A01_(Rev)_Performance_Work_Statement___Shop_Equipment_PM&R.pdf

Performance Work Statement

APG-ECBC/ADM

Shop Equipment Preventive Maintenance and Repair Service Contract

Rev. March 28, 2017

Background

The Advanced Design & Manufacturing (ADM) Division is tasked to provide the Edgewood Chemical Biological Center (ECBC) and its customers with technical and manufacturing support for unique CB Defense items. ADM provides this support by maintaining a high readiness state with personnel and with a significant complement of design and manufacturing equipment.

Maintenance Requirement

The contractor shall provide onsite at Aberdeen Proving Ground (APG) Edgewood Area unless otherwise authorized, all necessary maintenance, labor (including travel time), documentation, repair parts, maintenance supplies, any and all fluids, tools, test equipment, transportation and other related services at the prices shown in the schedule unless otherwise specified and shall keep the Government-owned equipment in good operating condition per OEM’s standards.

CONTRACT SECURITY CONCERNS:

Contractor and all associated subcontractors employees shall provide all information required for background checks to meet installation access requirements to be accomplished by installation Provost Marshal Office, Director of Emergency Services or Security Office. Contractor workforce must comply with all personal identity verification requirements (FAR clause 52.204-9, Personal Identity Verification of Contractor Personnel) as directed by DoD, HQDA and/or local policy. In addition to the changes otherwise authorized by the changes clause of this contract, should the Force Protection Condition (FPCON) at any individual facility or installation change, the Government may require changes in contractor security matters or processes.

Contractor and all associated subcontractor employees shall comply with adjudication standards and processes using the National Crime Information Center Interstate Identification Index (NCICIll) and Terrorist Screening Database (TSDB) rex.m.valdez Highlight

(Army Directive 2014-05/AR 190-13), applicable installation, facility and area commander installation/facility access and local security policies and procedures (provided by government representative), or, at OCONUS locations, in accordance with status of forces agreements and other theater regulations.

Principal Period of Maintenance

Maintenance shall be performed within the Principal Period of Maintenance (PPM), 7:00AM to 4:00PM, Mondays through Fridays, excluding weekends and Federal holidays.

Preventative Maintenance

Preventive maintenance shall be provided on a quarterly basis to each of the machines listed. This maintenance shall include, but not necessarily be limited to the following as applicable:

Inspect

a. Clean or replace air filters.

Console

a. Check all control panel operations, replace faulty switches and indicator.

b. Clean and inspect tachometer.

c. Inspect relays, clean and/or replace, if required.

d. Follow the calibration procedure recommended by the machine tool manufacture.

e. Clean console of dust, dirt, etc.

Machines

a. Check feedback from resolvers.

b. Check tachometer signal for response on over and under shoot.

c. Check tachometer to determine sticking or binding and adjust.

d. Follow the calibration procedure, as recommended by the manufacturer.

e. Check and clear/replace limit, pressure and/or function switches.

f. Replace or repair any marginal components as required for proper operation.

g. Check oil levels.

h. Lubricate per maintenance manual.

rex.m.valdez Highlight

i. Exchange water-soluble cutting lubricates from reservoirs with new or clean recycled fluid.

j. Correct any minor problem noted by the operator.

k. Pump out and clean both Omax waterjets on a quarterly basis The following items are considered more comprehensive and are performed less frequently than the afore mentioned items:

a. Check, clean or change the hydraulic oil and filter.

b. Check and adjust the hydraulic pressure.

c. Check axis for backlash.

d. Check and lubricated ball screw and bearing.

e. Check spindle bearing.

f. Check and adjust axis Gibbs.

g. Check hydraulic piping for leaks and wear.

h. Check and clean hydraulic oil cooler.

REMEDIAL REPAIR

a. Remedial repair shall be initiated no later than (24) twenty-four hours after notification by the COR that the equipment is inoperative. The contractor shall provide the Contracting Officer's Representative (COR) with a designated point(s) of contact and make arrangements to enable its maintenance representative to receive such notification or provide an answering service or other continuous telephone coverage to permit the COR to make such contact. The contractor shall also provide secondary points of contact in the event that the primary points of contact are not available.

b. Repair service shall include both diagnostic and repair services for all electronic deficiencies, and diagnostic and services of mechanical, pneumatic and hydraulic problems. Service will include utility installation or modification on existing or new equipment.

SPECIALIST OR MANUFACTURERS REPRESENTATIVE SERVICES

a. Should the contractor be unable to determine the cause of equipment failure within 4 working days the contractor shall provide additional assistance from an authorized manufacturer for resolution of the problem.

b. Contractor personnel shall report to the COR or COR designee before and after service work is accomplished.

c. Replacement parts shall be billed against the manufacturer's current list price at time of replacement. All replacement parts must meet the original equipment manufacturer (OEM) specs. Upon the discretion of the COR, replacement parts over $50.00 shall be supported by a copy of the suppliers' invoice and submitted to the COR. Components at list price exceeding $500 shall not be replaced without prior written approval of the COR. The contractor shall prepare and maintain complete maintenance records on all equipment under the contract. The record shall be available for review by the COR during contract performance. The COR shall prepare a service report for each service call. This report shall include as a minimum: date, model and serial number of equipment, description of malfunction, tasks performed, and parts replaced signature of contractor and signature of COR.

A copy of the report shall be provided to the COR after signatures are obtained. A copy of the report shall be provided to the Manufacturing Branch Chief for record keeping of service.

d. Prior to termination or expiration of this contract or removal from this contact of any equipment, the equipment may be subject to an inspection by the Original Equipment Manufacturer (OEM). If the equipment is not in good operating condition upon inspection by the OEM, the contractor agrees to return the equipment to a level suitable for OEM maintenance, (or in accordance with OEM published specifications) or to reimburse the Government for any charges including, but not limited to, travel, parts and labor required to place the equipment in good mechanical, electrical and operating condition as established by the OEM.

e. The above program shall be supplemented as required, to ensure all numerical control units covered here under operate in accordance with the manufacturer published performance specifications.

ON CALL REPAIR OF ADDITIONAL MACHINES

On call repairs for the machines listed shall be on an "as need" basis requested by the (COR). Parts and materials shall be itemized and billed separately against this contract.

Copies of parts, materials and factory repair invoices shall be furnished at time of billing. Machines listed is not all inclusive and is just a sample of the types of machines that could need emergency repair.

CONTRACTOR PERSONNEL

a. All services under this contract are to be performed by competent personnel, experienced and highly qualified to provide required services in accordance with the original equipment manufacturers procedures, without unnecessary delays or interference with Government functions.

b. The contractor shall provide, at a minimum, one (1) Senior Electronic Technician (Class III) and one (1) Electronic Technicians (Class III).

SENIOR ELECTRONIC TECHNICIAN (SET) POSITION DESCRIPTION:

a. The SET exercises direct supervision and control of subordinate contractor employees and sub-contractors involved in the performance of duties related to installation, maintenance and repair of CNC machinery.

Analyzes systems operations and the results of systems tests to ensure proper operation and determine the need for maintenance. The SET ensures provisions of the required services in accordance with the guidance and direction of COR.

b. The SET is responsible for ensuring reliable systems operations, accuracy of data contained in the system, preparation and submission of reports pertinent to systems operations and related topics, and timely submission of reports concerning all unusual activity to the COR.

c. The SET initiates, maintains and certifies the Time and Attendance records of all Electronic Technicians.

d. The SET ensures compliance with rules and regulations regarding conduct and behavior at the work site.

e. The SET will initiate action to ensure proper staffing and apprises the COR of problems or issues likely to present controversy. The SET assigns work and assures its execution. The SET prepares and presents reports and briefings concerning operations of the equipment operations, activities and status, as required. He/she ensures that systems malfunctions are identified, and where possible, corrected and advises the correction. The SET initiates authorized tests of the operation of the equipment and designated components and subsystems to ensure proper operation or to identify the need for maintenance. The SET's work may also significantly affect the design of next generation equipment in so far as his/her analysis disclosed equipment shortcomings or result in the identification of better methodology or operational techniques upon the direction of the COR.

f. The SET serves as a shift supervisor, but is also a working member of the field team.

QUALIFICATIONS OF SENIOR ELECTRONIC TECHNICIAN:

a. The SET shall also meet all the requirements regarding general and specialized experience as well as all educational requirements of the Electronic Technicians as defined.

b. The individual shall possess experience as a technician, instructor, or mechanic (Civilian or Military) which shows progression in the theoretical and practical knowledge of basic electrical and electronic theory, algebra and elementary physics, as well as the ability to use appropriated tools.

ELECTRONIC TECHNICIANS CLASS III POSITION DESCRIPTIONS:

a. The Electronic Technician shall perform installation, maintenance, repair, troubleshooting, testing, operation, or development work in connection with all kinds of electronic equipment in relation to CNC and conventional electronic controlled machinery.

b. The Electronic Technician assists in analyzing equipment operations and the results of equipment tests to ensure proper operation, and assists in determining the need for equipment maintenance and/or repair.

c. This individual provides assistance to security specialists or maintenance personnel involved in the conduct of installation, tests, and/or evaluations of field components.

d. This individual shall comply with all Government rules and regulations regarding conduct and behavior at the work site.

e. Individual shall meet all of the listed qualifications, general, specialized and educational for Electronic Technician Class III as defined.

QUALIFICATIONS OF ELECTRONIC TECHNICIAN(S) CLASS III:

Minimum Experience Requirements for Electronic Technicians Class III:

General experience 2 years: Defined as progressively responsible technical or craft experience in electronics, electricity, engineering, communications, and physics. General experience can also be gained in a similar field that provided technical knowledge and back ground that could be applied in the development, testing, evaluation, design, standardization, research on maintenance, or installation of electronic systems and equipment.

Specialized Experience 4 years: Defined as experience and knowledge in characteristics, functions, operation, and capabilities of a variety of types of electronic equipment. This experience must have included the use of schematic diagrams, a variety of test equipment, and the application of appropriate electronic formulas involved in such duties as testing, trouble shooting, modifying, designing, calibrating, installing, maintaining, repairing, constructing, developing, instructing in electronic equipment, or similar functions.

Also qualifying in experience developing policies, standards, and procedures for maintenance, installation, or similar functions provided the work clearly shows that the applicant applied a specialized knowledge of the theories and principles of a variety of electronics systems or equipment.

Total (General and Specialized) Experience required 6 years.

NOTE: (Experience doing bench repair of television and radio receivers in a commercial shop in which the applicant did troubleshooting on a variety of equipment made by three or more manufacturers and used such special test equipment as sweep generators, marker generator's oscilloscopes, and others normally employed in such servicing is acceptable as specialized experience which is equivalent only to the Class I level and do not meet the requirements of this contract.)

Educational Requirements: Successfully completed education of acceptable type, quality, and duration may be substituted for experience.

Successful completion of Post High School education (at an accredited college, junior college, or technical institute) that included or was supplemented by an average of at least 12 semester hours per year in engineering, physical science, technology, or mathematics which include at least 6 semester hours in electronics may be substituted for experience.

In rating combinations of experience and training, such study may be substituted for general or specialized experience at the rate of 1 academic year for 9 months of experience. Such training/education may not be substituted for more than 6 months of specialized experience.

Equipment List

Shop Equipment List-1 For PM & Repair

FFP- PM

T&M-Repair Sequen ce No.

Equipme nt no.

Equipme nt Name

Manufacturer Model # Serial # Maintenan ce Requireme nt

1 1 Mill Bridgeport 48902 BR 48902 Quarterly

PM

2 2 Mill Bridgeport 67114 BR 67114 Quarterly

PM

3 3 Mill Bridgeport 47812 BR 47812 Quarterly

PM

4 4 Mill Bridgeport 102941 BR 102941

Quarterly

PM

5 5 Mill Bridgeport 75024 BR 75024 Quarterly

PM

6 6 Mill Bridgeport Quarterly

PM

7 7 Mill Bridgeport 108713 BR 108713 Quarterly

PM

8 8 Mill Bridgeport 47817 BR 47817 Quarterly

PM

9 9 Mill Bridgeport 126758 BR 126758 Quarterly

PM

10 10 Mill Bridgeport 12BR BR.256044 Quarterly

PM

11 11 Mill Bridgeport 197124 197124 Quarterly

PM

12 12 Mill Bridgeport Quarterly

PM

13 16 CNC Mill Okuma MC-4VAE 9810 Quarterly

PM

14 17 CNC Mill Toyota FV-45 NF 2330 Quarterly

15 18 Lathe Monarch EE 46390 Quarterly

PM

16 19 Lathe Monarch EE 45472 Quarterly

PM

17 20 Lathe Monarch 13" 35760 Quarterly

PM

18 21 Lathe Monarch Quarterly

PM

19 22 Lathe Monarch 46517 Quarterly

PM

20 23 Lathe American USA-06-07- 012022

Quarterly

PM

21 24 Lathe Lodge & Shipley

311456A 51237 Quarterly

PM

22 25 Lathe Lansing-G 1380 Quarterly

PM

23 26 Lathe Monarch 13" 37765 Quarterly

PM

24 27 Lathe Monarch EE 46391 Quarterly

PM

25 28 Lathe Monarch EE 46808 Quarterly

PM

26 29 Lathe Hardinge Quarterly

PM

27 30 Lathe Hardinge Quarterly

PM

28 31 Lathe Monarch Quarterly

PM

29 32 Lathe Monarch EE 44569 Quarterly

PM

30 33 Lathe Monarch EE 45900 Quarterly

PM

31 34 Lathe Hardinge HLVH 5048K Quarterly

PM

32 35 Lathe Quarterly

PM

33 37 CNC

Lathe

Hardinge SGET-42 SG-234 Quarterly

PM

34 38 Lathe Quarterly

PM

35 44 Band Saw Hyd-Mech V-18APC K0110369 Quarterly

PM

36 46 Surface Grinder

Taft Pierce 3415-17791 Quarterly

37 47 Surface Grinder

Chevalier 3A818 M3927001 Quarterly

PM

38 48 Surface Grinder

Cincinnati G-1-1 1D2T1J-496 Quarterly

PM

39 49 Surface Grinder

Grand Rapids 550 550150 Quarterly

PM

40 50 EDM Agie Chasmilles/CF

MS

07.02.00

CN030 IPG

VP

162 Quarterly

PM

41 51 EDM Agie Chasmilles/CF

MS

382900654 006-003 Quarterly

PM

42 53 Injection Mold

Vandorn 85 85-RS-5F-

HT

409 Quarterly

PM

43 54 Injection Mold

Vandorn 85 85-RS-5F-

WT

410 Quarterly

PM

44 56 Injection Mold

Milacron EV50 6.04 V05A01000

Quarterly

PM

45 72 Shear Standard AS375-10 F210-1810 Quarterly

PM

46 73 Shear Cincinatti 42785 Quarterly

PM

47 80 Grainer Butfering Steelmaster

SPW 213 RT 418260062 Quarterly

PM

48 93 Mill Bridgeport 12.88 BR.256022 Quarterly

PM

49 94 Mill Lagun FTW-25 28983 Quarterly

PM

50 97 Lathe Monarch EE 39801 Quarterly

PM

51 98 Lathe Monarch EE 42899 Quarterly

PM

52 110 Hi Press Pump (S)

OMAX P4060V P152163 Quarterly

PM

53 111 Chiller Unit (S)

Koolant Kooler HAF2000NF -L

33204 Quarterly

PM

54 112 Filter System

EBBCO CLS-141-3A J-9177 Quarterly

PM

55 113 Chiller Unit (N)

Koolant Kooler HAF2000NF -L

33913 Quarterly

PM

56 114 Hi Press Pump (N)

OMAX P4060V P152159 Quarterly

PM

57 115 WaterJet (120X)

OMAX 120X L511517 Quarterly

PM

58 116 Filter System

EBBCO CLS-141-3A J-9177 Quarterly

59 117 Chiller Unit

Koolant Kooler HAF2000NF -L

32509 Quarterly

PM

60 118 Hi Press Pump

OMAX P4055V P722934 Quarterly

PM

61 119 WaterJet (60120)

OMAX 60120 H511654 Quarterly

PM

62 123 Filter Timesavers WDC-7 SN32727 Quarterly

PM

63 124 Grainer Timesavers 113720 32767 Quarterly

PM

64 125 Filter Donaldson Torit

DFT4

(Strippit)

3624099-1 Quarterly

PM

65 126 Laser Strippit LVD SiriusPlus

34108 Quarterly

PM

66 127 N2 Evaporat or

Concoa 641 Series Quarterly

PM

67 128 Skid Ntron 2400-99.99-

Quarterly

Shop Equipment List-2 Repair Only (T&M)

Sequen ce No.

Equipme nt no.

Equipmen t Name

Manufactur er

Model # Serial # Maintenan ce Requireme nt

1 13 CNC Mill HAAS VF-8/40 1076526 Repair as needed (T&M)

2 14 CNC Mill HAAS VF-2 1868 Repair as needed (T&M)

3 15 CNC Mill HAAS VF-2BYT 1061300 Repair as needed (T&M)

4 29 Lathe SW/Trak TRL 1440P 27871 Repair as needed (T&M)

5 36 CNC Lathe HAAS SL-30LB 3083154 Repair as

(T&M)

6 39 Band Saw Do All 36-W 31-571722 Repair as needed (T&M)

7 40 Band Saw Do All HSW-50 238-66351 Repair as needed (T&M)

8 41 Band Saw Do All 1612-3 152-62373 Repair as needed (T&M)

9 42 Saw Do All C-916A 473-89217 Repair as needed (T&M)

10 43 Band Saw WF Wells F-15 A-1795 831893

Repair as needed (T&M)

11 45 Saw Repair as needed (T&M)

12 52 Radial Arm Drill Press

Cincinatti Bickford

3E1423 Repair as needed (T&M)

13 53A Portable Chiller

Advantage S-925-21C1 10009 Repair as needed (T&M)

14 54A Portable Chiller

Advantage S-925-21C1 10010 Repair as needed (T&M)

15 55 Injection Mold

Engle ES1300/300 3561-300-89 Repair as needed (T&M)

16 55A Portable Chiller

Advantage Repair as needed (T&M)

17 56A Portable Chiller

Advantage Repair as needed (T&M)

18 57 Spot Welder

Sciaky PMC04STM 5987R Repair as needed (T&M)

19 58A Chiller Unit

Repair as

20 59 Press Brake

TrumpF TrumaBend V200

887548 Repair as needed (T&M)

21 60 Press Brake

Cincinatti #307 Repair as needed (T&M)

22 61 Press Brake

TrumpF TruBend

B0503A035

Repair as needed (T&M)

23 62 Press Brake Tooling Rack

Kardex Remstar

Shuuttle-XP- 250- 1250K873-

US

10002367 /

Repair as needed (T&M)

24 63 Band Saw Do All DBW-8 631797 Repair as needed (T&M)

25 65 Bender Richards Multi-Form 661 44HB Repair as needed (T&M)

26 66 Bender Richards Multi-Form 173 35 Repair as needed (T&M)

27 67 Spot Welder

Miller Repair as needed (T&M)

28 68 Spot Welder

Miller Dynasty 700 LJ3501776 Repair as needed (T&M)

29 69 Spot Welder

Miller Syncrowave

Repair as needed (T&M)

30 70 Radial Arm Drill Press

Do All DTR-28 78-8203 Repair as needed (T&M)

31 71 Ironworker Repair as needed (T&M)

32 75 Drill Press American Hole Wizard APG: 3413- 17769

Repair as needed (T&M)

33 76 Hydraulic Punch

Hydracrop HYD-70 1137 Repair as needed (T&M)

34 77 Punch Press

W A Whitney

630 630.000.684

Repair as

35 78 Punch Press

Haeger HP6-C 2012 Repair as needed (T&M)

36 79 Strippit Strippit, IDEX,Inc

1250H / 30 2031121395 Repair as needed (T&M)

37 81 Band Saw Oliver 217-D 204579 Repair as needed (T&M)

38 82 Circular Saw

Oliver 136 38507 Repair as needed (T&M)

39 83 Saw Sawstop CB 53230 7329086 Repair as needed (T&M)

40 84 Saw Delta Repair as needed (T&M)

41 85 Band Saw Oliver 116-DL 78902 Repair as needed (T&M)

42 86 Router Elkstrom- Carlson

434 434-582 Repair as needed (T&M)

43 87 Planer Oliver 261-AD 99526 Repair as needed (T&M)

44 88 Planer Oliver 166-ED 97733 Repair as needed (T&M)

45 89 Vacuum Former

Lamco SS1P2X2- 51060-897

Repair as needed (T&M)

46 90 Sander Bridgewood BWBS-25 89032908 Repair as needed (T&M)

47 91 Sander Root/Wyson g

309 DSS1-113 Repair as needed (T&M)

48 92 Sander Bridgewood BW512TS 3095 Repair as needed (T&M)

49 96 Lathe SW/Trak TRL 1440P 27873 Repair as

50 99 Drill Press Swind/Fosdi ck

USG 06-07-

001788

Repair as needed (T&M)

51 100 Dust Collection

Repair as needed (T&M)

52 101 Planer Delta/Rockw ell

37-315 I 333374 Repair as needed (T&M)

53 102 Radial Arm Saw

DeWALT 3571 81160061 Repair as needed (T&M)

54 103 / X-

Lathe SW/Trak TRL 1745P 32347 Repair as needed (T&M)

55 104 Corner Shear

Amada CSW-250 25001847 Repair as needed (T&M)

56 106 / X-

Metal Rolls

Waldemar 403-7-6 61049-09 Repair as needed (T&M)

57 108 Punch Press

E.W. Bliss 20 C USN 90988- 331448

Repair as needed (T&M)

58 109 Punch Press

Niagara A 2-1/4 36517 Repair as needed (T&M)

59 120 / X-

Metal Rolls

Roper Witney Pexto

3416G 190-9-82 Repair as needed (T&M)

60 121 / X-

Metal Rolls

Montgomery 4825 90002 Repair as needed (T&M)

61 122 Pressure Blower

New York Blower

2210 STL 2014-08990-

Repair as needed (T&M)

62 129 Compresso r

Hycomp 2AN10D- B201-

BEMVA-

20/15T

120946-503 Repair as needed (T&M)

63 130 Compresso r

Kaeser SFC 45 T 2084 Repair as needed (T&M)

64 131 / X-

Laser QC Virtek LPG-1EA 14110062 Repair as

65 132 CNC Lathe HAAS ST-20SSY 3098791 Repair as

(T&M)

66 133 Hydraulic Press

Denison Hydroilics

0A75C92DJI

C.

17555 Repair as needed (T&M)

67 134 Compresso r

Ingersoll- Rand

SSR UP6-25-

PX2258U32

Repair as needed (T&M)

68 135 CNC Mill HAAS OM-2A 1894495 Repair as needed (T&M)

69 136 Arbor Press

Greenerd No. 5 3444/H52/60

Repair as needed (T&M)

70 137 / X-

Injection Molder

Mini-Jector 552 120995598 Repair as needed (T&M)

71 138 Oven Tenney Repair as needed (T&M)

72 139 Sander / Grinder

Rockwell Model 7 Grinder

3415-00- M01-1617

Repair as needed (T&M)

73 140 Chiller Unit

Koolant Kooler

HCV15000P

R-NF-FILT

3C043 Repair as needed (T&M)

74 141 Vacuum Sealer

Audion Vac VM 151H 1519041712 Repair as needed (T&M)

75 X-3 Mold Injector

Mini-Jector Repair as needed (T&M)

76 X-4 Sandblaste r

Zero Cabinets (Clemco)

BNP600P

900R&DC

55473 Repair as needed (T&M)

77 X-5 Charging Station

Power Factor

1PF18B-

600EMP

Repair as needed (T&M)

78 X-6 Sheet Roller (blue)

Waldemar 403-7-6 Repair as needed (T&M)

79 X-7 Sheet Roller (Sm Grn )

Roper Whitney

34166 Repair as

80 X-8 Sheet Roller (Lrg Grn )

Montgomery 4825 Repair as needed (T&M)

81 X-9 Lockforme r

Repair as needed (T&M)

82 X-10 Polisher Cincinatti SPL Repair as needed (T&M)

83 X-11 Portable Mini-Saw

Delta UniSaw

86E08333 Repair as needed (T&M)

84 X-12 Vertical Belt Sander

Porter - Cable

Repair as needed (T&M)

85 X-13 Oven Trent Repair as needed (T&M)

86 X-14 Parts Washer

Better Engineering

F-3000-PZX Repair as needed (T&M)

87 X-15 Tumbler / Deburr

Aimco OR-10V Repair as needed (T&M)

88 X-16 Inspection Scanner

Virtek LPSIEA Repair as needed (T&M)

89 RM50 EOSINT

M270

EOS/Integra SI-1088 Repair as needed (T&M)

90 RM50 Sinterstatio n 2500plus

EOS/Integra G0121740 Repair as needed (T&M)

91 Vanguard

HS

(upgraded)

Repair as needed (T&M)

92 RM50 SLA Viper si

RP Support America /Integra

03FB0235 Repair as needed (T&M)

93 RM50 SLA 7000 RP Support America /Integra

01EC0143 Repair as needed (T&M)

94 RM50 SLA 3500 RP Support America /Integra

98BA0019 Repair as

95 RM49 OBJET

Connex

Stratasys 50070 Repair as needed (T&M)

96 RM49 FDM

Fortus 900

Stratasys L0042 Repair as needed (T&M)

97 RM49 FDM

Fortus 400

Stratasys T2911 Repair as