Tech Data PGC 00003 July 2024.pdf

SECTION C- DESCRIPTION/SPECIFICATION

COVERALLS,UTILITY (IFRV) PGC00003

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL

AND QUALITY REQUIREMENTS FOUND ON THE WEB AT:

http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx

FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE

MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT

INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.

RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT

RQ001: TAILORED HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS (MANUFACTURERS AND NON-

MANUFACTURERS)

RQ002: CONFIGURATION CHANGE MANAGEMENT - ENGINEERING CHANGE PROPOSAL REQUEST FOR

VARIANCE (DEVIATION OR WAIVER)

RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN

RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES

RQ018: CONTRACTOR RETENTION OF SUPPLY CHAIN TRACEABILITY DOCUMENTATION (AUG 2016) This item requires supply chain traceability documentation in accordance with DLA Directive (DLAD) Procurement Notes #C03 Contractor Retention of Supply Chain Traceability Documentation (AUG 2016)#. The full text of C03 can be found in the DLAD Procurement Notes on the Web at:

http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx.

(End of TQ Requirement)

IP056: MERCURY OR MERCURY COMPOUNDS ARE PROHIBITED IN PRESERVATION, PACKAGING, PACKING

AND MARKING.

Article Size NSN UPC

34XS 8415016612047 718020819334

34S 8415016612064 718020971780 34R 8415016612065 718020872421

36XS 8415016612071 718020799391

36S 8415016612076 718020926698 36R 8415016612078 718020934617 36L 8415016612082 718020715117

38XS 8415016612273 718020811376

38S 8415016612277 718020844381 38R 8415016612279 718020974903 38L 8415016612287 718020876214

38XL 8415016612293 718020844770

40XS 8415016612314 718020706290

40S 8415016612325 718020748672 40R 8415016612327 718020841274 40L 8415016612337 718020680699

40XL 8415016612338 718020809236

40XXL 8415016612349 718020804750

40XXXL 8415016612363 718020694597

42XS 8415016612370 718020739427

42S 8415016612375 718020863689 42R 8415016612464 718020634227 42L 8415016612472 718020648293

42XL 8415016612478 718020819433

42XXL 8415016612674 718020678092

44S 8415016612676 718020682433 44R 8415016612680 718020681672 44L 8415016612683 718020731469

44XL 8415016612711 718020629216

44XXL 8415016612718 718020675060

46S 8415016612733 718020832401 46R 8415016612736 718020896922 46L 8415016612741 718020771472

46XL 8415016612758 718020970578

46XXL 8415016612793 718020944449

48R 8415016612798 718020696287 48L 8415016612812 718020628684

48XL 8415016612826 718020862842

48XXL 8415016612828 718020935911

50R 8415016612833 718020843407 50L 8415016612839 718020935768

50XL 8415016612844 718020839790

50XXL 8415016612849 718020679143

52R 8415016612887 718020927022 52L 8415016612890 718020920603

52XL 8415016612894 718020815138

52XXL 8415016612895 718020670133

54L 8415016612897 718020996257

54XL 8415016612899 718020953281

54XXL 8415016612903 718020722191

56R 8415016612904 718020914930

IFRV UTILITY COVERALLS

Coveralls shall be made in accordance with NCTRF-CID-55095, Dated January 31, 2017

Pattern Date: 22 February 2017

Shade Standard Samples of Cloth, Navy Shade Blue 3392, is Available for Shade # Piece No. 17265 for Blend "A" 48% modacrylic, 32% Loyocell and 20% aramid flame resistant woven cloth Piece No. 18082 for Blend "B" 65% modacrylic, 33% aramid, and 2% anti-static flame resistant woven cloth.

Additional Information for NCTRF-CID-55095:

Page 1, paragraph 2.2 At end of page insert: "DISTRIBUTION STATEMENT A: Approved for public release."

Page 2, paragraph 3.1, line 15 delete and substitute: "The coveralls shall have a hanger loop with a 2-inch (± 1/2) free opening positioned inside the back neck"

Page 2, paragraph 3.1.1.1, line 1 Delete "Front patch pockets" and substitute "Breast patch pockets".

Line 4 Delete "They" and substitute "The".

Page 3, paragraph 3.1.5, After line 3 add:

"a. Undersleeve opening construction: Turn raw edge of underply extension up over itself, 1/2 inch from edge of sleeve tapering to 1/4 inch at top of sleeve opening.

Fold over body of material and stitch 1/16 inch from folded edge. Seam type EFb-1, stitch type 301.

b. Top sleeve opening construction: Turn raw edge of top ply facing under 1/2 (+1/16) inch. Fold back under body of material and stitch 1/16 inch from folded edge continuing across width of facing. Facing shall finish 1/2 (+1/16) inch in width. Seam type EFb-1, stitch type 301."

c. Place a 3/8 (+1/16) inch horizontal bartack superimposed on the stitching across facing width at the top of sleeve opening.”

Page 3, paragraph 3.1.2, Line 6, delete "1/2-inch size tack and 30 (± 2) stitches per tack" and substitute "1/2-inch long, 1/16-inch wide size tack with 28 (± 2) stitches per tack."

Page 3, paragraph 3.1.7, delete and substitute:

"3.1.7. Bartacks. Bartacks shall be stitched and positioned as indicted in Table I-1.

When counting the stitches in the bartack construction, the lay stitch shall be included. Bartacks shall be free from thread breaks loose stitching."

TABLE I-1. Bartacks

Size (Inches)

Stiches/ Bartack

Bartack Location

3/8 28 min 1 per slide fastener tape

Horizontal bartack on top folded ends of slide fastener tape

3/8 28 min 2 Horizontal bartack at top corner of hip pocket

3/8 28 min 1 per pocket

Vertical bartack at lower corner of front lower patch pocket opening

3/8 28 min 1 per pocket

Horizontal bartack at upper corner of front lower patch pocket opening

3/8 28 min 1 per sleeve

Horizontal bartack across seam allowance at top of sleeve opening

3/8 28 min 2 per flap

Vertical bartack superimposed on inner row of stitching on bottom corner of all pocket flaps

3/8 28 min 2 Vertical bartack according to marks on pattern for pencil pocket opening

1/2 30 min 1 Horizontal bartack on “J” stitching at top of crotch seam through all plies of slide fastener tape and left and right fronts of coveralls

1/2 30 min 2 per loop

Horizontal bartack on top and bottom edge of belt loops

Page 4, Paragraph 3.2.3, After line 4 add: "The cloth shall be products that are authorized by the certifying activity for listing on the applicable source control drawing, NCTRF Drawing 01-NCTRF-17, before contract award (see 7.5). Unless otherwise specified in the contract the certification sample yardage shall be 5 yards. The cloth shall be certified through inspection and examination for the cloth salient characteristics specified in this document when tested as specified in 3.2.3, 3.2.3.1 and Table I. The certification inspection shall be unacceptable if the requirements are not met."

Page 4, Table I, Row 2, Delete: "7.0" and "8.0" from Type II, Class 1, Color C requirements and replace with: "See drawing 01-NCTRF-17"

Page 5 and 6, Delete Flame Resistance Row 10 entire block and Flame Resistance Row 1 entire block and replace with:

Characteristics Test Method Requirements

Type I Type II

Class 1, Color A & Class 2

Class 1, Color B Class 1, Color C

Flame Resistance, Initial After Flame, seconds

(maximum)

After Glow, seconds (maximum)

Char Length, inches (maximum)

ASTM D6413 N/A

2.0

5.0

25.0

Flame Resistance, After 25 home launderings After Flame, seconds

(maximum)

After Glow, seconds (maximum)

Char Length, inches (maximum)

AATCC-135, 1, V, Ai &

ASTM D6413

N/A

25.0

Page 6, paragraph 3.2.4, line 4 delete "or "good".

Page 7, paragraph 3.2.6, line 3, delete "minimum".

Page 9, paragraph 3.4, line 6, delete " The top and side of the pocket flaps, the" and substitute "The top and side edges of the pocket flaps shall be double stitched 1/16-inch from folded edge with a 1/4-inch gauge. The".

Page 15, paragraph 5.2, End item examination Line 2, after "MIL-STD-1668" delete "except that table I shall not be used. Lots of coveralls shall be sampled as defined by contract, except where otherwise indicated."

Page 17, Paragraph 7.5, At end of paragraph, add new entry:

"f. When certification is required; name and address of certification activity (see

3.1.1 and 4.2.1)"

Page 17, Under "MILITARY INTERESTS" delete and substitute:

"Preparing Activity:

Navy-NU Custodians:

Navy-NU

DLA-CT"

LIST OF DOCUMENTS, EXHIBITS, AND OTHER ATTACHMENTS

a. This solicitation/award consists of the following documents, exhibits, and other attachments

b. DLA Troop Support Clothing & Textiles Additional Quality Assurance Requirements Revision 1 dated August 2021, which has superseded DLA Troop Support Clothing and Textiles Additional Quality Assurance Requirements dated October 2018.

ADDITIONAL INFORMATION FOR ANSI/ASQC Z1.4:

NOTE: THE MOST RECENT VERSION OF THIS DOCUMENT SHOULD BE USED.

APPLICATION FOR COPIES SHOULD BE ADDRESSED TO:

AMERICAN SOCIETY FOR QUALITY

600 NORTH PLANKINTON AVENUE

MILWAUKEE, WISCONSIN 53203

(Ref. T0795 - May 17, 2006)

SECTION D – PACKAGING AND MARKING

Case Lot is 24 Coveralls, of one size, type and class only, packed in each carton.

As a minimum item shall be packed in a snug fitting fiberboard shipping container conforming to ASTM-D-5118, Type CF, Style RSC, Grade 275, variety SW, Class domestic, with a double wall liner. Any commercial closure method cited in ASTM-D-1974 is acceptable except stapling.

Packaging shall be as per ASTM-D-3951, MIL-STD-129 MIL-STD-147. Lot numbering shall be in accordance with MIL-STD-129 AND DLA Troop Support Clothing & Textiles Additional Quality Assurance Requirements