Attachment_0003_-_Maintenance_and_Overhaul_Guidance.pdf

08/01/2019

M900PRID 179-60500-5Part Number

6110-01-123-0157NSN CH-47System

CONTROL GENERATORNomenclature

YAdequate DMWR Available?

DMWR-55-6110-227DMWR ID

07/19/2013DMWR Date

DMWR Chg #

YPre-Award Survey Recommended?

NCorrelation Performance Study Required ? YPVA Recommended?

(1) The overhaul facility is responsible for acquisition, maintenance, calibration, and disposition of all Test, Measurement and Diagnostic Equipment (TMDE). TMDE shall be maintained and controlled in accordance with MIL-I-45607, AMCOM-R-70202 or NCSL Z540.3. Calibration documents for all TMDE shall be traceable to the National Institute of Standards of Technology

(NIST).

(2) See DMWR 55-6110-227 paragraph 4-1 for Final Assembly and testing procedures and paragraphs 4-2 through 4-6 for final testing procedures. The overhaul facility shall have special tools and test/inspection equipment as specified in DMWR 55-6110- 227 paragraphs 2-2.a through 2-2.b. All substitute and equivalent tooling shall require Government approval. The solicitation/RFP shall require that all proposals/responses include a special tooling and test equipment section that addresses the contractor's plan to meet all government special tooling and test equipment requirements with either:

- Physical possession of the required tools.

- Confirmed requisitions for the required tools.

- Confirmed arrangements for subcontracting the processes requiring the special tools.

- Specific plans describing their technical approach to develop equivalent tools.

Identify Any Special Processes, Test Procedures, and/or Instructions

NCritical Safety Item?

There are no emerging airworthiness issues, no issues related to ECPs affecting the CSI status, and no concerns over reliability/durability for the CH-47 Control Generator at the time of this review.

Special Airworthiness Considerations

AED Notes: FCDD-AMA-M-Sustainment has verified the CSI/NST status through the ARISE CIM database on 21 May 2019.

The part is Non-CSI and Non-NST. DEM

Other Requirements / Comments

If the item is not a CSI and no adequate DMWR is available, approved sources, if any, are listed by CAGE as follows:

NSpecial Post-Contract Award Requirements?

Special Post-Contract Award Requirements

The applicable DMWR contains detailed procedures regarding IUID requirements for this component. These procedures can be found in MEO D2335, D2336A, and D2337.

Other Requirements / Comments (Part II)

AED Notes: FCDD-AMA-M-Sustainment has re-verified the CSI/NST status through the ARISE CIM database on 19 June 2019.

The part is Non-CSI and Non-NST. DEM

Other Requirements / Comments (Part III)

Other Requirements / Comments (Part IV)

Other Requirements / Comments (Part V)

NDoes QE-STD-2 Apply?

N

Additional CSI Requirements

CSI Contains CSI Replacement Parts? NEngineering Testing Required?

The solicitation/RFP shall require that all proposals/responses include a special tooling and test equipment section that addresses the contractor's plan to meet all government special tooling and test equipment requirements with either:

1. Physical possession of the required tools, 2. Confirmed requisitions for the required tools, 3. Confirmed arrangements for subcontracting the processes requiring the special tools, or 4. Specific plans describing their technical approach to develop equivalent tools.

RStatus

YTDPL?

Approved Date

M&O AED REQUIREMENTS DATA

Commerciality Determination

Commercial Item? N NBest Commercial Practice Acceptable?

08/01/2019

M900PRID 179-60500-5Part Number

6110-01-123-0157NSN CH-47System

C4598

D1178A

D2042

D2335

D2336A

D2337

See Tables 2-1 and 2-2 of DMWR 55-6110-227 for special tools, inspection and test equipment.

Critical Tools and Test and Inspection Equipment Requiring AED Approval for Substitutes

MEOs Required for Competitive Contract?

RStatus

Correlation Performance Study Requirements