COMBINED SYNOPSIS/SOLICITATION Purchase Scrap Railroad Wheels with Shafts

COMBINED SYNOPSIS/SOLICITATION

Purchase Scrap Railroad Wheels with Shafts

(I)        This is a combined synopsis/solicitation for commercial items prepared in accordance with the format in FAR Subpart 12.6, as supplemented with additional information included in this notice and in accordance with the simplified acquisition procedures authorized in FAR Part 13. This announcement constitutes the only synopsis/solicitation; proposals are being requested and a written solicitation will not be issued.

(II)       This solicitation is issued as a request for quotation (RFQ).  Submit written quotes on RFQ Number PMEL-20-00124

(III)      The solicitation document and incorporated provisions and clauses are those in effect through Federal Acquisition Circular 2019-06.

(IV)     This solicitation is being issued with a total small business Set-aside. The associated NAICS code is 331511 and the PSC code is PSC 9670. 

(V)      This combined solicitation/synopsis is for purchase of the following commercial items:

Quantity of 24 Type B Railroad wheels

 TYPE B--Scrap railroad wheel with axel pressed out. Minimum hole diameter eight and one fourth (8-1/4") inches, with a weight of 840 pounds, +- 30 pounds.

Quantity of 4 scrap railroad wheels with cut shafts as specified below.

Scrap railroad wheel with shaft flame cut or better 42 inches from inside of wheel. Cut should

be level+/- one-half (1/2") inch. Approximate weight is 1200 - 1400 pounds. The maximum

shaft diameter at cut not to exceed seven and one-half (7-1/2") inches. Axel must be flush cut on

bottom to allow wheel to sit flat on a flat surface. Wheel axel shaft shall contain a drilled hole of

one and nine-sixteenths (1-9/16 ") inches diameter through the center of the shaft with the hole

centered+/- one-quarter (1/4") inch, two and one-half

(2-1/2 ") inches below the cut edge of the axel, and parallel to the base to the wheel. The hole

shall allow for insertion of a fourteen (14") inch long, one and one-half (1-1/2") inch diameter

steel rod completely through the shaft. The knuckle on the shaft shall not exceed an outside

diameter of 8".

(VI)     Description of requirements is as follows:

Railroad wheels and shafts as describe above.

(VII)    Date(s) and place(s) of delivery and acceptance 12/27/2019 Shipping will be FOB Destination.

 

(VIII)  Questions must be emailed to the attention of Ben Carlson.  The email address is Ben.Carlson@noaa.gov , 206-526-4321.

THE FOLLOWING PROVISIONS AND ATTACHED CLAUSES APPLY TO THIS ACQUISITION

FAR 52.212-1, Instructions to Offerors -- Commercial Items applies to this acquisition. 

 FAR 52.212-3, Offeror Representations and Certifications – Commercial Items

CAR 1352.201-70 Contracting Officer’s Authority

CAR 1352.209-73 Compliance with the Laws

CAR 1352.209-74 Organizational Conflict of Interest

CAR 1352.233-70 Agency Protests

CAR 1352.233-71 GAO and Court of Federal Claims Protests
CAR 1352.237-71 Security Processing Requirements - Low Risk Contracts
 

COMBINED SYNOPSIS/SOLICITATION

Purchase Scrap Railroad Wheels with Shafts

(I)        This is a combined synopsis/solicitation for commercial items prepared in accordance with the format in FAR Subpart 12.6, as supplemented with additional information included in this notice and in accordance with the simplified acquisition procedures authorized in FAR Part 13. This announcement constitutes the only synopsis/solicitation; proposals are being requested and a written solicitation will not be issued.

(II)       This solicitation is issued as a request for quotation (RFQ).  Submit written quotes on RFQ Number PMEL-20-00124

(III)      The solicitation document and incorporated provisions and clauses are those in effect through Federal Acquisition Circular 2019-06.

(IV)     This solicitation is being issued with a total small business Set-aside. The associated NAICS code is 331511 and the PSC code is PSC 9670. 

(V)      This combined solicitation/synopsis is for purchase of the following commercial items:

Quantity of 24 Type B Railroad wheels

 TYPE B--Scrap railroad wheel with axel pressed out. Minimum hole diameter eight and one fourth (8-1/4") inches, with a weight of 840 pounds, +- 30 pounds.

Quantity of 4 scrap railroad wheels with cut shafts as specified below.

Scrap railroad wheel with shaft flame cut or better 42 inches from inside of wheel. Cut should

be level+/- one-half (1/2") inch. Approximate weight is 1200 - 1400 pounds. The maximum

shaft diameter at cut not to exceed seven and one-half (7-1/2") inches. Axel must be flush cut on

bottom to allow wheel to sit flat on a flat surface. Wheel axel shaft shall contain a drilled hole of

one and nine-sixteenths (1-9/16 ") inches diameter through the center of the shaft with the hole

centered+/- one-quarter (1/4") inch, two and one-half

(2-1/2 ") inches below the cut edge of the axel, and parallel to the base to the wheel. The hole

shall allow for insertion of a fourteen (14") inch long, one and one-half (1-1/2") inch diameter

steel rod completely through the shaft. The knuckle on the shaft shall not exceed an outside

diameter of 8".

(VI)     Description of requirements is as follows:

Railroad wheels and shafts as describe above.

(VII)    Date(s) and place(s) of delivery and acceptance 12/27/2019 Shipping will be FOB Destination.

 

(VIII)  Questions must be emailed to the attention of Ben Carlson.  The email address is Ben.Carlson@noaa.gov , 206-526-4321.

THE FOLLOWING PROVISIONS AND ATTACHED CLAUSES APPLY TO THIS ACQUISITION

FAR 52.212-1, Instructions to Offerors -- Commercial Items applies to this acquisition. 

 FAR 52.212-3, Offeror Representations and Certifications – Commercial Items

CAR 1352.201-70 Contracting Officer’s Authority

CAR 1352.209-73 Compliance with the Laws

CAR 1352.209-74 Organizational Conflict of Interest

CAR 1352.233-70 Agency Protests

CAR 1352.233-71 GAO and Court of Federal Claims Protests
CAR 1352.237-71 Security Processing Requirements - Low Risk Contracts