Technical Requirements GRIMCO RMAC 25-01.pdf
PDF 183 KB Posted
- Attached to
- Two (2) GRIMCO NH30-2 Hydraulic Presses
- Solicitation number
- W31P4Q-25-Q-0012
About this file
This document is a Technical Requirements document for a federal contract opportunity to procure two GRIMCO NH30-2 Hydraulic Presses for the US Army AMRDEC (Army Materiel Research, Development and Engineering Command) at Redstone Arsenal. The specific equipment requirements include two 30-ton manual hydraulic presses with heated platens (18.5" x 12.5"), two heavy-duty floor stands, two sets of spacers, four Omega CN 7200 controllers, and associated crating. Technical specifications mandate 30-ton force capacity, 24" daylight, heated platens capable of 500°F, 208 Volt single-phase power, and a machine footprint within 6.5 x 6.5 feet.
The solicitation (Number W31P4Q-25-Q-0012) is a sole-source requirement with a response deadline of 3:00 PM CST on 17 April 2025. Electronic quotes must be submitted to jimmy.w.creech.civ@army.mil. Evaluation factors include technical capability, price, and delivery. The items will be delivered to Building 5217, Room 111 at Mills Road, Redstone Arsenal, AL 35898. Payment will be processed via Wide Area Workflow, with all shipping costs included and FOB Destination to Redstone Arsenal, Alabama.
View the file
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
RMAC TECHNICAL REQUIREMENTS
1.0 Description of Requirement:
The contractor shall provide the following items as specified in the table below:
Item Number Part Description Qty
NH30-2
30-ton manual hydraulic press with heated platens, platen size 18.5” x 12.5” 2
NH30-2 FS NH30-2 Heavy Duty Floor Stand 2
NH30-2 Spacers Set of 3 spacers for daylight reduction two piece 2", one piece 4" 2
NH30-2 Controller Omega CN 7200 (Controller Top and Bottom Platen) 4
N/A Crating- Added for press with stand, domestic, commercial destination. 2
Additionally, this equipment must meet the requirements stated below:
• 30-ton force capacity
• 24” daylight
• Heated platens with a minimum heating capacity of 500°F
• Electrical service requirements 208 Volt Single Phase Power
• Machines footprint must fit within a 6.5-feet x 6.5-feet space
• Semi-Automatic Control: Press automatically opens at end of cycle. Includes adjustable cure timer and solenoid dump valve.
• Digital force gauge, high accuracy
• Press Frame constructed of carbon steel plate with one vertically mounted single up acting cylinder operating at 5000 PSI maximum. This cylinder pushes up the middle bolster with one daylight between the middle and top platens. The platens are mounted on bolster plates. Plate work area of 12.5" X 18.5" between post left to right and front to back.
• Four(4) guide rods which are lubricated and threaded allowing for adjustment of the daylight.
• Each Press will have two electrically heated and manual cooled platens, 4500 watts each and one heat zone each will operate up to 600 Degrees Fahrenheit. Platens of carbon steel construction, precision ground to .001 per/ft with cartridge, and insulation between the platen and bolster plates.
• Hydraulic system consisting of a two-stage manual pressure pump. The low pressure will supply high volume for rapid movement of the ram. The high-pressure stage of the pump will supply the volume of hydraulic fluid needed to reach the desired pressures.
2.0 Travel:
Travel is not required in the performance of this contract.
3.0 Deliverables:
RMAC TECHNICAL REQUIREMENTS
The above items shall be delivered to the following:
US ARMY AMRDEC
RDMR-WDA-MPA (Attn.) Greg Sivley or Jennifer Richman Building 5217, Room 111 Mills Road, Redstone, Arsenal, AL 35898 256-313-8788
File details come from the government source that posted it. Updated .