Drum, shipping and storage

This notice is to announce that this NSN will be solicited in the near future. This is not a Soliciation/Request for Proposal. The Soliciation/Request for Proposal will be forth coming and will be available via the DSCC Website address (URL) is http://dibbs.dscccols.com/rfp. The response date referenced above is estimated. Solicitation Issue date is on or about 05/08/09, with the Response date on or around 06/08/09. Note: Copies of this solicitation will only be available via the World Wide Web. Hard copies of this solicitation are not available. All responsible sources may submit an offer/quote, which shall be considered.



PURCHASE REQUEST NUMBER IS #0021188104, NSN: 8110-00-030-7780, DRUM, SHIPPING AND STORAGE. QUANTITY: 13.021. UNIT OF ISSUE: EACH. PURCHASE REQUEST WILL SOLICITED AS A SMALL BUSINESS SET-ASIDE.



Item Description:





DRUM, STEEL, SHIPPING AND STORAGE

I.A.W. 49 CFR 178 SUBPART L AND SUBPART M

CFR SECTION 178 AS APPLIES.

UN 1A2/Y1.5/150

IDENTIFY TO:



MIL-STD-130N, 17 DEC 2007

IDENTIFICATION MARKING OF U.S. MILITARY PROPERTY



RATED (MARKED) CAP. 208 LITERS (55 GAL.) &

MINIMUM OVERALL CONTENT 216.5 LITERS (57.2 GAL.)

MINIMUM HEIGHT WITHOUT COVER 864MM, + OR -

3.18MM (34 IN., + OR - 0.125 IN.). MINIMUM

INSIDE DIA. IS 572MM, + OR - 1.59MM (22.5 IN.,

+ OR - 0.0625 IN.). MINIMUM MATERIAL THICKNESS

OF DRUM IS 1.09MM (0.0428 IN.).

DRUM SHALL BE TESTED I.A.W. UN/POP 1A2/Y1.5/150.

MARKINGS: DRUM SHALL BE MARKED I.A.W. UN RQMTS.

FULL REMOVEABLE HEAD WITH NUT AND BOLT TYPE

LOCKING RING. MINIMUM MATERIAL THICKNESS FOR

LOCKING RING 2.40MM (0.0946 IN.).

MINIMUM MATERIAL THICKNESS OF BOLT IS

15.875MM (0.625 IN.). MINIMUM LENGTH IS

88.9MM (3.500 IN.).

PROTECTIVE COATING: COAT ALL EXTERIOR SURFACES

OF THE DRUM (INCLUDING COMPONENT PARTS), EXCEPT

THE CLOSING BOLT AND GASKET (WHEN SUPPLIED),

WITH A RUST INHIBITING COATING THAT WITHSTANDS

THE SALT SPRAY TEST REQUIREMENTS OF ASTM-B-117

UTILIZING A FIVE PERCENT SALT SOLUTION AT 35

DEGREES C (120 DEGREES F) FOR A MINIMUM EXPOSURE

TIME OF 96 HOURS.

RESULTS OF THE SALT SPRAY TEST SHALL SHOW NO

RUST CREEPAGE, BLISTERING, UNDERCUTTING OR LOSS

OF ADHESION OF THE PAINT BEYOND 1/8 INCH OF THE

SCRIBE MARK. ALL OTHER SURFACES OF THE TEST

SPECIMENS SHALL SHOW NO MORE THAN A TRACE OF

FILM FAILURE, (RUST GRADE 9 OF ASTM-D-610), WITH

NONE LARGER THAN 1MM, (3/64 INCH) IN DIAMETER.

ACCEPTABLE COLORS, IAW FED STD 595, ARE AS

FOLLOWS: NOS. 37038, 37030, 34082, 34083,

34086, 34089, 34092, 34102, 34127.

BOLT & NUT SHALL BE INSTALLED TO THE LOCKING

RING SO THEY WILL NOT BE LOST DURING SHIPMENT.

DRUM SHALL BE FURNISHED FULLY ASSEMBLED.



BERENFIELD CONTAINERS, INC. (9Z473) P/N DFS00001



Shipping Locations:



W62G2T

W1BG DEF DIST DEPOT SAN JOAQUN

25600 S CHRISMAN ROAD

REC WHSE 16B PH 209 839 4307

TRACY CA 95304-5000

US



And



W25G1U

TRANSPORTATION OFFICER

DDSP NEW CUMBERLAND FACILITY

2001 NORMANDY DRIVE DOOR 113 TO 134

NEW CUMBERLAND PA 17070-5002

US