Upgrade L-Building Laboratory Controls.

NOTICE OF INTENT TO ISSUE A MODIFICATION TO ORDER/CONTRACT. This is not a request for competitive proposals. The Centers for Disease Control and Prevention (CDC), National Center for Occupational Safety and Health (NIOSH), hereby announces its intent to issue a sole source modification under the purchase order # 75D30118P00999 to Trinity Automated Solutions, Inc., 700 Bursca Drive, Ste. 705, Bridgeville, PA 15017 for additional products and installation due to the site conditions differing from the drawings for purchase order # 75D30118P00999 entitled, "Upgrade L-Building Laboratory Controls."

The NAICS code for this acquisition is 238220 with a size standard of $15,000,000.00.

Trinity Automated Solutions, Inc is the only organization that can provide the work under this ongoing order being installed at NIOSH Morgantown, WV under PO#75D30118P00999.

The purpose of this modification is to include additional work in areas where the building has been changed from the original plans/drawings.

The Contractor shall provide all labor, materials, equipment, engineering, programming, start-up, and supervision to upgrade the existing Phoenix Controls and Johnson Controls equipment in the L-Building laboratories. The upgrade and/or replacement equipment shall include, but is not limited to, new Distech Eclypse controllers, Phoenix Celeris C2 valve upgrade kits, Phoenix Celeris C2 valves with electric actuators, occupancy sensors, fume hood monitors, temperature sensors, 2-way pressure independent reheat valves with Belimo electric actuators, discharge air sensors, power supplies, and transformers.

The following shall be included as part of this modification for labs 4423, 4413, 4321, 4422 and lab common areas on floors 2, 3, and 4.

General work:
1) Design labor to revise areas included in this effort
2) Engineering of Wiring Diagrams, Programming and Start-up.
3) Installation and Wiring including network cabling.

Lab common areas on floors 2, 3, and 4:
1) Demolition of six (6) existing VAV hot water valves and three (3) RAD hot water valves.
2) Supply, install, and wire six (6) new VAV controllers and six (6) new VAV wall sensors.
3) Supply, install, and wire nine (9) new hot water valves and three (3) new RAD wall sensors.

For lab 4423:
1) Demolition and capping of one (1) supply air valve, one (1) exhaust air valve, and associated air diffuser/ductwork.
2) Extend air ductwork from exisiting supply air diffusers to removed supply air valve ductwork.
3) Rescope wiring and piping to the demolished air supply valve and exhaust air valve to Lab 4321.

For lab 4413:
1) Extend air ductwork from exisiting supply air diffusers to removed supply air valve ductwork.
2) Demolition of one (1) exisiting exhaust air diffuser and ductwork.

For lab 4321:
1) Supply, install, and wire one (1) new supply air valve and one (1) new hot water valve (note: the install and wire work is rescoped from 4423).
2) Supply, install, and wire one (1) new lab control panel, power supply, ceiling sensor, and wall sensor.

This project is supported by a Justification for Other than Full and Open Competition (JOFOC), under authority of FAR Parts: 13.106-1(b), 13.501(a), 41 U.S.C. 1903, and 41 U.S.C 3304(a)(1).

All vendors must be registered in the System for Award Management (SAM) at www.sam.gov , prior to an award of a federal contract.

This is not a request for competitive quotations; however, the Government will review any/all product, capabilities, and pricing information submitted prior to the closure of this notice. A determination by the government not to compete this proposed contract based upon responses to this notice is solely within the discretion of the government. Information received will normally be considered solely for the purpose of determining whether to conduct a competitive procurement.
Responsible sources that believe they possess the expertise and capabilities identified above are hereby afforded the opportunity to submit to the Contracting Officer within 15 days from the posting date of this notice, their written capabilities statement and pricing information in the format they choose, not to exceed 10 pages. Please forward product and pricing information to Diane Meeder, Contracting Officer, CDC, OAS, through email at Dmeeder@cdc.gov.

If no affirmative responses are received by the due date, in accordance with FAR Parts 12, 13 and 13.5 an order/contract and/or negotiations will be conducted with Trinity Automated Solutions, Inc., 700 Bursca Drive, Ste. 705, Bridgeville, PA 15017

Any responses should be emailed to Diane Meeder at DMeeder@cdc.gov by March 28, 2019 at 12:00 P.M. ET.

.