Hose assembly, saltwater, and freshwater, oily waste.

The Defense Logistics Agency (DLA) Maritime Norfolk at Norfolk Naval Shipyard (NNSY)

intends to award a Firm Fixed Price (FFP) Single Award Contract as Lowest Price Technically

Acceptable (LPTA) Evaluation Factors for the item listed below. The required item is for

commercial item prepared in accordance with the information in FAR Part 13 and FAR Subpart

12.6, as supplemented with the additional information included in this notice.

The Contract Line Item (CLIN) is as follows:

CLIN 0001   2.5" X 10' HOSE ASSEMBLY, SALTWATER, AND FRESHWATER, OILY WASTE.

QTY: 10 EACH

ORDERING DATA:

2.38" I.D. X 2.88" O.D.

SHALL HAVE A MINIMUM WORKING PRESSURE OF 300 PSI AND A MAXIMUM WORKING PRESSURE OF 400 PSI

SHALL HAVE A BURST PRESSURE OF 1400 PSI

MUST HAVE A MINIMUM BEND RADIUS OF 24"

1.40-1.50 LBS. PER FOOT WITHOUT END FITTINGS

SHALL HAVE A TEMPERATURE RATING OF-40 DEGREES (F) TO 212 DEGREES (F)

MUST BE RESISTANT TO WEATHER, OIL, SOLVENTS, AND MILD ACIDS

HOSES ARE TO BE PROVIDED IN 10 FOOT LENGTHS (+6"/ -6") WITH PLASTIC CLEANLINESS CAPS ON EACH END

SHALL HAVE A SYNTHETIC RUBBER INNER TUBE WITH A TEXTILE INNER BRAID

SHALL HAVE A SINGLE WIRE BRAID FOR REINFORCEMENT

SHALL HAVE AN OUTER TEXTILE BRAID WITH A SYNTHETIC RUBBER COVER.

EACH HOSE ASSY SHALL HAVE THE FOLLOWING FIELD ATTACHABLE FITTINGS ON EACH END: 2-1/2" MALE PIPE (NPT 8 THREADS PER INCH).

FITTINGS SHALL BE RED BRASS ALLOY C84400, C90500, OR C92200 EQUAL OR EQUIVALENT TO AEROQUIP PART NUMBER44-412-40-40B. NOTE: FITTINGS AND HOSES MUST BE FROM THE SAME MANUFACTURER

EACH HOSE ASSY SHALL HAVE THE FOLLOWING ADAPTERS ON EACH END, CONNECTED TO THE HOSE FITTINGS: 2-1/2'' MALE HOSE (NST/NH

7-1/2 THREADS PER INCH) ON ONE END AND 2-1/2" FEMALE HOSE SWIVEL (BALL BEARING) (NST/NH 7-1/2 THREADS PER INCH) ON THE OTHER END. FITTINGS MUST BE RED BRASS ALLOY C84400, C90500 OR C92200. ALL THREADED JOINTS SHALL BE ASSEMBLED USING LOCTITE 562 SERIES SEALANT. TEFLON TAPE OR "PLUMBERS PUTTY"IS NOT AUTHORIZED AND SHALL NOT BE USED.

EACH HOSE ASSEMBLY SHALL HAVE, AT A MINIMUM THE MANUFACTURER’S NAME, CONTRACT NUMBER AND PRESSURE RATING ON LAYLINE IN PERMANENT INK OR MOLDED INTO COVERING

SUPPLIER MUST PROVIDE WRITTEN CERTIFICATION THAT HOSE ASSEMBLIES (HOSE AND FITTING) HAVE BEEN HYDROSTATICALLY TESTED AT 285 PSIG WITH CLEAN, FRESH WATER FOR 30 MINUTES WITH ZERO LEAKS AND/OR BULGES.

A COPY OF THIS CERTIFICATION IS TO BE SENT TO CODE 135, BUILDING 276, AND A COPY IS TO BE SENT TO CODE 532 TO BE FILED WITH CONTRACT.

HOSE SHALL BE EATON AEROQUIP 2651 OR EQUIVALENT.

AT NO COST TO THE GOVERNMENT, NORFOLK NAVAL SHIPYARD RESERVES THE RIGHT TO REQUEST A SAMPLE ASSEMBLY FOR

TESTING AND EVALUATION PURPOSES FROM ANY OR ALL OFFERORS DURING EVALUATION PROCESS.

HOSE MUST BE PALLETIZED

SHELF LIFE UU

The requirement will be solicited as a total small business set aside. The NAICS code applicable to this procurement is 326220, Hose and Flexible Tubing with a size standard of 800 employees. The Product Service Code is 4720. The solicitation document incorporates provisions and clauses in effect through FAC 2024-01 and DFARS Change Notice 04/25/2024.

The anticipated delivery date for this acquisition is 21 June 2024. The solicitation, any documents related to this procurement, and all amendments issued will be in electronic form only. THE SOLICITATION IS NOT YET AVAILABLE.

The solicitation number is SPMYM124Q0163, and it is expected to be available on or about 16AUG 2024 and posted to SAM.gov, https://sam.gov/ Quotes will be due by 12:00 PM EST on 22 AUG 2024. Responses to the solicitation notice shall be emailed to the attention of Curtis Douglas at Curtis.douglas@dla.mil  . Please make sure that the solicitation number

(SPMYM124Q0163) is included in the subject line of any email correspondence. Emails

without subject lines will not be read because of security issues.

Potential offerors are hereby notified that the solicitation and any subsequent amendments will only be available by downloading the documents at www.SAM.gov (Contracting Opportunities). The Government is not responsible for inability of the Offeror's to access solicitation documents posted. Prospective Offeror's should also register at on the interested vendor list under SPMYM122Q0163. No telephone or FAX requests will be accepted, and no hardcopy solicitation/amendment will be mailed or faxed.

All responsible sources may submit a proposal which may be considered by the Government. By submitting a quote, the offeror will be self-certifying that neither the principal corporate officials nor owners are currently suspended, debarred, or otherwise ineligible to receive contracts from any federal agency. Failure to do so may represent grounds for refusing to accept the proposal. By submission of a proposal, the offeror acknowledges the requirement that a prospective awardee must be registered in the System for Award Management (SAM) database prior to award, during performance, and through final payment of any contract resulting from the

solicitation, except for awards to foreign vendors for work to be performed outside the United

States. Lack of registration in the SAM database will make an offeror ineligible for award.

Offerors may obtain information on registration and annual confirmation requirements by calling

1-866-606-8220, or via the Internet at https://www.sam.gov. All questions shall be submitted in

accordance with the solicitation, dates and procedures. Please direct all questions regarding this

requirement to Curtis Douglas at Curtis.douglas@dla.mil