WRENCH LOCKING RING FMU-143 CAD.pdf

NO PRIMER OR PAINT

ON THESE SURFACES

3 2X

SEE DETAIL -05

2A4

-10 ASSEMBLY

1.75

5.38

14.77

SEE DETAIL -03

2B3

SEE DETAIL -01

2B7

.13 .25 2X

ISOMETRIC VIEW

SCALE 1 : 2

NOTES:

INTERPRET DRAWING IAW ASME Y14.100 AND ASME Y14.5-2018.1.

REMOVE ALL BURRS AND SHARP EDGES .06 MAX.2.

HEAT TREAT TO 182 KSI TENSIL STRENGTH (ROCKWELL C40), IAW MIL-H-6875.3.

WELDS IAW MIL-STD-2219, CLASS C.4.

PERMANENTLY MARK “18894ASSYX9839066-10” IN APPROX AREA SHOWN, 5

IN .25 HIGH CHARACTERS, IAW MIL-STD-130.

FINISH:6.

PHOSPHATE COATING IAW MIL-DTL-16232, TYPE M OR Z, CLASS 3. EXCEPT

THAT NO COATING WEIGHT IS REQUIRED. COLOR MAY NOT BE UNIFORM

AND MAY FROM LIGHT GREY TO BLACK. DIMENSIONS APPLY BEFORE

APPLICATION OF FINISH.

THE ROTATION LOCATION OF THE HANDLES (FIND NO. 3) IN RESPECT TO THE 7

FINGERS ON THE FITTING (FIN NO.1) IS OPTIONAL.

INSTALL HANDLES SO THAT THEY ARE FLUSH TO .06 BELOW FLUSH WITH 2.725 8

DIAMETER HOLE IN FITTING (FIND NO. 1).

WORKMANSHIP:9.

ALL PARTS SHALL BE IN THE CONDITION SPECIFIED BY THE DRAWINGS AND

SHALL BE FREE FROM DEFECTS SUCH AS, BUT NOT LIMITED TO, BLEMISHES,

BURRS, CAVITIES, PITS, VOIDS, CORROSION, CRACKS, DENTS, DISTORTION,

WARPAGE, GOUGES, SCORES, NICKS, INCLUSIONS, LAPS, POROSITY,

SLIVERS, AND OTHER FOREIGN MATTER. EXCEPT AS PROVIDED ON THE

DRAWING, CLEANING SHALL BE THOROUGH TO REMOVE ALL DIRT, CHIPS,

GREASE, OIL, FLUX CHEMICAL DEPOSITS, RESIDUES, AND OTHER FOREIGN

MATTER. THE CLEANING METHOD AND AGENTS USED SHALL NOT BE

INJURIOUS TO ANY PART OR TO THE ENVIRONMENT, NOR SHALL ANY PART

BE CONTAMINATED BY THE CLEANING AGENT.

REVISIONS

LTR DESCRIPTION DATE APPROVED

REDRAWN WITHOUT CHANGE. FILENAME WAS

F43WR-1-.DRW. 11/08/2004 M. LAPEE

A

IN ZONE C3, 14.86 WAS (14.86). IN ZONE B3, 5.43

WAS (5.43). CHANGED SH2. NOTE 6 WAS GREEN

PAINT. ML 20081203

20081218 EJZ

B

REDRAWN IN SOLIDWORKS WITHOUT CHANGE TO

PARTS. CHANGED .13 EDGE WELD IN ZONE 1C4

FROM 2X TO ALL AROUND. UPDATED NOTES 1,5,6. J.

SKARUPA 20240502

20240515 B.C.

-10 NOMENCLATURE CAGE IDENTIFYING NO MATERIAL / SPECIFICATION ZONE FN

2 HANDLE -05 .50 DIA. STEEL, 4340 IAW MIL-S-5000 AND AMS 6415 1D5 3

1 GUIDE, COLLAR -03 4.00 DIA. STEEL, 4340 IAW MIL-S-5000 AND AMS 6415 1C5 2

1 FITTING -01 4.00 DIA. STEEL, 4340 IAW MIL-S-5000 AND AMS 6415 1B5 1

APPV

AF FORM 2602 IN MMHE, EGLIN AFB

SIGNATURES ARE ON FILE ON

UNLESS OTHERWISE SPECIFIED

U.S. AIR FORCE

PARTS LIST

SHEET

SIZE

TITLE

FRACTIONS ANGLESDECIMALS

.XX±

.XXX±

DR

CHK

ENG

X9839066

CURRENT

CODE IDENT NO.

AF FORM

FEB 74 1655

NEXT ASSEMBLY USED ON

.03

.010 .5°

D

X9839066-10_B

AF FORM 2602 IN MMHE, EGLIN AFB

SIGNATURES ARE ON FILE ON

QUANTITY REQUIRED PER DASH NO.

UNLESS OTHERWISE SPECIFIED

REV

FILENAME:GENERATED USING SOLIDWORKS

U.S. AIR FORCE

APPLICATION

PARTS LIST

SCALE:

DIMENSIONS ARE IN INCHES-TOLERANCES ON:

FRACTIONS ANGLESDECIMALS

.XX±

.XXX±

AIR FORCE AUTHENTICATION AIR FORCE CODE IDENT NO. DRAWING NO.

CURRENT

CODE IDENT NO.

NEXT ASSEMBLY USED ON

ENGINEERING DRAWING LAYOUT D

AIR FORCE RELEASE

MATERIAL:

DISTRIBUTION STATEMENT C DISTRIBUTION AUTHORIZED TO U.S.

GOVERNMENT AGENCIES AND THEIR CONTRACTORS. REASON:

ADMINISTRATIVE OR OPERATIONAL USE. DATE: 02 MAY 2024. OTHER

REQUESTS FOR THIS DOCUMENT SHALL BE REFERRED TO MMHE FOCAL

POINT, EGLIN AFB, FL 32542-5000.

WARNING - THIS DOCUMENT CONTAINS TECHNICAL DATA WHOSE EXPORT

IS RESTRICTED BY THE ARMS EXPORT CONTROL ACT (TITLE 22, U.S.C., SEC.

2751, ET SEQ.). VIOLATIONS OF THESE EXPORT CONTROL LAWS ARE

SUBJECT TO SEVERE CRIMINAL PENALTIES.

DESTRUCTION NOTICE - FOR UNCLASSIFIED, LIMITED DOCUMENTS,

DESTROY BY ANY METHOD THAT WILL PREVENT DISCLOSURE OF CONTENTS

OR RECONSTRUCTION OF THE DOCUMENT.

WRENCH, LOCK RING FMU-143

Z. FIELDING

1:1

98/11/02

98/11/02F.ZABOROWSKI

98/11/05

FINAL FINAL 18894

E. ZAMORSKI

X

B

THIRD ANGLE PROJECTION

CAD MAINTAINED. CHANGES SHALL

ONLY BE INCORPORATED AT THE

DIRECTION OF THE DESIGN ACTIVITY

USING A COMPATIBLE CAD SYSYTEM.

EGLIN A.F.B. FLA A

B B

C C

D D

5 4 3 2 1

OF 21

4.00 (STK) 3.378+

.000 .002

DETAIL -03

1B5

2X R.06

.500

6.00

R.06

DETAIL -05

1D5

.50 (STK)

2X .516+ .008 .001

1.60

2X .325

2X R.06

2X .500

2X 2.000

2.725

2X .100 .000 M A B M

.25

3.375+ .000 .002

2X .100 1.50

2X 2.000

4.00 (STK)

A

B

DETAIL -01

1B5

REVISIONS

LTR DESCRIPTION DATE APPROVED

REDRAWN WITHOUT CHANGE, FILENAME WAS

F43WR-2-.DRW. 11/09/2004 M. LAPEE

A IN DETAIL -01, TOP AND SIDE VIEW SHOWED .516 DIA

HOLE AS SOLID LINES. ML 20081203 20081218 EJZ

B SEE SHEET 1. JDS 20240502 20240515 B.C.

FILENAME:AF FORM

FEB 74 1655 X9839066-10_BENGINEERING DRAWING LAYOUT D

CAD MAINTAINED. CHANGES SHALL

ONLY BE INCORPORATED AT THE

DIRECTION OF THE DESIGN ACTIVITY

USING A COMPATIBLE CAD SYSYTEM.

X

DISTRIBUTION STATEMENT C DISTRIBUTION AUTHORIZED TO U.S.

GOVERNMENT AGENCIES AND THEIR CONTRACTORS. REASON:

ADMINISTRATIVE OR OPERATIONAL USE. DATE: 02 MAY 2024. OTHER

REQUESTS FOR THIS DOCUMENT SHALL BE REFERRED TO MMHE FOCAL

POINT, EGLIN AFB, FL 32542-5000.

WARNING - THIS DOCUMENT CONTAINS TECHNICAL DATA WHOSE EXPORT

IS RESTRICTED BY THE ARMS EXPORT CONTROL ACT (TITLE 22, U.S.C., SEC.

2751, ET SEQ.). VIOLATIONS OF THESE EXPORT CONTROL LAWS ARE

SUBJECT TO SEVERE CRIMINAL PENALTIES.

DESTRUCTION NOTICE - FOR UNCLASSIFIED, LIMITED DOCUMENTS,

DESTROY BY ANY METHOD THAT WILL PREVENT DISCLOSURE OF CONTENTS

OR RECONSTRUCTION OF THE DOCUMENT. 2

18894 1:1

DRAWING NO.AIR FORCE CODE IDENT NO.

SCALE:

REV

OF2

D X9839066 B

SIZE

SHEET

A A

B B

C C

D D

5 4 3 2 1

GENERATED USING SOLIDWORKS