1-RFB 6232 - Two (2) 2025 Honda Accord SE Specs.pdf

Section IV Specification

SPECIFICATION #: 2025 Honda Accord SE

These specifications are not meant to limit the vendor: they are to be guidelines to minimum qualifications. Bids on equipment differing in minor detail from these specifications will be considered. Difference or alternations shall be correctly stated and described in detail by the bidder.

Bidders shall fill in all boxes under the column marked – “Comply or Alternate.” Alternates to the following specifications must be explained in detail. Alternates may be detailed on a separate page and referenced to the appropriate section number. Failure to furnish this information may be cause for rejection of bid.

Answer “Comply or Alternate”

Indicate Proposed Year:

Indicate Proposed Make:

Indicate Proposed Model Year: ________________________________

1.0 POWER TRAIN:

1.1. Engine: 1.5LTurbo

1.2. Transmission: CVT

1.3. FWD

1.4. California Emissions System

2.0 CHASSIS:

2.1. Tires

2.1.1. Size- Front/Rear P225/50R17 94v

2.1.2. 17” wheels

2.2. Power Steering

2.3. Fuel Tank Capacity (gal) – 14.8

3.0 SAFETY:

3.1. Air Bag – Driver / Passenger and side curtain

3.2. 4-Wheel ABS disc brakes

3.3. Power assist brakes

3.4. Traction control

3.5. Back up Camera

4.0 DIMENSIONS:

4.1. Wheelbase (in.) – 111.4

4.2. Length (in) – 195.7

4.3. Height (in) – 57.1

4.4. Width (in) – 73.3

4.5. GVWR – 3,280 LBS

O ffice U se O nly

Specification #:

R

X

D ate:

Bidders shall fill in all boxes under the column marked – “Comply or Alternate.” Alternates to the following specifications must be explained in detail. Alternates may be detailed on a separate page and referenced to the appropriate section number. Failure to furnish this information may be cause for rejection of bid.

5.0 ACCESSORIES: (Factory installed unless otherwise noted.)

5.1. Standard Package

5.2. Air Conditioning

5.3. Tilt Steering

5.4. Cruise control

5.5. Power windows

5.6. (2) Additional Keys (4) total

5.7. Power door locks

5.8. Remote keyless entry

5.9. Factory Alarm

5.10. Power mirrors

5.11. Floor mats – Front/Rear

5.12. Intermittent Wipers

5.13. SYNC Bluetooth

5.14. AM/FM Radio Stereo

5.15. Front License Plate Bracket

5.16. All common items standard & safety equipment offered by the manufacturer for the proposed vehicle.

6.0 EXTERIOR:

6.1. Color – Silver & Black

6.2. Alloy Wheels

7.0 SEATING:

7.1. Number of seat positions: 5

7.2. 10-way power driver’s seat

7.3. Black cloth front bucket seats

7.4. Bench rear seat black cloth

7.5. Color – black cloth interior

7.6. Carpet flooring

Bidders shall fill in all boxes under the column marked – “Comply or Alternate.” Alternates to the following specifications must be explained in detail. Alternates may be detailed on a separate page and referenced to the appropriate section number. Failure to furnish this information may be cause for rejection of bid.

1.0 GENERAL:

1.1. All pre-delivery service and warranties shall be provided.

1.1.1. Describe Warranty:

1.2. Vendor to provide four (4) MASTER sets of vehicle keys.

1.3. Vendor to provide three (3) copies of invoice at time of delivery.

1.4. All vehicles shall be delivered with half a tank of fuel.

1.5. Successful bidder must complete attached attribute sheet.

1.6. Vendor shall provide three (3) each parts and repair manuals specific to the vehicle being provided.

1.7. Vehicle must be equipped with air pollution and exhaust emission control apparatus, meeting current Federal and State of California requirements. Vehicle and accessories shall conform to the California Vehicle code, Department of Transportation and, if applicable, to the Safety Orders of the Division of Industrial Safety and current requirements of OSHA.

1.8. Successful bidder shall send VIN for each vehicle ordered at time of factory order with estimated time of delivery.

1.9. After award, any substitution or deletion not identified in the bid response must be approved in writing by the Fleet Services Manager and GSA Procurement.

1.10. Questions regarding the specifications for this solicitation should be directed to:

Robert Willis

County of Ventura GSA Procurement Services

TEL: (805) 662-6832

robert.willis@venturacounty.gov

Bidders shall fill in all boxes under the column marked – “Comply or Alternate.” Alternates to the following specifications must be explained in detail. Alternates may be detailed on a separate page and referenced to the appropriate section number. Failure to furnish this information may be cause for rejection of bid.

2.0 DELIVERY:

2.1. Vendor shall furnish Dealer’s Report of Sale and/or Manufacturer’s

Statement of Origin at time of delivery to:

Joel Miller County of Ventura

GSA Fleet Services 11201-A1 Riverbank Drive

Ventura, CA 93004

TEL: (805) 672-2045

Joel.Miller@ventura.org

2.2. Fill out application for registration of new vehicle per sample attached (Last page of spec).

Call 24 hours in advance to schedule delivery

VENDOR WILL LICENSE/REGISTER VEHICLE

mailto:Joel.Miller@ventura.org