Atch_01,_PWS,_NG-0031-18.pdf

USATA-NG-0031-18

PERFORMANCE WORK STATEMENT

FOR REPAIR AND CALIBRATION OF ANRITSU SIGNAL GENERATOR

1.0 GENERAL. The U.S. Army Test, Measurement and Diagnostic Equipment Activity (USATA) has a requirement to acquire commercial repair and calibration of the following test, measurement and diagnostic equipment manufactured by Mahr Federal, Inc.:

Comparator, Mahr Model 130B-16, Serial No. 8016 Precimar Measuring Machine, Mahr Model PLM 600-2, Serial No. 1102-08

2.0 CONTRACTOR TASKS.

2.1 Reference Mahr RMA Number 021817NMBA, a preliminary evaluation of the Comparator, Model 130B-16, indicates the unit requires repair and calibration, to include reinstallation of the 130B-16 after repairs are completed. Reinstallation will take place at the government’s facility at Warren, MI. Mahr Federal, as the original equipment manufacturer, shall provide repair and calibration to the unit per manufacturer’s specifications.

2.2 Reference Mahr RMA 110317NMB, a preliminary evaluation of the Precimar Measuring Machine, Model PLM 600-2, indicates that the machine is not communicating with it’s mainframe. Contractor shall provide repair on site at the government’s facility at Rock Island Arsenal, IL and restore the unit to factory specifications.

2.3 The contractor shall replace defective parts, as required, with original equipment manufacturer parts only. The contractor shall strictly comply with turn-around-time to repair as stated in Section B of the contract.

2.4 The contractor shall not provide any repair or other services outside the scope of this contract without authorization from the government Contracting Officer listed at page 1 of the contract. The contractor shall not hold equipment at the contractor’s facility outside of the contract period of performance stated in Section B of the contract without authorization from the Contracting Officer.

3.0 GOVERNMENT TASKS.

The U.S. Army TMDE Activity, Redstone Arsenal, AL (Acceptance DODAAC: W80RA6) shall be responsible for receiving, inspection and acceptance in DFAS Wide Area Workflow (WAWF) for the unit.

USATA NG-0031-18

Attachment 01

4.0 PLACE OF PERFORMANCE. Performance shall take place at the government’s facilities respectively located at Warren, MI and Rock Island, IL as an on-site maintenance call, as follows:

4.1 U.S. Army TMDE Support Center – Rock Island, Building 131, Second Floor, Gillespie Street, Rock Island, IL 61299-7430.

4.2 U.S. Army TMDE Support Center – Warren, 6501 East 11 Mile Road, Building 203, M/S S118, Warren, MI 48397-5000.

5.0 PERIOD OF PERFORMANCE. See Section B of contract.

6.0 GOVERNMENT-FURNISHED EQUIPMENT. None.

7.0 QUALITY REQUIREMENTS. Not Applicable.

8.0 CONTRACTOR MANPOWER REPORTING REQUIREMENT – SERVICE

CONTRACTS.

(NOTICE: MANDATORY REQUIREMENT)

8.1 Department of the Army requires reporting of all contractor labor hours associated with services, to include calibration and repair, provided to United States Army organizations; therefore, 82 The contractor shall report ALL contractor labor hours (including subcontractor labor hours) required for performance of services provided under this contractor for the U.S.

Army TMDE Activity via secure data collection site. The contractor is required to completely fill in all required data fields using the following web address:

https://ecmra.mil.

8.3 Reporting inputs will be for the labor executed during the period of performance during each Government fiscal year (FY), which runs October 1 through September 30.

While inputs may be reported any time during the FY, all data shall be reported no later than October 31 of each calendar year, beginning with 2018. Contractors may direct questions to the help desk by clicking on “Send an email” which is located under the Help Resources ribbon on the right side of the login page of the applicable Service/Component’s CMR website.

https://ecmra.mil/