A.07.23_Attachment_D_Salient_characteristics.pdf

Attachment D

“equal” items that meet the salient characteristics of the brand name items will be considered acceptable for award

Salient characteristics for an equivalent to “ Lo ct ite”

-Color: Blue

-Application Temperature: Apply above 50°F (10°C)

-Appearance: Liquid -Odor: low

-Base: Methacrylate ester

-Set Time: less than 15 minutes

-Cure Time: less than 48 hours

-Viscosity: 1200 cps @ 20 rpm

-Flashpoint: > 200°F (93°C)

Salient characteristics for an equivalent to Chesterton 155

-Adjustable/removable gland tabs

-360-degree flush port rotation

-Low heat generation monolithic faces

-Stationary springs

-Size: 25 mm to 120 mm 1.00" to 4.75"

-Pressure: 711 mm or 28" Hg Vacuum to 40 bar g / 600 psig

-Temp: –55°C to 300°C / –67°F to 570°F

Salient characteristics for an equivalent to Apexior -Marine grade, organic one component coating suitable for salt water immersion.

-Solids by volume 47%.

-SW immersion temperature resistance to 140 degrees F.

-Approx 750 sq. feet per gallon coverage

-Volatile Organic Compound content of 3.48 lb/gallon.

-Compatible with existing coating system

Salient characteristics for an equivalent to Jotamastic 87

-Marine grade, two component polyamine cured epoxy mastic coating for areas where optimum surface preparation is not possible

-Provides long lasting protection in highly corrosive environments

-Can be used as primer, mid coat, finish coat or as single coat system in atmospheric and immersed environments -Can be applied by brush, roller or spray

-Cure time less than 6 hours

-Induction time and pot life: Induction time between 5 and 15 minutes, pot life between 1-2 hours

-Heat resistance dry- 120degrees C

-Immersed in sea water 50-60 degrees C

Salient characteristics for an equivalent to Jontun safeguard

-Marine grade, epoxy vinyl based coating

-Fast drying, flexible

-Tie coat between epoxy primers and antifouling systems in immersed environments.

-Can be applied at sub zero surface temperatures.

-Applied by brush or spray

-Pot life between 1.5 and 2.5 hours

-Heat resistance immersed in sea water between 30-50 degrees C continuous or 40-60degrees C peak.

Salient characteristics for an equivalent to Jontun epoxy

-Marine grade, two component epoxy filler

-Solvent free product

-Drying times at 50% relative humidity surface touch less than 1 hour, hard dry between 1-4 hours, dried to coat

-Over between 1-4 hours.

-Cure time less than 48 hours

Salient characteristics for an equivalent to Jontun hardtop

-Marine grade, two component chemically curing aliphatic acrylic polyurethane coating -Glossy finish with very good gloss retention

-Used as topcoat in atmospheric environments

-Application by brush, roller or spray

-Drying time surface touch between 2 and 4 hours above 10 degrees C, dry to coat between 4-14 hours

-Cure between 3-7 days above 20 degree C and relative humidity below 85%

-Pot life between 1-2 hours

-Heat resistance dry continuous approx 120 degrees C, peak approximately 140 degrees.

Salient characteristics for an equivalent to Flowserve factory OEM parts

-Any part that the OEM authorizes to substitute

Salient characteristics for an equivalent to Bar-Rust 235

-Marine grade

-Exceptional corrosion protection

-Suitable for salt & fresh water immersion

-Low temperature cure to 0°F (-18°C)

-Surface tolerant – abrasive blasting not required in most applications -Good adhesion to damp surfaces

-Self-priming for steel & masonry substrates

-Excellent adhesion to tight rust

-Excellent abrasion & chemical resistance

-High solids – high film build

-Ultra low VOC

-Dry at 15 degrees C: Hard dry- between 9-11 hours

-Pot life at 15 degrees C: Between 3.5 and 4.5 hours

-Applied by brush, roller or spray

Salient characteristics for an equivalent to Chesterton Style 8000 Super Parachute

-Inside Diameter – 420 mm

-Outside Diameter – 460 mm

-Cross Section – 20 mm

-Split, 7 pieces per set

-One (1) top ring

-One (1) bottom ring

-Five (5) ‘V’ rings

Salient characteristics for an equivalent to Chesterton Style 5000 Super-Wiper -Inside Diameter – 420 mm

-Outside Diameter – 445 mm

-Dimension ‘B’, Mold #65989, Type 1

-Either split or un-split

-One (1) top ring

-One (1) bottom ring

-Five (5) ‘V’ rings

Salient characteristics for an equivalent to Jontun Barrier AV ZINC

-Marine grade, two component polyamide cured zinc rich epoxy coating

-Conforms to the compositional requirements of SSPC paint 20, level 2

-Provides very good corrosion protection as part of a complete coating system

-Used as primer in atmospheric environments

-Dry time at 23 degrees C surface touch less than 15 minutes, dry to coat

Salient cha ra ct eristics f o r a n equiv a lent to “ Densyl t a pe”

-Composed of a non-woven synthetic fabric carrier, fully impregnated with a neutral compound based on saturated petrolatum and inert siliceous fillers

-Designed to withstand extreme temperature variations

-Provides long term corrosion protection to pipes, flanges, valves and related surfaces

-Meets NACE RP0375-2000

-Meets AWWA C217 Standard -Can be applied to marginally prepared surfaces

-UV resistant and not effected by water, acid, salts or soil organics

-Does not contain solvents