44026-E1.pdf

44026-E1

E1

SCALE OF FEET

030 30 60

N

1 SCALE: 30’ = 1’-0"

E1

M2

M2

M

M

M

M7 M

M

M

OVERALL ELECTRICAL SITE PLAN

LEGEND

SPECIAL ELECTRICAL KEYED NOTES:

OVERALL ELECTRICAL SITE PLAN

SIT (STATIONARY INFANTRY TARGET)

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23

SEE ELECTRICAL SCOPE OF WORK FOR MORE DETAILS.

ALL EXTERIOR MOUNTED LOAD CENTERS TO BE NEMA 3R.

MINIMIZED.

BIRD-NESTING SEASONS, 15 MARCH THROUGH 31 MAY, CLEARING AND GRUBBING OPERATIONS SHALL BE

CONTRACTOR MAY PERFORM CONSTRUCTION WORK WITHIN THE NON-CORE HABITAT AREA; HOWEVER, DURING

UXO AREA TO GAIN ACCESS TO OTHER CONSTRUCTION AREAS.

UNEXPLODED ORDANCE (UXO) AREA AT ANY TIME; HOWEVER, CONTRACTOR MAY USE EXISTING ROADS IN THE

CONTRACTOR SHALL NOT ENCROACH OR PERFORM ANT CONSTRUCTION OPERATIONS WITHIN THE LIMITS OF THE

NO SPLICING OF ELECTRICAL CABLES BETWEEN MANHOLES AND EMPLACEMENTS.

ROW OR LANE COMMON TRENCHING.

ALL RANGE AREA PRIMARY, SECONDARY ELECTRICAL AND COMMUNICATION CABLE SHALL BE INSTALLED IN

ENCASED DUCTS THREE (3) FEETS BEYOND ROAD ON EACH SIDE.

ALL CONDUITS CROSSING ROADS AND SERVICE DRIVES WILL BE CONCRETE ENCASED. EXTEND CONCRETE

FORT BENNING DIRECTORATE OF PUBLIC WORK (DPW).

ALL PRIMARY OUTAGE WILL BE COORDINATED WITH THE AREA OFFICE OF CORP. OF ENGINEERS AND

NO SPLICING OF CABLES BETWEEN THE EMPLACEMENTS IS ALLOWED.

PERCENT OF THE SUPPLYING TRANSFORMER’S SECONDARY VOLTAGE.

OPERATING VOLTAGE AT THE MOST DISTANT EMPLACEMENT OR TARGET SHOULD NOT BE LESS THAN 95

FROM THE EMPLACEMENT.

DIRECT BURIED CABLES SHALL FEED EMPLACEMENTS THROUGH CONDUIT THAT IS STUBBED OUT 5 FEET

PENETRATION.

ACTUAL DEPTH OF THE CABLES SHALL BE DEEP ENOUGH TO PREVENT DANAGE FROM THE PROJECTILE

CONCRETE ENCASED DUCT BANKS MUST BE USED WHENEVER TRENCHING UNDERNEATH ROAD SYSTEMS.

MUCH AS PRACTICAL TO MINIMUM DISTURBANCE.

DESIGNER SHOULD ROUTE THE TRENCHES ALONG THE ACCESS ROADS AND THE MAINTENANCE TRAILS AS

ROADS AND MAINTENANCE ROADS.

REDUCE THE AMOUNT OF TRENCHING ON DOWN RANGE BY PLACING ELECTRICAL TRENCHES ALONG COURSE

CENTER FEEDERS FROM ROC-TOWER POWER PANELS PRIOR TO DETERMINING THE FEEDER WIRE SIZE.

IT IS IMPORTANT THAT DETAILED VOLTAGE DROP CALCULATIONS BE PERFORMED ON ALL TARGET LOAD

RANGES.

CAN CARRY THE LOAD OF THE ENTIRE RANGE IF ONE FEEDER MUST BACK FEED TARGETS ON OTHER

PHASES TO RUN DOWN RANGE, AND THE PRIMARY FEEDERS SHOULD BE SIZED SUCH THAT EACH FEEDER

THE DESIGNER SHOULD CONSIDER PHASE IMBALANCE ON UTILITY SYSTEM WHEN SELECTING SELECTING

THE DESIGNER SHOULD CONSIDER THE MEANS TO BACK FEED TARGETS EVERYWHERE PRACTICAL.

BE CLEAR OF TREES, BUSHES, STUMPS, LEDGE, LARGE ROCKS AND OTHER IMPEDIMENTS.

ALL TRENCH LINES SHALL BE NOT LESS THAN TEN FEET FROM THE ROAD. THE TRENCH ROUTE MUST

REQUIREMENTS WITHOUT EXCEPTION.

ALL EXCAVATION AND ROADWAY WORK SHALL ADHERE TO OSHA, DOT, AND FLINT ELECTRIC SAFETY

BY THE LOCAL UTILITY.

THE MINIMUM CABLE DEPTHS FOR MEDIUM VOLTAGE POWER ARE 48-INCH OR THE DEPTHS DETERMINED

CODE HAS A MINIMUM REQUIREMENTS FOR TRENCHING DEPTHS. FOR DOWNRANGE PORTION OF RANGES

THE POWER AND DATA CABLES SHALL BE INSTALLED IN THE SAME TRENCH. THE NATIONAL ELECTRIC

THE OSCAR 5 (MORRIS RANGE). USE FIBER OPTIC COMMUNICATION DISTRIBUTION SYSTEM.

CONTRACTOR IS REQUIRED TO DESIGN THE DOWNGROUND POWER AND DATA DISTRIBUTION SYSTEMS FOR

ELECTRICAL DESIGN FOR THE GOVERNMENT APPROVAL BEFORE STARTING THEIR WORK.

THIS IS 1 35% DESIGN BID DOCUMENTS. CONTRACTOR IS REQUIRED TO SUBMIT THE 100%

S Y

M B

O L

D A

T E

B Y

R E

V I S I O

N S

DRAWN BY:

APPROVED BY:

D.SAYLOR

L&E NO:

DRAWING NUMBER: SCALE:

AS NOTED

DATE:

FORT BENNING, GEORGIA

FORT BENNING, GEORGIA

F I L

E N

A M

E

DIRECTORATE

OF PUBLIC WORKS

K. CHAN

15 FEB 2019

PISTOL QUALIFICATION COURSE RANGE

CONVERT OSCAR 5 RANGE TO COMBAT