CNC Lathe - Nakamura-Tome WT300MMY-F014
Closed Pre-Solicitation Posted
- Solicitation number
- W519TC25QLTHE
- Agency
-
ACC Rock Island
Army Contracting Command, Department of Defense
- Responses due
- Set-aside
- No set-aside
Opportunity facts
- NAICS code
- 333517 Machine Tool Manufacturing
- PSC
- 3416 Lathes
- Place of performance
- McAlester, Oklahoma 74501, United States
- Points of contact
Notice details come from SAM.gov. Updated .
About this opportunity
The Department of the Army Materiel Command Contracting Command Rock Island Arsenal is issuing a pre-solicitation notice for the procurement of a CNC Turning Center with Live Tooling, specifically the Nakamura-Tome WT300MMY-F014 lathe. This sophisticated manufacturing equipment will be delivered to the Naval Surface Warfare Center Indian Head Division Detachment McAlester at the McAlester Army Ammunition Plant in Oklahoma. The procurement requires a dual-spindle turning center with live tooling capabilities, featuring 25 HP A2-8 spindles on both right and left sides, 4-inch bar capacity, fully closed loop control for X, Y, and Z axes with positioning accuracy of less than 0.0002 inches, and FANUC F32iB CNC controller software. The equipment must fit within an 18-foot by 18-foot maximum area and include comprehensive tooling packages, bar feeder systems, and coolant handling equipment. This pre-solicitation notice was posted on August 4, 2025, with responses due by August 7, 2025, providing potential contractors only three days to submit their proposals.
This procurement does not utilize any set-aside designations and is open to all qualified contractors. The contract requires delivery of the CNC lathe within 12 weeks of award, with complete installation, training, and commissioning to be finished within 20 weeks of contract award, with the contract expected to be awarded by August 31, 2025. The contractor must provide comprehensive services including equipment delivery, installation oversight, startup testing, calibration, verification, performance testing, and on-site orientation training for government personnel. The specification emphasizes the requirement for FANUC brand drives and controls to maintain compatibility with existing programming and minimize training requirements, while WTO live tooling is specified as the preferred brand currently used in the facility. The detailed technical specifications include extensive tooling packages with multiple sets of collets, adapters, holders, and cutting tools, along with specialized equipment such as the LNS TurboChip Conveyor and LNS Quick Load Servo barfeeder systems.
Notice text
LATHE
The only commercially available Turning Center with Live Tooling found to have all the Primary and Secondary Requirements described below combined into one machine is the Nakamura - Tome WT300MMY-F014.
Primary Requirements for the CNC Turning Center with Live Tooling:
- Tools driven by direct drive motors built into the turrets
- 25 HP A2-8 Spindle on both Right and Left
- 4" (102mm) Bar capacity on both spindles
- Fully closed loop control for X, Y & Z axes on both turrets having direct scale (magnetic) feedback.
- Fit within the maximum available area of 18 ft -0 inches x 18 ft - 0 inches
- Positioning accuracy of less than .0002 inch
- Airbag Collision Protection (Nakamura Only)
Secondary Requirements for the CNC Turning Center with Live Tooling:
- Basic Machine
- 2-turret specification (BMT 65)
- Control
- Human Machine Interface (HMI) Operating Terminal with 19. 0" touch control display screen and Power failure Package.
- Fanuc F32iB CNC controller software
- Dual USB Ports
- Maintenance + Alarm Trouble Shooting
- Remote service capability
- Machine data connector
- Production package - high speed canned cycles
- Ethernet
- Screen Text
- Screen display English
- Language on operating system screen: English
- Language on NC Screen: English
- Language on PC Screen: English
- Spindle
- Left Spindle (Main Spindle)
- Through- spindle hole dia. 102 mm
- Bar stock machining capacity dia. 4"
- Maximum spindle speed 2500 rev/ min
- Output 3 0 min continuous 15 /18 kW
- Continuous Torque Rating (133 lb/ft)
- 1 2" Chuck for left spindle (main spindle)
- Left spindle hollow cylinder set for 12-inch hollow chuck for bar diameter 4.0 in.
- Full C- axis (CF- Control)
- C- Axis Clamp Braking Torque (188 lb/ft)
- Left Spindle (Main Spindle)
-
-
- Polar Coordinate Interpolation
- Cylindrical Interpolation
-
- Right Spindle (Sub Spindle)
- Through- spindle hole dia. 102 mm
- Bar stock machining capacity dia. 4"
- Maximum spindle speed 25 00 rev/ min
- Output 3 0 min continuous 1 5 /1 8 kW
- Continuous Torque Rating (133 lb/ft)
- 1 2" Chuck for right spindle (sub spindle)
- Left spindle hollow cylinder set for 12-inch hollow chuck for bar diameter 4. 0 in.
- Full C- axis (CF- Control)
- C- Axis Clamp Braking Torque (18 8 lb/ft)
- Polar Coordinate Interpolation
- Cylindrical Interpolation
- Turrets
- Turret 1:
- 24 station BMT 65
- 12 Station Live Tool
- Servo Drive Index
- Y axis
- Rotating Tool Spindle Speed 3 600 rev/ min
- Rotating tool 5 .5 /3 .7 Kw - 7 . 5 HP
- Turret 2:
- 24 station BMT 65
- 12 Station Live Tool
- Servo Drive Index
- Rotating Tool Spindle Speed 3 600 rev/ min
- Rotating Tool 5 .5 /3 .7 Kw - 7.5 HP
- Turret 1:
- Coolant Supply / Chip Removal
- Water-Soluble coolant
- Chip conveyor (right discharge)
- Filtration Accuracy: 50 um approximately 90%
- Carrying Amount
- Long Chip: 794 L/h
- Short Chip: 13 L/h
- High pressure coolant system for two turret specifications
- Chip Blaster F2-60
- One pump for each turret (24 HP)
- 92. 5 Gallon Tank
- Measuring / Monitoring
- Manual in- machine tool pre- setter (removable type, Left Spindle and Right Spindle)
- Full closed loop control for X axis (turret 1) direct scale feedback, resolution 0. 01 um
- Full closed loop control for X axis (turret 2) direct scale feedback, resolution 0. 01 um
-
- Full closed loop control for Z axis (turret 1 ) direct scale feedback, resolution 0. 01 um
- Full closed loop control for Z axis (turret 2) direct scale feedback, resolution 0. 01 um
- Manual Machine tool pre-setter (Left Spindle side)
- Manual Machine tool pre-setter (Right Spindle side)
- Automation
- Signal lamp 4 colors (red, yellow, green, blue)
- 1/F for exchanging control signals between the machine and peripheral equipment using EtherNet/IP
- Interface for Bar feeder (EtherNet/lP Interface) with terminal block for power supply
- Power Requirements
- 220 volts, 3 phase, 72 KVA
- Control
- High Speed Canned Cycle
- Optional Block Skip (soft key type 2- 9)
- X axis movement direction compliant with ISO standard
- Construction
- Bar feeder
- Spindle Liners 1 pc for 1.00" RS
- Coolant collector extension
- Tools driven by direct drive motors built into the turrets
- Fit within the maximum available areas of 18 ft -0 in x 18 ft -0 in
- Positioning accuracy of less than .0002 inch
- Special Construction
- Bar Feeder
Additional Parts / Products:
LNS TurboChip Conveyor Hinge Belt Type. Right Discharge
LNS Quick Load Servo 105 + BarfeederV ."1/4 to 4-1 /8 "
LNS Quick Load Servo Barfeeder Installation
S teel Spindle Liners for Main Spindle 3 /8 " - 4" 91/4" Increments Qty 13)
S teel Spindle Liners for Second Spindle 3 /8 " - 4" 91/4" Increments Qty 13) Samchully JB-M312 First Spindle
Samchully JB-M312 Second Spindle
High Pressure Coolant both turrets and spindle flush Chip Blaster F2-60
WTO Rotary Tools:
48 -107658 -HP - O. D. Cutting Holder - (4 ea.)
48 -107660 - Combination Tool Holder - (4 ea.)
48 -100204 - Cut-off Holder - (2 ea.)
48 -102279R - Cut-off Holder Right - (2 ea.)
48 -102279l - Cut-off Holder Left - (2 ea.)
420132020 - Straight Drill/Milling Unit, ER32 QF, IC-EC - (4 ea.)
420132019-65 - Straight Drill/Milling Unit, ER32 QF, EC - (4 ea.) 420532026-65 - Face Mill/ Drill Unit, ER32 QF, IC-EC - (4 ea.)
420532025 -65 - Face Mill/ Drill Unit, ER32 QF, EC - (4 ea.)
410120030-65
- Straight Offset Drill/Milling Unit, ER32, EC - (4 ea)
420532043-65
- Right Angle Drill/Milling Unit, Both S ides, ER32 QF, EC - (4 ea)
410120031-65
- Straight Offset Drill/Milling Unit, ER32, IC-EC - (4 ea)
410113002-65
- Straight Offset Drill/Milling Unit, ER20, EC - (4 ea)
410120023-65
- Straight Offset Drill/Milling Unit, ER32, EC - (4 ea)
410113003-65
- Straight Offset Drill/Milling Unit, ER20, IC-EC - (4 ea)
420225014-65
- Right Angle Drill/Milling Unit, ER25, EC - (4 ea)
420525015-65
- Right Angle Drill/Milling Unit, ER25 QF, IC-EC - (4 ea)
420532031-65
- Face Drill/Milling Unit, ER32 QF, EC - (4 ea)
420532032-65
- Face Drill/Milling Unit, ER32 QF, IC-EC - (4 ea)
411010000-65
- Adjustable Angle Drill/Milling Unit, ER1 6, EC - (2 ea)
411010001-65
- Adjustable Angle Drill/Milling Unit, ER1 6, IC-EC - (2 ea)
411007001-65
- Adjustable Angle Drill/Milling Unit, ER1 1, EC - (2 ea)
411007000-65
- Adjustable Angle Drill/Milling Unit, ER1 1, EC - (2 ea)
411500001-65
- Offset Slitting Saw Unit, Type 1 4-2 - (2 ea)
414532003-65
- Broaching Unit, TN765050 - (1 ea)
ReductionSleeve1 -1 /2"(2Sets)
2400150038 - 3 /8 "
2400150050 - 1 /2"
2400150063 - 5 /8 "
2400150075 - 3 /4"
2400150088 - 7/8 "
24001501 00 – 1.0"
24001501 25 - 1-1 /4"
ER11Collets(2Sets)
190011000 - (.276-.020)
ER16Collets(2Sets)
190016000- (. 394 -.020)
ER20Collets(2Sets)
190020000- (.512-.039)
ER25Collets(2Sets)
190025000- (.630-.039)
ER32Collets(2Sets)
190032000- (.787-.079)
ER 11ColletsSealed(2Sets)
191011013 - (.125)
191011019 - (.188)
191011025 - (. 25)
ER 1 6 Collets Sealed (2 Sets)
191016013 - (.125)
191016019 - (. 188)
191016025 - (. 25)
191016031 - (. 313)
191016038 - (.375)
ER 25 Collets Sealed (2 Sets)
191016013 - (. 125)
191016019 - (. 188)
191016025 - (. 25)
191016031 - (. 313)
191016038 - (. 375)
191016044 - (. 438)
191016050 - (. 5)
191016056 - (. 563)
191016063 - (. 625)
ER 32 Collets Sealed (2 Sets)
191032013 - (. 1 25)
191032019 - (. 188)
191032025 - (. 25)
191032031 - (.313)
191032038 - (.375)
191032044 - (.438)
191032050 - (.5)
191032056 - (.563)
191032063 - (.625)
191032075 - (.75)
Interchangeable Milling Arbors (2 Sets)
160015142 - (.625)
160019142 - (.75)
160023142 - (.875)
160025142 - (.1.0)
ER 25 QF Collet Chuck Adapter (2 Sets)
320025010 - (ER16)
320025013 - (ER20)
320025016 - (ER25)
ER 25 QF Collet Chuck Adapter Short (2 Sets)
320025010-07 - (ER16)
320025013-09 - (ER20)
ER 25 QF Collet Chuck Adapter Long (2 Sets)
320025007-40 - (ER11)
320025010-50 - (ER16)
ER 25 QF Weldon/Whistle Notch Shank Adapter (2 Sets)
3201250250 - (. 25)
3201250312 - (.313)
3201250375 - (.375)
3201250500 - (.5)
3201250625 - (.625)
3201250750 - (.75)
ER 25 QF Combination Mill Adapter (2 Sets)
3202250750 - (.075)
3202251000 - (.1.0)
ER 25 QF Blank (5 ea.)
329025000
ER 25 QF Protection Cover (1 0 ea.)
337025000
ER 25 QF Master Gauge (1 ea.)
339125000
ER 32 QF Collet Chuck Adapter (2 Sets)
320032013 - (ER20)
320032016 - (ER25)
320032020 - (ER32)
ER 32 QF Collet Chuck Adapter Short (2 Sets)
320032013 -07 - (ER20)
320032016-07 - (ER25)
ER 32 QF Collet Chuck Adapter Long (2 Sets)
320032007-50 - (ER11)
320032010-60 - (ER16)
ER 32 QF Weldon/Whistle Notch Shank Adapter (2 Sets)
3201320250 - (.25)
3201320312 - (. 313)
3201320375 - (.375)
3201320500 - (.5)
3201320625 - (.625)
3201320750 - (.75)
ER 32 QF Combination Mill Adapter (2 Sets)
3202320750 - (.075)
3202321000 - (1.0)
3202321250 - (1. 25)
ER 32 QF Blank (5 ea.)
329032000
ER 32 QF Protection Cover (10 ea.)
337032000
ER 32 QF Master Gauge (1 ea.)
339132000
One Hand Wrenches/Sets
0067732000 (5 ea.)
0067725001 (5 ea.)
00675000958 (5 ea.)
00675000591 (5 ea.)
00675000515 (5 ea.)
00675000902 (5 ea.)
00675000914 (5 ea.)
00675000448 (5 ea.)
Installation: Contractor shall provide personnel to oversee equipment assembly, installation, startup and test prior to equipment acceptance and commissioning.
Calibration/Setup: Contractor personnel shall perform all calibration, verification and performance testing of the equipment after installation and demonstration of proper operation prior to Government customer providing acceptance.
Training: Contractor shall provide on- site orientation training for this equipment.
NOTES
- FANUC Brand Drives and Control are a must to coincide with current programming and minimize training.
- WTO live Tooling is the current brand we use in the shop.
Files
| File | Type | Posted |
|---|---|---|
| SOW - CNC TURNING CENTER WITH LIVE TOOLING .pdf |
On GovTribe
Work this opportunity
- Track it in your pipeline
- Find teaming partners
- Similar opportunities
- Ask GovTribe AI about this opportunity