SPI P806650-01revB.pdf

S P E C IA L P A C K A G IN G IN S T R U C T IO N (S P I)

DO D SPI INDEX NUM BER

NO M ENCLATURE

SPI NUM BER

Q UPUI

EA 1

P806650---01

DRAW ING/PART NO.

U N IT PACK AN D M ILITARY PRESERVATIO N REQ U IREM EN TS

NATIO NAL STO CK NUM BER

AP15689658

806650---01SHOULDER ANCHOR STRAP

8465---01---568---9658

ITEM WEIGHT ---

APPROVAL REVISION DATE

0.1 lbs.

05 May 2009PAGE NUMBER NUMBER OF PAGES

545---0001---003 ---

DISTRIBUTION STATEMENT A: Approved for public release. Distribution is Unlimited.

RP

STEPS SPECIFICATION STYLE TYPE GRADE CLASS SIZE AND REMARKS (INCHES)

UNIT PACK LOGISTICS DATA (Approximate unit pack weight and size)

WEIGHT (POUNDS) CUBE (CUBIC FEET)

I N T E R M E D I AT E P AC K AG I N G

M AR K I N G

REMARKS

(B)1 Heat SealClosure (C)2

QUALITY PERFORMANCE & TESTING REQUIREMENTS

MIL---DTL---117

IAW MIL---STD ---2073---1

As specified hereon.

IAW MIL---STD ---129

As specified hereon.

IAW MIL---STD ---2073---1

As specified hereon. SEE NOTE (E)

0.1 lbs.

X ( )

( )X

( )X

X

0.005 cu. ft.

SIZE (EXTERIOR INCHES)

3 x 6 x 0.5

UNIT PACK MATERIALS

Clean and dry in accordance with (IAW) MIL---STD---2073---1 using any applicable method that is not injurious to the item.

Container (Bag)

Methods of Preservation (MOP) --- 31

2 III B 3 x 6

LEVEL OF PACK (EXTERIOR PACKAGING): Level A and B IAW MIL---STD ---2073---1 & Contract As specified hereon.( )

( )X

The current revision to each of the specifications, standards, and drawings listed on this SPI in effect on the date of invitation for bid constitute a mandatory part of this Instruction. Unless otherwise specified, materials will be minimum size IAW MIL---STD ---2073---1 or material specifications. Tolerances shall be IAW material specifications.

Clean and dry in accordance with (IAW) MIL---STD---2073---1 using any applicable method that is not injurious to the item.

(A) --- This SPI is not applicable for Interplant shipments. Packaging and marking for interplant shipments are for supplies and materials that do not directly enter the military supply system. Typical interplant shipments are shipments from a vendor to a subcontractor or a prime contractor, or between contractors and subcontractors, or from a vendor or contractor to a military arsenal, plant, or other activity for evaluation, immediate use, or further processing as specified in the applicable contract.

(B) --- Fold Shoulder Anchor Strap three times onto itself to approximate dimensions of 3 1/2 x1 x1/2 inches.

Insert folded Shoulder Anchor Strap into specified bag (Step 1). Bag material shall conform to A---A---3174 as specified in MIL---DTL---117 and shall have an minimum thickness of 4 mil.

ITEM SIZE ---

ITEM SI

545---0212---005

545---0098---015

B

A

16 Dec 2020

20 Jan 2011

Original Preparer:

RFR

DBH

Revised by:

10 3/4 x 1 x 1/8

ITEM SIZE ---

ITEM CODE ---

ITEM DATA

R. Poole Regina Ryan inches

(APPROX)

Date: 27 Oct 2020

ITEM CODE ---

Date: 31 Oct 2008

CCDC CBC

81361

DOD SPI INDEX NUMBER

NOMENCLATURE

SPI NUMBER

P806650---01

PAGE NUMBER

DRAWING/PART NO.

NATIONAL STOCK NUMBER

AP15689658

806650---01SHOULDER ANCHOR STRAP

8465---01---568---9658

(C) --- Closure (Step 2) of bag shall be accomplished by heat sealing in accordance with the barrier bag or barrier material supplier’s recommendations for dwell, pressure and temperature requirements. The volume of trapped air within the bag shall be kept to a minimum by compressing the bag around the contents, or carefully drawing a vacuum inside the bag, prior to final heat sealing. Caution shall be taken to prevent damage to the item or rupture of bag.

(D) --- Palletization and Unitization: The shipping container, when not requiring skids, shall be placed on the pallet IAW MIL---STD ---147 and ANSI MH1 when:

---Shipments of identical items packed in shipping container(s) exceed the total of 50 cubic feet per destination and do not exceed the size or weight limitations for palletized loads.

---The total number of containers, not having identical items going to the same destination, weighs 250 pounds or greater (excluding pallet), or has a volume of 20 cubic feet or greater and does not exceed the size or weight limitations for palletized loads.

(E) --- Packaging Quality Assurance Provisions:

This section outlines the requirements for conducting appropriate quality conformance inspections, examinations, tests and acceptance for packaging and shall be required as specified in the contract.

1. Classification of inspections. The inspection requirements for the packaged item described herein are conducted during First Article Testing (FAT) and Production Lot Testing (Conformance).

2. First Article Testing. The first article inspection and approval (if FAT is required by the contract) consists of the contractor inspection of items prior to regular production. Note: If required, packaging inspections shall be part of the FAT and be included as part of the FAT Report submittal to the Government (see paragraph 2.d). The first article testing shall be conducted as follows:

a. Sampling. The first article packaging sample shall consist of not less than three unit pack containers and their contents, and when heat seal seam testing is required, three empty barrier bags.

Packaged samples shall be produced using the same methods, materials and equipment as will be used during regular production.

b. Visual Examination and Tests. Shall be as specified in MIL---STD ---2073---1, Appendix G, and:

(1). Packaged samples shall be examined IAW the preservation examinations to determine compliance IAW Table G ---I of MIL---STD ---2073---1.

(2). Leakage and heat seal seam tests are required for sealed containers as specified in Table G ---II of MIL---STD ---2073---1. Note: Method of Preservation 10 does NOT require tests.

(3). Compliant wood requirements shall be IAW the contract. Examination shall include review and acceptance of wood packaging material, containers, pallets and dunnage.

DOD SPI INDEX NUMBER

NOMENCLATURE

SPI NUMBER

P806650---01

PAGE NUMBER

DRAWING/PART NO.

NATIONAL STOCK NUMBER

AP15689658

806650---01SHOULDER ANCHOR STRAP

8465---01---568---9658

(4). The level of pack shall be as specified in the contract. The exterior shipping configuration shall include examination to verify compliance with MIL---STD ---2073---1 guidelines for intermediate and shipping containers for the level of pack specified.

(5). Packaged samples shall be marked IAW MIL---STD ---129.

c. Certificate of Compliance. Certification shall be required for ALL packaging materials, containers, including level of pack, and palletization materials specified in this SPI. Format shall be IAW the contract and shall include, at a minimum, the contractor’s name, address, phone number, contract number, item name, part number and/or national stock number, a statement specifying with what it complies (i.e. material, size, specification, standard), dated, printed name and title of certifying official, and shall be signed.

d. Packaging Inspections in the FAT Report: The packaging inspection results and documents shall be included in and as part of the FAT Report submittal. At a minimum, it shall include the following information:

(1) Test data (leakage and heat seal seam tests), if required (see 2.b.(2))

(2) Certificate of compliance sheets (see 2.c), including intermediate and/or shipping containers (level of packs) and palletization materials, even if not used as part of the packaging FAT

(3) Preservation/packaging inspection provisions

(4) Photographs of the unit pack(s) including opened package with the item packed inside

(5) Photographs of markings/labels for each packaging configuration

(6) Photographs of the packing configuration including box seal certification, if applicable

e. Acceptance criteria. Samples that fail to comply with any of the applicable requirements shall be rejected.

3. Production Lot Testing (Conformance).

a. Sampling. Sampling size shall be IAW the Attributes Sampling Plan Table of MIL---STD ---1916 for visual examination. Verification Level I shall be used. If required, three samples from the sampling size shall be selected for destructive testing (leakage and heat seal seam tests). Existing sampling plans in item specifications or quality assurance provisions shall take precedence.

b. Visual Examinations and Tests. Shall be conducted IAW 2.b above. If applicable, destructive testing will be conducted after visual examination.

c. Certificate of Compliance. Shall be prepared IAW 2.c above unless the contractor submits a letter of conformance stating that the packaging materials are the same as those that passed the FAT.