W912BV20Q0002.pdf

SEE ADDENDUM

(No Collect Calls)

W912BV20Q0002 05-Nov-2019

b. TELEPHONE NUMBER

918.669.4978

8. OFFER DUE DATE/LOCAL TIME

02:00 PM 05 Dec 2019

5. SOLICITATION NUMBER 6. SOLICITATION ISSUE DATE

AUTHORIZED FOR LOCAL REPRODUCTION

PREVIOUS EDITION IS NOT USABLE

STANDARD FORM 1449 (REV. 2/2012)

Prescribed by GSA – FAR (48 CFR) 53.212

(TYPE OR PRINT)

(SIGNATURE OF CONTRACTING OFFICER)

ADDENDA ARE

26. TOTAL AWARD AMOUNT (For Gov t. Use Only )

23.

CODE 10. THIS ACQUISITION IS

SUCH ADDRESS IN OFFER

17b. CHECK IF REMITTANCE IS DIFFERENT AND PUT

BELOW IS CHECKED

TELEPHONE NO.

W912BV9. ISSUED BY

18b. SUBMIT INVOICES TO ADDRESS SHOWN IN BLOCK 18a. UNLESS BLOCK

7. FOR SOLICITATION

INFORMATION CALL:

a. NAME

ANGELIA V GUYNN

2. CONTRACT NO. 3. AWARD/EFFECTIVE DATE 4. ORDER NUMBER

(TYPE OR PRINT)

30b. NAME AND TITLE OF SIGNER 30c. DATE SIGNED 31b. NAME OF CONTRACTING OFFICER

30a. SIGNATURE OF OFFEROR/CONTRACTOR 31a.UNITED STATES OF AMERICA

0 27a. SOLICITATION INCORPORATES BY REFERENCE FAR 52.212-1. 52.212-4. FAR 52.212-3. 52.212-5 ARE ATTACHED.

25. ACCOUNTING AND APPROPRIATION DATA

1. REQUISITION NUMBER

20.

ADDITIONAL SHEETS SUBJECT TO THE TERMS AND CONDITIONS SPECIFIED.

OFFEROR TO COMPLETE BLOCKS 12, 17, 23, 24, AND 30

SOLICITATION/CONTRACT/ORDER FOR COMMERCIAL ITEMS

ARE NOT ATTACHED

27b. CONTRACT/PURCHASE ORDER INCORPORATES BY REFERENCE FAR 52.212-4. FAR 52.212-5 IS ATTACHED. ADDENDA ARE ARE NOT ATTACHED

(BLOCK 5), INCLUDING ANY ADDITIONS OR CHANGES WHICH ARE

SET FORTH HEREIN, IS ACCEPTED AS TO ITEMS:

. YOUR OFFER ON SOLICITATION

28. CONTRACTOR IS REQUIRED TO SIGN THIS DOCUMENT AND RETURN

% FOR:SET ASIDE:UNRESTRICTED ORX

SMALL BUSINESS

17a.CONTRACTOR/ CODE FACILITY

OFFEROR CODE

CONTRACTING DIV

US ARMY CORPS OF ENGINEERS, TULSA DISTRICT

2488 E. 81ST STREET

TULSA OK 74137-4290

18a. PAYMENT WILL BE MADE BY CODE

RATED ORDER UNDER

DPAS (15 CFR 700)

13a. THIS CONTRACT IS A

13b. RATING

CODE15. DELIVER TO CODE 16. ADMINISTERED BY

SEE SCHEDULE

12. DISCOUNT TERMS11. DELIVERY FOR FOB DESTINA-

TION UNLESS BLOCK IS

MARKED

SEE SCHEDULE

14. METHOD OF SOLICITATION

RFQ IFB RFPX

918-669-7436FAX:

TEL: SERVICE-DISABLED

VETERAN-OWNED

SMALL BUSINESS

8(A)

HUBZONE SMALL

BUSINESS

SIZE STANDARD:

1,500

NAICS:

336120

X

OFFER DATED

29. AWARD OF CONTRACT: REF.

DELIVER ALL ITEMS SET FORTH OR OTHERWISE IDENTIFIED ABOVE AND ON ANY

COPIES TO ISSUING OFFICE. CONTRACTOR AGREES TO FURNISH AND

EMAIL:

TEL:

31c. DATE SIGNED

SEE SCHEDULE

SCHEDULE OF SUPPLIES/ SERVICESITEM NO. QUANTITY UNIT UNIT PRICE AMOUNT

24.22.21.19.

WOMEN-OWNED SMALL BUSINESS (WOSB)

ELIGIBLE UNDER THE WOMEN-OWNED

SMALL BUSINESS PROGRAM

EDWOSB

32g. E-MAIL OF AUTHORIZED GOVERNMENT REPRESENTATIVE

SOLICITATION/CONTRACT/ORDER FOR COMMERCIAL ITEMS

(CONTINUED)

PAGE 2 OF55

ACCEPTED, AND CONFORMS TO THE CONTRACT, EXCEPT AS NOTED: ______________________________________________________

32a. QUANTITY IN COLUMN 21 HAS BEEN

RECEIVED INSPECTED

32b. SIGNATURE OF AUTHORIZED GOVERNMENT

REPRESENTATIVE

32c. DATE 32d. PRINTED NAME AND TITLE OF AUTHORIZED GOVERNMENT

REPRESENTATIVE

32e. MAILING ADDRESS OF AUTHORIZED GOVERNMENT REPRESENTATIVE 32f . TELEPHONE NUMBER OF AUTHORIZED GOVERNMENT REPRESENTATIVE

37. CHECK NUMBER

FINALPARTIALCOMPLETE

36. PAYMENT35. AMOUNT VERIFIED

CORRECT FOR

34. VOUCHER NUMBER

FINAL

33. SHIP NUMBER

PARTIAL

38. S/R ACCOUNT NUMBER 39. S/R VOUCHER NUMBER 40. PAID BY

41a. I CERTIFY THIS ACCOUNT IS CORRECT AND PROPER FOR PAYMENT

41b. SIGNATURE AND TITLE OF CERTIFYING OFFICER 41c. DATE

42a. RECEIVED BY (Print)

42b. RECEIVED AT (Location)

42c. DATE REC'D (YY/MM/DD) 42d. TOTAL CONTAINERS

STANDARD FORM 1449 (REV. 2/2012) BACK

Prescribed by GSA – FAR (48 CFR) 53.212

AUTHORIZED FOR LOCAL REPRODUCTION

PREVIOUS EDITION IS NOT USABLE

SEE SCHEDULE

20.

SCHEDULE OF SUPPLIES/ SERVICES

21.

QUANTITY UNIT

22. 23.

UNIT PRICE

24.

AMOUNT

19.

ITEM NO.

W912BV20Q0002

Section A - Solicitation/Contract Form

INSTRUCTION TO OFFERORS

Instructions to Offers

Read the solicitation in its entirety and all amendments before submitting documents. Payments will be made after receipt of a proper invoice and receipt of acceptable supplies or services. Regular office hours: Monday to Friday, 8:00 a.m. to 4:30 p.m. CST

MAIL, FAX, EMAIL or HAND DELIVER YOUR DOCUMENTS

Do not include excess information, to include audio-visual materials, electronic media, CD’s, thumb drives, etc. or pages of the solicitation that do not contain information provided by the perspective offeror. NO cross outs or strike through marks. Submit a legible quote with no correction marks.

EMAIL

Emailed quotes in a file format readable by Adobe or Microsoft Office readable file formats are the only acceptable methods of submitting a quote electronically. All documents must be attached in one file. Reference the solicitation in the subject line. Send quotes to E-mail address copy a. Ensure your quote is received before the due date and time. In order for your quote to be considered responsive, all required materials must be received before the due date and time. If all required materials are not received your quote will not be considered.

FAX or MAIL

Include a cover sheet that references the Contract Specialist – Angelia V. Guynn and the solicitation number. When submitting through mail ensure you clearly mark the envelope to:

TULSA DISTRICT CORPS OF ENGINEERS

Angelia V. Guynn, CECT-SWT-E 2488 E. 81ST Street

TULSA, OK 74128-4609

FAX: (918) 669-7495

Clearly mark the envelope in the lower left hand corner with the solicitation number. All pages should be numbered. Use only 8 ½ by 11 inch paper for fax or mail submissions. Do not use fold-outs (e.g., 11” x 14” or 11” x 17” sheets). Do not use a font size smaller than 10, or condensed print for any submission. Time New Roman or Arial Font are the only acceptable fonts. All page margins must be at least 1 inch wide, but may include headers and footers. Illegible handwritten quotes will not be considered. Typed quotes are highly encouraged and the preferred method. Do not use spring clamps, staples, or exceed the recommended capacity of the fastener or binder.

Do not use plastic multi-hole/spiral binding systems, heat binding systems, or other systems which do not facilitate the ready insertion of additional pages or removal of pages. DO NOT use tabbed dividers, flagged tabs, or any divider that extends beyond the paper size to separate sections. The pages must be able to be removed from their binding without ripping or tearing. Ensure to allow enough time to submit your quote before the due date and time.

HAND DELIVER

If your submission will be hand-carried, please provide notification to the Contract Specialist at least one working day in advance (918-669-4978) or Angelia.v.guynn@usace.army.mil , as unescorted visitors are not allowed in the Contracting Division offices. Please consider in your arrival that visitors must go through security check points.

Offerors can only submit their documents to the Contract Specialist or a Contracting Officer of the Tulsa District Office. The address of the Tulsa District Office is below:

TULSA DISTRICT CORPS OF ENGINEERS

2488 E. 81st Street

TULSA, OK 74137-4290

This procurement is being conducted in accordance with Simplified Acquisition Procedures (SAP) of FAR Parts 12 and 13. Any reference to offers or bids or offerors or bidders should be substituted with quotations or quoters. All reference to discussions shall not be interpreted under FAR Part 15, but rather indicate that the Government may communicate with offerors/quoters as allowed under simplified acquisition procedures.

Submit the following documents:

1) A signed copy of the 1st page of the solicitation and all amendments

2) Complete the past performance references page, if included in solicitation.

3) Complete the Excel pricing schedule provided in the solicitation (all cells except for the unit prices are locked).

4) Complete all FAR Clauses with applicable blanks filled in from SECTIONS I, K, L, and M

INQUIRIES – OFFEROR’S QUESTIONS AND COMMENTS

USE OF BIDDER’S INQUIRY

Prospective offerors shall submit questions and inquiries related to this solicitation in accordance with the following (no other means of questions or inquiries will be answered except through Bidder Inquiry):

a. For information related to amendments, and the dates set for receipt of proposals, please check http://www.fedbizopps.gov

b. Contractual and Technical inquiries and questions relating to proposal procedures are to be submitted via Bidder Inquiry in ProjNet at https://www.projnet.org/projnet.

1. To submit and review bid inquiry items, offerors will need to be a current registered user or self-register into the system. To self-register go to the aforementioned web page and click on the BID tab. Select Bidder Inquiry, select agency USACE, and enter the Bidder Inquiry Key for this solicitation listed below, your e-mail address, and then click login. Fill in all required information and click create user. Verify that information on next screen is correct and click continue.

2. From this page you may view all bidder inquiries or add an inquiry.

3. Bidders will receive an acknowledgement of their question via e-mail, followed by an answer to their question after it has been processed.

4. The Solicitation Number: W912BV20Q002 The Bidder Inquiry Key is: ZPWG7V-23XQB2

c. The Bidder Inquiry System will be unavailable for new inquiries until 29 Nov 2019 in order to ensure adequate time is allotted to form an appropriate response and amend the solicitation, if necessary.

d. Offerors are requested to review the specification in its entirety, and review the Bidder Inquiry System for answers to questions prior to submission of a new inquiry.

e. The call center operates weekdays from 8AM to 5PM U.S. Central Time Zone (Chicago). The telephone number for the Call Center is 800-428-HELP.

f. Offers will NOT be publicly opened. Information concerning the status of the evaluation and/or award will NOT be available after receipt of proposals.

g. The point of contact for this solicitation is:

Contract Specialist: Angelia V. Guynn Telephone: (918) 669-4978 E-MAIL: Angelia.v.guynn@usace.army.mil

Section B - Supplies or Services and Prices

PRICE SCHEDULE

PROPOSAL SCHEDULE

SNOOPER TRUCK ACQUISITION

Item Unit No. Description Quantity Unit Price Amount

BASE PROPOSAL

001. Snooper Truck, Fully Assembly 1 EACH $_____ $_____

002. Operation and Maintenance Training 1 EACH $_____ $_____

OPTION 1

003. Auxiliary Diesel Engine 1 EACH $_____ $_____

TOTAL BASE BID $_________

OPTION 1 BID $_________

TOTAL PROPOSAL $_________

PROPOSAL SCHEDULE NOTES

1. All costs for items of work that are not listed separately in the Proposal Schedule or specifically mentioned to be included in a particular item price shall be included in the listed item price most closely associated with the work involved.

2. This solicitation requires submission of a proposal on all items. Failure to do so will result in the proposal being rejected without further consideration.

3. Only one contract for the entire schedule will be awarded under this solicitation.

4. Item 002 “Operation and Maintenance Training” to occur after delivery and acceptance of Item

001 “Snooper Truck, Fully Assembled”

Section C - Descriptions and Specifications

SPECIFICSTIONS

Underbridge Inspection Vehicle with Inspection Boom/Bucket

The following shall indicate minimum requirements, including all components, accessories and safety features considered standard, necessary to make a complete operating unit, whether identified herein or not.

1. General Provisions:

1.1 It is the intent and purpose of these specifications to describe a vehicle to provide underbridge inspection by making it possible to position three (3) workmen and their tools approximately 53' horizontally under a bridge, extend approximately 44' above and extended down approximately 57’ below the bridge surface to perform inspection of areas under the bridge as directed in the performance section of these specifications.

With the work bucket completely extended, the truck can be driven slowly forward or backward to provide continuous or overlapping areas of coverage. The vehicle must operate within 102” of the traffic lane so that lane closures are kept to a minimum.

1.2 The vehicle shall be an underbridge inspection vehicle and will include a truck chassis, flatbed body, aerial device, and any necessary equipment, components, accessories or options required to furnish a complete unit ready for operation. The aerial unit shall be truck-mounted, hydraulic-powered with four (4) articulating boom sections, a telescoping section, two rotation turrets, and a maneuverable three-man, 600 pound capacity aluminum platform with fully proportional controls. The construction and stability of the completed unit shall conform to all current ANSI 92.8 regulations.

2. Performance:

2.1 The underbridge inspection vehicle shall be capable of placing the inspector(s) in positions above, under and outside of the bridge described in these specifications and in a manner such that the inspector can make physical contact with areas as indicated.

2.2 It shall be the bidder’s responsibility to meet all specifications and performance requirements mentioned herein for the underbridge inspection vehicle. The unit shall be a current model, designed to operate without using outriggers and have been in production for at least 3 years. The bidder shall submit a brochure of the proposed device with dimensions and clearances with his bid proposal.

3. Pre-Delivery Service:

3.1 Truck and auxiliary engines will be checked and filled to the proper oil level.

3.2 Transmission will be checked and filled to proper oil level.

3.3 Hydraulic system oil reservoir will be checked and filled to proper oil level.

3.4 Cooling system will be checked and filled to the proper level and will contain proper antifreeze to test -40 F.

4. Chassis: New - Current Model

4.1 GVWR: 80,000 pounds, minimum.

4.2 Wheelbase: 285”, approximate, Confirm Cab to rear axle (CA) dimension with manufacturer.

4.3 Frame: The minimum acceptable frame side rail shall meet or exceed the required section modules of 35 cubic inches minimum, with 110,000 psi steel and a Resistance to Bending Moment (RBM) of 3,850,000 inch pounds minimum. Section modules, RBM, frame reinforcement, and chassis shall meet underbridge inspection aerial device manufacturer's minimum requirements.

4.4 Front Axle: The front axle shall be 20,000 pounds, minimum, capacity and have 20,000 pound capacity suspension on each axle with heavy duty shock absorbers.

4.5 Rear Axle: The rear axle shall be heavy duty tandem at 46,000 pound minimum capacity, single speed with power divider, and provided with 46,000 pound capacity Hendrickson RT-460 type suspension, or approved equivalent. Gear ratio shall allow the vehicle to travel between 65-68 mph. Locking differential shall be supplied.

4.6 A 20,000 lb. air operated pusher axle shall be installed approximately 54” in front of the front tandem axle. Exact location to be determined by the Bridge Inspection Unit manufacturer.

4.7 Transmission: The transmission shall be an Allison Model 4000RDS or 4500RDS automatic with PTO provision, or approved equivalent.

4.7 PTO: The power take-off shall be transmission mounted power shift type, cab controlled, and shall have a ratio to provide optimum performance of the hydraulic pump operating upper structure components further described in the specs. Unit shall be equipped with a PTO engaged light.

5. Engine: The engine shall be equipped as recommended by the manufacturer including at least the following:

5.1 The engine shall be a diesel powered unit, minimum of 370 gross HP and 1,350 ft/lbs.

torque. Provide remote PTO throttle control capability for bridge insp. unit. Engine shall be set up with a 2 speed throttle.

5.2 Heavy duty dry type air cleaner.

5.3 Oil filter and fuel filters as recommended by the engine manufacturer but including as a minimum a primary fuel filter between the fuel tank and engine.

5.4 Horizontal muffler with vertical tailpipe and bright shield to protect personnel from burns. The tailpipe’s clearance should be minimal behind the back side of the cab so that it does not interfere with the driver’s view of the Bridge Inspection Unit.

5.5 High temperature protection warning light with gauges for oil pressure and coolant temperature.

5.6 Electric engine block heater, 110 volt, 1500 watt. Receptacle for attaching heater to outside power service shall be mounted on driver side of unit.

5.7 Engine water filter system or extended life coolant, if recommended by engine mfr.

5.8 Engine Brake.

5.9 Premium radiator and heater hoses.

5.10 Heavy duty radiator and coolant system.

5.11 Electrical system shall include a minimum of three (3) 12 volt, 1,875 CCA, maintenance free, or approved equal. Battery box with cover provided. Alternator shall provide a minimum of 130 amp. capacity.

Lights on cab and chassis shall be manufacturer standard. A back-up warning device shall be provided.

6. Cab:

6.1 Cab shall be all steel or aluminum, standard conventional 83 Decibels Acoustic (DBA), with tilting hood.

6.2 Seats and seat belts for driver and one (1) passenger shall be provided, driver’s seat shall be fully adjustable suspension bucket and the passenger seat shall be non-adjustable cushioned bucket seat.

6.3 The following shall be provided as a minimum:

a. Insulated headliner and back panel.

b. Lighter and ash tray.

c. Dual sun visors.

d. Arm rests and door pulls.

e. Windshield washer.

f. 2-speed wipers.

g. Dome light.

h. Cab grab handles, interior or exterior.

i. Two (2) outside , West Coast mirrors, 16"x7", with convex mirrors, both sides.

j. Heater and defroster, heavy duty fresh air type.

k. Fuel tank and steps, Single 100, LH mounted.

l. Power steering.

m. Instrumentation shall include all standards as a minimum.

n. Air conditioning.

o. AM-FM radio.

p. Air horns.

q. Strobe lights mounted in rear bumper and above cab.

p. Body builder wiring

7. Tires:

7.1 Front: 425/65R22.5, 20 ply, mounted on 12.25 steel disc wheels.

Rear: 11R22.5, 14 ply, mounted on 8.25 steel disc wheels.

8. Brake System:

8.1 Brakes shall be air actuated. The air compressor shall have a minimum capacity of 13 Cubic Feet per Minute (CFM), with air dryer with heater and automatic moisture drain. The system shall have a dash mounted warning light for low air pressure, a slack adjuster for each wheel, air pressure gauge dash mounted, air release parking brake.

9. Rust Proofing and Undercoating:

9.1 Rust proofing of the body shall include the following standards as a minimum:

Full undercoating shall be applied in a continuous and uniform coating, from of all under deck body sheet metal except that drive shafts, drain holes, lubrication points, engine crank-case, heavy castings and suspension components shall be kept free of coating material. Chassis shall have standard factory undercoating.

10. Paint:

10.1 Unit shall be painted to manufacturer's standard white, but shall include as a minimum, a rust inhibitive primer and a finish coat. The complete paint film, to include primer and finish coat, shall have a minimum thickness of 2.5 mils.

10.2 The chassis and bridge inspection unit shall be finished with Standard White

11. Safety Equipment:

11.1 One (1) first aid kit.

11.2 One (1) reflective triangle set.

11.3 One (1) Fire Extinguisher.

11.4 TWENTY (20) Orange Traffic Cones.

11.5 Two (2) “ONE LANE ROAD AHEAD”, MUTCD W20-4 (Manual on Uniform Traffic Control Devices). Must be capable of attaching to tripod stand.

11.6 Two (2) Heavy Duty Tripod Stands with flag holders and Orange Flags. Must be NCHRP-350 (National Cooperative Highway Research Program) approved.

12. Manuals:

12.1 Two (2) sets of Operator's, Repair and Parts manuals will be provided for truck and Bridge Inspection Unit. in CD and paper format.

13. Deck Body:

13.1 The body shall be constructed of plate steel. The deck shall be welded to the heavy duty structural steel crossmembers and longitudinals with side and end rails. Deck surface shall be finished with non-skid paint.

13.2 The body shall have two (2) locations with access steps installed on the left and rear of the deck. The steps shall be constructed with heavy duty material. First step shall be approximately 15" to 18" from ground.

13.3 Two (2) under deck tool boxes shall be installed, one on the right side and one on the left side of the body. Boxes shall be constructed of aluminum. Doors shall be downward opening with cable stops and lock. Doors shall have seals for weatherproofing. Drain holes shall be provided. Locks and keys provided.

13.4 The unit shall have four (4) anti-sail flaps, installed in front and back of rear tandem wheels. The flaps shall have road clearance of ten (10) inches when truck is empty.

14. Under Bridge Inspection Unit:

Overall Dimensions:

a. Overall stored length: 40', 0 " (maximum).

b. Overall stored height: 13', 6" (maximum).

c. Overall stored width: 102" (maximum).

All components of the aerial device shall be stored inside the length and width of the flatbed body. When in operation, only 102” of the traffic shall be occupied.

Under Bridge Inspection Aerial Device Components:

The following underbridge inspection aerial device assembly shall consist of the following minimum components:

a. Pedestal and subframe.

b. Two (2) hydraulic rotation turrets.

c. Four (4) hydraulic articulating boom sections, one telescoping section.

d. Three-man aluminum platform.

e. Auxiliary diesel engine and PTO power sources.

f. Hydraulic system.

g. Controls and safety system.

h. Truck stabilizers.

i. Communication system.

j. Accessories.

k. Labels.

14.A. PEDESTAL & SUBFRAME:

Both the pedestal and subframe shall be constructed of high strength steel and shall have sufficient strength to withstand all torsional stress imposed by the boom assemblies with the maximum rated load in the work platform.

The pedestal shall be mounted behind the truck cab. The pedestal shall be welded to a tubular or beam type subframe which shall extend the full length of the chassis frame.

The subframe shall be fastened to the chassis frame with mounting plates and grade 8 bolts.

14.B. ROTATION TURRETS:

Turret No. 1:

The main turret shall be mounted on top of the pedestal and hinged to the main boom (No. 1). It shall rotate the booms off of both sides of the vehicle.

Turret No. 2:

The second turret shall be mounted at the end of Boom No. 1 and hinged to Boom No. 2.

It shall rotate a minimum of 180 when all booms are deployed. The turret shall be controlled automatically by a hydraulic cylinder so as to eliminate leveling arms. It shall also have the capability of being controlled manually to adjust for bridge slopes of up to 5 degrees.

Bearing:

Each turret shall rotate on a heavy-duty shear ball type bearing protected against dirt and moisture, and provided with means for pressure lubrication.

Motor and Gear Box:

Rotation shall be powered by a reversible hydraulic orbital motor driving a gear box, which shall prevent free wheeling in case of hydraulic failure.

Counterweight:

A counterweight shall be attached to the pedestal assembly and shall rotate with the bridge inspection unit on the opposite side, and stay within the width of body when the booms are deployed.

14.C. BOOMS:

The underbridge inspection aerial device shall be equipped with four articulating, hydraulically operated booms. All telescopic boom sections shall be equipped with high wear capacity nylon support rollers or pads.

Boom No. 1:

The main boom, approx. 15’ long, shall be hinged to the mainframe pedestal turret. Sidewalks width clearance shall be 11’ minimum

Boom No. 2:

The second boom shall be attached to the end of Boom No. 1 and provide vertical clearance of 20’ minimum. It shall be capable of articulating to a horizontal position, perpendicular from the bridge so that the inspection bucket can access the bridge fascia.

Boom No. 3:

The third boom shall be telescopic and hinged to the end of Boom No. 2. The third and fourth booms must be capable of reaching a minimum of 46’ horizontally under the bridge when boom no. 2 is in a vertical (90o) position.

Boom No. 4:

Shall be a pivoting end section with an articulating range of 90 degrees above horizontal, and 34 degrees below horizontal. It shall provide a reach of 10’-5” minimum, measured from the top of boom no. 3 to the top of the platform.

Boom Cylinders:

Booms shall have full hydraulic powered cylinders. All cylinders shall be pilot operated, double-acting with integral safety holding valve. Chrome rods shall be provided on all lift cylinders.

Cylinder Swivel Pins:

Cylinder shall be attached to the booms with high strength steel pins. Cylinder pins may be secured with either keeper bolts in the head of the pin or locking nuts. All cylinders to have replaceable bushings.

Overhead Reach:

The platform must be capable of being placed above the bridge deck approximately 44 feet.

14.D. THREE-MAN ALUMINUM PLATFORM:

One (1) 3-man aluminum platform with a minimum 600 lb. capacity shall be hinged at the end of the fourth boom and shall automatically be kept level at all times by a hydraulic leveling system.

Platform dimensions shall be a minimum of 40"x60"x42" deep. An access gate with flip latch shall be provided.

Safety Harnesses & Lanyards:

Three (3) safety harnesses of different sizes and lanyards shall be furnished. Attachments for lanyards shall be installed in the platform.

14.E. AUXILIARY DIESEL ENGINE AND PTO POWER SOURCES:

The primary source of power for operation of the Underbridge Inspection aerial device hydraulic and electric systems shall be provided by a PTO-driven, transmission-mounted hydraulic pump.

As an option to this contract, an auxiliary engine will be supplied. It shall have the capacity to perform more than one unit movement simultaneously. This auxiliary engine shall include the following:

1. 12-volt electrical system with keyed ignition, electric starter, and alternator.

2. Fuel connection to the chassis fuel tank(s).

3. Diesel engine fuel filtration system.

4. Engine compartment cover which allows complete access to engine and hydraulic system components.

14.F. HYDRAULIC SYSTEM:

All movements of the underbridge inspection aerial device shall be made by hydraulic pressure. All hydraulic cylinders shall be double acting with direct coupled safety check valves as protection, in case of pump or hose failure.

Reservoir shall be of steel welded construction with 50 gallon (minimum) storage capacity.

Reservoir shall have baffles and exterior oil sight level gauge.

Hydraulic oil shall be filtered through a return line 10 micron filter with replaceable element. A 100 mesh strainer shall be located on the suction side of the reservoir. All filters shall be accessible for easy element replacement.

Shut-off valve shall be provided and installed to allow for cleaning.

Hydraulic fluid transmission lines shall be flexible hoses, wired braid reinforced and shall have a weather and abrasion resistant covering. Bursting pressure rating shall be at least 200% of the system operating pressure.

Hydraulic hose clamps (minimum 2 for each different hose diameter) and additional length of hydraulic hose (minimum 5 linear feet of each hose diameter) shall be provided in a repair kit that can be used in case of hydraulic hose leak or failure while performing an inspection.

14.G. CONTROLS AND SAFETY SYSTEM:

Controls:

Three complete sets of controls shall be provided:

1. One set of hydraulic controls at the pedestal.

2. One set of radio controls at the basket.

3. One set of radio controls for operation at the pedestal and from edge of bridge.

In case of electrical failure, the hydraulic valve at the pedestal shall be capable of overriding the radio controls.

All controls must be equipped with two-way, return to neutral type levers. All booms articulation and turret no. 1 and 2 shall have proportional flow control and precise metering capability to provide smooth operation of the unit in all working positions and to insure the safety of operating personnel at all times.

Controls shall be arranged to allow for each individual movement separately or in any combination desired.

Controls shall be located to facilitate maintenance access. Manual overrides shall be provided for all functions.

Remote carrier and auxiliary engine kill switches shall be installed at the pedestal and platform control station. A color display shall be provided at the pedestal with control of front and rear suspension lockouts, counterweight and accessories. It shall also display status of limit switch system.

Safety Devices:

1. Interlock to prevent operation of underbridge inspection aerial device if suspension lockouts are not engaged.

2. Limit switches to prevent rotation or articulation of booms into unstable positions.

3. Relief valve and switches to prevent overloading hydraulic system with excessive pressures.

4. Emergency kill switch of truck and auxiliary engines at the pedestal and basket

5. Automatic check valves on hydraulic cylinders in case of pump or hose failure.

6. Automatic audible alarm to signal excessive slope conditions.

7. All boom lift cylinder shafts shall be of chrome rods to resist corrosion and shall be able to withstand a 100 hour salt spray test.

14.H. TRUCK STABILIZERS:

The frame shall be equipped with four (4) hydraulically operated suspension lockouts, two at the front axle and two at the rear axle, controlled from the pedestal station. The lockout system shall include indicator lights to alert the driver that the lockouts are engaged or disengaged. Lights shall be installed in the cab.

An interlock shall be installed to prevent operation of the underbridge inspection aerial device when the suspension lockout system is disengaged. A manual override (to allow booms to be stowed in case of system malfunction) shall be installed at the pedestal.

When lockouts are engaged, the truck shall be capable of withstanding all tipping forces generated by booms in all positions in both stationary and moving applications.

OUTRIGGERS ARE UNACCEPTABLE.

14.I. COMMUNICATION SYSTEM:

An intercommunication system between personnel in the truck cab, the pedestal control station, the ground remote control station, and the work platform shall be provided and installed. System shall consist of:

1. A fully transistorized amplifier (powered by the truck batteries) with on/off switch, volume controls and an integral press-to-talk switch mounted in the truck cab convenient to the driver, and at the pedestal. The basket speaker shall be activated in a hands free mode.

14.J. ACCESSORIES:

1. A minimum 18 CFM @ 100 psi hydraulic driven air compressor shall be mounted on the truck body. The unit shall include a minimum 30 gallon capacity ASME stamped air receiver tank with safety valve, condensation drain, pressure gauge and globe valve. The tank shall be mounted under the truck bed.

2. An air line with a minimum 100 psi working pressure rating shall be provided to the work bucket. The air line shall be routed along the booms in protected areas and shall terminate at the bucket with a quick disconnect coupling.

3. Four (4) 115 volt, three (3) contact, weatherproof, grounding, receptacles shall be provided, 2 at the bucket and 2 at the truck platform. Receptacles shall be ground fault interruption protected.

4. Unit shall be equipped with a minimum single phase 60 Hz, AC generator which will be driven by the auxiliary diesel engine. Generator shall be a minimum 5 KW for the operation of the heaters, air compressor, flood lamps, and electrical outlets.

5. Bucket shall be equipped with two (2) 1500 watt, 5000 BTU, 115 volt, 60 Hz heaters with blower fans for the convenience of the workman during cold weather operations.

6. Bucket shall be equipped with one (1) folding shelf for workman in the bucket to place papers or other inspection equipment.

7. The bucket will be equipped with two (2) swivel mounted flood lamps with on/off switch.

13. Delivery:

Fully functional and assembled snooper truck shall be delivered to Tulsa District U.S. Army Corps of Engineers at the following address abcdefghijklmnopqrstuvwxyz. Delivery will occur no later than 120 calendar days from the Notice to Proceed date.

14. Training:

Training for operation and maintenance of the Chassis and Aerial Unit to be held in the Tulsa District for United States Army Corps of Engineers employees shall be included. Training will be a minimum of 2 days in length.

Section E - Inspection and Acceptance

CLAUSES INCORPORATED BY REFERENCE

52.246-1 Contractor Inspection Requirements APR 1984 52.246-2 Inspection Of Supplies--Fixed Price AUG 1996 52.246-16 Responsibility For Supplies APR 1984

Section F - Deliveries or Performance

DELIVERY INFORMATION

CLIN DELIVERY DATE QUANTITY SHIP TO ADDRESS DODAAC /

CAGE

52.242-15 Stop-Work Order AUG 1989 52.247-34 F.O.B. Destination NOV 1991

Section G - Contract Administration Data

252.201-7000 Contracting Officer's Representative DEC 1991 252.204-7006 Billing Instructions OCT 2005 252.232-7003 Electronic Submission of Payment Requests and Receiving

Reports

DEC 2018

Section I - Contract Clauses

52.202-1 Definitions NOV 2013 52.203-3 Gratuities APR 1984 52.203-6 Alt I Restrictions On Subcontractor Sales To The Government

(Sep 2006) -- Alternate I

OCT 1995

52.203-12 Limitation On Payments To Influence Certain Federal Transactions

OCT 2010

52.203-17 Contractor Employee Whistleblower Rights and Requirement To Inform Employees of Whistleblower Rights

APR 2014

52.204-4 Printed or Copied Double-Sided on Postconsumer Fiber Content Paper

MAY 2011

52.204-7 System for Award Management OCT 2018 52.204-10 Reporting Executive Compensation and First-Tier

Subcontract Awards

OCT 2018

52.204-13 System for Award Management Maintenance OCT 2018 52.204-16 Commercial and Government Entity Code Reporting JUL 2016 52.204-18 Commercial and Government Entity Code Maintenance JUL 2016 52.204-23 Prohibition on Contracting for Hardware, Software, and

Services Developed or Provided by Kaspersky Lab and Other Covered Entities.

JUL 2018

52.204-25 Prohibition on Contracting for Certain Telecommunications and Video Surveillance Services or Equipment.

AUG 2019

52.207-4 Economic Purchase Quantity-Supplies AUG 1987 52.209-6 Protecting the Government's Interest When Subcontracting

With Contractors Debarred, Suspended, or Proposed for Debarment

OCT 2015

52.209-10 Prohibition on Contracting With Inverted Domestic Corporations

NOV 2015

52.212-4 Contract Terms and Conditions--Commercial Items OCT 2018 52.223-1 Biobased Product Certification MAY 2012 52.223-15 Energy Efficiency in Energy-Consuming Products DEC 2007 52.223-18 Encouraging Contractor Policies To Ban Text Messaging

While Driving

AUG 2011

52.225-3 Buy American --Free Trade Agreement--Israeli Trade Act MAY 2014 52.225-25 Prohibition on Contracting with Entities Engaging in Certain

Activities or Transactions Relating to Iran-- Representation and Certifications.

AUG 2018

52.229-6 Taxes--Foreign Fixed-Price Contracts FEB 2013 52.232-8 Discounts For Prompt Payment FEB 2002 52.232-17 Interest MAY 2014 52.232-33 Payment by Electronic Funds Transfer--System for Award

Management

OCT 2018

52.232-39 Unenforceability of Unauthorized Obligations JUN 2013 52.232-40 Providing Accelerated Payments to Small Business

Subcontractors

DEC 2013

52.233-3 Protest After Award AUG 1996 52.233-4 Applicable Law for Breach of Contract Claim OCT 2004 52.237-2 Protection Of Government Buildings, Equipment, And

Vegetation

APR 1984

52.242-13 Bankruptcy JUL 1995 52.243-1 Changes--Fixed Price AUG 1987

52.246-23 Limitation Of Liability FEB 1997 52.247-27 Contract Not Affected by Oral Agreement APR 1984 52.249-8 Default (Fixed-Price Supply & Service) APR 1984 252.203-7000 Requirements Relating to Compensation of Former DoD

Officials

SEP 2011

252.203-7002 Requirement to Inform Employees of Whistleblower Rights SEP 2013 252.204-7000 Disclosure Of Information OCT 2016 252.204-7003 Control Of Government Personnel Work Product APR 1992 252.204-7015 Notice of Authorized Disclosure of Information for Litigation

Support

MAY 2016

252.232-7010 Levies on Contract Payments DEC 2006 252.243-7001 Pricing Of Contract Modifications DEC 1991 252.243-7002 Requests for Equitable Adjustment DEC 2012 252.244-7000 Subcontracts for Commercial Items JUN 2013

CLAUSES INCORPORATED BY FULL TEXT

52.209-11 REPRESENTATION BY CORPORATIONS REGARDING DELINQUENT TAX LIABILITY OR A

FELONY CONVICTION UNDER ANY FEDERAL LAW (FEB 2016)

(a) As required by sections 744 and 745 of Division E of the Consolidated and Further Continuing Appropriations Act, 2015 (Pub. L. 113-235), and similar provisions, if contained in subsequent appropriations acts, the Government will not enter into a contract with any corporation that--

(1) Has any unpaid Federal tax liability that has been assessed, for which all judicial and administrative remedies have been exhausted or have lapsed, and that is not being paid in a timely manner pursuant to an agreement with the authority responsible for collecting the tax liability, where the awarding agency is aware of the unpaid tax liability, unless an agency has considered suspension or debarment of the corporation and made a determination that suspension or debarment is not necessary to protect the interests of the Government; or

(2) Was convicted of a felony criminal violation under any Federal law within the preceding 24 months, where the awarding agency is aware of the conviction, unless an agency has considered suspension or debarment of the corporation and made a determination that this action is not necessary to protect the interests of the Government.

(b) The Offeror represents that--

(1) It is [ ] is not [ ] a corporation that has any unpaid Federal tax liability that has been assessed, for which all judicial and administrative remedies have been exhausted or have lapsed, and that is not being paid in a timely manner pursuant to an agreement with the authority responsible for collecting the tax liability; and

(2) It is [ ] is not [ ] a corporation that was convicted of a felony criminal violation under a Federal law within the preceding 24 months.

(End of provision)

52.212-5 CONTRACT TERMS AND CONDITIONS REQUIRED TO IMPLEMENT STATUTES OR

EXECUTIVE ORDERS—COMMERCIAL ITEMS (DEVIATION 2018-O0021) (OCT 2019)

(a) Comptroller General Examination of Record. The Contractor shall comply with the provisions of this paragraph

(a) if this contract was awarded using other than sealed bid, is in excess of the simplified acquisition threshold, and does not contain the clause at 52.215-2, Audit and Records—Negotiation.

(1) The Comptroller General of the United States, or an authorized representative of the Comptroller General, shall have access to and right to examine any of the Contractor’s directly pertinent records involving transactions related to this contract.

(2) The Contractor shall make available at its offices at all reasonable times the records, materials, and other evidence for examination, audit, or reproduction, until 3 years after final payment under this contract or for any shorter period specified in FAR Subpart 4.7, Contractor Records Retention, of the other clauses of this contract. If this contract is completely or partially terminated, the records relating to the work terminated shall be made available for 3 years after any resulting final termination settlement. Records relating to appeals under the disputes clause or to litigation or the settlement of claims arising under or relating to this contract shall be made available until such appeals, litigation, or claims are finally resolved.

(3) As used in this clause, records include books, documents, accounting procedures and practices, and other data, regardless of type and regardless of form. This does not require the Contractor to create or maintain any record that the Contractor does not maintain in the ordinary course of business or pursuant to a provision of law.

(b)(1) Notwithstanding the requirements of any other clauses of this contract, the Contractor is not required to flow down any FAR clause, other than those in this paragraph (b) (1) in a subcontract for commercial items. Unless otherwise indicated below, the extent of the flow down shall be as required by the clause—

(i) 52.203-13, Contractor Code of Business Ethics and Conduct (Oct 2015) (41 U.S.C. 3509).

(ii) 52.203-19, Prohibition on Requiring Certain Internal Confidentiality Agreements or Statements (Jan 2017) (section 743 of Division E, Title VII, of the Consolidated and Further Continuing Appropriations Act, 2015 (Pub. L.

113-235) and its successor provisions in subsequent appropriations acts (and as extended in continuing resolutions)).

(iii) 52.204-23, Prohibition on Contracting for Hardware, Software, and Services Developed or Provided by Kaspersky Lab and Other Covered Entities (Jul 2018) (Section 1634 of Pub. L. 115-91).

(iv) 52.204-25, Prohibition on Contracting for Certain Telecommunications and Video Surveillance Services or Equipment. (Aug 2019) (Section 889(a)(1)(A) of Pub. L. 115-232).

(v) 52.219-8, Utilization of Small Business Concerns (Oct 2018) (15 U.S.C. 637(d)(2) and (3)), in all subcontracts that offer further subcontracting opportunities. If the subcontract (except subcontracts to small business concerns) exceeds $700,000 ($1.5 million for construction of any public facility), the subcontractor must include 52.219-8 in lower tier subcontracts that offer subcontracting opportunities.

(vi) 52.222-17, Nondisplacement of Qualified Workers (MAY 2014) (E.O. 13495). Flow down required in accordance with paragraph (l) of FAR clause 52.222-17.

(vii) 52.222-21, Prohibition of Segregated Facilities (APR 2015).

(viii) 52.222-26, Equal Opportunity (Sept 2016) (E.O. 11246).

(ix) 52.222-35, Equal Opportunity for Veterans (Oct 2015) (38 U.S.C. 4212).

(x) 52.222-36, Equal Opportunity for Workers with Disabilities (July 2014) (29 U.S.C. 793).

(xi) 52.222-37, Employment Reports on Veterans (FEB 2016) (38 U.S.C. 4212).

(xii) 52.222-40, Notification of Employee Rights Under the National Labor Relations Act (Dec 2010) (E.O. 13496).

Flow down required in accordance with paragraph (f) of FAR clause 52.222-40.

(xiii) 52.222-41, Service Contract Labor Standards (Aug 2018) (41 U.S.C. chapter 67).

(xiv)(A) 52.222-50, Combating Trafficking in Persons (Mar 2015) (22 U.S.C. chapter 78 and E.O. 13627).

(B) Alternate I (Mar 2015) of 52.222-50 (22 U.S.C. chapter 78 and E.O. 13627).

(xv) 52.222-51, Exemption from Application of the Service Contract Act to Contracts for Maintenance, Calibration, or Repair of Certain Equipment-Requirements (May 2014) (41 U.S.C. chapter 67).

(xvi) 52.222-53, Exemption from Application of the Service Contract Act to Contracts for Certain Services- Requirements (May 2014) (41 U.S.C. chapter 67).

(xvii) 52.222-54, Employment Eligibility Verification (Oct 2015) (E.O. 12989).

(xviii) 52.222-55, Minimum Wages Under Executive Order 13658 (Dec 2015).

(xix) 52.222-62 Paid Sick Leave Under Executive Order 13706 (Jan 2017) (E.O. 13706).

(xx)(A) 52.224-3, Privacy Training (JAN 2017) (5 U.S.C. 552a).

(B) Alternate I (JAN 2017) of 52.224-3.

(xxi) 52.225-26, Contractors Performing Private Security Functions Outside the United States (Oct 2016) (Section 862, as amended, of the National Defense Authorization Act for Fiscal Year 2008; 10 U.S.C. 2302 Note).

(xxii) 52.226-6, Promoting Excess Food Donation to Nonprofit Organizations (May 2014) (42 U.S.C. 1792). Flow down required in accordance with paragraph (e) of FAR clause 52.226-6.

(xxiii) 52.247-64, Preference for Privately Owned U.S.-Flag Commercial Vessels (Feb 2006) (46 U.S.C. Appx.

1241(b) and 10 U.S.C. 2631). Flow down required in accordance with paragraph (d) of FAR clause 52.247-64.

(2) While not required, the contractor may include in its subcontracts for commercial items a minimal number of additional clauses necessary to satisfy its contractual obligations.

(End of clause)

52.222-50 COMBATING TRAFFICKING IN PERSONS (JAN 2019)

(a) Definitions. As used in this clause--

Agent means any individual, including a director, an officer, an employee, or an independent contractor, authorized to act on behalf of the organization.

Coercion means--

(1) Threats of serious harm to or physical restraint against any person;

(2) Any scheme, plan, or pattern intended to cause a person to believe that failure to perform an act would result in serious harm to or physical restraint against any person; or

(3) The abuse or threatened abuse of the legal process.

Commercially available off-the-shelf (COTS) item means--

(1) Any item of supply (including construction material) that is--

(i) A commercial item (as defined in paragraph (1) of the definition at FAR 2.101);

(ii) Sold in substantial quantities in the commercial marketplace; and

(iii) Offered to the Government, under a contract or subcontract at any tier, without modification, in the same form in which it is sold in the commercial marketplace; and

(2) Does not include bulk cargo, as defined in 46 U.S.C. 40102(4), such as agricultural products and petroleum products.

Commercial sex act means any sex act on account of which anything of value is given to or received by any person.

Debt bondage means the status or condition of a debtor arising from a pledge by the debtor of his or her personal services or of those of a person under his or her control as a security for debt, if the value of those services as reasonably assessed is not applied toward the liquidation of the debt or the length and nature of those services are not respectively limited and defined.

Employee means an employee of the Contractor directly engaged in the performance of work under the contract who has other than a minimal impact or involvement in contract performance.

Forced Labor means knowingly providing or obtaining the labor or services of a person--

(1) By threats of serious harm to, or physical restraint against, that person or another person;

(2) By means of any scheme, plan, or pattern intended to cause the person to believe that, if the person did not perform such labor or services, that person or another person would suffer serious harm or physical restraint; or

(3) By means of the abuse or threatened abuse of law or the legal process.

Involuntary servitude includes a condition of servitude induced by means of--

(1) Any scheme, plan, or pattern intended to cause a person to believe that, if the person did not enter into or continue in such conditions, that person or another person would suffer serious harm or physical restraint; or

(2) The abuse or threatened abuse of the legal process.

Recruitment fees means fees of any type, including charges, costs, assessments, or other financial obligations, that are associated with the recruiting process, regardless of the time, manner, or location of imposition or collection of the fee.

(1) Recruitment fees include, but are not limited to, the following fees (when they are associated with the recruiting process) for--

(i) Soliciting, identifying, considering, interviewing, referring, retaining, transferring, selecting, training, providing orientation to, skills testing, recommending, or placing employees or potential employees;

(ii) Advertising;

(iii) Obtaining permanent or temporary labor certification, including any associated fees;

(iv) Processing applications and petitions;

(v) Acquiring visas, including any associated fees;

(vi) Acquiring photographs and identity or immigration documents, such as passports, including any associated fees;

(vii) Accessing the job opportunity, including required medical examinations and immunizations; background, reference, and security clearance checks and examinations; and additional certifications;

(viii) An employer's recruiters, agents or attorneys, or other notary or legal fees;

(ix) Language interpretation or translation, arranging for or accompanying on travel, or providing other advice to employees or potential employees;

(x) Government-mandated fees, such as border crossing fees, levies, or worker welfare funds;

(xi) Transportation and subsistence costs--

(A) While in transit, including, but not limited to, airfare or costs of other modes of transportation, terminal fees, and travel taxes associated with travel from the country of origin to the country of performance and the return journey upon the end of employment; and

(B) From the airport or disembarkation point to the worksite;

(xii) Security deposits, bonds, and insurance; and

(xiii) Equipment charges.

(2) A recruitment fee, as described in the introductory text of this definition, is a recruitment fee, regardless of whether the payment is--

(i) Paid in property or money;

(ii) Deducted from wages;

(iii) Paid back in wage or benefit concessions;

(iv) Paid back as a kickback, bribe, in-kind payment, free labor, tip, or tribute; or

(v) Collected by an employer or a third party, whether licensed or unlicensed, including, but not limited to--

(A) Agents;

(B) Labor brokers;

(C) Recruiters;

(D) Staffing firms (including private employment and placement firms);

(E) Subsidiaries/affiliates of the employer;

(F) Any agent or employee of such entities; and

(G) Subcontractors at all tiers.

Severe forms of trafficking in persons means--

(1) Sex trafficking in which a commercial sex act is induced by force, fraud, or coercion, or in which the person induced to perform such act has not attained 18 years of age; or

(2) The recruitment, harboring, transportation, provision, or obtaining of a person for labor or services, through the use of force, fraud, or coercion for the purpose of subjection to involuntary servitude, peonage, debt bondage, or slavery.

Sex trafficking means the recruitment, harboring, transportation, provision, or obtaining of a person for the purpose of a commercial sex act.

Subcontract means any contract entered into by a subcontractor to furnish supplies or services for performance of a prime contract or a subcontract.

Subcontractor means any supplier, distributor, vendor, or firm that furnishes supplies or services to or for a prime contractor or another subcontractor.

United States means the 50 States, the District of Columbia, and outlying areas.

(b) Policy. The United States Government has adopted a policy prohibiting trafficking in persons including the trafficking-related activities of this clause. Contractors, contractor employees, and their agents shall not--

(1) Engage in severe forms of trafficking in persons…