ACC-APG_Digital IF_Draft Technical Specfication doc_W15P7T-27-R-DIGIF.docx
DOCX document 826 KB Posted
- Solicitation number
- W15P7T-27-R-DIGIF
About this file
This is a Draft Technical Specification document supporting a Commercial Solution Opening (CSO) Call for Solutions for a Commercial Digital Intermediate Frequency Subsystem (DIFS) under the Army's Wideband Enterprise Satellite Systems (PdM WESS) modernization initiative.
The Product Manager Wideband Enterprise Satellite Systems is soliciting COTS Digital Intermediate Frequency solutions to replace legacy analog infrastructure and enhance scalability, resilience, and interoperability across satellite communications operations. The selected vendor will deliver, integrate, install, and acceptance-test a flexible, open-standard, modular Digital IF solution across up to twenty (20) worldwide SATCOM teleport sites, with Increment 1 establishing a fully operational baseline for subsequent capability upgrades and integration. The solicitation is issued under Army Open Solicitation (AOS) CSO Number W9128Z-25-S-A002 by Army Contracting Command - Aberdeen Proving Ground (ACC-APG). Questions regarding the opportunity are due by 05 November 2026 at noon EST, and Solution Briefs must be submitted via Sam.gov and AOS by 10 December 2026 at noon EST. This document was added via Amendment 0001 on 02 November 2026 with no extension to the established due dates. The contracting officer is Licinda Peters (licinda.m.peters.civ@army.mil) and the contract specialist is Keith Magaw (keith.a.magaw.civ@army.mil). The information is marked as CUI under Operations Security (OPSEC) with Limited Dissemination Control (FEDCON).
View the file
Other files
| File | Type | Posted |
|---|---|---|
| ACC-APG Digital IF_Call for Solutions_16Nov2026 Amendmnt 0003.pdf | ||
| ACC-APG Digital IF CfS_ QAs_12Nov2026.xlsx | XLSX spreadsheet | |
| ACC-APG Digital IF_Call for Solutions_12Nov2026 Amendmnt 0002.docx | DOCX document | |
| ACC-APG Digital IF_Call for Solutions_12Nov2026 Amendmnt 0002 clean.pdf | ||
| ACC-APG Digital IF CfS_ Questions Template_Attch 0001.xlsx | XLSX spreadsheet | |
| ACC-APG Digital IF_Call for Solutions_29October2026.docx | DOCX document |
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
UNCLASSIFIED
System Specification for XXX Specification No. A3425425
PRODUCT MANAGER WIDEBAND ENTERPRISE SATELLITE SYSTEMS (PdM WESS)
SYSTEM SPECIFICATION
for Increment 1 of the Digital Intermediate Frequency (IF) Subsystem (DIFS)
SPECIFICATION NO. A3425425
5 June 2026
VERSION 1.2
History of Changes
| Document No. |
| Date |
| Change Description |
| A3425425 |
| 11/24/2025 |
| Woody Scott Edits to APG and AJV Shell |
| A3425425 |
| 11/28/2025 |
| Woody Scott – Dave Khalil – review with edits posted to share |
| A3425425 Ver. 0.1 |
| 1/21/2026 |
| Al Berg – content added to sections 3.1, 3.2 and 4.3.2 |
| A3425425 Ver. 0.2 |
| 2/10/2026 |
| A.J. Vigil – added new 3.2.1, reworked EVM, etc. |
| A3425425 Ver. 0.3 |
| 2/12/2026 |
| SMS Tech Team Format Review |
| A3425425 Ver. 0.4 |
| 2/13/2026 |
| Engineering Team Review |
| A3425425 Ver. 1.0 |
| 2/14/2026 |
| Final Edits for Release – Dr. Berg and Woody Scott |
| A3425425 Ver. 1.1 |
| 5/18/2026 |
| Incorporated management automation – Al Berg and Ron Elliott |
| A3425425 Ver. 1.2 |
| 6/5/2026 |
| Incorporated comments from Minh Dinh Nguyen (JSEC) |
Contents
| 1. | SCOPE | 1 |
| 1.1 | Identification | 1 |
| 1.2 | Application | 1 |
| 2. | APPLICABLE DOCUMENTS | 1 |
| 2.1 | Government Documents | 1 |
| 2.2 | Non-Government Documents | 2 |
| 3. | REQUIREMENTS | 4 |
| 3.1 | Item Definition | 4 |
| 3.1.1 | Item Diagrams | 4 |
| 3.1.2 | Interface Definition | 5 |
| 3.1.2.1 | Digital IF Interfaces | 5 |
| 3.1.2.2 | Internal Interfaces | 7 |
| 3.1.2.3 | External Interfaces | 7 |
| 3.1.3 | Major Component List | 11 |
| 3.1.4 | Government Furnished Property (GFP) | 12 |
| 3.2 | Characteristics | 12 |
| 3.2.1 | Performance | 12 |
| 3.2.1.1 | Transmit Performance | 12 |
| 3.2.1.2 | Receive Performance | 15 |
| 3.2.1.3 | Communication Carriers | 17 |
| 3.2.1.4 | Cybersecurity | 17 |
| 3.2.1.5 | Information Technology Standards | 18 |
| 3.2.1.6 | Life Expectancy | 18 |
| 3.2.1.7 | Item Turn-On | 18 |
| 3.2.2 | Physical Characteristics | 18 |
| 3.2.2.1 | General | 18 |
| 3.2.2.2 | Equipment Racks | 18 |
| 3.2.2.3 | Equipment Modules | 19 |
| 3.2.2.4 | Interconnecting Cables | 19 |
| 3.2.2.5 | Weight | 20 |
| 3.2.3 | Reliability | 20 |
| 3.2.3.1 | System Availability | 20 |
| 3.2.3.2 | Reserved | 20 |
| 3.2.4 | Maintainability | 20 |
| 3.2.4.1 | Mean Time to Repair (MTTR) | 20 |
| 3.2.4.2 | Fault Detection and Isolation | 20 |
| 3.2.4.3 | Maintenance Design | 21 |
| 3.2.5 | Environmental Conditions | 22 |
| 3.2.5.1 | Sheltered Equipment Non-Operating and Equipment in Storage | 22 |
| 3.2.5.2 | Sheltered Equipment Operating | 23 |
| 3.2.5.3 | Seismic Events | 23 |
| 3.3 | Design and Construction | 23 |
| 3.3.1 | Materials, Processes and Parts | 24 |
| 3.3.1.1 | Equipment Finish | 24 |
| 3.3.1.2 | Corrosion Control | 24 |
| 3.3.1.3 | Prohibited Materials | 24 |
| 3.3.2 | Electromagnetic Environmental Effects (E3) | 24 |
| 3.3.2.1 | Electromagnetic Compatibility (EMC) | 24 |
| 3.3.2.2 | Electromagnetic Interference (EMI) | 24 |
| 3.3.2.3 | Grounding, Bonding and Shielding | 25 |
| 3.3.2.4 | Electrostatic Discharge (ESD) | 26 |
| 3.3.3 | Nameplates and Product Marking | 27 |
| 3.3.4 | Workmanship | 27 |
| 3.3.5 | Interchangeability | 27 |
| 3.3.6 | Safety | 28 |
| 3.3.6.1 | Electrical Safety | 28 |
| 3.3.6.2 | Battery Box Design Safety | 29 |
| 3.3.6.3 | Mechanical Safety | 30 |
| 3.3.6.4 | Safety Markings and Labels | 31 |
| 3.3.6.5 | Environmental and Chemical Safety | 31 |
| 3.3.6.6 | Additional Safety Provisions | 32 |
| 3.3.7 | Human Engineering | 32 |
| 3.3.7.1 | General Requirements | 32 |
| 3.3.7.2 | Acoustic Noise Level | 32 |
| 3.3.8 | Software and Computer Resources | 32 |
| 3.4 | Reserved | 32 |
| 3.5 | Reserved | 32 |
| 3.6 | Personnel | 32 |
| 3.7 | Major Component Characteristics | 32 |
| 3.7.1 | DIFI Switch Fabric | 32 |
| 3.7.2 | CD | 33 |
| 3.7.3 | IFC | 33 |
| 3.7.4 | DIFI TMDE | 34 |
| 3.7.4.1 | DIFI Vector Signal Generator (VSG) and Vector Signal Analyzer (VSA) | 34 |
| 3.7.4.2 | Spectrum Monitoring Function (SMF) | 34 |
| 3.7.5 | Frequency and Time Reference Distribution Amplifiers | 35 |
| 3.7.6 | DIFS Management Automation Software Suite (DMASS) | 35 |
| 3.7.6.1 | Automation Functions | 35 |
| 3.7.6.2 | Equipment Parameters Monitored by the DMASS | 40 |
| 3.7.6.3 | Equipment Parameters Controlled by the DMASS | 41 |
| 3.7.6.4 | DMASS Software Requirements | 42 |
| 3.7.6.5 | DMASS HCI | 43 |
| 3.7.6.6 | DMASS User Types and Privileges | 44 |
| 3.8 | Precedence | 45 |
| 4. | QUALITY ASSURANCE PROVISIONS | 45 |
| 4.1 | General | 45 |
| 4.1.1 | Responsibility for Tests | 45 |
| 4.1.1.1 | Government Responsibility | 46 |
| 4.1.1.2 | Contractor Responsibility | 46 |
| 4.1.2 | Test Procedures | 46 |
| 4.1.2.1 | Automated Test Procedures | 47 |
| 4.1.2.2 | Test Fixtures, Cables, and Interface Devices | 47 |
| 4.1.3 | Accuracy of Test Equipment | 47 |
| 4.1.4 | Test Phases | 47 |
| 4.1.4.1 | First Article Test (FAT) | 48 |
| 4.1.4.2 | Production Acceptance Test (PAT) | 48 |
| 4.1.5 | Reserved | 48 |
| 4.2 | Quality Assurance Program | 48 |
| 4.2.1 | Verification Cross Reference Matrix (VCRM) | 48 |
| 4.2.1.1 | Inspection (I) | 49 |
| 4.2.1.2 | Analysis (A) | 49 |
| 4.2.1.3 | Demonstration (D) | 49 |
| 4.2.1.4 | Test (T) | 49 |
| 4.2.1.5 | No Test Required (NT) | 49 |
| 4.2.1.6 | Certificate of Conformance (COC) | 49 |
| 4.3 | Verification of Requirements | 50 |
| 4.3.1 | Item Definition | 50 |
| 4.3.1.1 | Item Diagram | 50 |
| 4.3.1.2 | Interface Definition | 50 |
| 4.3.1.3 | Major Component List | 51 |
| 4.3.1.4 | Government Furnished Property | 51 |
| 4.3.2 | Characteristics | 51 |
| 4.3.2.1 | Performance | 51 |
| 4.3.2.2 | Physical Characteristics | 55 |
| 4.3.2.3 | Reliability | 55 |
| 4.3.2.4 | Maintainability | 56 |
| 4.3.2.5 | Environmental Conditions | 56 |
| 4.3.3 | Design and Construction | 58 |
| 4.3.3.1 | Materials, Processes and Parts | 58 |
| 4.3.3.2 | Electromagnetic Environmental Effects | 58 |
| 4.3.3.3 | Nameplates and Product Marking | 59 |
| 4.3.3.4 | Workmanship | 59 |
| 4.3.3.5 | Interchangeability | 59 |
| 4.3.3.6 | Safety | 59 |
| 4.3.3.7 | Human Engineering | 60 |
| 4.3.4 | Reserved | 60 |
| 4.3.5 | Reserved | 60 |
| 4.3.6 | Personnel | 60 |
| 4.3.7 | Major Component Characteristics | 60 |
| 4.3.7.1 | DIFI Switch Fabric | 60 |
| 4.3.7.2 | CD | 60 |
| 4.3.7.3 | IFC | 60 |
| 4.3.7.4 | DIFI TMDE | 60 |
| 4.3.7.5 | Frequency and Time Reference Distribution Amplifiers | 60 |
| 4.3.7.6 | DIFS Management Automation Software Suite | 60 |
| 4.3.8 | Precedence | 60 |
| 5. | PACKAGING | 60 |
| 6. | NOTES | 60 |
| Appendix A: Acronyms and Abbreviations | A-1 | |
| Appendix B: Verification Cross Reference Matrix (VCRM) | B-1 | |
| Appendix C: Digital IF Sampling Parameters and Stream Rates | C-1 |
FIGURES
| Figure 3‑1: DIFS Block Diagram | 4 |
| Figure 3‑2: DIFS Management Architecture | 5 |
| Figure 3‑3: External Interface Diagram | 8 |
| Figure 3-4: DIFS Increment 1 Major Digital IF Components | 12 |
| Figure 3‑5: DIFS Radiated Emissions Limits | 26 |
TABLES
| Table 3‑1: RS103 Emission Characteristics | 26 |
| Table 3‑2: Lifting Limits | 30 |
| Table C‑1: Digital IF Sampling Parameter and Stream Rate Examples | C-2 |
UNCLASSIFIED
UNCLASSIFIED
System Specification for Digital IF Subsystem Specification No. A3425425
UNCLASSIFIED
UNCLASSIFIED
System Specification for IncREMENT 1 of the Digital IF Subsystem
SCOPE
Identification This specification establishes the performance, design, fabrication, and test requirements for Increment 1 of the Digital IF Subsystem (DIFS). The DIFS will be a component of the Enterprise Wideband Satellite Communications (SATCOM) Terminal System (EWSTS) and will provide Digital Intermediate Frequency Interoperability (DIFI) infrastructure for Department of War (DOW) Enterprise SATCOM Systems.
Application The DIFS will be used to support United States (US) DOW, agency, special user, and allied communications requirements.
APPLICABLE DOCUMENTS
Government Documents The following documents of the exact issue shown, or latest version at time of Request for Proposal (RFP) release, if undated, form a part of this specification to the extent specified herein. In the event of conflict between this specification and the documents referenced herein, the precedence shall be as defined in Paragraph 3.8.
Standards MIL-STD-130N(1) – Identification Marking of US Military Property, 16 November 2012 MIL-STD-188-124B(4) – Grounding, Bonding and Shielding for Common Long Haul/Tactical Communication Systems Including Ground Based Communications-Electronics Facilities and Equipment, 4 April 2013 MIL-STD-188-164C(2) – Interoperability of Super High Frequency (SHF) Satellite Communications Terminals, 29 April 2025 MIL-STD-188-165B(2) - Interoperability of SHF Satellite Communications Phase-Shift Keying (PSK) Modems, 9 May 2025 MIL-STD-461H – Requirements for the Control of Electromagnetic Interference Characteristics of Subsystems and Equipment, 17 April 2026 MIL-STD-810H(1) – Environmental Engineering Considerations and Laboratory Tests, 18 May 2022 MIL-STD-882E(1) – DoD Standard Practice for System Safety, 27 September 2023 MIL-STD-889D(1) – Galvanic Compatibility of Electrically Conductive Materials, 29 April 2026 MIL-STD-1472H(1) – Department of Defense Design Criteria Standard, Human Engineering, 10 April 2026 Handbooks MIL-HDBK-217F(2) w/ Notice 1 – Reliability Prediction of Electronic Equipment, 2 June 2022 MIL-HDBK-310 – Global Climatic Data for Developing Military Products, 23 June 1997 Other Publications US Army Communications-Electronics Life Cycle Management Command (C-E LCMC) A3274102 – Cabinet, Electrical Equipment, Rev. E, 12 January 2006 CECOM-TB-7A – Battery Compartment Design Guidelines for Equipment Using Lithium Sulfur Dioxide Batteries, October 1997 Department of Defense (DOD) DOD Instruction 8510.01 – Risk Management Framework for DOD Information Technology, 19 July 2022 DoD Information Technology (IT) Standards Registry (DISR), https://www.dsp.dla.mil/Specs-Standards/List-of-DISR-documents/ WB C-SSE Terminal Performance Certification Test Procedures, latest revision at time of RFP release (Version 3.40, 2 April 2024 or later) National Institute of Standards and Technology (NIST) Special Publication (SP) 800-53, Security and Privacy Controls for Federal Information Systems and Organizations, latest revision at time of RFP release (Revision 5.2.0, 27 August 2025 or later) United States Army Capability Production Document for the Enterprise Wideband SATCOM Terminal System (EWSTS), 28 March 2006 United States Code of Federal Regulations (CFR) 29CFR1910 – Code of Federal Regulations, Title 29, Part 1910, Occupational Health and Safety Standards Federal Acquisition Regulation (FAR) FAR 52.225-5 Trade Agreements Copies of specifications, standards, and other publications required by suppliers in connection with specific procurement functions should be obtained from the contracting agency or as directed by the Procurement Contracting Officer (PCO).
Non-Government Documents The following documents of the exact issue shown form a part of this specification to the extent specified herein. In the event of conflict between this specification and the documents referenced herein, the precedence shall be as defined in Paragraph 3.8.
American Conference of Governmental Industrial Hygienists (ACGIH) ACGIH Threshold Limit Values (TLVs) and Biological Exposure Indices (BEIs), 2026 American National Standards Organization (ANSI) ANSI C63.16-2016 – American National Standard Guide for Electrostatic Discharge Test Methodologies and Criteria for Electronic Equipment ANSI Z136.1-2022 – American National Standard for Safe Use of Lasers ANSI Z136.2-2012 – American National Standard for Safe Use of Optical Fiber Communication Systems Utilizing Laser Diode and LED Sources ANSI Z535.4-2023 – American National Standard for Product Safety Signs and Labels Electronic Industries Association (EIA) EIA-310-E – Cabinets, Racks, Panels, and Associated Equipment, December 2005 Institute of Electrical and Electronic Engineers (IEEE) IEEE-1588-2019 – IEEE Standard for a Precision Clock Synchronization Protocol for Networked Measurement and Control Systems, 16 June 2020 IEEE-ISTO Std 4900-2021 – Digital IF Interoperability Standard, latest revision at time of RFP release (Version 1.3.0, 9 July 2025 or later) IEEE Std 802.3-2022 – IEEE Standard for Information technology – Telecommunications and Information Exchange Between Systems – Local and Metropolitan Area Networks – Specific Requirements, Part 3: Carrier Sense Multiple Access with Collision Detection (CSMA/CD) Access Method and Physical Layer Specifications A. J. Vigil and D. A. Khalil, "SATCOM Digital IF Stream Rate Considerations for Earth Segment Transport," MILCOM 2019 - 2019 IEEE Military Communications Conference (MILCOM), Norfolk, VA, USA, 2019, pp. 82-88, doi: 10.1109/MILCOM47813.2019.9020926.
International Electrotechnical Committee IEC 60950-1 – Information Technology Equipment - Safety - Part 1: General Requirements, 2005 including amendments through 2013.
Internet Engineering Taskforce (IETF) IETF RFC 768 – User Datagram Protocol, 28 August 1980 IETF RFC 791 – Internet Protocol, September 1981 IETF RFC 9293 – Transmission Control Protocol, August 2022 Joint Solid State Technology Association JESD471 – Symbol and Label for Electrostatic Discharge Sensitive Devices, October 2024 Society of Automotive Engineers (SAE) AMS-STD-595B – Colors Used in Government Procurement, 6 May 2026 Telcordia GR-63-CORE – NEBS Requirements: Physical Protection, Issue 5, December 2017 SR-332 – Reliability Prediction Procedure for Electronic Equipment, Issue 4, March 2016 Underwriters Laboratories (UL) UL 969 – Safety Markings and Labels, Edition 6, (including revisions through 28 July 2025)
REQUIREMENTS
Item Definition The DIFS specified herein is intended to support strategic Digital IF implementations in teleport, gateway, and Regional Hub Node (RHN) facilities. The DIFS is equipped for extending/replacing L-band components currently deployed worldwide. DIFS configurations will include Digital IF Converters (IFC), Digital IF Combiner/Dividers (CD), a dedicated Digital IF switching fabric, and Digital IF Test, Measurement and Diagnostic Equipment (TMDE). DIFS will interface with DIFI Standard compliant Digital IF Modems (DMs) to be procured separately.
Item Diagrams The functional block diagram of the DIFS, illustrating major components and their internal interfaces, is shown in Figure 3-1. The DIFS management architecture is shown in Figure 3-2. The DIFS Management Automation Software Suite (DMASS) exists as one or more virtual machines (VMs) on a virtualization host provided by others.
Note: Redundancy not shown for clarity Figure 3‑1: DIFS Block Diagram
Figure 3‑2: DIFS Management Architecture Interface Definition Digital IF Interfaces These requirements apply to all Digital IF interfaces, whether internal or external.
Digital IF Protocols All Digital IF interface datalink, network, transport, session, presentation and application layer protocols shall be in accordance with IEEE-ISTO Std 4900-2021, specifically Information Class 0 (zero). Jumbo frames shall be supported but not generated by any DIFS Digital IF source, neither internally nor externally.
All Digital IF source and sink ports shall support Digital IF stream sample depths from 4 to 16 bits. Digital IF ports shall be capable of supporting the following sample rates:
a. up to 300 megasamples per second (MSamp/s) for nominal modem streams, i.e. one mission per stream at the DIFS interface
b. up to 1250 MSamp/s for combined streams, i.e. entire satellite bands on internal interfaces
c. up to 1250 MSamp/s for potential occasional modem missions, e.g.:
1. raw sampled multi-frequency time division multiple access (MF-TDMA) raw sampled frequency hop spread spectrum (FHSS) direct sequence spread spectrum (DSSS) missions.
cascaded CD operation Digital IF ports shall conform to additional sampling parameter guidance indicated in Appendix C “Digital IF Sampling Parameters and Stream Rates” with examples indicated in Table C-1.
Dual Ethernet Ports Each Digital IF physical interface shall present two Ethernet ports for the purpose of supporting the following capabilities:
1. spine-leaf network architecture make-before-break network cut-over.
dual networks redundancy general flexibility Physical Ethernet port pairs shall support the spine-leaf network architecture as follows:
Establish a single virtual Media Access Control (MAC) and Internet Protocol (IP) address for each port pair.
On loss of port function, reassign virtual MAC & IP addresses to the other port in the pair and switch over to it.
When lost port function is restored, that port becomes the backup for the newly activated port.
Digital IF Port Operation All Digital IF source and sink ports shall support unicast for stream operation. All Digital IF source and sink ports shall also support multicast for stream operation using Internet Group Management Protocol (IGMP). All Digital IF sources shall produce Digital IF streams with individual DIFI Standard “Data Packets” spaced uniformly in time. All Digital IF streams shall maintain digital signal levels throughout each signal chain to within 90% of full scale sampling amplitude without operator intervention.
Digital IF Port Monitoring Digital IF equipment (IFCs, CDs and DIFI TMDE), for all streams on all sources and sinks on all ports, shall monitor and report, on both one-second and one-minute bases:
1. full scale power in decibels referenced to one milliwatt (dBm) peak power in dBm peak sampling power in decibels referenced to full-scale (dBFS) average power in dBm average sampling power in dBFS sample depth in bits.
sampling noise floor in dBm per Hertz (dBm/Hz) sampling noise floor in dBFS per Hertz (dBFS /Hz) Digital IF equipment, for all streams on all sources and sinks on all ports, shall monitor and report:
packet rate in packets/s.
DIFI Standard “data packet” size in bytes stream rate in megabits per second (Mbps).
Digital IF equipment, for all streams on all sources and sinks on all ports, shall monitor and report:
Average jitter, total, in ms, on both one-second and one-minute bases Maximum (positive) and minimum (negative) deviation of time between packets, total, until it is reset.
Lost packet count, total until it is reset.
Internal Interfaces Internal switch fabric interfaces are specified for DIFS major components in Paragraphs 3.7 and its subparagraphs. Other internal interfaces are as defined by the contractor. All internal interfaces shall be provided with connectors, connector panels, and labels. To the maximum extent practicable, internal interfaces shall be implemented using industry or Government standards. No proprietary interfaces shall be used, and all interfaces shall be fully documented in the DIFS Product Data as defined in the Statement of Work (SOW).
External Interfaces The DIFS external interfaces, shown in Figure 3-3, are as specified in the following paragraphs. Unless otherwise specified, all external interfaces shall be provided with connectors, connector panels and labels. Throughout this document, instantaneous bandwidth is defined as the bandwidth available, without the need for tuning or explicit selection (untuned bandwidth), that is consistent with the phase linearity and amplitude response requirements specified in MIL-STD-188-164.
Note: Each Modernization of Enterprise Terminals (MET) requires up to three L-Band aggregate interfaces. MET sites have up to 3 MET terminals. Each RHN terminal requires one L-Band aggregate interface. RHN sites have up to 3 RHNs.
Figure 3‑3: External Interface Diagram DM Interfaces The DIFS shall provide Digital IF interfaces (DM ports) for interoperation with local and remote DMs. The physical layer DM interface shall be configurable for 100GBASE-SR4 in accordance with IEEE 802.3bm and 100GBASE-LR4 in accordance with IEEE 802.3ba by provisioning the switch fabric with corresponding Quad Small Form-factor Pluggable 28 (QSFP28) modules. The network layer shall be configurable for Internet Protocol (IP) version 4 (IPv4) in accordance with Request for Comments (RFC) 791 and IP version 6 (IPv6) in accordance with IETF STD 86.
Aggregate Analog Intermediate Frequency (IF) Interfaces The DIFS shall provide the aggregate analog IF interfaces described below. With respect to the non-damage levels specified below, damage is defined as a permanent condition of the DIFS input port circuitry whereby the input signal cannot be received by the DIFS, or the input signal is distorted by the input port circuitry to the point that the requirements of this specification cannot be met.
Aggregate Analog Modem L-Band Inputs The DIFS shall accept a minimum of 9 aggregate analog modem L-Band IF input signals conforming to the characteristics specified below from a collocated L-Band Switch Subsystem (LBSS) provided by others. The characteristics of the input ports provided by the DIFS shall be as specified below. These input ports shall be made available within the Electronic Equipment Building (EEB).
1. Input signal characteristics:
Frequency range: 950 megahertz (MHz) to 2.050 gigahertz (GHz) Level range: +10 to -50 dBm.
Input port characteristics:
6. Instantaneous bandwidth: 1 GHz minimum tunable within the range specified above
6. Non-damage level: +20 dBm minimum continuous
6. Voltage standing wave ratio (VSWR): 1.5:1 maximum.
6. Impedance: 50 ohms (nominal)
6. Connector: Type N Aggregate Analog Modem L-Band Outputs The DIFS shall provide a minimum of 9 aggregate analog modem L-Band IF outputs as specified below to a collocated LBSS provided by others. These output ports shall be made available within the EEB.
1. Frequency range: 950 MHz to 2.050 GHz Instantaneous bandwidth: 1 GHz tunable within the range specified above Output 1 dB compression level: 0 dBm minimum into 50 ohms VSWR: 1.5:1 maximum Impedance: 50 ohms (nominal) Connector: Type N Aggregate Analog L-Band Downlink Inputs The DIFS shall accept a minimum of 9 L-Band analog inputs, each of which contains an aggregated earth terminal satellite downlink. Input signal and port characteristics for the aggregate inputs shall be in accordance with Paragraph 3.1.2.3.2.1 above. At selected sites, these inputs shall be made available within the EEB for connection to existing uplink combiner plates. At other sites, these interfaces shall be made available at the antenna (provided by others).
Aggregate Analog L-Band Uplink Outputs The DIFS shall provide a minimum of 9 L-Band analog outputs, each of which contains an aggregated earth terminal satellite uplink. The port characteristics for the aggregate outputs shall be in accordance with Paragraph 3.1.2.3.2.2 above. At selected sites, these outputs shall be made available within the EEB for connection to existing downlink divider plates. At other sites, these interfaces shall be made available at the antenna (provided by others).
Frequency and Timing Reference Interfaces The DIFS shall provide the frequency and timing reference interfaces described below. The frequency and timing reference interfaces shall be made available within the EEB. With respect to the non-damage levels specified below, damage is as defined in Paragraph 3.1.2.3.2.
10 MHz External Frequency Reference Input The DIFS shall accept a 10 MHz external frequency reference input signal conforming to the characteristics specified below. The characteristics of the input port provided by the DIFS shall be as specified below.
1. Input signal characteristics:
Frequency: 10 MHz sinusoidal Level range: 0.5 to 2.0 volts root-mean-square (VRMS) Input port characteristics:
Non-damage level: 4.0 VRMS minimum continuous VSWR: 1.5:1 maximum Impedance: 50 ohms (nominal) Connector: Type N External Timing Reference Input The DIFS shall accept an external 1 pulse per second (pps) timing reference input signal conforming to the characteristics specified below. The characteristics of the input port provided by the DIFS shall be as specified below.
1. Input signal characteristics:
Frequency: 1 pps Levels: +2.0 to +5.0 volts (V) when true, 0.0 to +0.8 V when false Input port characteristics:
Non-damage level: 10 V minimum continuous, any polarity Impedance: 50 ohms ±10% Connector: Type N External Management Interface The DIFS shall provide an interface to permit external control of all DIFS equipment configuration and operating parameters, and external monitoring of all DIFS equipment and performance status. The External Management Interface shall be made available within the EEB. The management protocol stack shall be as specified below:
1. Physical layer: 1000BASE-T in accordance with IEEE 802.3ab.
1. Network layer: Configurable for IPv4 in accordance with RFC 791 and IPv6 in accordance with IETF STD 86.
1. Transport layer: User Datagram Protocol (UDP) in accordance with RFC 768 or Transmission Control Protocol (TCP) in accordance with RFC 9293
1. Application layer: Web services Application Programming Interface (API) using protocols such as Representational State Transfer (REST) or Simple Object Access Protocol (SOAP) over TCP.
Precision Time Protocol (PTP) Interface The DIFS shall provide an interface to enable precision time synchronization of DIFS subsystems to a PTP Grandmaster Clock (provided by others). The PTP interface shall be made available within the EEB. The PTP interface shall share the same physical interface as the External Management Interface. The PTP protocol stack shall be as specified below:
1. Network layer: Configurable for IPv4 in accordance with RFC 791 and IPv6 in accordance with IETF STD 86.
1. Transport layer: UDP in accordance with RFC 768
1. Application layer: in accordance with IEEE-1588 Prime Power Interface The DIFS shall provide dual redundant alternating current (AC) prime power inputs. The failure of either power source shall not result in interruption of communications or loss of control of the DIFS. DIFS rack AC power inputs shall be provided with connectors located in the rack top panels. Connectors supplying mission equipment AC power shall be type MS3452W16-10P. Connectors supplying rack convenience outlets (see Paragraph 3.2.2.2, subparagraph g) shall be type MS3454L16-10PW. The pin assignments of both connector types shall be: A – line, B – neutral, C – ground.
Normal Operation The DIFS shall operate from a prime power source with the following characteristics:
1. Voltage: 120 volts AC (VAC) ± 10 percent Frequency: 47.5 to 63 Hz Phase: 1 phase, 3 wire Total harmonic distortion of voltage waveform: 5% maximum Transients The DIFS shall withstand any transient (less than one minute) input power to the extent described below without damage to any DIFS equipment:
1. Voltage: 120/208 VAC ±20 percent
1. Frequency: 45 to 66 Hz Load Current Unless approved by the government, the load current drawn by any one DIFS prime power input shall not exceed 15 amperes.
Major Component List The DIFS shall be composed of the following major components. Figure 3-4 provides a brief description of and recommended symbology for the Digital IF components.
1. DIFI Switch Fabric
1. CD
1. IFC
1. DIFI TMDE
1. Frequency and Time Reference Distribution Amplifiers
1. DMASS
Figure 3-4: DIFS Increment 1 Major Digital IF Components Government Furnished Property (GFP) No GFP will be incorporated into the DIFS. MD-1418 EDIM Modems and Digital IF Vector Analyzers (DIVAs) will be provided as Government furnished Equipment (GFE) to support development and First Article Test (FAT).
Characteristics Performance This specification has been prepared in coordination with MIL-STD-188-164 and MIL-STD-188-165. Unless otherwise noted, definitions of all performance parameters shall be IAW MIL-STD-188-164 and MIL-STD-188-165.
Transmit Performance DM Port through Aggregate Analog L-Band Uplink Output Error Vector Magnitude (EVM) degradation through DIFS uplink signal chains, DM port through analog uplink interface, shall be limited as follows:
1. Where L-Band IF conversion is employed, EVM degradation from the DM source port to the IFC L-Band output shall be limited to ≤ 2% in a root-sum-squared (RSS) sense.
Where direct Radio Frequency (RF) conversion is employed, EVM degradation from the DM source port to the RF Converter (RFC) RF output shall be limited to ≤ 2.8% in an RSS sense.
EVM degradation limits shall apply to 16-ary Amplitude and Phase Shift Keying (16-APSK) modulation in scenarios supporting multiple carriers.
EVM degradation limits shall apply to all signals where DIFI Standard “Usable Bandwidth” does not overlap.
EVM degradation limits shall apply to adjacent waveforms, where usable bandwidth abuts, to carriers whose Power Spectral Densities (PSDs) differ by up to 13 dB.
EVM degradation limits apply after accounting for noise floor contributions relevant to test scenario conditions as opposed to the signal chain.
Aggregate Analog L-Band Modem Input to Aggregate Analog Uplink L-Band Uplink Output The following requirements apply to all DIFS signal paths from IFC aggregate analog modem inputs through one or more cascaded Digital IF CD to IFC aggregate analog uplink outputs via the DIFI switch fabric. These requirements allocate a portion of the MIL-STD-188-164 Transmission Function performance requirements to DIFS, with the balance reserved for the SATCOM terminal Transmit Subsystem receiving its uplink from DIFS and to the transmit portion of any LBSS feeding DIFS.
Transmit Instantaneous Bandwidth All DIFS aggregate analog modem input to aggregate analog uplink output transmit signal paths shall be capable of supporting a maximum instantaneous bandwidth of no less than 1 GHz. Instantaneous bandwidth is defined in Paragraph 3.1.2.3.
Transmit Gain The net per-carrier transmit digital gain of the aggregate analog modem input to aggregate analog uplink output signal paths shall be 0 dB. Analog gain adjustment for equipment alignment is specified in Paragraph 3.7.3.
Transmit Level Stability The level stability of any transmit carrier traversing a DIFS aggregate analog modem input to aggregate analog uplink output signal path shall not be degraded by more than 1 dB peak-to-peak in any 24 hour period (see MIL-STD-188-164 Paragraph 4.2.4).
Transmit Frequency Conversion Accuracy The DIFS transmit frequency conversion accuracy of the aggregate analog modem input to aggregate analog uplink output transmit signal paths shall be within ±1 kHz of the intended value for all carriers (see MIL-STD-188-164 Paragraph 4.2.5).
Transmit Phase Linearity The DIFS transmit phase linearity of the aggregate analog modem input to aggregate analog uplink output transmit signal paths shall be no greater than 50% of that allowed by MIL-STD-188-164 Paragraph 4.2.7.
Transmit Amplitude Response The DIFS transmit amplitude response of the aggregate analog modem input to aggregate analog uplink output signal paths shall not exceed the following (see MIL-STD-188-164 Paragraph 4.2.8):
a. 0.5 dB peak to peak over any 10 MHz segment across the instantaneous bandwidth.
b. 1.0 dB peak to peak over any 120 MHz segment, or any smaller segment, across the instantaneous bandwidth (10 MHz < segment < 120 MHz).
c. 2.0 dB peak to peak over 1.0 GHz.
Transmit Spectral Purity The contribution of the DIFS to the spectral purity of any transmit carrier traversing any aggregate analog modem input to aggregate analog uplink output signal path shall be as follows.
AC Power Line The sum of AC line frequency components produced by DIFS shall not exceed -40 decibels referenced to the carrier (dBc) (see MIL-STD-188-164 Paragraph 4.2.9).
Single Sideband The single sideband sum (added on a power basis) of all other individual spurious components produced by DIFS shall not exceed -46 dBc (see MIL-STD-188-164 Paragraph 4.2.10).
Phase Noise The single-sided power spectral density of the continuous phase noise component produced by DIFS shall meet the requirements of MIL-STD-188-164 Figure 2 with a 3 dB margin.
Transmit Thermal Noise Transmit thermal noise produced by any DIFS aggregate analog modem input to aggregate analog uplink output signal path with the IFC aggregate analog modem inputs terminated shall not exceed -81 dBm/Hz (see MIL-STD-188-164 Paragraph 4.2.12).
Transmit Spurious Outputs Transmit spurious outputs produced by DIFS aggregate analog modem input to aggregate analog uplink output signal paths shall meet the requirements of MIL-STD-188-164 Paragraph 4.2.13 and its subparagraphs with a 6 dB margin. For DIFS, the non-transmit band of MIL-STD-188-164 Paragraph 4.2.13 subparagraph b shall be 2.0 GHz ≤ frequency ≤ 4.0 GHz.
Transmit EVM EVM degradation through DIFS uplink signal chains, aggregate L-Band modem input port through analog uplink interface, shall be limited as follows:
1. Where L-Band IF conversion is employed, EVM degradation from the aggregate L-Band modem input through the IFC L-Band output shall be limited to ≤ 2.8% in an RSS sense.
Where direct RF conversion is employed, EVM degradation from the aggregate L-Band modem input through the RFC RF output shall be limited to ≤ 3.4% in an RSS sense.
EVM degradation limits shall apply to 16-ary Amplitude and Phase Shift Keying (16-APSK) modulation in scenarios supporting multiple carriers.
EVM degradation limits shall apply to all signals where DIFI Standard “Usable Bandwidth” does not overlap.
EVM degradation limits shall apply to adjacent waveforms, where usable bandwidth abuts, to carriers whose PSDs differ by up to 13 dB.
EVM degradation limits apply after accounting for noise floor contributions relevant to test scenario conditions as opposed to the signal chain per se.
Receive Performance Aggregate Analog L-Band Downlink Input through DM Port EVM degradation through DIFS downlink signal chains, aggregate downlink input through DM port, shall be limited as follows:
1. Where L-Band IF conversion is employed, EVM degradation from the IFC L-Band input to the DM sink port shall be limited to ≤ 2% in an RSS sense.
Where direct RF conversion is employed, EVM degradation from the RFC RF input to the DM sink port shall be limited to ≤ 2.8% in an RSS sense.
EVM degradation limits shall apply to 16-APSK modulation.
EVM degradation limits shall apply to all signals where DIFI Standard “Usable Bandwidth” does not overlap.
EVM degradation limits shall apply to adjacent waveforms, where usable bandwidth abuts, to carriers of PSD discrepancy up to 13 dB.
EVM degradation limits apply after accounting for noise floor contributions relevant to test scenario conditions as opposed to the signal chain per se.
Aggregate Analog L-Band Downlink Input through Aggregate Analog L-Band Modem Output The following requirements apply to all signal paths from IFC aggregate analog downlink inputs through one or more cascaded Digital IF Dividers to IFC aggregate analog modem outputs via the DIFI switch fabric. These requirements allocate a portion of the MIL-STD-188-164 Reception Function performance requirements to DIFS, with the balance reserved for the SATCOM terminal Receive Subsystem providing the downlink to DIFS and to the receive portion of any LBSS fed from DIFS.
Receive Instantaneous Bandwidth All DIFS aggregate analog downlink input to aggregate analog modem output receive signal paths shall be capable of supporting a maximum instantaneous bandwidth of no less than 1 GHz. Instantaneous bandwidth is defined in Paragraph 3.1.2.3.
Receive Gain The net per-carrier receive digital gain of the aggregate analog downlink input to aggregate analog modem output signal paths shall be 0 dB. Analog gain adjustment for equipment alignment is specified in Paragraph 3.7.3.
Receive Level Stability The level stability of any receive carrier traversing an DIFS aggregate analog downlink input to aggregate analog modem output signal path shall not be degraded by more than 1 dB peak-to-peak in any 24 hour period (see MIL-STD-188-164 Paragraph 4.3.11).
Receive Frequency Conversion Accuracy The DIFS receive frequency conversion accuracy of the aggregate analog downlink input to aggregate analog modem output signal paths shall be within ±1 kHz of the intended value for all carriers (see MIL-STD-188-164 Paragraph 4.3.4).
Receive Phase Linearity The DIFS receive phase linearity of the aggregate analog downlink input to aggregate analog modem output signal paths shall be no greater than 50% of that allowed by MIL-STD-188-164 Paragraph 4.3.6.
Receive Amplitude Response The DIFS receive amplitude response of the aggregate analog downlink input to aggregate analog modem output signal paths shall not exceed the following (see MIL-STD-188-164 Paragraph 4.3.6):
a. 0.5 dB peak to peak over any 10 MHz segment across the instantaneous bandwidth.
b. 1.0 dB peak to peak over any 120 MHz segment, or any smaller segment, across the instantaneous bandwidth (10 MHz < segment < 120 MHz).
c. 2.0 dB peak to peak over 1.0 GHz.
Receive Spectral Purity The contribution of the DIFS to the spectral purity of any receive carrier traversing any aggregate analog downlink input to aggregate analog modem output signal path shall be as specified in Paragraphs 3.2.1.1.2.7.1 through 3.2.1.1.2.7.3.
Receive Spurious Output Receive spurious outputs produced by DIFS aggregate analog downlink input to aggregate analog modem output signal paths shall meet the requirements of MIL-STD-188-164 Paragraphs 4.3.9.1 and 4.3.9.2 with a 6 dB margin when measured at the DIFS aggregate analog modem output under the conditions of MIL-STD-188-164 Paragraph 4.3.9.3(b). The narrowest bandwidth of interest shall be 128 kHz.
Receive Intermodulation Products The PSD of any intermodulation product at the DIFS aggregate analog modem output shall be such that there is less than a 0.1 dB increase in the DIFS noise floor when receiving an aggregate analog downlink input with signal power equivalent to the downlink power delivered to DIFS by the MET when receiving the maximum power flux density specified in MIL-STD-188-164 Paragraph 4.3.2.2.
Receive EVM EVM degradation through DIFS downlink signal chains, aggregate downlink input through aggregate L-Band modem output, shall be limited as follows:
1. Where L-Band IF conversion is employed, EVM degradation from the IFC L-Band input to the aggregate L-Band modem output shall be limited to ≤ 2.8% in an RSS sense.
Where direct RF conversion is employed, EVM degradation from the RFC RF input to the aggregate L-Band modem output interface shall be limited to ≤ 3.4% in an RSS sense.
EVM degradation limits shall apply to 16-APSK modulation.
EVM degradation limits shall apply to all signals where DIFI Standard “Usable Bandwidth” does not overlap.
EVM degradation limits shall apply to adjacent waveforms, where usable bandwidth abuts, to carriers whose PSDs differ by up to 13 dB.
EVM degradation limits apply after accounting for noise floor contributions relevant to test scenario conditions as opposed to the signal chain per se.
Communication Carriers The DIFS shall operate as specified herein when supporting from one up to [THRESHOLD] 64 carriers [OBJECTIVE] 128 carriers Cybersecurity The design of the DIFS shall not preclude Risk Management Framework (RMF) authorization in accordance with (IAW) Department of Defense Instruction (DODI) 8510.01.
General The DIFS Security Categorization is {(Confidentiality, Moderate), (Integrity, Moderate), (Availability, Moderate)}. When fielded, the DIFS will generate and process Controlled Unclassified Information (CUI). The DIFS does not create or process Personally Identifiable Information (PII).
Security Controls The DIFS shall incorporate technical security controls selected in accordance with CNSSI 1253 from NIST SP 800-53 as required for the security categorization specified in Paragraph 3.2.1.4.1. Note that the management, personnel, and operational controls required by CNSSI 1253 are also applicable to the DIFS but are non-technical in nature and therefore are not within the scope of this specification.
Information Technology Products All Ethernet switches and other network components cybersecurity requirements will adhere to the vendor Security Technical Implementation Guides (STIG) program managed by the Defense Information Systems Agency (DISA). To meet cybersecurity requirements, all DIFS information technology products must comply with the DoD Security Requirements Guide for the product class. Products not covered by a STIG must enter the vendor STIG program. Interoperability requirements will be guided by the Unified Capabilities Requirements (UCR) document and enforced through vendor compliance via contractual provisions. Equipment employing operating systems that are no longer supported (e.g. Windows 10 and prior versions) shall not be provided.
Trade Agreement Act (TAA) Compliance The countries of origin for all products incorporated into DIFS shall be in accordance with Federal Acquisition Regulation (FAR) Clause 52.225-5.
Information Technology Standards Information technology standards required by this specification are compliant with the DISR. Where the contractor, through the systems engineering process, identifies a derived requirement for which information technology standards exist, only those standards identified in the DISR shall be selected. Selection of an information technology standard not approved by the DISR, where an alternate DISR standard exists, shall require explicit approval from the Government. Note that DISR standards requirements for protocols and data formats that are transparently transported by the DIFS, are not applicable to the DIFS.
Life Expectancy The DIFS design and implementation shall support an expected useful life of 15 years under continuous operation.
Item Turn-On After exposure to the conditions specified in Paragraph 3.2.5.1, with no electrical prime power applied, the DIFS shall meet the performance requirements of this specification within 30 minutes after turn-on.
Physical Characteristics General The contractor shall develop two DIFS physical configurations:
1. [THRESHOLD] A configuration that incorporates all DIFS equipment into one or more equipment racks. [OBJECTIVE] A configuration that incorporates all DIFS equipment into one equipment rack.
1. [THRESHOLD] A configuration that incorporates all DIFS equipment except for the IFCs and protection switching means into one or more equipment racks. [OBJECTIVE] A configuration that incorporates all DIFS equipment except for the IFCs and protection switching means into one equipment rack. The IFCs and protection switching means shall be configured for rack mounting in environmentally controlled enclosures in or near the antenna.
Equipment Racks Equipment racks shall meet the following requirements:
1. Equipment racks to be installed within the EEB shall be designed for mounting to a raised floor and shall accept cooling air through the bottom of the rack. Exterior dimensions and mounting holes of racks to be mounted in the EEB shall be IAW C-E LCMC drawing A3274102 to the extent practicable.
1. All racks shall be secured to prevent tipping. Heavier equipment shall be mounted near the rack bottom where practicable.
1. Racks joined or grouped together shall be mechanically attached to adjoining racks and shall be of the same height. The attachment means shall not electrically isolate the adjoining racks. The attached racks shall be easily removable for addition or reduction of rack quantities.
1. Dimensions for equipment, enclosures, internal clearances, and equipment mounting holes shall conform to Section 4 of EIA-310. Blank panels shall be provided for all locations where DIFS components are not installed.
1. All racks shall include “nut clips,” which allow frequent removal of chassis from racks without stripping screw holes in the rack and ease physical alignment of assemblies.
Individual racks shall include a grounded front-mounted “banana” jack for connection of an electrostatic discharge (ESD) wrist strap.
A minimum of one duplex 120 VAC, 20 ampere convenience outlet shall be located in the lower portion of each equipment rack. The outlets shall be protected by Ground Fault Circuit Interrupters (GFCIs). Rack convenience outlets shall not be powered from the same circuit as the mission equipment in the rack.
Each equipment rack shall include a label, located at the top of the rack, indicating the following:
Unit number of the rack assembly Nomenclature of the rack assembly (where applicable) Description or informal name of the rack assembly Graphical depiction showing the unit number, name and location of each equipment module installed or installable in the rack assembly.
Equipment racks installed in the EEB shall be provided with rear doors equipped with latches. Removal of fasteners shall not be required to open the rack doors.
Fasteners and slides shall be constructed from corrosion resistant materials.
Rack grounding requirements are specified in Paragraph 3.3.2.3.2.
Equipment Modules All electronic equipment shall be of unitized construction for individual drawer type mounting and shall use standard 19-inch panels. To the maximum extent practicable, removable items shall be equipped with captive hardware. Slide rails shall be used for all rack-mounted equipment to facilitate access to components. To the maximum extent practicable, slide rails and mounting hardware shall be common throughout the DIFS. Components that do not have provisions for mounting slide rails shall be provided with slide rail equipped mounting trays.
Interconnecting Cables Interconnecting cables and connectors shall be arranged so that cabling is concealed within the equipment rack when equipment is installed (except for equipment with front-panel connectors), and so that equipment may be pulled out of the rack for inspection and maintenance. Cable retractors shall be provided. Any inter-rack cabling from a front-panel connector, unless for temporary testing purposes, shall go through an interface panel.
Weight The weight of the DIFS shall be such that the floor loading of individual racks shall not exceed 250 pounds per square foot. The weight of a single chassis shall not exceed the two-person lifting limits of Table 3-2 without explicit Government approval.
Reliability To minimize unscheduled corrective maintenance, the calculated Mean Time Between Failures (MTBF) for the DIFS shall be no less than 15,000 hours. Calculations shall be IAW MIL-HDBK-217 or Telcordia SR-332. For the purposes of calculating MTBF, DIFS shall include 18 full duplex IFCs, 18 CDs, all required TMDE and 128 narrow-band switch fabric ports populated with SFP+ modules, and sufficient switch fabric ports populated with QSFP28 modules to interconnect all DIFS hardware. All failures requiring corrective maintenance shall be included in the calculations.
System Availability The DIFS shall achieve an inherent availability (Ai) of no less than 0.9998 through conservative design, high reliability components and redundancy. The specified availability shall be achieved for all configurations and all equipment complements. Failures to be included in calculating availability shall be all hardware malfunctions that result in an interruption of one or more traffic signals or degradation of one or more traffic signals below the performance levels specified herein. For the purpose of calculating availability, hardware malfunctions resulting in momentary traffic signal interruptions of less than 400 milliseconds (ms) shall not be classified as failures. In assessing availability, the DIFS shall be assumed to be in its routine operational configuration, performing as specified herein, and operated by personnel as defined in Paragraph 3.6.
Reserved Maintainability Mean Time to Repair (MTTR) At the Field Maintenance Level (formerly, unit and direct support maintenance levels), the MTTR shall not exceed 30 minutes, and the Maximum Corrective Maintenance Time (MCMT) shall not exceed 90 minutes at the 95th percentile of the repair or corrective maintenance distribution times (Mmax).
Fault Detection and Isolation Definitions
1. A Lowest Replaceable Item (LRI) is defined as the lowest level DIFS component that can be removed and replaced on-site by Field Maintenance Level personnel, as defined in Paragraph 3.6. LRIs include but are not limited to fuses, circuit breakers, indicator lamps, modules, rack-mounted components, switches, cables, removable batteries, and hot-swappable components.
A Depot Lowest Replaceable Item (DLRI) is defined as the lowest level DIFS component that can be removed and replaced on-site by depot level personnel. DLRIs will be identified within the Maintenance Allocation Chart (MAC) with a remark annotating that on-site replacement/repair is performed by depot level personnel. Items in this category include items beyond the capabilities of personnel as defined in Paragraph 3.6.
Requirements The on-line Built-in Test (BIT) and Built-in Test Equipment (BITE) shall detect 95 percent of all equipment failures occurring during the service life. A minimum of 95 percent of all detected faults shall be isolated to an ambiguity level of two LRIs and/or DLRIs, and a minimum of 90 percent of all detected faults shall be isolated to an individual LRI or DLRI. All detected and isolated faults shall be reported to the DMASS. All detected faults that are isolated to an ambiguity group of more than one LRI and/or DLRI shall be isolated to one LRI or DLRI using troubleshooting instructions in the technical manual.
Use of Known-Good Spares for Fault Isolation The troubleshooting instructions provided by the technical manual shall not require swapping (physical removal and replacement) of LRIs and DLRIs with known good spares to perform fault isolation unless explicitly approved by the Government. If swapping of LRIs and DLRIs with known-good spares is prescribed by the technical manual, a means shall be provided to test the spare LRIs and DLRIs at the Field Maintenance Level to ensure that they are in a condition suitable for return to retail stock. Such test procedures shall be documented within the technical manual, and any resources needed to perform the tests shall be provided on-site.
Maintenance Design The DIFS design shall incorporate the following maintenance design provisions:
1. Modular construction shall be utilized to facilitate maintenance, to ensure commonality of replacement parts, and to reduce overall replacement and maintenance costs.
1. Reserved.
1. All equipment requiring metrology laboratory calibration shall be easily removed for calibration. The requirement for metrology laboratory calibration shall be eliminated wherever practicable. Calibration cycles for equipment requiring metrology laboratory calibration shall be no less than two years.
1. All incandescent indicator lamps, fuses, fans, air filters, slides, mounting hardware shall be replaceable at the Field Maintenance Level using common hand tools. Light emitting diode (LED) indicators shall be used in place of incandescent indicator lamps wherever practicable.
1. Test points, sample ports, tuning and critical adjustments shall be readily accessible. Wherever practicable, measurements, tuning and adjustments shall not require removal of equipment covers.
1. Wherever practicable, Type N connectors shall be provided for RF interfaces requiring frequent connection and disconnection of test cables.
This is the start of the file's text. The full file is on GovTribe.
File details come from the government source that posted it. Updated .