TECH DATA.pdf

HAT, SERVICE, PISTON-RIFLE TEAM INSTRUCTIONS

RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN

RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY

REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH

IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL AND QUALITY

REQUIREMENTS FOUND ON THE WEB AT:

http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx

FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN

EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE

CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN

EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION

AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE

AMENDMENT DATE CONTROLS.

FUR FELT, OLIVE DRAB

THE HAT SERVICE WITH CHIN STRAP, ARMY/MARINE

CORPS OLIVE DRAB, PATTERN DATED 21 FEBRUARY 1995

THE FOLLOWING STANDARD SAMPLES ARE AVAILABLE

FROM DLA TROOP SUPPORT AND APPLICABLE:

OLIVE DRAB FUR FELT FOR SHADE ONLY.

(Ref. W0346) Page 1, paragraph 2.1, lines 3 and 4, delete "sewn with concealed hand stitching" and substitute: "hand or machine sewn with 4 concealed tack stitches under the bow and 4 tack stitches on the corners of the bow that do not have to be concealed";

line 5, after "brass" insert "or aluminum."

Page 2, paragraph 2.2.4 line 5 add to ten right after nine, line 5 add approximately right after strap. paragraph 2.2.6 line delete 3-1/2 (=1/8) and substitute 3-1/2 to 4-1/2, line 5, delete 80 hours and substitute 40, paragraph 2.2.7 line 5, delete should be referred to the Air Force and substitute shall be black.

Page 2, paragraph 2.26 Grosgrain 100% polyester ribbon approved for use in-lieu of rayon ribbon.

Page 3, paragraph 2.4, line 1, delete an additional printed cloth label and substitute it is embossed on sweatband or a gummed label.

ADDITIONAL INFORMATION FOR COMMERCIAL AQL'S:

AQL'S FOR COMMERCIAL ITEM DESCRIPTIONS (CID'S):

VISUAL - GENERAL INSPECTION LEVEL II, AQL - 1.0

DIMENSIONAL - SPECIAL INSPECTION LEVEL S-2, AQL - 2.5

ACCEPTABILITY OF LOTS WILL BE DETERMINED BY THE USE

OF "SAMPLING PROCEDURES AND TABLES FOR INSPECTION BY

ATTRIBUTES", ANSI/ASQC Z1.4

(ref. T1921)

ADDITIONAL INFORMATION FOR PPP-B-636:

FEDERAL SPECIFICATION PPP-B-636 DATED JULY 12, 1981, INCLUDING

INTERIM FEDERAL SPECIFICATION PPP-B-636L DATED JANUARY 1, 1991,

IS HEREBY CANCELLED, AND REPLACED WITH ASTM-D-5118, STANDARD

PRACTICE FOR FABRICATION OF FIBERBOARD SHIPPING BOXES, AND ASTM-

D-1974, STANDARD PRACTICE FOR METHOD OF CLOSING, SEALING AND

REINFORCING FIBERBOARD SHIPPING CONTAINERS.

(ref. T0605)

"MIL-DTL-32075: LABEL FOR CLOTHING, EQUIPAGE,

AND TENTAGE, GENERAL USE REPLACES DDD-L-20

(Ref. T0451 - June 19, 2007)

INTERIM SPECIFICATION CHANGES TO MIL-DTL-32075:

PAGE 6, TABLE I, "PHYSICAL REQUIREMENTS OF THE

TYPE VI FINISHED LABEL." UNDER "TEARING

STRENGTH" DELETE: "(LB.) MINIMUM" AND

SUBSTITUTE: "(GNS) MINIMUM."

PAGE 12, PARA 3.3.2.17, AFTER "NSN" ADD

"AND THE UNIVERSAL PRODUCT CODE (UPC)

SUPPLIED BY THE GOVERNMENT, FOR ALL NSNs."

ADDITIONAL INFORMATION FOR FED-STD-191:

FED-STD-191A NOTICE 7, DATED AUGUST 9, 2000 IS HEREBY INACTIVE

FOR NEW DESIGN. WHEN NOT USING FED-STD-191, SEE INTERIM CHANGES

TO END ITEM SPECIFICATION FOR REPLACEMENT ASTM.

INTERIM CHANGES TO FED-STD-191A:

TEST METHOD 5202, PARA. 5.3, DELETE FIRST SENTENCE AND

SUBSTITUTE: "THE SPECIMEN SHALL BE CLAMPED FIRMLY, WITH ONE END

FLUSH WITH THE OUTER EDGE OF THE VISE, SUCH THAT ONE INCH OF

SPECIMEN LIES WITHIN THE CLAMP AND ONE INCH OF THE SPECIMEN

EXTENDS BEYOND THE CENTER OF ROTATION (FACE OF THE VISE), AND

WITH THE LONG EDGE PARALLEL TO THE FACE OF THE DIAL PLATE".

TEST METHOD 5309.1 ABRASION RESISTANT OF TEXTILE WEBBING. PAGE

1, PARA 4.1.2,LINE 4: DELETE "B-97" AND SUBSTITUTE "B-91".

THE FOLLOWING METHODS ARE IDENTIFIED AS SPECIFYING OZONE

DEPLETING SUBSTANCES: 1100, 1200, 1240, 1400, 1410, 1500,

1510,1520,1530, 1540, AND 1550. PARA 5.1 OF THESE TEST METHODS

REQUIRE THE USE OF 1,1,1- TRICHLOROETHANE, ALCOHOL OR ETHER.

1,1,1-TRICHLORETHANE IS AN OZONE DEPLETING SUBSTANCE (METHYL

CHLOROFORM) AND IS THEREFORE PROHIBITED. THE USE OF EITHER

ALCOHOL OR ETHER IS REQUIRED WHEN THESE METHODS ARE IN BASIC OR

ANY REFERENCED DOCUMENT.

METHOD 5202, STIFFNESS OF CLOTH, DIRECTIONAL; CANTILEVER BENDING

METHOD. PAGE 2, PARA. 5.3 DELETE FIRST SENTENCE AND SUBSTITUTE

WITH THE FOLLOWING: "THE SPECIMEN SHALL BE CLAMPED FIRMLY, WITH

1 END FLUSH WITH THE OUTER EDGE OF THE VISE, SUCH THAT 1" OF THE

SPECIMEN LIES WITHIN THE CLAMP AND 1" OF THE SPECIMEN EXTENDS

BEYOND THE CENTER OF ROTATION (INNER FACE OF THE VISE) AND WITH

THE LONG EDGE PARALLEL TO THE FACE OF THE DIAL PLATE."

METHOD 5556.1, MOBILE LAUNDRY EVALUATION FOR TEXTILE MATERIALS,

PAGE 5, PARA. 5.2.2, LINE 8: DELETE SENTENCE BEGINNING WITH "THE

SPECIMENS AND BALLAST" IN ITS ENTIRETY AND SUBSTITUTE WITH THE

FOLLOWING: "THE SPECIMENS AND BALLAST SHALL BE SEPARATED, OPENED

TO FULL WIDTH AND PLACED IN A PRE-HEATED DRYER HAVING A STACK

TEMPERATURE OF 140-180 DEG. F. THIS TEMPERATURE RANGE

CORRESPONDS TO A SETTING OF "HIGH" ON THE TEMPERATURE INDICATOR

ON THE DRYER. DRYING SHALL CONTINUE FOR 45-60 MINUTES OR UNTIL

SAMPLES ARE DRY IN A ROTATING TUMBLE DRYER."

PAGE 5, PARA. 5.2.3, LINE 8: DELETE SENTENCE BEGINNING WITH "THE

SPECIMENS AND BALLAST" IN ITS ENTIRETY AND SUBSTITUTE WITH THE

FOLLOWING: "THE SPECIMENS AND BALLAST SHALL BE SEPARATED, OPENED

TO FULL WIDTH AND PLACED IN A PRE-HEATED DRYER HAVING A STACK

TEMPERATURE OF 140-180 DEG. F. THIS TEMPERATURE RANGE

CORRESPONDS TO A SETTING OF "HIGH" ON THE TEMPERATURE INDICATOR

ON THE DRYER. DRYING SHALL CONTINUE FOR 35-40 MINUTES OR UNTIL

SAMPLES ARE DRY."

METHOD 5931, ELECTROSTATIC DECAY OF FABRICS; DETERMINATION OF

PAGE 1, PARA. 3: AFTER NUMBER OF DETERMINATIONS ADD "PER SAMPLE

UNIT". PAGE 1, PARA. 4: DELETE "APPARTUS" AND SUBSTITUTE

"APPARATUS". PAGE 1, PARA. 5.1, LINE 3: AFTER "AT"

DELETE"APPROXIMATELY".

PAGE 2, PARA. 5.2, LINES 2, AND 5: AFTER "OF" ADD "+-". LINE 6:

AFTER "TO" ADD "+-".

PAGE 2, PARA. 5.3: DELETE IN ITS ENTIRETY AND SUBSTITUTE WITH

THE FOLLOWING:"5.3 MOUNT A SPECIMEN TIGHTLY ACROSS THE

ELECTRODES, CENTERING IT OVER THE SENSOR OPENING. THE SURFACE

OF THE TEST SPECIMEN (BACK OR FRONT) SHALL FACE THE SENSOR.

RECORD (OPTIONAL) THE RESIDUAL CHARGE LEVEL ON THE SAMPLE AS

SEEN BY THE SENSOR, INCLUDING POLARITY.

NOTE THAT TEST SAMPLES WITH THE RESIDUAL CHARGE LEVELS OF LESS

+500 VOLTS YIELD THE BEST RESULTS. APPLY +5000 VOLTS TO THE

ELECTRODES FOR A PERIOD OF 20 SECS. AT THE END OF THE 20 SECOND

PERIOD, THE HIGH VOLTAGE (5000 VOLTS) SHALL BE TURNED OFF AND

THE SPECIMENS IMMEDIATELY GROUNDED. THE VOLTAGE BEHAVIOR OF THE

SPECIMEN WITH RESPECT TO TIME SHALL BE PLOTTED ON THE RECORDER.

NOTE: IN SOME CASES, THE TEST EQUIPMENT WILL DISPLAY VOLTAGE AND

DECAY TIME INFORMATION AND A CHART RECORDER IS NOT NECESSARY."

PAGE 2, PARA. 5.4, LINE 3: DELETE SENTENCE BEGINNING WITH "IF

THE SPECIMEN DID" IN ITS ENTIRETY.

PAGE 2, PARA. 5.5: DELETE PARAGRAPH IN ITS ENTIRETY AND

SUBSTITUTE WITH THE FOLLOWING: "RECORD THE MAXIMUM VOLTAGE LEVEL

(INCLUDING POLARITY) AND DECAY TIME TO 10% OF THE MAXIMUM

VOLTAGE LEVEL ACHIEVED."

PAGE 2, PARA. 5.6, LINE 1: ADD THE FOLLOWING PRIOR TO 1ST

SENTENCE: "REVERSE VOLTAGE POLARITY REPEAT MEASUREMENT,

ANDRECORD RESULTS."

PAGE 3, PARA. 6.6: DELETE PARAGRAPH IN ITS ENTIRETY AND

SUBSTITUTE WITH THE FOLLOWING: "THE AVERAGE TIME TO DECAY TO

10%OF THE MAX VOLTAGE SHALL BE INCLUDED FOR EACH OF THE WARP &

FILLING DIRECTIONS, AS WELL AS THE OVERALL AVERAGE, FOR EACH

FABRIC TESTED. THESE WILL BE OBTAINED BY AVERAGING THE TEST

RESULTS (ABSOLUTE VALUE OF) TOGETHER FOR BOTH VOLTAGE

POLARITIES. UNLESS OTHERWISE STATED IN THE REQUIREMENTS

DOCUMENT, THE FABRIC SHALL BE CONSIDERED ACCEPTABLE IF

THEAVERAGE MAXIMUM VOLTAGE IN BOTH THE WARP AND FILLING

DIRECTIONS IS LESS THAN 4000 VOLTS, AND THE AVERAGE DECAY TIME

(TO 10% MAXVOLTAGE) IS GREATER THAN 0.5 SECONDS IN BOTH THE WARP

AND FILLING DIRECTIONS. IT SHALL BE INDICATED WHETHER THE

FABRIC IS ACCEPTABLE OR NON-ACCEPTABLE."

PAGE 3, PARA. 7.1, SECOND COLUMN, LINE 2: DELETE 406C AND

SUBSTITUTE WITH "406D".

AFTER PARA. 7.1, ADD THE FOLLOWING: "7.2 NOTE: IF THE MODEL 406D

STATIC DECAY METER, OR EQUIVALENT, IS USED, A CHART RECORDER

ISNOT MANDATORY FOR THE TEST."

(Ref. T0215)

INCLUDE T6855 OBJECT TEXT ID ST

ADDITIONAL INFORMATION FOR MIL-S-43993:

NO ADDITIONAL INFORMATION FOLLOWS.

(Ref. T1697)

MIL-STD-129R w/CHANGE 2 - DEPARTMENT OF DEFENSE STANDARD

PRACTICE MILITARY MARKING FOR SHIPMENT AND STORAGE

DATED: 27 SEPTEMBER 2019

INTERIM CHANGES:

OMISSION OF MARKINGS ON EXTERIOR SHIPPING CONTAINERS OF ITEMS

IN THE DLA TROOP SUPPORT CLOTHING AND TEXTILE (C&T) DIRECTORATE:

THE NOMENCLATURE AND MANUFACTURER'S NAME (WHEN THE NAME

IDENTIFIES THE MATERIAL) SHALL BE OMITTED FROM ALL EXTERIOR

SHIPPING CONTAINERS OF DLA TROOP SUPPORT C&T ITEMS, REGARDLESS

OF MODE OF SHIPMENT.

IF THE MANUFACTURER'S NAME DOES NOT IDENTIFY THE MATERIAL AS

BEING CLOTHING, IT MAY REMAIN. NSNS SHALL BE SHOWN ON ALL

SHIPPING CONTAINERS OF C&T ITEMS, THE PACKING LIST SHALL BE

PLACED INSIDE THE LAST CONTAINER TO BE LOADED FOR EACH SHIPMENT.

THE WORDS "PACKING LIST HERE" SHALL BE STENCILED, NOT HAND

LETTERED, ON THE CONTAINER.

(ref T0303)

MIL-STD-147E w/CHANGE 2

27 JUNE 2019

DEPARTMENT OF DEFENSE

STANDARD PRACTICE

PALLETIZED UNIT LOADS

(ref T0306)

ADDITIONAL INFORMATION FOR MIL-STD-2073-1:

NO ADDITIONAL INFORMATION FOLLOWS

(Ref. T0898)