TECH TRAILER C.D 00554 12.2024.docx

TECH TRAILER

PGC 00554

PURCHASE ORDER TEXT (SECTION C):

GLOVES, RUBBER, INDUSTRIAL, BLACK

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT:

http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.

RD003, COVERED DEFENSE INFORMATION POTENTIALLY APPLIES

RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES

GLOVES, RUBBER, INDUSTRIAL, BLACK

MAKE IN ACCORDNACE WITH NU PD 32066B DATED 8 FEBRUARY, 2023.

TYPE III, STYLE I, 18 INCHES IN LENGTH

NOTE: THE MATERIAL FOR TYPE III SHALL BE NEOPRENE RUBBER.

NO SHADE REQUIRED.

NO PATTERN DATE.

Interim Changed to NU-PD-32066B IAW Document 8188067;

CONTRACTOR'S INSPECTION SYSTEM SHALL

REFLECT THE REQUIREMENTS SPECIFIED IN

ISO/ANSI 9000 OR ANY OTHER DOCUMENT

INCLUSIVE OF MILITARY SPECIFICATIONS

OR STANDARDS WHICH PROVIDE AN ADEQUATE

LEVEL OF PROTECTION.

ACCEPTABILITY OF LOTS WILL BE DETERMINED

BY THE USE OF "SAMPLING PROCEDURES AND

TABLES FOR INSPECTION BY ATTRIBUTES",

ASQ ZQ.4.

NOTE: UNIVERSAL PRODUCT CODE INFORMATION:

THE GOVERNMENT ASSIGNED UNIVERSAL PRODUCT CODE (UPC)

MUST BE PLACED ON ALL SHIPPING CARTONS ON WHICH THE

NSN APPEARS.

THE INSPECTION LEVELS, EXPRESSED IN DEFECTS PER HUNDRED

UNITS FOR VISUAL AND DIMENSIONAL EXAMINATION, SHALL BE

AS FOLLOWS:

AQL'S

.......................INSPECTION LEVEL....MAJOR..... TOTAL

VISUAL DEFECTS........ II...................1.0........4.0

DIMENSIONAL DEFECTS....S-3...................-.........2.5

THE INSPECTION LEVEL SHALL BE S-1, WITH AN AQL OF

2.5 DEFECTS PER 100 UNITS.

INSPECTION OF SUPPLIES SHALL BE IN ACCORDANCE WITH FAR PART 52.246-2 STANDARD INSPECTION.

ADDITIONAL INFORMATION FOR MIL-STD-105E:

MIL-STD-105E, dated 10 May 1989, is hereby canceled.

Future acquisitions may refer to: MIL-STD-1916, "DoD Preferred Methods for Acceptance of Product," or ANSI/ASQ Z1.4, "Sampling Procedures and Tables for Inspection by Attributes."

Users are cautioned to evaluate these documents for their particular application before citing it as a replacement document.

(Copies of MIL-STD-1916 are available online at http://assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)

(Copies of ANSI/ASQ Z1.4 are available online at www.asq.org or ASQ Distribution Center, 5131 S. Third Street, Milwaukee, Wisconsin 53207-6028.)

INSPECTION TEXT (SECTION D):

RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT

PRES/PACK LEVELS C/C IAW ASTM-D-3951.

TYPE II SHELF LIFE (60 MONTHS)

1 PR/BAG (HEAT SEALED POLYETHYLENE)

24 PRS SHALL BE PACKED IN FIBERBOARD SHIPPING

CONTAINERS, STYLE RSC, TYPE CF,

CLASS DOMESTIC, VARIETY SW, GRADE 275,

WITH LINER, VARIETY DW, GRADE 200.

AS A MINIMUM ITEMS SHALL BE PACKED IN A SNUG FITTING FIBERBOARD SHIPPING CONTAINER CONFORMING TO ASTM-D-5118, TYPE CF, STYLE RSC, GRADE 275 or ECT 44, VARIETY SW, CLASS DOMESTIC, WITH A DOUBLE WALL LINER. ANY COMMERCIAL CLOSURE METHOD CITIED IN ASTM-D-1974 IS ACCEPTABLE EXCEPT STAPLING.

PACKAGING SHALL BE AS PER ASTM-D-3951, MIL-STD-129R WITH CHANGE 3, MIL-STD-147E WITH CHANGE 2.

LOT NUMBERING SHALL BE IN ACCORDANCE WITH MIL-STD-129 R WITH CHANGE NOTICE 3 and DLA TROOP SUPPORT C&T AQAR dated 1 August 2021.

RS062: Shelf life requirement RS001 for a TYPE 2 (CODE 9) item with a shelf life of 60 month (extendable to 12 months) applies to this item.

THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL AND

QUALITY REQUIREMENTS FOUND ON THE WEB AT: http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx.

FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS.

FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.

THE INSPECTION LEVELS, EXPRESSED IN DEFECTS PER HUNDRED

UNITS FOR VISUAL AND DIMENSIONAL EXAMINATION, SHALL BE

AS FOLLOWS:

THE INSPECTION LEVEL SHALL BE S-1, WITH AN AQL OF 2.5 DEFECTS PER 100 UNITS.

image1.png