TECH DATA US NAVY WOOL BLUE 3346.pdf

CLOTH, WOOL SERGE, TYPE I, CLASS 5, SHADE Blue 3346

RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN

RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS

(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA

MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT:

http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx

FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE

SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE

ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE

APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON

REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.

MOTHPROOFED, SPONGED

. STANDARD SAMPLE IS IDENTIFIED AS PIECE NO. 10164 AND IS AVAILABLE AND

APPLLICABLE FOR SHADE, FINISH, AND COLORFASTNESS.

ADDITIONAL INFORMATION FOR PPP-P-1132C:

PPP-P-1132C PACKAGING OF WOOLEN, WORSTED

. AND WOOL BLEND, SYNTHETIC FI-

. BER, AND CTN FABS, 10/31/83;

. VALID NOT 2, 5/8/96.

PPP-P-1132 HAS BEEN CANCELLED. USE ASTM-D-3951-

STANDARD PRACTICE FOR COMERCIAL PACKAGING.

COPIES MAY BE OBTAINED FROM THE AMERICAN SOCIETY

FOR TESTING AND MATERIALS, 100 HARBOR DRIVE,

WEST CONSHOHOCKEN, PA. 19428.

REFERENCE MIL-DTL-823M DATED 2 SEPT 2020

ADDITIONAL INFORMATION FOR MIL-I-45208:

NOTE: MIL-I-45208 HAS BEEN CANCELLED AND REPLACED BY THE FOLLOWING:

INTERNATIONAL STANDARDS ISO 9001:2008

OR AMERICAN SOCIETY FOR QUALITY ASQ 2008 VERSION.

(ref. T1286 )

FED-STD-4 Glossary of Fabric Imperfections has been superseded by ASTM D 3990 Standard Terminology Relating To Fabric Defects

No information follows

ADDITIONAL INFORMATION FOR FED-STD-191:

FED-STD-191A NOTICE 7, DATED AUGUST 9, 2000 IS HEREBY INACTIVE FOR NEW

DESIGN. WHEN NOT USING FED-STD-191, SEE INTERIM CHANGES TO END ITEM

SPECIFICATION FOR REPLACEMENT ASTM.

INTERIM CHANGES TO FED-STD-191A:

TEST METHOD 5202, PARA. 5.3, DELETE FIRST SENTENCE AND SUBSTITUTE: "THE

SPECIMEN SHALL BE CLAMPED FIRMLY, WITH ONE END FLUSH WITH THE OUTER EDGE

OF THE VISE, SUCH THAT ONE INCH OF SPECIMEN LIES WITHIN THE CLAMP AND ONE

INCH OF THE SPECIMEN EXTENDS BEYOND THE CENTER OF ROTATION (FACE OF THE

VISE), AND WITH THE LONG EDGE PARALLEL TO THE FACE OF THE DIAL PLATE".

TEST METHOD 5309.1 ABRASION RESISTANT OF TEXTILE WEBBING. PAGE 1, PARA

4.1.2,LINE 4: DELETE "B-97" AND SUBSTITUTE "B-91".

THE FOLLOWING METHODS ARE IDENTIFIED AS SPECIFYING OZONE DEPLETING

SUBSTANCES: 1100, 1200, 1240, 1400, 1410, 1500, 1510,1520,1530, 1540, AND

1550. PARA 5.1 OF THESE TEST METHODS REQUIRE THE USE OF 1,1,1-

TRICHLOROETHANE, ALCOHOL OR ETHER. 1,1,1-TRICHLORETHANE IS AN OZONE

DEPLETING SUBSTANCE (METHYL CHLOROFORM) AND IS THEREFORE PROHIBITED. THE

USE OF EITHER ALCOHOL OR ETHER IS REQUIRED WHEN THESE METHODS ARE IN

BASIC OR ANY REFERENCED DOCUMENT.

METHOD 5202, STIFFNESS OF CLOTH, DIRECTIONAL; CANTILEVER BENDING METHOD.

PAGE 2, PARA. 5.3 DELETE FIRST SENTENCE AND SUBSTITUTE WITH THE

FOLLOWING: "THE SPECIMEN SHALL BE CLAMPED FIRMLY, WITH 1 END FLUSH WITH

THE OUTER EDGE OF THE VISE, SUCH THAT 1" OF THE SPECIMEN LIES WITHIN THE

CLAMP AND 1" OF THE SPECIMEN EXTENDS BEYOND THE CENTER OF ROTATION (INNER

FACE OF THE VISE) AND WITH THE LONG EDGE PARALLEL TO THE FACE OF THE DIAL

PLATE."

METHOD 5556.1, MOBILE LAUNDRY EVALUATION FOR TEXTILE MATERIALS, PAGE 5,

PARA. 5.2.2, LINE 8: DELETE SENTENCE BEGINNING WITH "THE SPECIMENS AND

BALLAST" IN ITS ENTIRETY AND SUBSTITUTE WITH THE FOLLOWING: "THE

SPECIMENS AND BALLAST SHALL BE SEPARATED, OPENED TO FULL WIDTH AND PLACED

IN A PRE-HEATED DRYER HAVING A STACK TEMPERATURE OF 140-180 DEG. F. THIS

TEMPERATURE RANGE CORRESPONDS TO A SETTING OF "HIGH" ON THE TEMPERATURE

INDICATOR ON THE DRYER. DRYING SHALL CONTINUE FOR 45-60 MINUTES OR

UNTILSAMPLES ARE DRY IN A ROTATING TUMBLE DRYER."

PAGE 5, PARA. 5.2.3, LINE 8: DELETE SENTENCE BEGINNING WITH "THE

SPECIMENS AND BALLAST" IN ITS ENTIRETY AND SUBSTITUTE WITH THEFOLLOWING:

"THE SPECIMENS AND BALLAST SHALL BE SEPARATED, OPENED TO FULL WIDTH AND

PLACED IN A PRE-HEATED DRYER HAVING A STACKTEMPERATURE OF 140-180 DEG. F.

THIS TEMPERATURE RANGE CORRESPONDS TO A SETTING OF "HIGH" ON THE

TEMPERATURE INDICATOR ON THE DRYER. DRYING SHALL CONTINUE FOR 35-40

MINUTES OR UNTIL SAMPLES ARE DRY."

METHOD 5931, ELECTROSTATIC DECAY OF FABRICS; DETERMINATION OF PAGE 1,

PARA. 3: AFTER NUMBER OF DETERMINATIONS ADD "PER SAMPLE UNIT". PAGE 1,

PARA. 4: DELETE "APPARTUS" AND SUBSTITUTE "APPARATUS". PAGE 1, PARA.

5.1, LINE 3: AFTER "AT" DELETE"APPROXIMATELY".

PAGE 2, PARA. 5.2, LINES 2, AND 5: AFTER "OF" ADD "+-". LINE 6: AFTER

"TO" ADD "+-".

PAGE 2, PARA. 5.3: DELETE IN ITS ENTIRETY AND SUBSTITUTE WITH THE

FOLLOWING:"5.3 MOUNT A SPECIMEN TIGHTLY ACROSS THE ELECTRODES, CENTERING

IT OVER THE SENSOR OPENING. THE SURFACE OF THE TEST SPECIMEN (BACK OR

FRONT) SHALL FACE THE SENSOR. RECORD (OPTIONAL) THE RESIDUAL CHARGE LEVEL

ON THE SAMPLE AS SEEN BY THE SENSOR, INCLUDING POLARITY.

NOTE THAT TEST SAMPLES WITH THE RESIDUAL CHARGE LEVELS OF LESS +500 VOLTS

YIELD THE BEST RESULTS. APPLY +5000 VOLTS TO THEELECTRODES FOR A PERIOD

OF 20 SECS. AT THE END OF THE 20 SECOND PERIOD, THE HIGH VOLTAGE (5000

VOLTS) SHALL BE TURNED OFF ANDTHE SPECIMENS IMMEDIATELY GROUNDED. THE

VOLTAGE BEHAVIOR OF THE SPECIMEN WITH RESPECT TO TIME SHALL BE PLOTTED ON

THE RECORDER. NOTE: IN SOME CASES, THE TEST EQUIPMENT WILL DISPLAY

VOLTAGE AND DECAY TIME INFORMATION AND A CHART RECORDER IS NOT

NECESSARY."

PAGE 2, PARA. 5.4, LINE 3: DELETE SENTENCE BEGINNING WITH "IF THE

SPECIMEN DID" IN ITS ENTIRETY.

PAGE 2, PARA. 5.5: DELETE PARAGRAPH IN ITS ENTIRETY AND SUBSTITUTE WITH

THE FOLLOWING: "RECORD THE MAXIMUM VOLTAGE LEVEL(INCLUDING POLARITY) AND

DECAY TIME TO 10% OF THE MAXIMUM VOLTAGE LEVEL ACHIEVED."

PAGE 2, PARA. 5.6, LINE 1: ADD THE FOLLOWING PRIOR TO 1ST SENTENCE:

"REVERSE VOLTAGE POLARITY REPEAT MEASUREMENT, ANDRECORD RESULTS."

PAGE 3, PARA. 6.6: DELETE PARAGRAPH IN ITS ENTIRETY AND SUBSTITUTE WITH

THE FOLLOWING: "THE AVERAGE TIME TO DECAY TO 10%OF THE MAX VOLTAGE SHALL

BE INCLUDED FOR EACH OF THE WARP & FILLING DIRECTIONS, AS WELL AS THE

OVERALL AVERAGE, FOR EACHFABRIC TESTED. THESE WILL BE OBTAINED BY

AVERAGING THE TEST RESULTS (ABSOLUTE VALUE OF) TOGETHER FOR BOTH

VOLTAGEPOLARITIES. UNLESS OTHERWISE STATED IN THE REQUIREMENTS DOCUMENT,

THE FABRIC SHALL BE CONSIDERED ACCEPTABLE IF THEAVERAGE MAXIMUM VOLTAGE

IN BOTH THE WARP AND FILLING DIRECTIONS IS LESS THAN 4000 VOLTS, AND THE

AVERAGE DECAY TIME (TO 10% MAXVOLTAGE) IS GREATER THAN 0.5 SECONDS IN

BOTH THE WARP AND FILLING DIRECTIONS. IT SHALL BE INDICATED WHETHER THE

FABRIC ISACCEPTABLE OR NON-ACCEPTABLE."

PAGE 3, PARA. 7.1, SECOND COLUMN, LINE 2: DELETE 406C AND SUBSTITUTE WITH

"406D".

AFTER PARA. 7.1, ADD THE FOLLOWING: "7.2 NOTE: IF THE MODEL 406D STATIC

DECAY METER, OR EQUIVALENT, IS USED, A CHART RECORDER ISNOT MANDATORY FOR

THE TEST."

(Ref. T0215)

INSPECTION OF SUPPLIES SHALL BE IN ACCORDANCE WITH FAR PART 52.246-2

STANDARD INSPECTION.

ADDITIONAL INFORMATION FOR MIL-STD-105E:

MIL-STD-105E, dated 10 May 1989, is hereby canceled.

Future acquisitions may refer to: MIL-STD-1916, "DoD Preferred Methods for Acceptance of Product," or ANSI/ASQ Z1.4, "Sampling Procedures and Tables for Inspection by Attributes."

Users are cautioned to evaluate these documents for their particular application before citing it as a replacement document.

(Copies of MIL-STD-1916 are available online at http://assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)

(Copies of ANSI/ASQ Z1.4 are available online at www.asq.org or ASQ Distribution Center, 5131 S. Third Street, Milwaukee, Wisconsin 53207- 6028.)

MIL-STD-129R w/CHANGE 2 - DEPARTMENT OF DEFENSE STANDARD PRACTICE

MILITARY MARKING FOR SHIPMENT AND STORAGE

DATED: 27 SEPTEMBER 2019

INTERIM CHANGES:

OMISSION OF MARKINGS ON EXTERIOR SHIPPING CONTAINERS OF ITEMS

IN THE DLA TROOP SUPPORT CLOTHING AND TEXTILE (C&T) DIRECTORATE:

THE NOMENCLATURE AND MANUFACTURER'S NAME (WHEN THE NAME IDENTIFIES THE

MATERIAL) SHALL BE OMITTED FROM ALL EXTERIOR SHIPPING CONTAINERS OF DLA

TROOP SUPPORT C&T ITEMS, REGARDLESS OF MODE OF SHIPMENT.

IF THE MANUFACTURER'S NAME DOES NOT IDENTIFY THE MATERIAL AS BEING

CLOTHING, IT MAY REMAIN. NSNS SHALL BE SHOWN ON ALL SHIPPING CONTAINERS

OF C&T ITEMS, THE PACKING LIST SHALL BE PLACED INSIDE THE LAST CONTAINER

TO BE LOADED FOR EACH SHIPMENT. THE WORDS "PACKING LIST HERE" SHALL BE

STENCILED, NOT HAND LETTERED, ON THE CONTAINER.

ADDITIONAL INFORMATION FOR MIL-STD-655D:

INTERIM CHANGES TO MIL-STD-655D:

PAGE 3, PARA 4.1, ADD "QUALITY LEVEL 7"

PAGE 5, TABLE I, UNDER QUALITY LEVEL"7", ADD

UNDER ENTIRE SAMPLE "7 POINTS PER 100 SQ.

YARDS", ADD UNDER INDIVIDUAL ROLLS "10 POINTS

PER 100 SQ. YDS."

(Ref. T0319)

ADDITIONAL INFORMATION FOR MIL-C-43665:

INTERIM SPECIFICATION CHANGES TO MIL-C-43665C:

PAGE 2, PARA. 3.2, LINE 2, AFTER "TABLE 1 "

INSERT "OR TABLE 1A",

PAGE 3, TABLE 1, DELETE "SODIUM (4,5-DICHLORO,

2-CHLOROMETHANE SULFONAMIDO) 3',4'

6',TRICHLORO) DISHENYL ETHER (SEE 6.3.2) 0.26

0.60".

PAGE 3, AFTER TABLE 1, INSERT THE FOLLOWING NEW

TABLE:

"TABLE 1A, MOTHPROOFING COMPOUND.

. % ON WEIGHT OF WOOL

. MOTHPROOFING COMPOUND MIN. MAX.

EDOLAN ETS BEFORE DRYCLEANING

*(3-PHENOXYPHENYL) METHYL

PLUS OR MINUS CIS/TRANS 3-(2-,2-

DICCHLOROETHENYL)2,2-

DIMETHYLCYCLORPPANECARBOXYLATE. 0.058 0.40

CIS/TRANS RATIO:MAX.55% PLUS OR--AFTER DRY-CLEAN

MINUS CIS AND MIN.PLUS OR

MINUS TRANS.(*PERMETHRIN) 0.029 0.40

PAGE 3,PARA.3.4, LINE 3, AFTER "3.2" INSERT

"TABLE 1".

PAGE 3, AFTER PARA. 3.4 INSERT NEW PARAGRAPH AS

FOLLOWS:

"3.4.1 PERCENT OF MOTHPROOFING COMPOUND. THE

PERCENTAGES OF MOTHPROOFING COMPOUND SPECIFIED

IN TABLE 1A SHALL BE BASED ON WEIGHT OF PURE

COMPOUND ON THE WOOL FIBER CONTENT WHEN TESTED

BY HIGH PERFORMANCE LIQUID CHROMATOGRAPH (HPLC)

METHOD, OBTAINABLE FROM BAYER CORP., ROCK HILL,

SC 29732 (SEE 4.2.2)".

PAGE 5, PARAGRAPH 4.2.2,TABLE 11,DELETE THE

FOLLOWING:

CHARACTERISTIC REQUIREMENT TEST

. PARAGRAPH METHOD

"SODIUM (4,5-DICHLORO

2-CHLORO-METHANE

SULFONAMIDO)3',4',6',

TRICHLORO) DIPHENYL ETHER 3.4 4.3.1 3/ 4/"

AND SUBSTITUTE THE FOLLOWING:

CHARACTERISTIC REQUIREMENT TEST

. PARAGRAPH METHOD

"EDOLAN ETS

*(3-PHENOXYPHENYL 3.4.1 HPLC 7/

METHYL PLUS OR MINUS CIS/TRANS

3-(2,2-DICHLOROETHENYL)

2,2-DIMETHYL-CYCLOPROPANECARBOXYLATE

CIS/TTRANS RATIO: MAX.55%

PLUS OR MINUS CIS AND MIN.

PLUS OR MINUS TRANS.

*(PERMRTHRIN)"

PAGE 5, PARAGRAPH 4.2.2, FOR CHARACTERISTIC

EDOLAN ETS,UNDER TEST METHOD COLUMN, ADD

FOOTNOTE "7"/,ADD NEW FOOTNOTE "8"/.

PAGE 6, PARAGRAPH 4.2.2, TABLE II.AFTER FOOTNOTE

"7/",ADD THE FOLLOWING:"8"/ THE SAMPLE SHALL

BE DRY-CLEANED FOR THREE CYCLES IN ACCORDANCE

WITH AATCC TEST METHOD 86 BEFORE DETERMINING

MOTHPROOFING COMPOUND CONTENT.

PAGE 6, PARA.4.2.2, TABLE 11, AFTER FOOTNOTE 6/,

INSERT "7/ HIGH PERFORMANCE LIQUID

CHROMATOGRAPHY (HPLC) TEST METHOD MAY BE

OBTAINED FROM BAYER CORP., ROCK HILL, SC 29732."

PAGE 6, PARAGRAPHS 4.3,4.3.1,4.3.1.1,4.3.1.2,

4.3.1.3,4.3.1.4,4.3.1.5 DELETE PARAGRAPHS IN

THEIR ENTIRETY WITH NO REPLACEMENT.

PAGE 7, PARAGRAPHS 4.3.1.6, 4.3.1.7, 4.3.1.7.1

DELETE PARAGRAPHS IN THEIR ENTIRETY WITH NO

REPLACEMENT.

PAGE 8, PARAGRAPHS 4.3.1.7.2, 4.3.1.8, 4.3.1.8.1

DELETE PARAGRAPHS IN THEIR ENTIRETY WITH NO

REPLACEMENT.

PAGE 9, PARAGRAPHS 6.3 2, 6.4, 6.5, 6.6 DELETE

PARAGRAPHS IN THEIR ENTIRETY WITH NO

REPLACEMENTS.

PAGE 11, DELETE FIGURE 1 IN ITS ENTIRETY WITH NO

REPLACEMENT.

TABLE II, UNDER TEST METHOD: DELETE "2015" AND

SUBSTITUTE "2015.3"

NOTE! MITTEN FF CONC. SUPPLIED BY CIBA-GEIGY

CORP. P.O. BOX 11422, GREENSBORO, NC 27409

EDOLAN ETS, SUPPLIED BY MILES INC.,MOBAY ROAD,

PITTSBURGH,PA.15205-9741.

ARE APPROVED MOTH PROOFING AGENTS FOR

MILITARY FABRICS.