 3 INCHES (END GRAIN NAILING).

18. AFTER NUTS ARE SECURELY TIGHTENED APPLY THE SAME PRIMER AS SPECIFIED IN NOTE 19 ON ALL EXPOSED

THREADS.

19. PAINTING:

PRIMER COAT; SPRAY PAINT EXTERIOR (INCLUDING BOTTOM AND UPPER EDGES OF SIDES AND ENDS) WITH ONE COAT OF PRIMER COAT. PRIMER IS TO BE WATERBASED WITH 100% ACRYLIC, CONTAINING RUST INHIBITIVE PIGMENTS WHICH ARE LEAD AND CHROMATE FREE. PRIMER SHOULD ADHERE TO FERROUS METAL, GALVANIZED STEEL AND WOOD. DRY TO TOUCH IN 1 HOUR OR LESS AND WITH A VOC OF LESS THAN 250 gms/l.

FINISH COAT; SPRAY PAINT EXTERIOR (INCLUDING BOTTOM AND UPPER EDGES OF SIDES AND ENDS) WITH

DESIGN ACTIVITY SIZE CAGE CODE DRAWING NO. REV

U.S. ARMY

ARMAMENT, RESEARCH, DEVELOPMENT AND

ENGINEERING CENTER, BENET LABORATORIES

WATERVLIET, NEW YORK 12189-4000

A 1NUW7 11579763 AA

SCALE: - WEIGHT: - SHEET: 3 OF 4

ONE COAT OF FINISH COAT. FINISH COAT IS TO BE WATERBASED WITH 100% ACRYLIC, FINISH IS TO BE FLAT (LESS THAN 5% GLOSS), SHOULD DRY TO TOUCH IN 1 HOUR OR LESS AND WITH A VOC OF LESS THA 250gms/l.

COLOR TO MATCH FEDERAL COLOR STANDARD #34088.

PRIMER AND FINISH COAT MUST BE CERTIFIED THAT THEY MEET THE ABOVE LISTED SPECIFICATIONS. SLOTTED ANGLE IRON, CORNER PLATE AND ANGLE END PLATE SHALL BE CLEANED AND OIL FREE PRIOR TO APPLYING

COATINGS. PRIMER SHALL BE APPLIED PRIOR TO ASSEMBLY TO THE CONTAINER.

20. UNTOLERANCED DIMENSIONS SHALL BE TREATED AS REFERENCED DIMENSIONS PROVIDED THAT ALL PARTS

FIT TOGETHER AND FUNCTION IN THE MANNER INTENDED.

21. SPLICING OF NOMINAL LUMBER IN ACCORDANCE WITH MIL-C-104, OR OTHERWISE SPECIFIED ON SPECIFIC

DRAWINGS.

SUGGESTED SOURCE(S) OF SUPPLY FOR PAINT

VENDOR(S) VENDOR ITEM NO.

PASSONNO PAINT

500 BROADWAY, WATERVLIET, NY 12189

PH: 518-273-3822

CAGE: 1AD82

PRIMER COAT: 454-01

FINISH COAT: 748-10-S20-703

COLOR: FALVO GREEN

SHIPPING INSTRUCTIONS

1. WHEN SPECIFIED IN THE BILL OF MATERIAL ALL WRAP PROTECTORS, CHAMBER PLUG ASSEMBLIES, MUZZLE DISCS AND BREECH DISCS, SHALL BE BULK SHIPPED IN THEIR OWN CONTAINER AND IDENTIFIED WITH CONTRACTOR'S NAME, CONTRACT NUMBER,PART NAME AND FEDERIAL ITEM NAME AS INDICATED IN THE TITLE BLOCK OF THE DRAWING, WOOD PRESERVATIVE AND/OR PAINTING IS NOT REQUIRED FOR THESE

ITEMS.

2. COVER SHALL BE TACK NAILED, ONE NAIL AT EACH END AND THREE NAILS MAXIMUM EACH SIDE. NAILS SHALL

BE BENT 90 DEGREES FOR EASY REMOVAL.

3. FEDERAL ITEM NAME (1ST AND 2ND ROWS) AND PART NUMBER (3RD ROW) AS INDICATED IN THE TITLE BLOCK OF THE CONTAINER DRAWING), CONTRACT NUMBER (4TH ROW) CONTRACTOR'S NAME (5TH ROW), PARTIAL SHIPMENT NUMBER, (PARTIAL AS A EXAMPLE) (6TH ROW) SHALL BE STENCILED ON EACH SIDE OF THE CONTAINER IN THE UPPER LEFT CORNER AND ON THE LEFT END IN 1 INCH YELLOW LETTERING PER

COMMERICAL ITEM DESCRIPTION A-A-208.

4. WHEN SIZE OF THE CONTAINER PERMITS, A QUANTITY SHALL BE STEEL STRAPPED TOGETHER FOR EASE OF

HANDLING.

DESIGN ACTIVITY SIZE CAGE CODE DRAWING NO. REV

U.S. ARMY

ARMAMENT, RESEARCH, DEVELOPMENT AND

ENGINEERING CENTER, BENET LABORATORIES

WATERVLIET, NEW YORK 12189-4000

A 1NUW7 11579763 AA

SCALE: - WEIGHT: - SHEET: 4 OF 4

NOMINAL LUMBER

NAILING PATTERN SKETCH