Tech-Data-Swtpnts-CG-PGC02309R.pdf

TECH-DATA PGC02309 10/25/2021

NSN: 8415-01-436-8796

SWEATPANTS, COAST GUARD

CG/PD 15-22 DATED 1 JUL 2015

RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL

AND QUALITY REQUIREMENTS FOUND ON THE WEB AT:

http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx. FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON

REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.

RQ009: INSPECTION AND ACCEPTANCE AT DESTINATION.

THE SWEATPANTS SHALL BE MADE IN ACCORDANCE WITH

CG/PD 15-22 DATED 1 JUL 2015

THE FOLLOWING CHANGES APPLY TO CG 15-22:

paragraph 3.3 Design.: line 8, after “thermal heat transfer” add “or screen printing.

The orange portion shall match International Orange—chip 12197”.

Paragraph 3.4.1 Basic material,: delete “jersey” and substitute “fleece”.

COLOR CHIPS ARE AVAILABLE FROM SAE.org.

MIL-STD-129P, WITH CHANGE 4 - DEPARTMENT OF DEFENSE STANDARD PRACTICE MILITARY MARKING

FOR SHIPMENT AND STORAGE - DATED

19 SEPTEMBER 2007

INTERIM CHANGES:

OMISSION OF MARKINGS ON EXTERIOR SHIPPING CONTAINERS OF ITEMS

IN THE DLA TROOP SUPPORT CLOTHING AND TEXTILE (C&T) DIRECTORATE:

THE NOMENCLATURE AND MANUFACTURER'S NAME (WHEN THE NAME IDENTIFIES THE MATERIAL) SHALL

BE OMITTED FROM ALL EXTERIOR SHIPPING CONTAINERS OF DLA TROOP SUPPORT C&T ITEMS,

REGARDLESS OF MODE OF SHIPMENT.

IF THE MANUFACTURER'S NAME DOES NOT IDENTIFY THE MATERIAL AS BEING CLOTHING, IT MAY REMAIN. NSNS SHALL BE SHOWN ON ALL SHIPPING CONTAINERS OF C&T ITEMS, THE PACKING LIST SHALL BE PLACED INSIDE THE LAST CONTAINER TO BE LOADED FOR EACH SHIPMENT. THE WORDS

"PACKING LIST HERE" SHALL BE STENCILED, NOT HAND LETTERED, ON THE CONTAINER.

MIL-STD-147 IS HEREBY REINSTATED AS FOLLOWS:

MIL-STD-147E DEPARTMENT OF DEFENSE

16 MAY 2008 STANDARD PRACTICE

PALLETIZED UNIT LOADS

STANDARDS (COMMERCIAL)

ASME-MH1 American Society of Mechanical Engineers (ASME) Pallets, Slip Sheets, and Other Bases For Unit Loads, for construction of pallets.

TGI DATA:

INSPECTION AND ACCEPTANCE AT DESTINATION.

ADDITIONAL INFORMATION FOR ASL:

THE ACCEPTABLE SUPPLIER LISTING (ASL) AND QUALIFIED LABORATORY LISTING (QLL) ARE NO LONGER VALID DOCUMENTS AND WILL NOT BE PUBLISHED IN THE FUTURE. THE POINT OF CONTACT

FOR QUESTIONS PERTAINING TO LABORATORIES AND SUPPLIERS IS THE PROCUREMENT BUYER,

INDICATED IN THE SOLICITATION OR CONTRACT. QUESTIONS SHOULD BE PROVIDED IN WRITING TO

THE DESIGNATED BUYER.

CLAUSE 52.246-9P44 IDENTIFICATION OF QUALIFIED LABORATORY AND SOURCE SAMPLING APPLIES.

52.246-2, Inspection of Supplies - Firm-Fixed Price 52.209-4, Alt. I, First Article Approval - Government Testing

52.209-9019 (I09C25), REQUESTS FOR WAIVER OF FIRST ARTICLE TESTING REQUIREMENTS (SEP

2008) - DLAD

52.246-15 CERTIFICATE OF CONFORMANCE

52.215-9017 List of Documents, Exhibits, and other Attachments (Apr 2008) - DLAD

(a) This solicitation/award consists of the following documents, exibits, and other attachments:

(1) DLA Troop Support Clothing & Textiles Additional Quality Assurance Requirements dated October 2018, which has superseded DSCPM 4155.3, QUALITY SYSTEMS REQUIREMENTS, dated NOVEMBER 3, 1997.

(2) DLAD 5025.30, Defense Logistics Agency One Book, Quality Management Programs Process Chapter, Dated October 31, 2003.

52.246-9030 (E46C10), SHADE EVALUATION OF CONTRACTOR FURNISHED COMPONENTS (APR 2008) -

DLAD. SHADE SAMPLING IS APPLICABLE

CERTIFICATE OF QUALITY COMPLIANCE (COCQ)

ESTABLISHED DUE TO PREVIOUS, OR POTENTIAL NONCONFORMANCES

INDICATE COQC CLAUSE IS NECESSARY (FLAMMABILITY)

(Ref. T1750 - 9/11/06)

ADDITIONAL INFORMATION FOR COMMERCIAL AQL'S:

AQL'S FOR COMMERCIAL ITEM DESCRIPTIONS (CID'S):

VISUAL - GENERAL INSPECTION LEVEL II, AQL - 1.0

DIMENSIONAL - SPECIAL INSPECTION LEVEL S-2, AQL - 2.5

ACCEPTABILITY OF LOTS WILL BE DETERMINED BY THE USE

OF "SAMPLING PROCEDURES AND TABLES FOR INSPECTION BY ATTRIBUTES", ANSI/ASQC Z1.4

ADDITIONAL INFORMATION FOR ANSI/ASQC Z1.4:

NOTE: THE MOST RECENT VERSION OF THIS DOCUMENT SHOULD BE USED.

APPLICATION FOR COPIES SHOULD BE ADDRESSED TO:

AMERICAN SOCIETY FOR QUALITY

600 NORTH PLANKINTON AVENUE

MILWAUKEE, WISCONSIN 53203

(Ref. T0795 - May 17, 2006)

Packaging Data

PRES/PACK TO ASTM-D-3951

SHIPPING CONTAINER QUANTITY = 24

CARTONS SHALL BE STYLE RSC, GRADE 275,

VARIETY SW WITH DW LINERS, GRADE 275

RFID HANGTAG:

An RFID inlay shall be added to the barcode paper hang tag attached to each item.

Where the use of self-adhesive bar-code labels are authorized, the RFID inlay may be added to the self-adhesive label in lieu of a paper hang tag. All other contract barcode and hang tag requirements still apply.

The RFID inlay should be passive Gen2 with a frequency range between 860 and 960 MHz.

The RFID antenna should be Avery/Dennis AD222 or comparable with ISO/IEC 18000-C EPCglobal C1G2 Protocol and an EPC memory allocation containing a 96 bit EPC Number.

The data linking the EPC number to the NSN and quantity unit pack must be exportable to VIM/ASAP. The bar code of the EPC Number must be printed at the bottom of the tag along with the human readable version below the bar code.

In addition to defects applicable to the paper tag and barcoding element, the RFID tag shall be examined for the defects listed below:

RFID Inlay omitted RFID Inlay not secure RFID Inlay not laying flat when packaged RFID Inlay not readable with RFID scanner RFID Inlay or configuration not as specified

The manual "Item-Level Passive RFID Technology Manufacturer's Information Guide" provides guidance on RFID implementation and is available from the contracting officer.

252.211-7006 - RADIO FREQUENCY IDENTIFICATION (RFID) Required (ref. T8379; Nov. 08, 2006)

SIGNIFICANT NOTE - "PALLETIZATION IS REQUIRED FOR THESE SUPPLIES".

NOTE: THE FOLLOWING APPLIES TO ALL NON-MANUFACTURED WOOD PACKAGING MATERIALS:

"All Wood Packaging Material (WPM) acquired by DOD must meet requirements of International Standards for Phytosanitary Measures (ISPM) 15, "Guidelines for Regulating Wood Packaging Materials in International Trade." DOD shipments inside and outside of the United States must meet ISPM 15 whenever WPM is used to ship DOD cargo, or when wood is being acquired by DLA for future use as packaging material. WPM is defined as wood pallets, skids, load boards, pallet collars, wooden boxes, reels, dunnage, crates, frame and cleats. Packaging materials exempt from the requirements are materials that have undergone a manufacturing process, such as corrugated fiberboard, plywood, particleboard, veneer, and oriented strand board (OSD). All WPM shall comply with one of the following official quality control programs:

Heat Treatment (HT) or Kiln Dried Heat Treatment (KD HT) in accordance with American Lumber Standard Committee, Incorporated (ALSC) Wood Packaging Material Program and WPM Enforcement Regulations (see http://www.alsc.org/; or

All WPM shall include certification/quality markings in accordance with the ALSC or NWPCA standards, as applicable. Markings shall be placed in an unobstructed area that will be readily visible to inspectors. Pallet markings shall be applied to the stringer or block on diagonally opposite sides of the pallet and be contrasting and clearly visible.

All containers shall be marked on a side other than the top or bottom, contrasting and clearly visible. All dunnage used in configuring and/or securing the load shall also comply with ISPM 15 and be marked with an ASLC approved DUNNAGE stamp. Failure to comply with the requirements of this restriction may result in refusal, destruction, or treatment of materials at the point of entry. The Agency reserves the right to recoup from the Contractor any remediation costs incurred by the Government."

PALLET SHALL BE 4 WAY ENTRY, WINGED TYPE. PALLETIZED LOAD DIMENSIONS SHALL NOT EXCEED

43 INCHES IN LENGTH, 52 INCHES IN WIDTH, AND 54 INCHES IN HEIGHT (INCLUDING THE

PALLET).

THE PALLETIZED LOAD SHALL BE BONDED USING APPROVED COMMERCIAL BONDING MATERIALS. THE

USE OF METAL BANDING, IN SECURING BOXES TO PALLETS, IS DISCOURAGED. PALLET LOADS

SHALL CONTAIN THE SAME NUMBER OF CARTONS, OF IDENTICAL QUANTITIES, OF ONE NSN, TO THE

MAXIMUM EXTENT POSSIBLE.

PALLET LOADS CONTAINING MORE THAN ONE NSN SHALL BE CLEARLY MARKED TO LIST ALL THE NSN'S CONTAINED IN THE LOAD. NO CARTON SHALL HAVE MORE THAN ONE NSN. AT THE END OF A SIZE RUN, NO MORE THAN ONE CARTON PER NSN MAY BE SHORT OR OVER THE SPECIFIED QUANTITY.

SAID CARTON SHALL BE CLEARLY MARKED "SHORT" OR "OVER".

MIL-STD-147 IS REFERENCED FOR PALLETIZED LOADS.

LIST OF DOCUMENTS, EXHIBITS, AND OTHER ATTACHMENTS

a. This solicitation/award consists of the following documents, exhibits, and other attachments

b. DLA Troop Support Clothing & Textiles Additional Quality Assurance Requirements dated October 2018, which has superseded DSCPM 4155.3, QUALITY SYSTEMS REQUIREMENTS, dated NOVEMBER 3, 1997.

c. DLA Troop Support Clothing and Textiles Additional Quality Assurance Requirements dated October 2018 additional changes:

Page 10 of 38, par. 2.1, line 4, after "(DCMA QAS)" add ", or Supplier's Source Sampling Representative, as applicable"

Page 11 of 38, par. 2.3, line 2, delete "to the source QAS". Line 4, delete "source QAS" and replace with "Supplier's Source Sampling Representative". Page 12, par 2.3 (continued), delete "source QAS" and replace with "Supplier's Source Sampling Representative".

Page 12 of 38, par. 2.4, line 5, delete "as required" and replace with "if required".

Page 12 of 38, par. 3.1.1, after "entirely" add the following: "For routine shade or physical testing of fabric lots, Government sampling is not required. The DD Form 1222 for routine shade or physical testing of fabric lots shall be signed and dated by the Supplier's Source Sampling Representative in Box 15."

Page 13 of 38, par. 3.1.2 - line 10, after "Government QAS" add the following: "or Supplier's Source Sampling Representative, as applicable,"

Page 14 of 38, par. 3.2.1 -line 4, delete "source QAS" and replace with "Supplier's Source Sampling Representative".

Page 14 of 38, par. 3.2.1.1 - cutting swatches, delete "DCMA QAS" and replace with "Supplier's Source Sampling Representative". After "single color rolls - 4"x 24"" delete "QAS" and replace with "Supplier's Source Sampling Representative". After "multi-color camouflage"... delete "QAS" and replace with "Supplier's Source Sampling Representative".

Page 14 of 38, par. 3.2.1.2 - line 3, delete "stamped,". Line 4, Delete "source QAS" and replace with "Supplier's Source Sampling Representative"

Page 15 of 38, par. 3.2.1.4 - subpar. 2, delete "source QAS" and replace with "Supplier's Source Sampling Representative"

Page 15 of 38, par. 3.2.2 - Line 3, delete "stamped,", delete "source QAS" and replace with "Supplier's Source Sampling Representative". Line 4, delete "QAS" and replace with "Supplier's Source Sampling Representative".

Page 16 of 38, par. 3.3.1 - Line 2, after "(30)" add, "calendar". Line 3 and Line 6, after "QAS" add, "or Supplier's Source Sampling Representative"

Page 16 of 38, par. 3.3.2 - Delete the paragraph in its entirety, including subparagraphs labeled "a" through "i", and replace with the following:

"3.3.2. Contractor Furnished Material (CFM). DLA Troop Support Clothing and Textiles contracts require source sampling of CFM at finishing plants. The following provisions apply to sample selection and lot acceptance.

(a) The samples shall be randomly selected by the Supplier's Source Sampling Representative.

(b) Upon presentation of a lot, the Supplier's Source Sampling Representative will draw samples and forward the samples to the contractor's laboratory specified in the contract for testing.

(c) Shipment of Component Lots from the source to the prime contractor need not be deferred except for Government Acceptance Testing (i.e., shade evaluation).

Commencement of production prior to receipt of a passing test report from the contractor's authorized laboratory is solely at the contractor's risk.

(d) The contractor will provide copies of Certificates of Compliance to the QAS.

(e) The contractor is required to ensure that a complete test report for all lots is furnished to the source's QAS and the appropriate DLA-PTC representative."

Pages 24, 25, 36 add to block 16: "By signing in box 15, I certify that the samples referenced above were randomly selected and represent the lot identified above.

**Special note: Contractors shall ensure that blocks 2 and 15 of the form DD1222 are updated to reflect the correct information. Historically, both blocks contained the information of the DCMA QAR and their stamp/signature. When contractor's representative samples, these blocks shall include the contractor's representative's information. Block 17 shall still include the DCMA QAR to receive the results of the report even though they may not be sampling the material to be tested.