Techincal Exhibit 1 Specifications for Evaluation Submission Sheet Contender Vessels.pdf

Submission for Brand Name or Equal

(Required for Submission: See SF1449, FAR 52.212-2 and combined synopsis solicitation for Buy Terms)

Technical Exhibit #1: Specifications for Evaluation and Submission Sheet

Vendor must fill out Company’s name, POC, UEI, Date

Company Name:

POC:

Signature of Vendor:

Date:

UEI:

Failure to submit this a complete submission sheet with vendor’s signature will be result in a not acceptable rating.

Line Item

Quantity

& Unit of

Measure

IN EACH

Exact Brand Name and Equal FLETC requires a 30-foot vessel with additional options to ensure consistent and uniformity with current FLEET and Training Standards established.

*Vendor’s Name Submission-Please

Read Provision 52.211-6 & all buy terms) Any alternate brand name requires Specification Sheet. Vendor must make comments below for each specification listed. Alternate Brand

Name must be listed for comparison and Vendor is required to state how it is equal. Any blank responses will result in an “Not Acceptable Evaluation”

Technical

Customer

Evaluation

(Acceptable or Not

Acceptable)

2 each Provide Brand Name and Model number

Thirty Foot Contender (30T) or equal

Provide Brand Name/alternate and Model number. Specification sheet must be attached. Vendor must submit brochure and other supporting documents to demonstrate specification can be met for any alternate brand names.

Specifications salient characteristics All specifications must be equal to the following specifications and/or salient characteristics presented

One-year complete systems warranty a ten-year structural hull and deck warranty

Delivery must be within 6 months of award date

Maximum Length Overall (LOA): thirty five (35)ft.

Minimum Length Overall (LOA): thirty two (29)ft

Min/Max Beam: ten- (9 to 10) foot

Min/Max Draft: 22 - 24 (inches)

Hull Design: Deep “V” with minimum 24-Degree deadrise Minimum

Fuel Capacity: minimum 250 Gallons

Min Horsepower Rating: 600 hp

Power: Twin Yamaha F300 counter rotating outboard engines with Yamaha electronic controls and electric steering. (FLETC only uses Yamaha engines, required due to PM and repair capabilities) All other brand name engines will not be acceptable.

manufactured primarily from fiberglass reinforced plastic (FRP) commonly known as fiberglass

VinyLester resin in the entire hull and upper deck.

resin infusion process to provide a superior strength to weight ratio longitudinal stringers should be of a structural grid design that is infused simultaneously with the hull to create a single monolithic part no Employ wood construction in the upper deck stringers/structural grid should be tied into the stern of the vessel and bonded to the hull a stepless deep “V” design full transom with transom door and incorporate a dive platform. Note: it cannot be an “add on” type bracket or platform. Must be molded into hull.

thru-hull fittings and drains must be chrome on bronze or stainless steel fuel system Minimum three aluminum fuel tanks with the appropriate fuel manifold and water separating fuel filters.

Non-skid deck and cockpit

Fixed Back Leaning Post with folding foot rest and four cupholders.

Anchor and anchor line storage locker in the bow of the vessel

Integrated Bow Rail that is flush with the Gunnel

Minimum Nine pop up cleats (9)

Below deck dry storage lockers with cover gaskets

LED cockpit lighting

Console mounted recessed electronics box with a clear cover.

Trim Tabs using Kiekhaefer pumps and hydraulic rams

International Navigational lighting

Minimum of Three GP 27 marine batteries with EGIS battery switches

Center Console Layout

Garmin EmpirBus digital switching.

GARMIN is the only approved system used to meet the Federal Training Standards established by FLETC and Partner Organizations. All other systems will not be acceptable.

Minimum (2) 2000 Gallons per hour(GPH) bilge pumps on auto switches

Lilly brand Kingston Gray hull with light gray interior Gel-coat. Any other brand shade must match to ensure uniformity for FLETC. Vendor must provide proof for color match to be considered acceptable for this specification.

Aluminum T-Top with Hand rail, Four Spreader lights (4), Anchor Light- Masthead light, Antenna Pads for VHF and GPS antennas and a separate arch for the radome

Raw water washdown system

One red led light mounted to underside of T-top

Aluminum radar pad on top

Aluminum blue light pad on top

High speed compass

Tilted element thru hull transducer

Garmin GPSMAP 8616XSV with Navionics part# 010-02093-5. GARMIN is the only approved system used to meet the Federal Training Standards established by FLETC and Partner Organizations. All other systems will not be acceptable

Garmin Fantom Radome 18x part# 010- 02584-00. GARMIN is the only approved system used to meet the Federal Training Standards established by FLETC and will not be acceptable

Garmin GPS/Heading Sensor part# 010- 02316-10. GARMIN is the only approved system used to meet the Federal Training Standards established by FLETC and will not be acceptable

Standard Horizon GX6000 with an antenna VHF radio

AMERITrail Model # Model # AS2830TPB Aluminum double axle trailer with torsion axles, LED lights, stainless hardware, aluminum crossmembers and a matching spare tire. Alternate brand names/models are acceptable.