ATTACHMENT_2_-_PRS_Upgrade_Security_Control_Center_Bldg__4515_V3_R1_26_Apr_17.pdf

ATTACHMENT 2 -PRS Upgrade Security Control Center Bldg. 4515 V3 R1 26 Apr 17

Performance Requirement Summary (PRS)

Statemen ts Standards/AQLs Incentive/Remedy

3.1 Demolition.

3.1.1 Remove and a) Complete

dispose of plywood AQL: 100% compliance and trim around existing projection screen openings in preparation for sound abatement treatment IAW drawing appendix.

3.1.2 Remove air a) Complete

transfer vents at AQL: 100% compliance bottom of wall between mechanical area and control desk area and patch holes in preparation for sound abatement treatment, IAW drawing appendix.

3.1.3 Remove and a) Complete

dispose of all AQL: 100% compliance existing raised floor tiles.

3.1.4 Remove and a) Complete

dispose of existing AQL: 100% compliance outlets, flexible conduit, and junction boxes (spider boxes) under raised floor in desk area.

Retain existing circuits for re-use.

3.1.5 Remove and a) Complete

dispose of 4 fire AQL: 100% compliance suppression sprinkler heads in control desk area IAW drawing appendix. Cap lines at each location.

3.1.6 Remove and a) Complete

dispose of existing AQL: 100% compliance suspended ceiling grid tiles.

Statemen ts Standards/AQLs Incentive/Remedy

3.2 New Construction.

3.2.1 Provide new a) Complete

framing, as needed, AQL: 100% compliance inside existing projection screen openings. Finish with single layer of Type X 5/8" gypsum wall board to match surrounding wall.

3.2.2 Extend existing a) Complete

partition wall, AQL: 100% compliance between mechanical area and control desk area, to underside of roof deck, IAW drawing appendix.

3.2.3 Provide new sound a) Complete

abatement on entire AQL: 100% compliance wall between mechanical and desk areas. IAW drawing appendix.

3.2.4 Provide new raised a) Complete

floor tiles. Floor tiles AQL: 100% compliance shall consist of same number of airflow tiles as currently exist, arrangement of air flow shall be determine during construction

3.2.5 Repaint entire room a) Complete

(control desk area) AQL: 100% compliance IAW Drawing Appendix. Color and sheen to match existing.

3.2.6 Provide new a) Complete

suspended ceiling AQL: 100% compliance tiles in entire control desk area matching the existing original tiles.

3.2.7 Provide new

acoustic air transfer grilles (Typ. 4) between desk area and mechanical area. Grilles shall be placed at top of wall, just below suspended ceiling grid. Grilles shall be minimum of 550 CFM each.

a) Complete AQL: 100% compliance

3.2.8 Extend existing

outlets on wall between control desk area and mechanical area to new surface of wall due to sound abatement.

3.2.9 Provide two new

rows of four (4) under floor mounted quadplexreceptacles , approximately 3 feet from wall between desk area and mechanical area. Utilize retained circuits for new outlets.

3.2.10 Provide new clean

agent fire suppression system in control desk area and mechanical area. Clean agent fire suppression system components (tank, manifold, controls etc;) shall be installed in mechanical area in approximate location shown.

a) Complete AQL: 100% compliance

b) Compliant with applicable standards AQL: 100% compliance

c) Meets technical specifications AQL: 100% compliance

d) Compliant with federal, state, and local laws and regulations

Special Requirements

This section describes the special requirements for this effort. The following sub-sections provide details of various considerations on this effort.

ATTENTION:

REAL ID Act – 5 Jan 2016

Background: The REAL ID Act of 2005 establishes minimum standards for the production and issuance of state-issued driver licenses and identification cards which include requirements for a photograph and certain biographic information, such as name, DOB, gender, height, eye color & address. State-issued driver licenses and identification (ID) cards from states not meeting the standards cannot be used for accessing Federal facilities beginning 10 Jan 2016, unless the issuing state’s compliancy deadline has been extended by the Department of Homeland Security (DHS).

As of 31 Dec 2015, DHS indicates Driver Licenses and ID cards from the following states are not compliant with the standards of the REAL ID Act:

Illinois, Minnesota, Missouri, New Mexico and Washington

23 other states are pursuing compliancy for their programs and have an extended compliancy deadline of 10 Oct 2016; Alaska, California, New Jersey and South Carolina are included in the extended compliancy deadline list.

Current Status: Since many states are not yet compliant with the Act, DoD is pending a final policy implementation date. Once final implementation guidance is received from DoD, visitor control centers will no longer accept a non-REAL ID driver’s license for vetting without an additional form of identification which is specified in Directive Type Memorandum (DTM) 09- 012, Attachment 4:

• United States Passport or United States Passport Card

• Permanent Resident Card/Alien Registration Receipt Card (Form I-551)

• Foreign passport with a temporary (I-551) stamp or temporary (I-551) printed notation on a machine readable immigrant visa

• Employment authorization document that contains a photograph (Form I-766)

• In the case of a nonimmigrant alien authorized to work for a specific employer incident to status, a foreign passport with Form I-94 or Form I-94A bearing the same name as the passport and containing an endorsement of the alien’s nonimmigrant status, as long as the endorsement has not yet expired and the proposed employment is not in conflict with any restrictions or limitations identified on the form.

• Current/valid driver’s license from a Real ID Act-compliant state or state with a REAL ID Act extension for implementation

• Driver License or ID card issued by Federal or Local Government Agencies meeting REAL ID standards with photo, name, DOB, gender, height, eye color & address

• School identification card with a photograph

• U.S. Military or draft record

• U.S. Coast Guard Merchant Mariner Cards• Transportation Worker Identification Card

• Native American Tribal Document

All persons requesting unescorted access will continue to be vetted through the National Crime Information Center, prior to being issued a locally produced ID or pass. If a visitor requesting access does not have REAL ID Act compliant form of identification and cannot provide supplemental identity proofing documents, they must be escorted at all times while on the installation.

For the most current information concerning state-by-state compliance with the REAL ID Act, please visit https://www.dhs.gov/ current-status-states-territories.

Additional questions or concerns for OPMG Physical Security Branch and be addressed by Mr.

Kevin Palgutt at 703-693-2906.

GOVERNMENT INSPECTIONS, AUDITS, AND SURVEYS AND REQUESTS FOR

INFORMATION AND TECHNICAL ADVICE. In accordance with FAR 52.246-5, the contractor shall provide and maintain an inspection system acceptable to the Government covering the services under this contract. Complete records of all inspection work performed by the

Contractor shall be maintained and made available to the Government during contract performance and for as long afterwards as the contract requires. The Government has the right to inspect and test all services called for by the contract, to the extent practicable at all places and times during the term of the contract.

The Government shall perform inspections and tests in a manner that will not unduly delay the work. If any of the services performed do not conform with contract requirements, the

Government may require the contractor to perform the services again in conformity with contract requirements, for no additional fee. When the defects in services cannot be corrected by performance, the Government may (1) Require the contractor to take necessary action to ensure that future performance conforms to contract requirements; and (2) Reduce any fee payable under the contract to reflect the reduced value of the services performed. If the contractor fails to promptly perform the services again or take the action necessary to ensure future performance in conformity with contract requirements, the Government may

(1) By contract or otherwise, perform the services and reduce any fee payable by an amount that is equitable under the circumstances; or (2) Terminate the contract for default. "Services", as used in this clause, includes services performed, workmanship, and material furnished or used in performing services.

The contractor shall respond to all requests for information and technical advice regarding the services in this contract. Responses shall be either verbal or written, as specified by the requester.

https://www.dhs.gov/

Types of action shall include:

Responding to inquiries and suggestions.

Providing written comments based on review of draft documents such as regulations that affect the operations in this contract.

Providing information requested by customers, investigators, inspectors, auditors and members of special teams (both internal and external to AEC), and responding to findings of such inquiries.

Preparing reports in accordance with government instructions and directives by the requested due dates.

Attending on-site meetings as required by the Government.

LOST AND FOUND PROPERTY: If item(s) are found that do not belong to the contractor; the item(s) shall be turned in to the COR.

Security and Safety

The contractor will not have access to classified material however will be required to sign a non- disclosure agreement which simply states that anything they see or hear on Dugway

Proving Ground is not to be released or discussed with the public.

Public Release: No test data, reports or documents shall be released to other organizations unless authorized in writing by the Contracting Officer, assigned COR through the designated

ATEC/AEC Directorate, and the ATEC OPSEC Coordinator. Any information (classified or unclassified) pertaining to this contract shall not be released for public dissemination. Proposed public releases shall be submitted for approval prior to release to: Army Test and Evaluation

Command, ATTN: Security Office, Aberdeen Proving Ground, MD 21005.

Foreign Personnel: In accordance with restrictions required by Executive Order 12470, the Arms

Export Control Act (Title 22, United States [US] Code [USC]) (Sec 275), the International

Traffic in Arms Regulation (ITAR), or Department of Defense (DoD) Directive 5230.25, Withholding of Unclassified Technical Data from Public Disclosure, no foreign persons will be permitted to work on a contract without notifying the Contracting Officer.

*** ATTENTION ***

CAC HOLDERS: Level I Antiterrorism Awareness Training course (JS-US007) is now hosted on the Joint Knowledge Online (JKO) Learning Management System (LMS) for CAC holders at https://Jkodirect.jten.mil.(Level I Antiterrorism Awareness Training, JS-US007) Login and Search for the course on the Course Catalog tab via the number or key word, enroll, and Launch.

Requirement for OPSEC Training: Per AR 530-1, Operations Security, new contractor employees must complete Level 1 OPSEC training within 30 calendar days of their reporting for duty. All contractor employees must complete annual OPSEC awareness training. The government will provide supplemental guidance i.e. ATEC policies.

https://jkodirect.jten.mil/ https://jkodirect.jten.mil/html/COI.xhtml?course_prefix=JS&course_number=-US007

Information Assurance (IA)/Information Technology Training: IA/IT training and/or certification is not required under this contract.

Information Assurance/Information Technology Training Certification: IA/IT training and/or certification is not required under this contract.

Handling or Access to Classified Information: Contractor shall comply with FAR 52.204-2, Security Requirements. This clause involves access to Information classified "Confidential", "Secret", or "Top Secret" and requires contractors to comply with-(1) The Security Agreement

(DD Form 441), including the National Industrial Security Program Operating Manual (DoD

5220.22-M); any revisions to DOD 5220.22-M, notice of which has been furnished to the contractor. The government will provide supplemental guidance, i.e. ATEC policies.

Personnel Security: Contractor and associated sub-contractor employees will comply with AR

380-67. Foreign travel and contact will be reported. The government will provide supplemental guidance, i.e.

ATEC policies.

Transition

There will be no transition involved with this contract, the contractor will completed the install, test and training then the government will take responsibility for the effort.

Government Furnished Materials - None

Management of Government-Furnished Property and Equipment: None

For any contractor working in a Government facility, the following shall be provided:

Telephone Service: The Government may provide phone service in support of the contract supporting the government

Network Access: Network access will not be provided to the contractor.

Custodial and Refuse Services: The Government will provide custodial and refuse services for the Government facilities used in performance of this contract. The Governments provision of custodial and refuse services do not relieve the contractor of the responsibility for keeping work areas in a clean and sanitary condition. In some areas, the contractors shall be required to empty trash from office/shop trashcans to dumpsters.

Copying, Printing, and Reproduction: The Government will provide shared-use copy machines for limited copying of official reports, documents, and correspondence to accomplish the requirements of specific tasks.

Environmental Requirements

The contractor shall comply with all federal, state and local code involving environmental concerns.

Facility construction will comply with Unified Facilities Criteria (UFC) DoD Minimum Antiterrorism Standards for Buildings (UFC 4-010-01)

Applicable Directives

PUBLICATIONS: The following publications are applicable to the overall performance of this

PWS. The contractor is required to adhere to the most current version of any of the published regulations found below. Army, State and Federal regulations are publicly available on the internet. Other publications can be obtained by contacting the Contract Specialist for an electronic version. In addition to documentation listed in the Blanket

Purchase Agreements (BPAs), the following documents will apply to the operational data analysis support:

Department of Defense Directives (DoDD) 5000.1, the Defense Acquisition System, 12 May 2003.

DoDD 8000.1, Management of DoD Information Resources and Information Technology, 20

March 2002.

DoDD 5000.2-R, Mandatory Procedures for Major Defense Acquisition Programs (MDAPs) and Major Automated Information System (MAIS) Acquisition Programs, 12 May 2003.

Army Regulation (AR) 25-3, Army Life Cycle Management of Information

Systems AR 73-1, Test and Evaluation Policy, 30 May 2003.

Department of Army (DA) Pamphlet 73-7, Test and Evaluation Software Test and Evaluation

Guidelines MDA System Capability Specification

GMD Capabilities Document (GCD).

National Defense Authorization Act Section 234

DoD Instruction 5134.9, Missile Defense Agency (MDA)

AR 381-11 Intelligence Support to Capability

Development AR 385-10 The Army Safety Program

AR 700-127 Integrated Product Support

Army Universal Task List (AUTL)

ATEC PAM 73-21 Modeling and Simulation Verification, Validation, and Accreditation Methodology

ATEC Regulation 73-1 System Test and Evaluation Policy

ATEC Regulation 73-21 Accreditation of Models and Simulations for Test and

Evaluation DA PAM 385-16 System Safety Management Guide

DA PAM 385-30 Mishap Risk Management

DA PAM 5-11 Verification, Validation, and Accreditation of Army Models and Simulations

DA PAM 73-1 Test and Evaluation in Support of Systems Acquisition

MIL-STD 882E System Safety

TOPM 73-182 System Test and Evaluation

Policy Universal Joint Task List (UJTL)

Unified Facilities Criteria (UFC) DoD Minimum Antiterrorism Standards for Buildings (UFC 4-010-

01) ALARACT 012/2012

Integrating Antiterrorism and Operations Security into the Contract Support Process--Desk Reference