01C SOW_FAA CBTT Mini Drill.pdf

FEDERAL AVIATION ADMINISTRAION (FAA)

STATEMENT OF WORK (SOW)

Rock Drill Equipment Buy

June 12, 2023

1. SCOPE

The Federal Aviation Administration (FAA) requires the design and assemble of one (1) Mini Drill to be used for drilling purposes and geotechnical sampling. The contractor shall design, procure, and assemble all equipment, materials, and supplies contained in Section 2.4 of this SOW, along with all relevant equipment warranties. Additionally, a user training and relevant manuals and maintenance guides should be provided with purchase.

2. TASKS

2.1. DESIGN AND ASSEMBLE

The contractor shall design the appropriate Drilling solution to meet FAA’s requirement. Once completed and approved, the contractor shall procure all necessary equipment requirements for Mini Drill assembly. Upon completion the Government will perform a Factory Acceptance Test to be scheduled in tandem with the contractor provided training included with purchase.

2.2. MATERIAL

The Contractor shall deliver one (1) Mini Drill with all relevant equipment requirements, material, and supplies listed in Section 2.4, or its direct equivalent.

2.3. INVENTORY LIST

The Contractor shall provide an initial inventory list of all items, which shall include relevant part numbers and recommended suppliers for third party and consumables, to the COR and Technical POC. The Contractor shall, also, include a copy of the inventory list with the delivered equipment and a copy of the delivered inventory list to the COR.

2.4. REQUIRED EQUIPMENT, MATERIAL, AND SUPPLIES

Table 1: Equipment Buy List

Item Description Quantity Brand Name or Equal

Skid Steer

Skid Steer Track Loader: supplied with standard features: Open Cab and control system. Hydraulic adjustments for cooling and drill attachment operation. Must be equipped with mounting for rear stabilizers/valves. As well as Lift Countour Balance valves for loading holding. Must come with loader arms and bucket. Operating Weight: 12075 lbs; Rated Operating Capacity: 3500 lbs;

Ground Pressure:4.7 PSI; Engine Power 132 hp. Engine Model / Cummins QSF3.8; Gross Power / 132 hp; Emission Controls meet all US EPA tier 4 final standards ;Track width / 20 in; Ground Contact area 2,840 in; High ambient cooling; Water temp gauge; 2-speed transmission;

Hydrostatic track drive; Loader bucket with bolt on cutting edge;

Hydraulic quick attach; Engine block heater; 25 GPM low hydraulic flow; 45 GPM high flow hydraulic system (4,000 PSI); Push button hydraulic relief valve for quick attach; Normal Charge 12 VDC; ROPS Meets ISO 3471:2008, ISO6682:2005; FOPS Meets ISO3449-2005 level 1 , SAE J386:2006-2; 2 Forward / 2 Rear Halogen Adjustable lights; Horn / Backup alarm; Supplied with forks attachment

ASV RT135 Compact Track Loader

Item Description Quantity Brand Name or Equal

Hydraulic Drilling Attachment

HCMH 550 Skid Steer Static Mount, Locks In Place; 2' Feed Extend; PCFH Hydraulic Chain Feed With Patented Feed System And 8' Steel Changes;

Emergency Stop Pull Cord; HCH10 Hydraulic Clamp, 2"(52mm) - 10.5"(267mm);TE56920 Air/Hydraulic Control Section Includes Hosing; Rear Stabilizers; Side Swivel Mounting Plate; Bit Grease; Grease Gun And Grease

TEI Rock Drill

HCMH550

Hydraulic Rotary Top Drive Drilling Package

Rotary Top Drive 5000 Ft/Lb Of Continuous Torque, Two Speed Capability (Requires 40gpm/152lpm @ 3000psi/207bar)

TEI Rock Drill

Rotary Top Drive

RDS550

Hollow Stem Auger Tooling Package

Hollow Stem Auger Tooling with additional hardware: Drive Cap, 1- 5/8 (41mm) Hex; Drive Cap, 2" (51mm) Hex; Rod Bolt; Hex Nut;

Lockbolt 2 Req'd (Hard Faced);

Repair Bushing; Handle; Socket;

Adapter: NW Rod to Drive Cap;

Adapter: NWJ Rod to Drive Cap;

Pin Coupling, Heat Treated (Repair Only); Auger Section: 5'0" (1.5m);

Center Rod: 5'0" (1.5m), NW;

Center Rod: 5'0" (1.5m), NWJ; Box Coupling; Plug: 1-5/8" (41mm) Hex to NW Box; Plug: 1-5/8" (41mm) Hex to NWJ Box; Plug Bolt; Pilot Bit Shank, 1-5/8" (41mm) Hex; Pilot Bit; Pilot Bit, 1- 5/8" (41mm) Hex, 3-Wing; Repair Key; Clean Out Tap (For Lockbolt Hole); O-Ring; Adapter Rod-Cap

238 API; 6" STEP BIT

238API Drill Rods 5' Lengths

TEI Tock Drills Auger Package

Casing

Casing Tooling Package with Inner Rod and Drivers to include: Casing D (178x1500); ROTOP RH; Drill Rods D90.T.W.T.6.3 2 3/8” API;

External Draw D 178 ROTOP;

Internal Draw D90 2 3/8” API;

Shoe

TEI Rock Drills Casing Package

Down Hole Hamer Tooling Package

Down Hole Hammer package must include: Patriot 50 DTH Hammer 3 1/2" Reg API Pin with Ql50 Shank Bottom and Ql50 Shank 6" CY Med Drill Bit;

Ql50 Shank T130nd Super Jaws Bit For 6"Od X 5" Id;

Ql50 Shank T130nd Super Jaws Bit For 6"Od X 5" Id

TEI Rock Drills Down Hole Hammer (DTH) Package

Hydraulic Winch One (1) tonne Hydraulic Winch 1 TEI Rock Drills Hydraulic Winch

HCW

Shock Sub System Shock Sub System, 3-1/2 API Box 1 TEI Rock Drills Shock Sub System

RD55199

Hydraulic Breaker System

Hydraulic Breaker , 2.0” (52mm) – 10.5” (267mm) with additional valving and auger inserts

TEI Rock Drill

Hydraulic Breaker

HCH10BW

Remote Operating Controller

Radio and/or Cable Remote Controls 1

TEI Rock Drill

Remote Control

EH56920

Dust Suppression System

Dust Suppression System, 200-350 PSI, 100 Gallon Tank

TEI Rock Drill

Dust Suppression System

DS10851

Air Compressor Cummins F3.8l Tier 4f Diesel Engine;

TRL Mounted Lights; Pintle Hitch, Lifting Bail

Doosan Compressor

HP450-VHP400

3. Warranty

The Contractor shall provide a limited warranty on the elements manufactured by the contractor for 12 months from time of delivery, providing that the claim be submitted within the warranty period. Warranty documentation must be in writing and will include any conditions which may invalidate the warranty and procedures on how the Government can exercise warranty rights.

4. DELIVERABLES AND DELIVERY SCHEDULE

The Contractor shall deliver the equipment within 18 months of award. Upon completion of the training, the Government Points of Contact shall load the equipment for transport to the El Centro, CA area. Equipment and materials shall be free from damage and defects, including but not limited to manufacturer defects and damage as the result of handling and transport by the manufacturer and/or the Contractor.

TABLE 2: SCHEDULE OF DELIVERABLES

Deliverables

Item # Deliverable Referenced

SOW

Section

Due Date

1 Inventory List 2.3 At time of delivery

2 Equipment as detailed in Section 2.4 2.4 18 months calendar after receipt of award

3 User Manual and Maintenance Guides 2.1 Upon receipt of Equipment