01. Amed02_Salient Characteristic_Revised.docx

“Amendment 02” Common requirement:

- All Solid wood material for these product’s moisture content ratio shall be lesser(under) than 12%.

- Item #1-5 shall be custom made. Therefore, when TEB is held the contractor shall present the sample furniture for item #1-5 as specified in salient characteristic without finish so that customer can examine the samples and evaluate the wood material and other component based on salient characteristic. However, these pictured samples shall be the same as the product and shall be without finish as shown photos below.

1.Dining Table W/one extension kit - 200EA Dining Table with extension kit- Rounded Edges Model &Manufacturer: Custom made.

Color: TBD, determined by the customer after award Dimensions Overall Unextended: W60-64X D40-44” X H30” (+/- 0.75” variable is acceptable) Leaf (Additional Panel): W14-18” X D 40-44”X H1”(Thickness) Overall Width of extension space up to 14-20” Top thickness:1” Apron: 3 ea on each side, 2 ea on extension panel, thickness: 0.78”, H 3” Specification Feature Tabletop& leg material: North America oak solid wood, 1” top thickness Apron: H 3” Ply wood Floor clearance under top: 29" Seating Capacity: 4-6 Seating Capacity When Fully Extended: 6-8 Construction: Mortise and tendon joints Doweled and corner blocked for maximum stability.

Reinforced top and apron with Z-clip and wood block: One end screw firmly onto the tabletop, while the other fits a saw kerf along the table apron. Make slots on apron for z-clips to fit in.

For reinforcing the top, Attach 2 furring strips to both sides (1 left, 1 right at the bottom of the top plate (same direction as the slide).

Slot on outside of apron surface (image is below) Adhesive: Eco-friendly wood adhesive Designed for disassembly and assembly/knockdown style.

Leg locking mechanism to main body is nut lock mechanism.

Warranty: 1 year Packing : Cardboard box / Must be packed separately between main body and extension leaf

Table Top Assembly Parts:

· Standard Dining Table Extension Slides (wood slide)- 63*25*815mm

· 6Heavy duty leaf leveler- Heavy duty leaf levelers mount to the underside of tabletops to keep components aligned. Used with table pins for secure fit (mount on cutting side of top).

· 4 set Align-n-lock-mount to the underside of table tops and leaf.

· Z-Clips(table top fasteners), wood block, corner blocks, screws, wood pins, T-shape edge block(2ea on edge of apron(center) 2 ea on edge of extension panel)

Table leg

· Solid Oak Wood

· Decorative carving legs:4 curvy legs are carved equally by carving machine without pattern unlike shown above attached photo. No required the pattern.

· Mount Hanger bolt shall be embedded into the leg so it can be jointed to the corner block.

2. Coffee Table Type - 100 EA Coffee Table Coffee table -Either Rounded Edges and Oval shape or square shape or equals to.

Model &Manufacturer: Custom made.

Color: TBD, determined by the customer after award Dimensions W 42-46” X D 26-28” X H 18” (+/- 0.75” variable is acceptable) Top thickness: 0.86” Distance between aprons to aprons: 28.7” *16.2” Leg: H 17.5” Apron: 4 ea, W 25” * H 3” (center) ~3.4 (side)”thickness 0.78”

Specification Feature Tabletop& leg material: North America Oak solid wood (No MDF/HPM) Tabletop edge profile: Dupont edge Construction: Mortise and tendon joints Doweled and corner blocked for maximum stability.

Wood joints (screws): Pocket hole joinery for high tensile strength (drill oblique holes) Adhesive: Eco-friendly wood adhesive Parts: wood block, screws, wood pins, L-bracket Apron Silhouettes: Arched Cutout For reinforcing the top, make groove under the tabletop plate and put 3 furring strip upright Leg locking mechanism to main body is bolt lock mechanism.

Warranty: 1 year Packing: Cardboard box

Special Requirement:

This Furniture requires to be manufactured as same as FMB have in warehouse.

Table leg

· Solid oak Wood

· 4 Curvy legs

· Top of leg-wood block 1.8” *1.8”(each corners);refer the image

3. Dining chair with arms – 200 EA

Dining chair with arms – rounded Edges Model & Manufacturer : Custom made Main body Color : TBD, by the customer after award Dimensions Frame : W 21-26 “ X D 19-23” X H 40” (+/- 0.5” variable is acceptable) Frame thickness : 1” at a minumum Back panel thickness: 0.5” at a minimum with one designed carved line on outer side.

Seat Height :17” from the ground Seat size : W20(longest)” & W 15.5(Shortest)” X D 16.5” Specification Feature Material: North America Oak-Solid wood (No MDF/HPM) Arms: Two curvy arms fixed two different points with screws on main body frame (Photo attached) / Two-hole covers shall be affixed.

Construction: Mortise and tendon joints using glue and hardwood reinforcing cleats and screws.

Doweled and corner blocked for maximum stability connected with three embedded lines on main body frame. (Photo attached)

Seat material and cushion and design: Minimum 1” thickness of 25KG/m3 density Poly Urethan foam covered on plywood board thickness of 0.62”. Must have one seam following the edge of seat.

Floor protector: Must have plastic floor protector on its each corner.

Fabric: Flame-resistant & Water-Proof polyester (Equal’s to MFR: Boryung textile / MO : charcoal-2021) / Fabric Color : Gray FABRIC will be Government Furnished Item (GFM). Once awarded Government POC will provide the required Fabric.

Warranty: 1 year Packing: Cardboard box Special Requirement:

Front legs should be attached to main body with nut lock mechanism and back side leg should be attached with bolt lock mechanisim.

4. Dining chair without arms – 500 EA

Dining chair with arms – rounded Edges Model & Manufacturer : Custome made Main body Color : TBD, by the customer after award Dimensions Frame : W 20-21 “ X D 19-23” X H 40” (+/- 0.5” variable is acceptable) Frame thickness : 1” at a minumum Back panel thickness: 0.5” at a minimum with one designed carved line on outer side.

Seat Height :17” from the ground Seat size: W20(longest)” & W 15.5(Shortest)” X D 16.5” Specification Feature Material: North America Oak-Solid wood (No MDF/HPM) Construction: Mortise and tendon joints using glue and hardwood reinforcing cleats and screws.

Doweled and corner blocked for maximum stability connected with three embedded lines on main body frame. (Photo attached)

Seat material and cushion and design: Minimum 1” thickness of 25KG/m3 density Poly Urethan foam covered on plywood board thickness of 0.62”. Must have one seam following the edge of seat.

Floor protector: Must have plastic floor protector on its each corners.

Fabric: Flame-resistant & Water-Proof polyester (Equal’s to MFR: Boryung textile / MO : charcoal-2021) / Fabric Color : Gray FABRIC will be Government Furnished Item (GFM). Once awarded Government POC will provide the required Fabric.

Warranty: 1 year Packing: Cardboard box Special Requirement:

Front legs should be attached to main body with nut lock mechanism and back side leg should be attached with bolt lock mechanisim.

5. Chair for the desk - 200 EA

Chair for the desk – sled base Model & Manufacturer : Custome made Main body Color : TBD, by the customer after award Dimensions Frame : W 18-18 5/8“ X D 18” X H 31 5/8-32” (+/- 0.5” variable is acceptable) Frame thickness : W 1” X D 2.25” at a minumum.

Back panel thickness : 1” at a minimum Seat Height :17 3/4” from the ground Seat size : W16” X D 19” X H 2.5” Back size : W16 ¾” X D 2.5” X H 6” Specification Feature Material: North America Oak-Solid wood (No MDF/HPM) Construction: Mortise and tendon joints using glue and hardwood reinforcing cleats and screws.

Doweled and corner blocked for maximum stability with pocket hole joinery on every connecting parts.

Seat material and cushion and design : Minimum 0.1” thickness of 25KG/m3 density Poly Urethan foam covered on plywood board thickness of 0.5”. Not required to have seam on its’ edge.

Back material and cushion and design: Minimum 0.62” thickness of 25KG/m3 density Poly Urethan foam covered fully surrounding on bent plywood board thickness of 0.8~0.9”. Not required to have seam on its’ edge.

Floor protector: Must have plastic floor protector on its each corners.

Fabric: Flame-resistant & Water-Proof polyester (Equal’s to MFR: Boryung textile / MO : charcoal-2021) / Fabric Color : Gray FABRIC will be Government Furnished Item (GFM). Once awarded Government POC will provide the required Fabric.

Warranty: 1 year Packing: Cardboard box Special Requirement:

This Furniture requires to be manufactured as same as FMB have in warehouse.

image5.jpeg image6.jpeg image7.jpeg image8.jpeg image9.jpeg image10.jpeg image11.jpeg image12.jpg image13.jpeg image14.jpeg image15.jpeg image16.jpeg image17.jpeg image18.jpeg image19.jpeg image20.jpeg image21.jpeg image22.jpeg image23.jpeg image24.jpeg image25.jpeg image26.jpeg image27.jpeg image28.jpeg image29.jpeg image30.jpeg image31.jpeg image32.jpeg image33.jpeg image34.jpeg image35.jpeg image36.jpeg image37.jpeg image38.jpeg image39.jpeg image40.jpeg image41.jpeg image42.jpeg image43.jpeg image44.jpeg image45.jpeg image1.jpg image2.jpg image3.png image4.jpeg